Search NASA⌕ Search

SEARCH · Search NASA

Results for “Random vibration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

SRG110 Stirling Generator Dynamic Simulator Vibration Test Results and Analysis Correlation

The U.S. Department of Energy (DOE), Lockheed Martin (LM), and NASA Glenn Research Center (GRC) have been developing the Stirling Radioisotope Generator (SRG110) for use as a power system for space science missions. The launch environment enveloping potential missions results in a random input spectrum that is significantly higher than historical RPS launch levels and is a challenge for designers. Analysis presented in prior work predicted that tailoring the compliance at the generator-spacecraft interface reduced the dynamic response of the system thereby allowing higher launch load input levels and expanding the range of potential generator missions. To confirm analytical predictions, a dynamic simulator representing the generator structure, Stirling convertors and heat sources was designed and built for testing with and without a compliant interface. Finite element analysis was performed to guide the generator simulator and compliant interface design so that test modes and frequencies were representative of the SRG110 generator. This paper presents the dynamic simulator design, the test setup and methodology, test article modes and frequencies and dynamic responses, and post-test analysis results. With the compliant interface, component responses to an input environment exceeding the SRG110 qualification level spectrum were all within design allowables. Post-test analysis included finite element model tuning to match test frequencies and random response analysis using the test input spectrum. Analytical results were in good overall agreement with the test results and confirmed previous predictions that the SRG110 power system may be considered for a broad range of potential missions, including those with demanding launch environments.

Suarez, Vicente J.↗

Aircraft ground vibration testing at NASA Ames-Dryden Flight Research Facility

At the NASA Ames Research Center's Dryden Flight Research Facility at Edwards Air Force Base, California, a variety of ground vibration test techniques has been applied to an assortment of new or modified aerospace research vehicles. This paper presents a summary of these techniques and the experience gained from various applications. The role of ground vibration testing in the qualification of new and modified aircraft for flight is discussed. Data are presented for a wide variety of aircraft and component tests, including comparisons of sine-dwell, single-input random, and multiple-input random excitation methods on a JetStar airplane.

Kehoe, Michael W.↗

Aircraft ground vibration testing at NASA Ames-Dryden Flight Research Facility

At the NASA Ames Research Center's Dryden Flight Research Facility at Edwards Air Force Base, California, a variety of ground vibration test techniques has been applied to an assortment of new or modified aerospace research vehicles. This paper presents a summary of these techniques and the experience gained from various applications. The role of ground vibration testing in the qualification of new and modified aircraft for flight is discussed. Data are presented for a wide variety of aircraft and component tests, including comparison of sine-dwell, single-input random, and multiple-input random excitation methods on a JetStar airplane.

Kehoe, Michael W.↗

Microscopic description of large-amplitude shape-mixing dynamics with inertial functions derived in local quasiparticle random-phase approximation

On the basis of the adiabatic self-consistent collective coordinate method, we develop an efficient microscopic method of deriving the five-dimensional quadrupole collective Hamiltonian and illustrate its usefulness by applying it to the oblate-prolate shape coexistence/mixing phenomena in proton-rich {sup 68,70,72}Se. In this method, the vibrational and rotational collective masses (inertial functions) are determined by local normal modes built on constrained Hartree-Fock-Bogoliubov states. Numerical calculations are carried out using the pairing-plus-quadrupole Hamiltonian including the quadrupole-pairing interaction within the two major-shell active model spaces both for neutrons and protons. It is shown that the time-odd components of the moving mean-field significantly increase the vibrational and rotational collective masses in comparison with the Inglis-Belyaev cranking masses. Solving the collective Schroedinger equation, we evaluate excitation spectra, quadrupole transitions, and moments. The results of the numerical calculation are in excellent agreement with recent experimental data and indicate that the low-lying states of these nuclei are characterized as an intermediate situation between the oblate-prolate shape coexistence and the so-called {gamma} unstable situation where large-amplitude triaxial-shape fluctuations play a dominant role.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Probing the Collective Degrees of Freedom at the Proton Drip Line in the Extremely Neutron Deficient {sup 172}Hg

