Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test Reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Decommissioning the physics laboratory, building 777-10A, at the Savannah River Site (SRS)

SRS recently completed a four year mission to decommission {approx}250 excess facilities. As part of that effort, SRS decommissioned a 48,000 ft{sup 2} laboratory that housed four low-power test reactors, formerly used by SRS to determine reactor physics. This paper describes and reviews the decommissioning, with a focus on component segmentation and handling (i.e. hazardous material removal, demolition, and waste handling). The paper is intended to be a resource for engineers, planners, and project managers, who face similar decommissioning challenges. Building 777-10A, located at the south end of SRS's A/M-Area, was built in 1953 and had a gross area of {approx}48,000 ft{sup 2}. Building 777-10A had two main areas: a west wing, which housed four experimental reactors and associated equipment; and an east wing, which housed laboratories, and shops, offices. The reactors were located in two separate areas: one area housed the Process Development Pile (PDP) reactor and the Lattice Test Reactor (LTR), while the second area housed the Standard Pile (SP) and the Sub-critical Experiment (SE) reactors. The west wing had five levels: three below and three above grade (floor elevations of -37', -28', -15', 0', +13'/+16' and +27' (roof elevation of +62')), while the east wing had two levels: one below and one above grade (floor elevations of -15' and 0' (roof elevation of +16')). Below-grade exterior walls were constructed of reinforced concrete, {approx}1' thick. In general, above-grade exterior walls were steel frames covered by insulation and corrugated, asbestos-cement board. The two interior walls around the PDP/LTR were reinforced concrete {approx}5' thick and {approx}30' high, while the SP/SE reactors resided in a reinforced, concrete cell with 3.5'-6' thick walls/roof. All other interior walls were constructed of metal studs covered with either asbestos-cement or gypsum board. In general, the floors were constructed of reinforced concrete on cast-in-place concrete beams below-grade and concrete on metal beams above-grade. The roofs were flat concrete slabs on metal beams. Building 777-10A was an important SRS research and development location. The reactors helped determine safe operational limits and loading patterns for fuel used in the SRS production reactors, and supported various low power reactor physics studies. All four reactors were shut down and de-inventoried in the 1970's. The building was DD and R 2007, Chattanooga, Tennessee, September 16-19, 2007 169 subsequently used by various SRS organizations for office space, audio/visual studio, and computer network hub. SRS successfully decommissioned Building 777-10A over a thirty month period at a cost of {approx}$14 M ({approx}$290/ft{sup 2}). The decommissioning was a complex and difficult effort due to the building's radiological contamination, height, extensive basement, and thick concrete walls. Extensive planning and extensive hazard analysis (e.g. of structural loads/modifications leading to unplanned collapse) ensured the decommissioning was completed safely and without incident. The decommissioning met contract standards for residual contamination and physical/chemical hazards, and was the last in a series of decommissioning projects that prepared the lower A/M-Area for SRS's environmental restoration program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal Analysis of Irradiation Experiments in the ATR

Reactor material testing in the INL's Advanced Test Reactor (ATR) involves modeling and simulation of each experiment to accurately determine the irradiation temperature. This paper describes thermal analysis of capsule experiments using gas gap temperature control and provides data on recent material tests that validate the modeling results. Static capsule experiments and lead-out capsule experiments are discussed. The source of temperature variation in capsule experiments and ways to mitigate these variations are also explained. Two examples of instrumented lead-out capsule experiments, TMIST-1 and UCSB-2, are presented. A comparison of measured and calculated temperatures is used to validate the thermal models and to ascertain the accuracy of the calculated temperature.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A Revised Capsule Design for the Accelerated Testing of Advanced Reactor Fuels

The Advanced Test Reactor (ATR) has been used successfully for the testing of fast reactor fuel for nearly two decades. These successes have been in spite of numerous challenges for testing fast reactor fuel in the ATR (a thermal spectrum reactor), but the solutions to those challenges have resulted in excessively long irradiation times (~10 years) for high-burnup targets as well as experiments that are highly sensitive to fabrication tolerances and eccentricities. This paper presents a solution to the problems of extended irradiation times and fabrication sensitivities. Thermal and neutronic analyses were performed to show that a reduced-diameter fuel pin with an equivalent linear heat generation rate can provide a prototypic thermal profile (peak centerline and inner clad temperature) along with a near-prototypic power profile within the ATR thermal spectrum. This allows the experiment to reach a high burnup in an expeditious timeframe compared to traditional ATR fast fuel irradiations. In addition, problems with fabrication sensitivities were addressed by introducing a double-encapsulated experiment that pushes the high heat flux helium gap farther away from the fuel pin. Fuel pin position eccentricities are also mitigated by using a large sodium bond between the pin and capsule fuel. The advantages and potential pitfalls of this revised design are discussed, including the effect of length scales on fuel system behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of fluence-rate determination techniques for the Advanced Test Reactor-Critical Facility

