Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CALCULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

GAMMA-RAY BURST REVERSE SHOCK EMISSION IN EARLY RADIO AFTERGLOWS

Reverse shock (RS) emission from gamma-ray bursts is an important tool in investigating the nature of the ejecta from the central engine. If the magnetization of the ejecta is not high enough to suppress the RS, a strong RS emission component, usually peaking in the optical/IR band early on, would provide an important contribution to early afterglow light curve. In the radio band, synchrotron self-absorption may suppress early RS emission and also delay the RS peak time. In this paper, we calculate the self-absorbed RS emission in the radio band under different dynamical conditions. In particular, we stress that the RS radio emission is subject to self-absorption in both RSs and forward shocks (FSs). We calculate the ratio between the RS to FS flux at the RS peak time for different frequencies, which is a measure of the detectability of the RS emission component. We then constrain the range of physical parameters for a detectable RS, in particular the role of magnetization. We notice that unlike optical RS emission which is enhanced by moderate magnetization, moderately magnetized ejecta do not necessarily produce a brighter radio RS due to the self-absorption effect. For typical parameters, the RS emission component would not be detectable below 1 GHz unless the medium density is very low (e.g., n < 10{sup −3} cm{sup −3} for the interstellar medium and A {sub *} < 5 × 10{sup −4} for wind). These predictions can be tested using the afterglow observations from current and upcoming radio facilities such as the Karl G. Jansky Very Large Array, the Low-Frequency Array, the Five Hundred Meter Aperture Spherical Telescope, and the Square Kilometer Array.

79 ASTRONOMY AND ASTROPHYSICS↗

Birefringence axis rotation and nonlinear response of a side-hole fiber pressure sensor

The pressure-induced birefringence of side-hole fibers has been widely explored for hydrostatic pressure measurement. Here, this paper studies the effects of the initial birefringence of a side-hole fiber on the pressure response of polarimetric sensors based on side-hole fibers. A mathematical model, where the stress field induced by the pressure is assumed to be uniform in the core region of the fiber, was established to calculate the birefringence and optical axis rotation as a function of the differences between the two principal stress components of the stress field in the core region. Simulation results show that when there is misalignment between the initial birefringence axes and the principal axes of the stress field, pressure changes cause rotations of the birefringence axis, leading to complicated and nonlinear changes of birefringence as a function of pressure. Experiments were conducted using fiber-Bragg-grating-based resonators on side-hole fibers with different initial birefringence, and the results agree well with the simulation. The results underscore the importance of the control of magnitude and direction of the initial birefringence of the side-hole fiber and provide guidelines for the design and fabrication of side-hole fiber pressure sensors.

42 ENGINEERING↗

Pack-boriding of Fe-Mn binary alloys: Characterization and kinetics of the boride layers

In this work, the boronizing of Fe-Mn binary alloys at 0.42, 0.76 and 0.94 wt.% Mn was carried out in a solid medium using the powder pack method. In this method, commercial Ekabor-II boron source and activator (ferro-silicon) were thoroughly mixed to form the boriding medium. The samples were boronized in an electrical resistance furnace for exposure times of 2, 4, 6 and 8 h at 1173 K under atmospheric pressure and a series of boronized samples in the temperature range 1073-1373 K for 3 h. After the furnace process, boronized samples were removed from the furnace and cooled in air. Afterwards, the boride layers generated by the pack-boronizing process were characterized by optical microscopy, scanning electron microscopy, XRD analysis, Vickers microhardness and tensile testing. The generated boride layers, showing a saw-tooth morphology, had a surface microhardness in the range 1400-1270 HV0.1. It was shown that the values of yield stresses and ultimate tensile stresses were increased as the Mn content increases in the boronized Fe-Mn binary alloys. In contrast, the values of elongations determined from the stress-strain curves were decreased. Furthermore, it was found that the calculated mean value of the activation energy of boron diffusion was close to 119 J/mol.

36 MATERIALS SCIENCE↗

Coexistence pressure for a martensitic transformation from theory and experiment: Revisiting the bcc-hcp transition of iron under pressure

We revisit results from decades of pressure experiments on the bcc ↔ hcp transformations in iron, which are sensitive to non-hydrostatic conditions and sample size. We emphasize the role of martensitic stress in the observed pressure hysteresis and address the large spread in values for onset pressures of the nucleating phase. From electronic-structure calculations, we find a bcc ↔ hcp equilibrium coexistence pressure of 8.4 GPa. Accounting for non-hydrostatic martensitic stress and a stress-dependent transition barrier, we suggest a pressure inequality for better comparison to experiment and observed hysteresis. We construct the equation of state for bcc and hcp phases under hydrostatic pressure, and compare to experiments and previous calculations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Non-iterative characteristics analysis for high-pressure ramp loading