Excited states in the extremely neutron-deficient isotope {sup 172}Hg have been established for the first time. The {sup 96}Ru({sup 78}Kr,2n) reaction was employed to populate excited states in {sup 172}Hg with a cross section {sigma}{approx_equal} 15 nb. The highly selective Recoil-Decay Tagging (RDT) technique was used to obtain clean in-beam {gamma}-ray spectra for {sup 172}Hg. The yrast ground-state band has tentatively been established up to I = 6h-bar. The data have been interpreted within the framework of total Routhian surface and quasiparticle random phase approximation calculations. In addition to the well-known features of shape coexistence previously observed in light Hg isotopes, the systematic trends in the energy of the yrast 2{sup +} and 4{sup +} states in the chain of Hg isotopes indicate a pronounced vibrational collectivity which is reduced in strength, but at the same time shows a higher degree of harmonicity, as the neutron number decreases below the neutron midshell.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Direct dynamics simulation of dioxetane formation and decomposition via the singlet ·O–O–CH2–CH2 · biradical: Non-RRKM dynamics

Electronic structure calculations and direct chemical dynamics simulations are used to study the formation and decomposition of dioxetane on its ground state singlet potential energy surface. The stationary points for 1O2 + C2H4, the singlet {center_dot}O-O-CH2-CH2{center_dot} biradical, the transition state (TS) connecting this biradical with dioxetane, and the two transition states and gauche {center_dot}O-CH2-CH2-O{center_dot} biradical connecting dioxetane with the formaldehyde product molecules are investigated at different levels of electronic structure theory including UB3LYP, UMP2, MRMP2, and CASSCF and a range of basis sets. The UB3LYP/6-31G* method was found to give representative energies for the reactive system and was used as a model for the simulations. UB3LYP/6-31G* direct dynamics trajectories were initiated at the TS connecting the {center_dot}O-O-CH2-CH2{center_dot} biradical and dioxetane by sampling the TS's vibrational energy levels, and rotational and reaction coordinate energies, with Boltzmann distributions at 300, 1000, and 1500 K. This corresponds to the transition state theory model for trajectories that pass the TS. The trajectories were directed randomly towards both the biradical and dioxetane. A small fraction of the trajectories directed towards the biradical recrossed the TS and formed dioxetane. The remainder formed 1O2 + C2H4 and of these {approx} 40% went directly from the TS to 1O2 + C2H4 without getting trapped and forming an intermediate in the {center_dot}O-O- CH2-CH2{center_dot} biradical potential energy minimum, a non-statistical result. The dioxetane molecules which are formed dissociate to two formaldehyde molecules with a rate constant two orders of magnitude smaller than that predicted by Rice-Ramsperger-Kassel-Marcus theory. The reaction dynamics from dioxetane to the formaldehyde molecules do not follow the intrinsic reaction coordinate or involve trapping in the gauche {center_dot}O-CH2-CH2-O{center_dot} biradical potential energy minimum. Important non-statistical dynamics are exhibited for this reactive system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

AI-Assisted Conceptual Development of a Pre-Geometric Cosmological Model - An Exercise in AI-Assisted Conceptual Framework Generation, Paper I: Foundations and Replication Dynamics

We develop a pre-geometric cosmological framework in which existence is identified with a finite amount of unstructured energy possessing vibration as its only intrinsic property. This vibrational substrate occupies an open, bounded spectral interval $(\omega_{\min},\omega_{\max})$, ensuring finiteness of total energy and excluding infinitely stable configurations. The substrate evolves under two fundamental and competing tendencies---excitation, which amplifies coherence, and randomization, which scrambles it. Their balance produces a metastable unstructured regime in which rare fluctuations may form long-lived self-consistent spectral configurations. Because the substrate is finite and subject to competing order--disorder dynamics, no coherent configuration can be perpetually stable. We show that the only mechanism capable of sustaining long-lived organization is a replication instability: a coherent unit may reproduce into multiple offspring according to a general $1\!\to n$ rule. Replication consumes energy from the finite substrate, breaks the metastable symmetry, and induces a discrete notion of event time through the replication tick $\Delta\tau$. Temporal succession is defined through correlation ordering of spectral microstates, producing an intrinsic pre-causal structure. The compactness of the spectral domain imposes minimal and maximal timescales, bounds the internal coherence of emergent units, and limits their proliferation. These spectral constraints serve as precursors for the emergence of geometry, adjacency, and a limiting propagation speed, developed in subsequent papers of this series. Paper I provides the foundational axioms (PG1--PG9) governing the spectral substrate, its metastable dynamics, the formation of coherent units, and the necessity of replication, establishing a fully pre-geometric stage from which causal and geometric structure naturally emerge.

