Search NASA⌕ Search

SEARCH · Search NASA

Results for “Recovery Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Flexor bias of joint position in humans during spaceflight

The ability to estimate ankle and elbow joint position was tested before, during, and after a 17-day spaceflight. Subjects estimated targeted joint angles during isovelocity (IsoV) joint movements with agonist muscle groups either active or relaxed. These movements included elbow extension (EE) and elbow flexion (EF), and plantarflexion (PF) and dorsiflexion (DF) of the ankle. Subjects also estimated these joint positions while moving the dynamometer at their chosen (variable) velocity (VarV) during EE and PF. For IsoV tests, no differences were observed between active and passive movements for either the ankle or elbow. Compared with those of pre-flight test days, estimates of targeted elbow joint angles were approximately 5 degrees to 15 degrees more flexed in-flight, and returned toward the pre-flight values during recovery. The spaceflight effects for the ankle were inconsistent and less prevalent than those for the elbow. The VarV PF test condition for the 120 degrees target angle at the ankle exhibited approximately 5 degrees to 7 degrees more DF target angle estimates in-flight compared with those pre- or post-flight. In contrast, during IsoV PF there was a tendency for ankle estimates to be approximately 2 degrees to 3 degrees more PF after 2-3 days exposure to spaceflight. These data indicate that during spaceflight the perception of elbow extension is greater than actuality, and are consistent with the interpretation that microgravity induced a flexor bias in the estimation of the actual elbow joint position. Moreover, these effects in joint proprioception during spaceflight were observed in individual isolated single-joint movements during tasks in which vestibular function in maintaining posture were minimal.

STS-78 Shuttle Project↗

Recovery of atmospheric parameters from the Apollo/Soyuz-ATS-F radio occultation data

As part of the Apollo-Soyuz Test Project, Apollo was tracked in the satellite-to-satellite tracking mode by ATS-F. The tracking data obtained at occultation of Apollo by the earth has been used in this study to compute atmospheric parameters like pressure and temperature. The results of the numerical inversion have been compared with data from a radiosonde station near the occultation site. Near the surface of the earth, the refractivity computed from occultation data agreed with the radiosonde-derived values to within 3%. A pressure profile deduced from the refractivity profile by using a simplified model of the atmosphere showed good agreement with radiosonde measurements.

Rangaswamy, S.↗

Modeling of membrane processes for air revitalization and water recovery

Gas-separation and reverse-osmosis membrane models are being developed in conjunction with membrane testing at NASA JSC. The completed gas-separation membrane model extracts effective component permeabilities from multicomponent test data, and predicts the effects of flow configuration, operating conditions, and membrane dimensions on module performance. Variable feed- and permeate-side pressures are considered. The model has been applied to test data for hollow-fiber membrane modules with simulated cabin-air feeds. Results are presented for a membrane designed for air drying applications. Extracted permeabilities are used to predict the effect of operating conditions on water enrichment in the permeate. A first-order reverse-osmosis model has been applied to test data for spiral wound membrane modules with a simulated hygiene water feed. The model estimates an effective local component rejection coefficient under pseudosteady-state conditions. Results are used to define requirements for a detailed reverse-osmosis model.

Lange, Kevin E.↗

Long-Duration Testing of a Temperature-Swing Adsorption Compressor for Carbon Dioxide for Closed-Loop Air Revitalization Systems

This paper describes the results of long-duration testing of a temperature-swing adsorption compressor that has application in the International Space Station (ISS) and future spacecraft for closing the air revitalization loop. The air revitalization system of the ISS operates in an open loop mode and relies on the resupply of oxygen and other consumables from Earth for the life support of astronauts. A compressor is required for delivering the carbon dioxide from a removal assembly to a reduction unit to recover oxygen and thereby closing the air-loop. The TSAC is a solid-state compressor that has the capability to remove CO2 from a low-pressure source, and subsequently store, compress, and deliver at a higher pressure as required by a processor. The TSAC is an ideal interface device for CO2 removal and reduction units in the air revitalization loop of a spacecraft for oxygen recovery. The TSAC was developed and its operation was successfully verified in integration tests with the flight-like Carbon Dioxide Removal Assembly (CDRA) at Marshall Space Flight Center prior to the long-duration tests. Long-duration tests reveal the impacts of repeated thermal cycling on the compressor components and the adsorbent material.