A technique using small, enriched uranium-aluminum alloy monitors to measure fission rates in fuel plate assembly reactors was developed at the Idaho National Laboratory Radiation Measurements Laboratory in support of Advanced Test Reactor Critical (ATR-C) Facility irradiations. Previous measurements were performed to determine the correlation between the beta-particle activity and the fission rate in the U-Al monitors following irradiation. The American Society for Testing and Materials (ASTM) has established a standard practice E704 for determining neutron fluence rate by radioactivation of depleted uranium by measuring the concentration of fission-products in irradiated uranium monitors. Rather than measuring the beta-particle decay from fission-products, the decay rate of fission-products is determined by gamma-ray spectroscopy. The feasibility of using a method adapted from the ASTM standard practice E704 was investigated for ATR-C irradiations and compared to the present method by analyzing a subset of 21 monitor wires using both methods. The resulting calculated fission rates agreed with an average standard deviation of 7.45%, within the average combined measurement error of 9.05%. Practical considerations such as expected fluence-rates, sample activity, and counting-time were compared between the two methods and the sources of error for each method were investigated. Quality assurance measurements utilizing the modified ASTM standard method are recommended for future test irradiation, but gross-beta-particle counting remains the most practical solution for ATR-C fluence-rate determination.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

SAS4A/SASSYS-1 Verification Testing for Sodium Fast Reactor Applications: Acceptance Testing Report

SAS4A/SASSYS-1 (SAS) is a simulation tool used to perform deterministic analyses of anticipated events as well as design basis and beyond design basis accidents for advanced liquid-metal-cooled nuclear reactors. With its origin as SAS1A in the late 1960s, the SAS series of codes has been under continuous use and development for over forty-five years and represents a critical investment in safety analysis capabilities for the U.S. Department of Energy. To support demonstration of software pedigree and confirm key functional requirements, this report has been generated to provide detailed verification of the software. Although SAS was developed to support the analysis of any liquid-metal-cooled nuclear reactor, the acceptance testing described in this document focuses on the verification of SAS capabilities as they relate to pool-type Sodium Fast Reactors (SFRs). This report includes documentation of the test problem definition, analytical solution(s), computational solution(s), acceptance criteria, comparisons of analytical/computational solutions, and determination of acceptance of the computational solution(s). Deviations from acceptance criteria are noted.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SAS4A/SASSYS-1 Verification Testing for Sodium Fast Reactor Applications (Acceptance Testing Report)

SAS4A/SASSYS-1 (SAS) is a simulation tool used to perform deterministic analyses of anticipated events as well as design basis and beyond design basis accidents for advanced liquid-metal- cooled nuclear reactors. With its origin as SAS1A in the late 1960s, the SAS series of codes has been under continuous use and development for over fifty years and represents a critical investment in safety analysis capabilities for the U.S. Department of Energy. To support demonstration of software pedigree and confirm key functional requirements, this report has been generated to provide detailed verification of the software. Although SAS was developed to support the analysis of any liquid-metal-cooled nuclear reactor, the acceptance testing described in this document focuses on the verification of SAS capabilities as they relate to pool-type Sodium Fast Reactors (SFRs). This report includes documentation of the test problem definition, analytical solution(s), computational solution(s), acceptance criteria, comparisons of analytical/computational solutions, and determination of acceptance of the computational solution(s). Deviations from acceptance criteria are noted.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The Impact of Furnace-Testing on the Microstructure of an Irradiated U-Mo Fuel Plate