79 ASTRONOMY AND ASTROPHYSICS↗

Effects of Resistive Vibration Exercise Combined with Whey Protein and KHCO3 on Bone Tturnover Markers in Head-down Tilt Bed Rest (MTBR-MNX Study)

High protein intake further increases bone resorption markers in head-down tilt bed rest (HDBR), most likely induced by low-grade metabolic acidosis. Adding an alkaline salt to a diet with high protein content prevents this additional rise of bone resorption markers in HDBR. In addition, high protein intake, specifically whey protein, increases muscle protein synthesis and improves glucose tolerance, which both are affected by HDBR. Resistive vibration exercise (RVE) training counteracts the inactivity-induced bone resorption during HDBR. To test the hypothesis that WP plus alkaline salt (KHCO3) together with RVE during HDBR will improve bone turnover markers, we conducted a randomized, three-campaign crossover design study with 12 healthy, moderately fit male subjects (age 34+/-8 y, body mass [BM] 70 +/- 8 kg). All study campaigns consisted of a 7-d ambulatory period, 21days of -6 deg. head-down tilt bed rest (HDBR), and a 6-d recovery period. Diet was standardized and identical across phases. In the control (CON) campaign, subjects received no supplement or RVE. In the intervention campaigns, subjects received either RVE alone or combined with WP and KHCO3 (NEX). WP was applied in 3 doses per day of 0.6 g WP/kg BM together with 6 doses of 15 mmol KHCO3 per day. Eleven subjects completed the RVE and CON campaign, 8 subjects completed all three campaigns. On day 21 of HDBR excretion of the bone resorption marker C-telopeptide (CTX) was 80+/-28% (p<0.001) higher than baseline, serum calcium concentrations increased by 12 +/- 29% (p<0.001) and serum osteocalcin concentrations decreased by 6+/-12% (p=0.001). Urinary CTX excretion was 11+/- 25% (p=0.02) lower on day 21 of HDBR in the RVE- and tended to decrease by 3+/- 22% (p=0.06) in the NEX campaign compared to CON. Urinary calcium excretion was higher on day 21 in HDBR in the RVE and NEX (24+/- 43% p=0.01; 25+/- 37% p=0.03) compared to the CON campaign. We conclude that combination of RVE with WP/KHCO3 was not superior to RVE alone in any of these results.

Graf, Sonja↗

Viking orbiter 1975 articulation control actuators

The articulation subsystem actuators were rigorously tested in severe environments. They were operated through temperature ranges from -73 C to +121 C. In each case the temperature rate of change was at maximum. The actuator under test at room temperature was put into a pre-chilled or preheated chamber. Satisfactory performance was obtained throughout this full temperature range and under the temperature shock conditions above. However, at temperatures below -78 C some leakage was experienced through the O-ring seal around the shaft. The actuators were subjected to severe vibration and 500 g shock test with a time duration of 0.0007 seconds. The scan actuator was life tested by operating it from stop to stop through 2,000 cycles with 20,000 start-stop procedures randomly distributed through the 2,000 cycles.

Perkins, G. S.↗

Vibroacoustic study of the NASA Goddard Space Flight Center OSS-1 payload

A comparative evaluation of shuttle liftoff and ground test random response data obtained from the Office of Space Science-1 (OSS-1) pallet payload flown in the cargo bay of STS-3 is presented. The study was initiated to evaluate the possibility that the payload flight vibration response can exceed that occurred during ground test when the ground test acoustic excitation is normalized to the flight acoustic environment. In addition, the analytically derived response from the Vibroacoustic Payload Environment Prediction System (VAPEPS) is compared with OSS-1 ground test results.