Rosen, Micha↗

Development of an Ejectable Data Recorder Ejection Mechanism for the Low Earth Orbit Flight Test of an Inflatable Decelerator

On November 10, 2022, the 1100kg (2,425 lbs.) LOFTID Reentry Vehicle (RV) was launched on a United Launch Alliance Atlas V as a secondary payload with the Joint Polar Surveyor System-2. The 6-meter diameter (~20 ft.) aeroshell (a type of heat shield) entered the atmosphere at 8 kilometers per second (18,000 miles per hour), and flew nominally, enduring the intended heat pulse that saw temperatures exceeding 1371˚C (2500˚F) on the front side while the payload skin remained only about 38˚C (100˚F). The RV exceeded Mach 30 and the heat-affected aeroshell withstood a pressure pulse that exerted 9g’s deceleration maintaining stable flight through the hypersonic, supersonic, transonic, and subsonic regimes to the parachute deployment. As part of the Agency’s strategic goal “to extend human presence deeper into space and to the moon for sustainable long-term exploration and utilization”, the LOFTID inflatable aerodynamic decelerator or aeroshell technology could one day help land humans on Mars. As with any flight test, data collection is of utmost importance. Without a data downlink and a possibility of the RV sinking before the recovery crew got to it, a secondary data collection method was introduced. The RV would eject a data recorder, which would have a duplicate copy of the on-board flight date, before splashdown and be retrieved separately. This paper discusses the development of the ejection mechanism used to eject the data recorder from the RV during the test flight. The development includes discussions of design constraints, a design overview, the testing program, and lessons learned throughout the process all the way through successful data recorder recovery.

mechanism↗

Combination of an electrolytic pretreatment unit with secondary water reclamation processes

The design and fabrication of a flight concept prototype electrolytic pretreatment unit (EPU) and of a contractor-furnished air evaporation unit (AEU) are described. The integrated EPU and AEU potable water recovery system is referred to as the Electrovap and is capable of processing the urine and flush water of a six-man crew. Results of a five-day performance verification test of the Electrovap system are presented and plans are included for the extended testing of the Electrovap to produce data applicable to the combination of electrolytic pretreatment with most final potable water recovery systems. Plans are also presented for a program to define the design requirements for combining the electrolytic pretreatment unit with a reverse osmosis final processing unit.

Wells, G. W.↗

Plasma Assisted Nutrient Recovery from Inedible Biomass via Ash Leaching

Sustaining a human presence on the Moon, Mars, or deep space will require closing loops on many life support systems. Some form of agriculture will be required because plants produce the vitamins, antioxidants, and essential oils in our diets that degrade over time in stored foods. In addition, they provide dietary fiber, revitalize air and purify water. It is estimated that 93 kg of plant nutrients are required to support one crew member per year. Growing plants will require recycling nutrients trapped in inedible plant stems, leaves and debris. We examined the effects of using thermal plasma and various carrier gases to breakdown inedible plant biomass and aid in nutrient recovery. Previous work demonstrated a thermally degrading environment such as a muffle furnace improved nutrient recovery from inedible biomass prior to an acid leaching process, however, a muffle furnace is an inefficient process. We tested the ability of a small scale, thermal plasma using carbon dioxide, nitrogen, or air as plasma carrier gases to degrade pelleted plant biomass. The gases were chosen to explore variations in recovery and potential chemical by-products. Plasma treated and untreated biomass was leached with different concentrations of acid to determine the extraction of nutrients (potassium, magnesium, calcium, and. phosphorus) for reuse in the crop production cycle. Results are presented showing the impact of plasma processing prior to acid leaching on recovery of plant nutrients.