Here in the canonical ramp compression experiment, a smoothly increasing load is applied to the surface of the sample, and the particle velocity history is measured at two or more different distances into the sample, at interfaces where the surface of the sample can be probed. The velocity histories are used to deduce a stress-density relation, usually using iterative Lagrangian analysis to account for the perturbing effect of the impedance mismatch at the interface. In that technique, a stress-density relation is assumed in order to correct for the perturbation and is adjusted until it becomes consistent with the deduced stress-density relation. This process is subject to the usual difficulties of nonlinear optimization, such as the existence of local minima (sensitivity to the initial guess), possible failure to converge, and relatively large computational effort. We show that, by considering the interaction of successive characteristics reaching a free surface, the stress-density relation can be deduced directly by recursion rather than iteration. This calculation is orders of magnitude faster than iterative analysis and does not require an initial guess. Direct recursion may be less suitable for very noisy data, but it was robust when applied to trial data. The stress-density relation deduced was identical to the result from iterative Lagrangian analysis.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On the use of adjoints in the inversion of observed quasi-static deformation

An adjoint-based conjugate gradient algorithm provides an efficient means for imaging sources of deformation within the Earth, such as volume stresses associated with fluid flow in aquifers and reservoirs. For time intervals over which the overburden deforms elastically, one can calculate the gradient elements for a single model update using just two numerical simulations. The first is a forward run that is used to compute the residuals associated with the given iteration. The second simulation is to evaluate the application of the adjoint operator to the residuals. In this adjoint calculation, the residual displacements are applied as sources at the measurement locations, driving the deformation in the simulation. The volume stress on the source grid blocks, in response to the residual displacements, provide the gradient components. We apply this technique to satellite-based interferometric synthetic aperture radar (InSAR) line-of-sight displacements that were observed over an oil reservoir in California’s Central Valley. Furthermore, we find that the adjoint-based gradient estimates, requiring 18 CPU seconds, agree with conventional numerical calculations that take over 3700 CPU seconds to compute. Conjugate gradient algorithms utilizing the conventional approach and adjoint-based gradient computations give roughly the same reductions in misfit and similar final estimates of reservoir volume change.

58 GEOSCIENCES↗

In-situ neutron diffraction study of phase stress evolutions in a Ni-basedporous anode under uniaxial load

Ni/YSZ porous composite is used widely as anode for solid oxide fuel cells. In this study, neutron diffraction patterns were recorded in-situ while a bulk porous Ni-NiO-YSZ anode was loaded under uniaxial compression. Single peak refinement was used to calculate the lattice strains of each phase in the composite, and the local stress state of each phase was derived from the measured lattice strains and the corresponding diffraction elastic constants. An internal triaxial stress state was observed to develop in the bulk of the specimen under plastic deformation, specifically in the Ni phase. Meanwhile, the NiO and YSZ phases are deforming elastically even in the macroscopically plastic regime of deformation. The von Mises equivalent stress was used to quantify the phase stress evolution. A significant stress concentration induced by the presence of pores becomes manifest in all three phase components. The reduction of stress concentration factor in Ni above the yield point of the composite can be attributed to a gradual change of the grains-pores morphology during the plastic deformation.

30 DIRECT ENERGY CONVERSION↗

Vacancy-mediated transport and segregation tendencies of solutes in FCC Ni under diffusional creep

Nickel-based alloys are known for their excellent corrosion resistance and high-temperature strength. However, at high temperatures, polycrystals experience grain boundary-stress-driven vacancy diffusion leading to diffusion-driven creep. Understanding the fundamentals of defect migration is essential to predict diffusion creep behavior. In this talk, we explore the Nabarro-Herring diffusion creep and the associated solute segregation that is likely to result from the different diffusivities of the solute and solvent elements. Density functional theory calculations are performed to determine the formation, migration and binding energies of the solute and vacancy defects in stress-free and stressed states. The dilute-limit transport coefficients are then calculated using the self-consistent mean field theory as implemented in the Kinetic Cluster Expansion (KineCluE) code. Predictions of diffusion creep strain rates and solute segregation are then presented for various solutes, stress and temperatures. This work opens research avenues for exploration of diffusion creep via characterization of elemental segregation to grain boundaries.