Lee, Y. A.↗

Intrepid MCMC: Metropolis-Hastings with exploration

In engineering examples, one often encounters the need to sample from unnormalized distributions with complex shapes that may also be implicitly defined through a physical or numerical simulation model, making it computationally expensive to evaluate the associated density function. For such cases, MCMC has proven to be an invaluable tool. Random-walk Metropolis Methods (also known as Metropolis-Hastings (MH)), in particular, are highly popular for their simplicity, flexibility, and ease of implementation. However, most MH algorithms suffer from significant limitations when attempting to sample from distributions with multiple modes (particularly disconnected ones). Here, in this paper, we present Intrepid MCMC - a novel MH scheme that utilizes a simple coordinate transformation to significantly improve the mode-finding ability and convergence rate to the target distribution of random-walk Markov chains while retaining most of the simplicity of the vanilla MH paradigm. Through multiple examples, we showcase the improvement in the performance of Intrepid MCMC over vanilla MH for a wide variety of target distribution shapes. We also provide an analysis of the mixing behavior of the Intrepid Markov chain, as well as the efficiency of our algorithm for increasing dimensions. A thorough discussion is presented on the practical implementation of the Intrepid MCMC algorithm. Finally, its utility is highlighted through a Bayesian parameter inference problem for a two-degree-of-freedom oscillator under free vibration.

97 - MATHEMATICS AND COMPUTING↗

g factors of first 2{sup +} states of neutron-rich Xe, Ba, and Ce isotopes

Using new techniques developed for measuring angular correlations with large detector arrays, the g factors of 2{sup +} states in {sup 140,142}Xe are measured for the first time by the method of correlation attenuation in randomly oriented magnetic fields. g factors in {sup 146}Ba and {sup 146,148}Ce are measured to establish the method by comparison with previous values. The results are discussed in terms of IBM-2 and rotation-vibration models.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Assessment of Potential Ergonomic Injury Risk in the Nuclear Material Processing Glovebox Environment [Capstone Project]

Gloveboxes are isolation barriers that are used within many different industries such as pharmaceuticals, electronic parts fabrication, nuclear, and biological. The research on glovebox ergonomics is currently limited with few ergonomic professionals that focusing exclusively on glovebox working environments. There is existing documentation on occupational injuries, such as musculoskeletal disorders (MSD), sustained as a direct result of working in gloveboxes. The main elements that pose ergonomic risks to glovebox workers are operational repetition, duration, force, vibration, lifting heavy (more than 15lbs with two hands) objects, and awkward postures. This paper examines a small sample of the potential causal or risk factors that lead to the ergonomic injuries. A meta-analysis utilizing a random effect model is used to examine data from several studies which focus on, dexterity and strength changes as result of glove thickness, and robotic assistive technology as a means to improve postural mechanics. With the meta-analysis technique, similar data sets from different research studies can be coalesced into a single weighted, statistically significant result for subsequent consideration. The results from the analysis show that increased glove thickness results in decreased dexterity for operators thus increasing ergonomic risk factors such as task duration. It is also shown that glove thickness decreases grip strength but a similar decrease in pinch strength is not definitively demonstrated. With decreased grip strength, operators will need to exert more force (a known ergonomic risk factor) on processing tools, etc. during operations thus increasing the risk of ergonomic injury. The use of robotic assistive technology as a means to improve operator posture (risk factor) was also examined. Although it may be intuitively assumed that human-robotic collaboration would be beneficial in reducing risk factors, the result from this study’s analysis was not statistically significant. It is inferred that with additional directed research on this topic another study/analysis could be statistically significant demonstrating the benefits of the technology.

99 GENERAL AND MISCELLANEOUS↗

On-Orbit System Identification

Information derived from accelerometer readings benefits important engineering and control functions. Report discusses methodology for detection, identification, and analysis of motions within space station. Techniques of vibration and rotation analyses, control theory, statistics, filter theory, and transform methods integrated to form system for generating models and model parameters that characterize total motion of complicated space station, with respect to both control-induced and random mechanical disturbances.