Plasma↗

A 727 airplane center duct inlet low speed performance confirmation model test for refanned JT8D engines, phase 2

The results from testing of a 0.3 scale model center duct inlet (S duct) for the Pratt and Whitney Aircraft JT8D-100 engines are presented. The objective of this test was to demonstrate that the required airflow of the JT8D-100 engine (480 lb/sec as compared to 334 lb/sec for JT8D-15) can be achieved with minimum modifications to the existing 727 airplane structure at acceptable levels of total pressure recovery and distortion. Steady-state pressure recovery, steady-state pressure distortion, and dynamic pressure measurements were taken at the engine face station. Surface static pressure measurements were taken along the duct. Test results indicated that the required airflow was achieved with acceptable pressure recovery (comparable to the current 727-200 S duct). Inlet inflow angle variation within the 727 airplane operating regime (minus 5 to 5 degrees) had no effect on the inlet performance. Pressure distortion at static and forward speed at takeoff airflow conditions are within P and WA limits for the Phase II duct when equipped with vortex generators. Static crosswind operation between 10 knots and 25 knots appears feasible at full takeoff power.

Kaldschmidt, G.↗

Postural equilibrium following exposure to weightless space flight

Postural equilibrium performance by Skylab crewmen following exposure to weightlessness of 28, 59, and 84 days respectively was evaluated using a modified version of a quantitative ataxia test developed by Graybiel and Fregly (1966). Performance for this test was measured under two sets of conditions. In the first, the crewman was required to maintain postural equilibrium on narrow metal rails (or floor) with his eyes open. In the second condition, he attempted to balance with his eyes closed. A comparison of the preflight and postflight data indicated moderate postflight decrements in postural equilibrium in three of the crewmen during the eyes open test condition. In the eyes-closed condition, a considerable decrease in ability to maintain balance on the rails was observed postflight for all crewmen tested. The magnitude of the change was most pronounced during the first postflight test day. Improvement was slow; however, on the basis of data obtained, recovery of preflight baseline levels of performance was evidently complete at the end of approximately two weeks for all crewmen. The findings are explained in terms of functional alterations in the kinesthetic, touch, vestibular and neuromuscular sensory mechanisms induced by the prolonged absence of a normal 1-G gravitational environment.

Homick, J. L.↗

Development of the Aries parachute system

The design and testing of a two-stage parachute system to recover a space telescope weighing up to 2200 pounds is described. The system consists of a 15-ft diameter ribbon parachute reefed to 50 percent for 10 seconds and a 73-ft diameter paraform or cross second stage reefed to 20 percent for 10 seconds. The results of ten drop tests and two operational rocket launched flights are presented. Two successful operational recoveries of 1600-lb and 2050-lb NASA space telescopes were conducted at White Sands Missile Range, NM. The payloads are launched by ARIES rockets to altitudes of about 194 and 163 miles above sea level.

Pepper, W. B.↗

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet-pressure data were obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top-mounted twin inlets. Data are presented from wind tunnel tests conducted at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27-deg and angles of sideslip up to 12-deg. Trimmed aerodynamic characteristics and inlet performance were compared for three different leading-edge extension (LEX) configurations. The effects of wing leading- and trailing-edge flaps on the inlet were also determined. Maneuver performance was calculated from combined force and inlet-pressure data. The largest of the three LEX sizes tested gave the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗

Inlet and airframe compatibility for a V/STOL fighter/attack aircraft with top-mounted inlets

Aerodynamic force and inlet pressure data are obtained for 9.5% force and pressure models of a V/STOL fighter/attack aircraft configuration with top mounted twin inlets. Data are presented from tests conducted in the Ames Unitary Wind Tunnels at Mach numbers of 0.6, 0.9, and 1.2 at angles of attack up to 27 deg. and angles of sideslip up to 12 deg. Trimmed aerodynamic characteristics and inlet performance are compared for three different leading edge extension (LEX) configurations. The effects of wing leading and trailing-edge flaps on the inlet are also determined. Maneuver perfromance is calculated form combined force and inlet pressure data. The largest of the three LEX sizes tested gives the best airplane maneuver performance. Wing flap deflections improved inlet recovery at all Mach numbers.

Durston, D. A.↗

T/R switch design for short-range measurements, part 6.1A

The positive intrinsic negative (PIN) diode switch which is designed to protect the receiver from burnout or damage on transmission and channel the echo signal to the receiver on reception is outlined. The receiver must be protected firmly. A schematic diagram of a transformer rectifier (TR-ATR) switch for the Urbana Radar is shown. The T/R switch consists of a half wavelength coaxial cavity with tuning condenser and PIN diodes. Two UM4300 PIN diodes were mounted between the inner and outer conductor. The dc biasing voltage required for the PIN diodes is supplied by a control circuit. On transmission, the PIN diodes are forward biased to about 0.5 amperes. On reception, about 10 volts reverse voltage is applied to the diodes, which produces an initial reverse current to speed the recovery time. The T/R switch characteristics are estimated and the result of testing at different peak transmitter powers from 410 kW to 1500 kW is shown.