The Material Management and Minimization Program (formerly known as the Reduced Enrichment for Research and Test Reactor Program) is responsible for converting research reactors that use highly enriched uranium (HEU) fuels to ones that use low-enriched uranium (LEU) fuels. As part of the development of LEU fuels, a variety of irradiation experiments are being conducted using the Advanced Test Reactor. In addition to the reactor tests, there is interest in generating information about the transient behavior of irradiated fuel plates. For example, it is of interest to determine the temperature at which a blister will form on the surface of a fuel plate, due to fission gas release from the fuel meat, for a particular fuel plate design. Since in-pile testing to determine the 'blister threshold' (the temperature where a blister forms on the surface of a fuel plate) in plate-type fuel is very difficult and expensive and has historically been deemed impractical for fuel qualification testing, an out-of-pile 'blister test' has been developed and employed. This post-irradiation blister anneal test was developed as a conservative simulation of in-pile behavior and has been routinely used for many research reactor fuel designs currently in use. In this test, the irradiated fuel plate is inserted into a furnace at a given temperature, soaked for a period of time, and removed for inspection. If no visible blisters appear, the furnace temperature is increased, and the plate is soaked and inspected again. This process continues until blisters are observed. Recently, a section from an irradiated U-7Mo dispersion fuel plate with Al-4043 matrix, which has a nominal composition of 4.81Si-0.20Fe-0.14Ti-0.16Cu-0.01Cr 0.01Mn-bal Al, was tested in a furnace located in the Hot Fuel Examination Facility, located at the Idaho National Laboratory, up to 500 deg. C, at which point blisters were observed on the surface of the fuel plate section. A sample near the blistered region of the fuel plate section was then characterized using scanning electron (SEM) and transmission electron microscopy (TEM). This paper discusses the results of this characterization and how they compare to those generated for a similar sample characterized after fabrication but before irradiation and for a sample characterized after irradiation but before furnace testing. One goal of this work is to identify the changes in the microstructure during blister testing that contribute to the eventual release of fission gas that results in the development of blisters. SEM analysis of the furnace-tested sample showed that in some locations of the U-7Mo particles, Al-4043 matrix constituents (primarily Si) had penetrated the microstructure along grain boundaries. This provided potential pathways for increased fission gas migration in the fuel meat microstructure during the furnace heating process. Some attack of these boundaries was also observed in the as-fabricated U-7Mo/Al-4043 sample, but there appeared to be additional attack during the furnace annealing. Besides the changes observed in grain boundary features, the TEM analysis showed that the fission gas bubbles that are typically present in the intra-granular regions of the as-irradiated U-7Mo microstructure as a fission gas bubble superlattice had changed in size, morphology, and distribution. The result of this may be an increase in the mobility of the fission gas in intra-granular regions of the fuel. The complete implications of the changes in fission gas morphology and distribution in the fuel meat microstructure and their impact on blistering continues to be investigated. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Scaling Analysis of Vortex Shedding Frequency between In line Plates

The Global Threat Reduction initiative (GTRI) was established by the National Nuclear Security Administration (NNSA) in 2004. One of the highlights of the program is to convert research and test reactors at home and abroad from Highly Enriched Uranium (HEU) to Low Enriched Uranium (LEU) fuels. By switching directly from HEU to LEU, an LEU reactor produces fewer neutrons than an HEU reactor and in some cases; a direct switch from HEU to LEU results in the reactor being unable to achieve criticality. Under certain circumstances, criticality is achieved and the original neutron fluxes are restored with LEU fuel by adding more fuel elements to the core. Not all reactors, exemplified by the Advanced Test Reactor (ATR) at the Idaho National Lab (INL), have the luxury of simply adding more fuel to the core. In such cases, entirely new designs must be created and tested. The ATR utilizes plate type fuel. During the design and testing of the ATR fuel, vortex shedding was identified as potential source for experiment and fuel failure. For fuel conversion, elements must be tested in pile prior to the qualification of the new fuel design. For some test elements, the primary test plate is followed by a secondary handling plate. It is known that objects downstream influence the vortex shedding. While vortex shedding is an important and well-studied phenomenon, not only in the context of nuclear engineering, but in fields as diverse as aeronautical engineering and biology, there is a significant gap in the understanding of vortex shedding in regards to two bluff bodies in line direct line with one another. The study provides a scaling analysis of the frequency of vortex shedding for plates in line. The scaling analysis is then compared to numerical simulation of two in line plates. The study provided a scaling analysis and suggested parameter for determining the expected trends in the Strouhal number for a plate with some object downstream. The analysis made the consideration of differing length scales as the cause for a reduction in vortex shedding frequency as well as looked at the potential impact of boundary layer growth on vortex shedding for a flat plate. The comparison between the expected scaling and numerical data was less than ideal, but there are several potential causes. One of the biggest issues with the comparison is the uncertainty associated with the defect velocity. The frequency was well established in several cases, but the velocity was not always well established resulting in a larger uncertainty. In the cases where the velocity was near zero (i.e. b/d = 0.5), the uncertainty dominated since the corrected Strouhal number is divided by the defect velocity. The Reynolds numbers were not incredibly large, ranging from 350-1600. The low Reynolds numbers potentially undermine the principle assumption made in the scaling analysis, i.e. Reynolds number is negligibly small. Additionally, the exact definition of the 'reduced velocity' was never explicitly defined, merely inferred from the assumption that the x length scale and y length scale were in fact different. Another potential problem is the defect velocities in the lower Reynolds number cases were not much smaller than the free stream velocity. Further work needs to be done at higher Reynolds numbers and with more data points to ensure the assumptions made are valid as well as confirm the accuracy of the scaled relationship. (authors)