Mettler, E.↗

Limits on the isolation of stochastic vibration for microgravity space experiments

The limitations on the isolation of stochastic vibrations for microgravity space experiments are explored. These limitations result from the restricted interior space available for vibration isolation. A one-degree-of-freedom representation of the experiment-spacecraft system is used, and an ideal vibration actuator is assumed. A kinematic representation results, and the problem becomes one of finding the minimum acceleration trajectory within a pair of stochastic walls. The wall motion is characterized by an ergodic, stationary, zero-mean, Gaussian random process with known power spectral density. The geometry of the wall trajectories is defined in terms of their significant extrema and zero crossings. This geomemtry is used in defining a composite trajectory that has a mean square acceleratiaon lower than that on the optimal path satisfying the stochastic wall inequality constraints. The optimal control problem is solved on a return path yielding the mean square acceleration in terms of the distributions of significant maxima and first-passage time of the wall process. The methodology is applied to a microgravity isolation problem to find the lower bounds on root-mean-square acceleration given the disturbance power spectral density.

Knospe, C. R.↗

Frequency domain analysis of the random loading of cracked panels

The primary effort concerned the development of analytical methods for the accurate prediction of the effect of random loading on a panel with a crack. Of particular concern was the influence of frequency on the stress intensity factor behavior. Many modern structures, such as those found in advanced aircraft, are lightweight and susceptible to critical vibrations, and consequently dynamic response plays a very important role in their analysis. The presence of flaws and cracks can have catastrophic consequences. The stress intensity factor, K, emerges as a very significant parameter that characterizes the crack behavior. In analyzing the dynamic response of panels that contain cracks, the finite element method is used, but because this type of problem is inherently computationally intensive, a number of ways of calculating K more efficiently are explored.

Doyle, James F.↗

Ionic Liquid versus Li+ Aqueous Solutions: Water Dynamics near Bistriflimide Anions

In this work, the ultrafast dynamics of concentrated aqueous solutions of the salt lithium bistriflimide and the ionic liquid 1-ethyl-3-methylimidazolium bistriflimide (EmimNTf 2 ) were studied using two-dimensional infrared (2D IR) vibrational echo and polarization-selective IR pump-probe techniques to monitor water’s hydroxyl stretch. Two distinct populations of hydroxyl groups, with differing vibrational lifetimes, are detected in solution – those engaged in hydrogen bonds to other water molecules or to the bistriflimide anion. Water molecules with the same hydrogen bond partner exhibit similar vibrational lifetimes in the two solutions. The reorientation dynamics of the anion-associated waters are also similar in form in the two solutions, showing a restricted wobbling-in-a-cone motion followed by a slower diffusive orientational randomization. However, the wobbling motions are much more angularly restricted in the ionic liquid solution. Spectral diffusion dynamics, which track the structural fluctuations of water’s hydrogen bonds, are very different in the two solutions. Water in the ionic liquid solution experiences much faster fluctuations overall and shows a greater extent of motional narrowing, resulting in a larger homogeneously broadened component in the spectral line, compared to the aqueous lithium salt. Thus, even when the hydroxyls of water associate with the same anion in solution, the cation identity and extent of ionic ordering (i.e., salt solution versus ionic liquid) can play an important role in determining the structural fluctuations experienced by a small hydrogen bonded solute.

14 SOLAR ENERGY↗

Technology Development for a Stirling Radioisotope Power System for Deep Space Missions

NASA Glenn Research Center and the Department of Energy (DOE) are developing a Stirling convertor for an advanced radioisotope power system to provide spacecraft on-board electric power for NASA deep space missions. NASA Glenn is addressing key technology issues through the use of two NASA Phase 2 SBIRs with Stirling Technology Company (STC) of Kennewick, WA. Under the first SBIR, STC demonstrated a 40 to 50 fold reduction in vibrations, compared to an unbalanced convertor, with a synchronous connection of two thermodynamically independent free-piston Stirling convertors. The second SBIR is for the development of an Adaptive Vibration Reduction System (AVRS) that will essentially eliminate vibrations over a mission lifetime, even in the unlikely event of a failed convertor. This paper discusses the status and results for these two SBIR projects and also presents results for characterizing the friction factor of high-porosity random fiber regenerators that are being used for this application.

Thieme, Lanny G.↗