Yu, B.↗

Summary of NASA stall/spin research for general aviation configurations

The major milestones of stall/spin research conducted in the past under NACA/NASA programs are reviewed, and recent results offering promise for further improvements in design methodology and concepts for stall/spin technology are identified. Specific results discussed include: (1) development and validation of test techniques and analysis methods; (2) studies of airplane spinning and spin recovery characteristics; and (3) concepts designed to increase the spin resistance of general aviation-type vehicles.

Chambers, J. R.↗

Preliminary experimental results of gas recycling subsystems except carbon dioxide concentration

Oxygen concentration and separation is an essential factor for air recycling in a controlled ecological life support system (CELSS). Furthermore, if the value of the plant assimilatory quotient is not coincident with that of the animal respiratory quotient, the recovery of oxygen from the concentrated CO2 through chemical methods will become necessary to balance the gas contents in a CELSS. Therefore, oxygen concentration and separation equipment using Salcomine and O2 recovery equipment, such as Sabatier and Bosch reactors, were experimentally developed and tested.

Otsuji, K.↗

TEXSYS - A large scale demonstration of model-based real-time control of a Space Station subsystem

A hybrid approach to qualitative and temporal reasoning, using a device-oriented model-based representation in conjunction with both consistency-based and classification diagnosis methods, can be effectively used to monitor and control a complex electromechanical system. An example of this approach is given in some recent tests of the Thermal Expert System (TEXSYS) in control of the Boeing Aerospace Thermal Bus System (BATBS), a prototype two-phase Space Station Freedom thermal bus. The constraints of realtime performance and changing target hardware led to significant changes in the initial approach, including a reduction in the use of deep structural reasoning and the addition of temporal reasoning capabilities. TEXSYS test results show the successful completion of both nominal control and fault recovery actions with the BATBS.

Glass, B. J.↗

Microgravity effects on standardized cognitive performance measures

The purpose of this experiment, selected to fly on the International Microgravity Laboratory (IML-2) Spacelab mission, is to determine the effects of microgravity upon the cognitive skills which are critical to successful performance of many tasks on board the Space Shuttle. Six tests from the Unified Tri-service Cognitive Performance Assessment Battery (UTC-PAB) will be administered to the Mission Specialists to fulfill the goals of this experiment. These tests are based upon current theoretical models of human performance and the hypothesized effects of microgravity. The principle objective is the identification of the effects of microgravity upon specific information processing skills affecting performance from those of fatigue and shifts in work/rest cycles. Multiple measures of both short and long term fatigue will be obtained and used as a major independent variable for the analysis of these performance data. Scientific supporting studies will determine optimum practice and performance testing schedules for the astronauts. The same tests will be used post-flight to collect data on the recovery of any cognitive performance impairment compared with pre-flight, baseline levels.

Schiflett, Samuel G.↗

Installed F/A-18 inlet flow calculations at 60 deg angle-of-attack and 10 deg side slip

This paper presents the results of PARC3D numerical calculations on a 19.78 percent scale forebody/inlet model of the F/A-18 at a Mach number of 0.20, an angle-of-attack of 60 deg, and a side-slip angle of 10 deg. The main purpose of these calculations is to support an upcoming wind-tunnel test program in the prediction of engine inlet compressor face total pressure recovery and flow distortion. The GRIDGEN system was used to generate a grid which includes the inlet and lip, and other aircraft components which are considered to be important to inlet performance, such as the ramp/splitter plate, the diverter and slot, and the deflected leading edge flap. PARC3D shows complex flow patterns on the fuselage surfaces below the leading edge extensions, on the ramp/splitter plate, inlet lip, and inside the inlet. PARC3D tends to underpredict total pressure recovery and overpredict the flow distortion at the inlet compressor face.

Podleski, S. D.↗