42 ENGINEERING↗

Further work on credible levels of water moderation - 14267

The Research and Test Reactor (RTR) manufacturing operation produces aluminum clad fuel plates that are assembled into 'box type' elements that are used in reactors like the Advanced Test Reactor, University of Missouri, and Massachusetts Institute of Technology. These fuel plates and elements are stored in both horizontal and vertical arrangements during the manufacturing process. Since the presence of water is so important to criticality safety of the operations, a study was undertaken to establish credible levels of water moderation. At the NCSD 2013 Topical meeting, credible levels of interspersed water moderation from multiple sources including firefighting, steam and rain were presented. This covered the initial portions of the research. Subsequent research was conducted on water films resulting from these water sources. This phase of the research involved the formation of water films. These can form from condensation, water sprays or immersion. The thickness of the water films from these sources ranged from 0.04 cm to 0.30 cm for vertical fuel plates. Studies were also conducted on horizontal plates, stacks of plates and assembled elements. For fuel plates, the films ranged from essentially zero for stacked plates to 0.25 cm. For an element, there was sufficient adhesion that all of the channels were filled. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Graphite Moderation in Fast Reactors

With the renewed interest in designing and building a fast test reactor in the U.S., several new reactor concepts have been emerging. Although the main mission of a fast test reactor would be to enable high fast flux irradiation capability, there could be added value for such a fast test reactor to also offer thermal neutron irradiation capabilities. As such, several of these concepts considered the use of a moderator material in a Sodium-cooled Fast Reactor (SFR), which is claimed to also offer benefits with respect of mass of fuel required. The work discussed in this paper focuses on exploring and assessing the benefits and challenges resulting from making use of thermalized neutrons to reduce the critical fuel mass. The analyses are performed for a graphite moderating material, using a simple core model to easily identify the phenomena observed. It is found that it is necessary to reduce the fuel enrichment near the moderated regions in order to avoid unacceptable power peaking. In the end, use of moderating materials outside a SFR core does not provide significant benefit in term of fuel volume reduction, but allows for a noticeable reduction of the mass of fissile material needed. However, it also implies a number of additional challenges which are highlighted in this paper.

core optimization↗

Development of Irradiation Test Devices for Transient Testing

The Transient Reactor Test facility (TREAT) resumed operations in 2017 in order to reclaim its crucial role in nuclear-heated fuel safety research. TREAT’s historic era of operation (1959-1994) was best known for integral-scale testing of large fuel specimens/bundles under postulated reactor plant accident conditions, but TREAT also supported smaller-scale phenomena identification tests that elucidated fundamental behaviors and paved the way for these integral-scale tests. Advances in modern computational capabilities and a resurgence of interest in novel reactor technologies have created an opportunity for emphasizing modernized science-based and separate effects tests once again at TREAT. An innovative approach to this type of testing has been developed to leverage minor radioactivity built-in during brief TREAT irradiations by arranging smaller fuel specimens in low activation hardware so that they can be easily extracted and shipped for post irradiation examination within weeks. This recently-established capability, termed the Minimal Activation Retrievable Capsule Holder (MARCH) irradiation vehicle system, includes capabilities for cost-effective simplified-environment testing of centimeter-scale fuel samples of various geometries, temperature-controlled irradiations of millimeter-size samples for lower-length-scale model development, liquid-metal bonded heat sink capsules for controlling transient temperature response in fuel rodlets, and an innovative approach to high throughput irradiation of transient sensors and instrumentation. The MARCH system’s capabilities will also set the foundation for fuel safety research performed in larger integral-scale test devices with coolant environments representing reactor plants. Based upon historic approaches, but modernized to meet current nuclear technology needs, these larger irradiation devices include flowing pressurized water (including the ability to depressurize to steam) as well liquid metal cooling loops for various fuel rod and small bundle specimens. Here, this paper describes the recently-established MARCH system and current trajectory to enabling advanced transient science with a suite of irradiation test devices.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Visible-Light-Responsive Photocatalysis: Ag-Doped TiO2 Catalyst Development and Reactor Design Testing