36 MATERIALS SCIENCE↗

A study of various geometries of gold nanowires and effect of doping

We present here the simulations, using Gupta Potential, of gold cylinders under stress, showing the changes leading to the formation of chains at nano level. When one of these short chains is stretched, it transforms from a zigzag configuration to a straight one, passing through various qualitatively different phases and ultimately disintegrating via an interesting ‘dimer’ phase. Strain vs stress for all the cases are presented and young’s modulus calculated. Using Density functional theory (DFT) study we have shown that doping of gold strand with Silicon or Carbon atoms increases its thermodynamic stability as suggested in a recent study.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Compressibility and strength of nanocrystalline tungsten boride under compression to 60 GPa

The compression behavior and stress state of nanocrystalline tungsten boride (WB) were investigated using radial x-ray diffraction (RXRD) in a diamond-anvil cell under non-hydrostatic compression up to 60.4 GPa. The compression properties and stress state are analyzed using lattice strain theory. Experiments were conducted at beamline X17C of the National Synchrotron Light Source. The radial x-ray diffraction data yield a bulk modulus that is qualitatively consistent with density functional theory calculations and demonstrate that WB is a highly incompressible material. A maximum differential stress, t, of about 14 GPa can be supported by nanocrystalline WB at the highest pressure. This corresponds to about 5% of the shear modulus, G, which is smaller than the values of t/G ({approx}8%-10%) observed for BC{sub 2}N, B{sub 6}O, TiB{sub 2}, and {gamma}-Si{sub 3}N{sub 4} at high pressures. Thus, while WB is highly incompressible, its strength is relatively low at high pressures compared to other hard ceramics.

36 MATERIALS SCIENCE↗

Theory of Intermittent Cutting. 5. Description of Tool Entry in the Blank

Vorontsov’s plastic-flow method permits the derivation of a model of cutting for the region where the tool enters the blank. The stress–strain state of the blank is determined, and the dimensions of the plasticdeformation zone are calculated. The main cutting parameters are shown to be variable.

42 ENGINEERING↗

Stress-induced anomalous shift of optical band gap in Ga-doped ZnO thin films: Experimental and first-principles study

In this work, highly c-axis oriented Ga-doped ZnO thin films have been deposited on glass substrates by RF magnetron sputtering under different sputtering times. The optical band gap is observed to shift linearly with the electron concentration and in-plane stress. The failure of fitting the shift of band gap as a function of electron concentration using the available theoretical models suggests the in-plane stress, instead of the electron concentration, be regarded as the dominant cause to this anomalous redshift of the optical band gap. And the mechanism of stress-dependent optical band gap is supported by the first-principles calculation based on density functional theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fabric evolution and dilatancy within anisotropic critical state theory guided and validated by DEM

Fabric, expressed by means of an evolving deviatoric fabric tensor F, plays a very important role in the anisotropic mechanical response of granular materials. The Anisotropic Critical State Theory (ACST) addresses fabric anisotropy by rendering dilatancy a function of F, in addition to other state variables. In this paper, 3D DEM is used to guide the specific grain-level definition of F, the formulation of its continuum evolution equation and its effect on anisotropic dilatancy within ACST. DEM provides stress-ratio and shear strain variations as input for ACST analytical calculations of evolving fabric tensor and dilatancy, which are then favourably compared with totally independent direct measurements of these quantities by DEM. Furthermore, dilatancy is shown to be strongly affected by the contact normal-based fabric tensor Fc, whose evolution is best described by a continuum equation within ACST that includes dilatancy and a quantity related to particle orientation-based fabric tensor Fp. The aforementioned favourable comparison of the results for fabric tensor and dilatancy obtained independently by ACST and DEM, confirms the validity of the core framework of ACST irrespective of any constitutive model that addresses the deviatoric stress-strain relations.

58 GEOSCIENCES↗

Sound velocities in highly oriented pyrolytic graphite shocked to 18 GPa: Orientational order dependence and elastic instability

Previous reports of rapid phase transformation above 18 GPa [Erskine and Nellis, Nature 349, 317 (1991)] and large elastic waves below 18 GPa [Lucas et al., J. Appl. Phys. 114, 093515 (2013)] for shock-compressed ZYB-grade highly-oriented pyrolytic graphite (HOPG), but not for less oriented ZYH-grade HOPG, indicated a link between the orientational order dependence of the HOPG response above and below the phase transformation stress. To gain insight into this link and into the mechanical response of HOPG shocked to peak stresses approaching the phase transformation onset, the compressibility of ZYB- and ZYH-grade HOPG in the shocked state was examined using front surface impact experiments. Particle velocity histories and sound velocities were measured for peak stresses reaching 18 GPa. Although the locus of the measured peak stress-particle velocity states is indistinguishable for the two grades of HOPG, the measured sound velocities in the peak state reveal significant differences between the two grades. Specifically, 1) The measured sound velocities are somewhat higher for ZYH-grade HOPG, compared to ZYB-grade HOPG. 2) The measured sound velocities for ZYH-grade HOPG increase smoothly with compression, whereas those for ZYB-2 grade HOPG exhibit a significant reduction in the compression dependence from 12 GPa to 17 GPa and an abrupt increase from 17 GPa to 18 GPa. 3) The longitudinal moduli, determined from the measured sound velocities, are smaller than the calculated bulk moduli for ZYB-grade HOPG shocked to peak stresses above 15 GPa, indicating the onset of an elastic instability. The present findings demonstrate that the softening of the longitudinal modulus (or elastic instability) presented here is linked to the large elastic waves and the rapid phase transformation reported previously – all observed only for shocked ZYB-grade HOPG. The elastic instability in shocked ZYB-grade HOPG is likely a precursor to the rapid phase transformation observed above 18 GPa for this HOPG grade.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Deformation Behaviors in Single BCC‐Phase Refractory Multi‐Principal Element Alloys under Dynamic Conditions

The mechanical behavior and microstructural evolution of a BCC-phase NbTaTiV refractory multi-principal element alloy (RMPEA) is studied over a wide range of strain rates (10 −3 to 10 3 s −1 ) and temperatures (room temperature to 850 °C). The mechanical property of present RMPEA shows less strain-rate dependence and strong resistance to softening at high temperatures. Under high strain-rate loading, the formation of thin type-I twins is observed, which could lead to an increase in strain-hardening rates. However, this hardening mechanism competes with adiabatic heating effects, resulting in the deterrence of strain-hardening behaviors. In contrast, substantial strain-hardening occurs at cryogenic temperatures due to the formation of twins, which act as stronger barriers to dislocation motion and interact with each other. To further understand the different strain-hardening behaviors, density functional theory (DFT) calculations predict relatively low stacking fault energies and high twinning stress for the NbTaTiV RMPEA.

36 MATERIALS SCIENCE↗

Analysis of the Stress State of Hollow Cylinders with Concave Corrugated Cross Sections

In the three-dimensional statement, by the method of approximation of functions by discrete Fourier series, we perform the analysis of the dependence of the stress state of a hollow cylinder whose cross section has the form of joined concave semicorrugations subjected to the action of internal pressure under certain conditions imposed on the end faces on the thicknesses and curvatures of the cross sections of the cylinders caused by the changes in the number of semicorrugations. The results of the solution of the problem are presented in the form of the plots of distributions of the fields of displacements and stresses.

97 MATHEMATICS AND COMPUTING↗

Effects of Particle Diameter and Coke Layer Thickness on Solid Flow and Stress Distribution in BF by 3D Discrete Element Method

In order to reduce ironmaking-related CO{sub 2} emissions, hydrogen-enriched blast furnace (BF) operation is currently under development. In hydrogen-enriched BF operation, coke layer thickness can be decreased to reduce CO{sub 2} emissions. However, BFs operating with thin coke layers may experience instability or discontinuous phenomena such as particle slip and gas channeling problems, so it is important to optimize the particle diameter and coke layer thickness for optimal BF operation. In this study, the effects of particle diameter and coke layer thickness on the solid flow and stress distribution in a BF were analyzed using a three-dimensional discrete element method. Furthermore, the effects of particle diameter and coke layer thickness on the burden layer stabilities, particle velocities, and particle stress distributions have been investigated. The results show that decreasing the coke layer thickness caused instability owing to the mixing of the coke and ore layers in the BF-cohesive zone and slight increases in both the average particle velocities and the average normal particle stress magnitudes. In addition, the average particle velocities and average normal particle stresses were higher for the smaller particles than for the larger ones during the simulations.

36 MATERIALS SCIENCE↗

Three dimensional microstructural characterization of nanoscale precipitates in AA7075-T651 by focused ion beam (FIB) tomography

The size and distribution of precipitates in Al 7075 alloys affects both the mechanical and corrosion behavior (including stress corrosion cracking and fatigue corrosion) of the alloy. Three dimensional (3D) quantitative microstructural analysis of Al 7075 in the peak aged condition (T651) allows for a better understanding of these behaviors. In this study, Focused ion beam (FIB) tomography was used to characterize the microstructure in three dimensions. Analysis of grains and precipitates was performed in terms of volume, size, and morphology. It was found that the precipitates at the grain boundaries are larger in size, higher in aspect ratios and maximum Feret diameter compared to the precipitates inside the grains, due to earlier nucleation of the precipitates at the grain boundaries. Our data on the precipitates at the interface between grains and Mg{sub 2}Si inclusion show that the surfaces of inclusion (impurity) particles can serve as a location for heterogeneous nucleation of precipitates. - Highlights: •Focused ion beam (FIB) tomography was used to characterize the microstructure of Al 7075 in three dimensions. •Analysis of grains and precipitates was performed in terms of volume, size, and morphology. •Precipitates at the grain boundaries have larger size and aspect ratio compared to the precipitates inside the grains.

36 MATERIALS SCIENCE↗