In recent years, the alteration of titanium dioxide to become visible-light-responsive (VLR) has been a major focus in the field of photocatalysis. Currently, bare titanium dioxide requires ultraviolet light for activation due to its band gap energy of 3.2 eV. Hg-vapor fluorescent light sources are used in photocatalytic oxidation (PCO) reactors to provide adequate levels of ultraviolet light for catalyst activation; these mercury-containing lamps, however, hinder the use of this PCO technology in a spaceflight environment due to concerns over crew Hg exposure. VLR-TiO2 would allow for use of ambient visible solar radiation or highly efficient visible wavelength LEDs, both of which would make PCO approaches more efficient, flexible, economical, and safe. Over the past three years, Kennedy Space Center has developed a VLR Ag-doped TiO2 catalyst with a band gap of 2.72 eV and promising photocatalytic activity. Catalyst immobilization techniques, including incorporation of the catalyst into a sorbent material, were examined. Extensive modeling of a reactor test bed mimicking air duct work with throughput similar to that seen on the International Space Station was completed to determine optimal reactor design. A bench-scale reactor with the novel catalyst and high-efficiency blue LEDs was challenged with several common volatile organic compounds (VOCs) found in ISS cabin air to evaluate the system's ability to perform high-throughput trace contaminant removal. The ultimate goal for this testing was to determine if the unit would be useful in pre-heat exchanger operations to lessen condensed VOCs in recovered water thus lowering the burden of VOC removal for water purification systems.

Photocatalysis↗

Postirradiation examination on metallic fuel in the AFC-2 irradiation test series

In this paper, irradiation experiments on metallic fuel alloys containing rare earth additions to simulate potential carry-over from pyro-metallurgical reprocessing and minor actinide additions were performed in the Idaho National Laboratory Advanced Test Reactor. These tests were designated AFC-2A and AFC-2B. Additionally irradiation experiments were also performed on metallic fuel alloys containing minor actinide additions that were fabricated by different techniques. These tests were designated AFC-2E. These pins were removed from the reactor after achieving burnups between 6 and 11% fission per initial heave metal atom. Examination of these pins revealed that they were unintentionally operated beyond their desired power and temperature conditions. Highlights from the postirradiation examination of these experiments is discussed. A variety of issue contributed to the poor performance of these irradiation tests including capsule design, reactor power variations and fabrication issues. While all the issues contributed, the major issue was determined to be unanticipated variations in reactor power. Through comparisons between these experiments and historical off-normal experiments, it was possible to conclude bound the operating temperatures of these experiments. There likely was some in-pile melting in the rare earth addition experiments (AFC-2A, AFC-2B), but it is not likely that there was in-pile melting in the fabrication technique experiments (AFC-2E).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Application of a Virtual Reactivity Feedback Control Loop in Non-Nuclear Testing of a Fast Spectrum Reactor

For a compact, fast-spectrum reactor, reactivity feedback is dominated by core deformation at elevated temperature. Given the use of accurate deformation measurement techniques, it is possible to simulate nuclear feedback in non-nuclear electrically heated reactor tests. Implementation of simulated reactivity feedback in response to measured deflection is being tested at the NASA Marshall Space Flight Center Early Flight Fission Test Facility (EFF-TF). During tests of the SAFE-100 reactor prototype, core deflection was monitored using a high resolution camera. "virtual" reactivity feedback was accomplished by applying the results of Monte Carlo calculations (MCNPX) to core deflection measurements; the computational analysis was used to establish the reactivity worth of van'ous core deformations. The power delivered to the SAFE-100 prototype was then dusted accordingly via kinetics calculations, The work presented in this paper will demonstrate virtual reactivity feedback as core power was increased from 1 kilowatt(sub t), to 10 kilowatts(sub t), held approximately constant at 10 kilowatts (sub t), and then allowed to decrease based on the negative thermal reactivity coefficient.

Bragg-Sitton, Shannon M.↗

An Approach to Assessing the Added Mass for a Plate in a Channel

The Global Threat Reduction initiative (GTRI) was established by the National Nuclear Security Administration (NNSA) in 2004. One of the highlights of the program is to convert research and test reactors at home and abroad from Highly Enriched Uranium (HEU) to Low Enriched Uranium (LEU) fuels. By switching directly from HEU to LEU, an LEU reactor produces fewer neutrons than an HEU reactor, and in some cases, a direct switch from HEU to LEU results in the reactor being unable to achieve criticality. Under certain circumstances, criticality is achieved and the original neutron fluxes are restored with LEU fuel by adding more fuel elements to the core. Not all reactors, exemplified by the Advanced Test Reactor (ATR) at the Idaho National Lab (INL), have the luxury of simply adding more fuel to the core. In such cases, entirely new designs must be created and tested. The ATR utilizes plate type fuel. During the design and testing of the ATR fuel, flow induced vibrations were identified as potential source for experiment and fuel failure. Flow induced vibrations are problematic to solve because both the frequency of excitation and the modal frequencies of the object need to be determined. For the frequency of the object the frequency is often determined, either theoretically or experimentally without any influence of fluid. When a fluid is introduced, the fundamental frequency of an object can be greatly reduced allowing for resonance between the excitation frequency and the fundamental frequency of the plate. The consequence of such resonance is often failure of the component. Current methods for determining the frequency of a body immersed in a fluid requires the use of multi-physics software in order to determine (if at all possible) the frequency of the object. The work herein provides an alternative means of calculating the frequency of a plate by combining plate frequency theory to determine the added mass on the plate when in the presence of narrow channels. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization of Silica Optical Fiber for High Temperature, Radiation Environments

The Department of Energy and Idaho National Laboratory are restarting the TREAT (Transient Reactor Test facility) reactor and are interested in updating the reactor's instrumentation regarding the analysis of the test fuel. Optical fibers' ability to make distributed temperature measurements coupled with its small footprint makes optical fiber a viable candidate to monitor fuel performance in the TREAT reactor. In addition to TREAT reactor, the U.S. Department of Energy and nuclear reactor companies like TerraPower have shown interest in using distributed optically based instrumentation for nuclear instrumentation in Next-Gen reactors. The work presented in this paper focuses on optimizing commercial silica optical fiber so that it can survive the temperatures and radiation fluences of the TREAT reactor and Next-Gen reactors. Temperatures in the TREAT reactor can spike to around 900 - 1000 C and so the goal of this work is to optimize optical fiber to survive these temperatures.

36 MATERIALS SCIENCE↗

SAS4A/SASSYS-1 Verification Testing for Sodium Fast Reactor Application: Acceptance Testing Report

AS4A/SASSYS-1 (SAS) is a simulation tool used to perform deterministic analyses of anticipated events as well as design basis and beyond design basis accidents for advanced liquid-metal-cooled nuclear reactors. With its origin as SAS1A in the late 1960s, the SAS series of codes has been under continuous use and development for over sixty years and represents a critical investment in safety analysis capabilities for the U.S. Department of Energy. To support the dedication effort, this report has been generated to provide a detailed description of the available verification testing. The verification testing presented in this report captures functionality testing, focusing mainly on the testing of specific functions and algorithms for accuracy and precision of output, and interface testing, focusing mainly on the testing of critical input parameters and their valid ranges. Although SAS was developed to support the analysis of any liquid-metal-cooled nuclear reactor, the testing described in this document primarily focuses on the verification of SAS capabilities as they relate to a generic pool-type Sodium Fast Reactor (SFR).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Introduction of the PELICAN loop, a Full-Scale Pressure Drop Test Facility

The Versatile Test Reactor (VTR) is a test reactor currently under development by the US Department of Energy. This reactor will rely on fast neutrons enabling novel and wide-ranging experiment to support the development of the various advanced reactor technologies. With the high flux achievable, accelerated testing of fluid and materials will be made possible. To support VTR design efforts [1], an experimental facility has been designed and constructed at Argonne National Laboratory to recreate the hydraulic flow conditions within the VTR’s primary heat transport system (PHTS). This facility, the Pressure drop Experimental Loop for Investigations of Core Assemblies in advanced Nuclear reactors, PELICAN, measures the pressure drop across a full-scale fuel assembly containing prototypic axial reflectors, fuel, and plena components. Here, we first describe the design considerations required to recreate aspects of the VTR. Then we discuss the design and construction of PELICAN to address these design requirements, the design and construction of the test articles placed inside PELICAN’s test section, and finally present some of the first experimental results.

Grannan, A. M.↗