Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Towards High-Speed friction stir welding of 25 mm Thick AA2139-T8: tool innovation and process development

Joining thick plates (≥ 12 mm) of aluminum (Al) alloys is challenging due to high tool forces, uneven material flow, and non-uniform heat distribution through the material’s thickness. Recent advancements in tool design and welding parameters for friction stir welding (FSW) in thick plates butt joining have encountered a developmental plateau, highlighting the need for innovative approaches to overcome existing limitations. Here, this study focuses on the systematic development of single-pass and double-pass FSW processes for high-strength aluminum alloy AA2139-T8, to improve joint efficiency and enable high-speed welding capabilities. Experimental evidence is presented for a novel tool design with opposing pin threads, enabling high-speed (178 mm/min) single-pass friction stir butt welding of 25 mm thick AA2139-T8. A series of FSW trials was conducted both in air and with a trailing water spray, using steel backing plates (BPs) to investigate the impact of quenching and cooling rates on process response and joint performance. A joint efficiency of 83% was attained using the novel tool features and effectively controlling process forces and thermal boundary conditions.

AA2139-T8↗
DOE OSTI2018

Phase-Field Modeling of Nugget Zone for a AZ31-Mg-Alloy Friction Stir Weld

This work presents simulation of microstructure evolution in the nugget zone (NZ) of a AZ31-Mg-alloy friction stir weld. The process parameters (tool geometrical characteristics, rotational speed, travel speed, applied load) have been correlated with the resulting microstructural features in the NZ of the weld (grain size and population) with the aid of the MICRESS software, which provides the ability to simulate both nucleation and grain growth during dynamic recrystallization phenomena evolving in the NZ during the weld thermal cycle. The input parameters of the developed model include the tool geometry, the welding conditions as well as the recrystallization energy, the grain boundary mobility and specific material properties. NZ microstructure obtained by simulation shows good agreement with experimental measurements for both grain population and size.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Characterization of Friction-Stir-Welded 316L Austenitic Stainless Steels

Fusion welding of austenitic stainless steels (ASSs) causes undesirable metallographic changes. An attempt has been made to join 3-mm-thick 316L ASS plates using friction stir welding and correlate the microstructural evolution and the mechanical properties under various welding conditions. Tungsten alloy (W-Re) tool was employed for welding. Successful joints were obtained within a range of traverse speeds (45-85 mm/min) used in this work. Various zones were observed across the joint line. The stir zone exhibited considerable grain refinement and traces of delta ferrite phase. EBSD images showed a decreasing grain size with increased traverse speed. XRD patterns and TEM images confirmed the existence of delta ferrite. The mechanical properties of the joints including microhardness, tensile strength, impact toughness and bending were further reported.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Evaluation of Plastic “Eta” Factor for Welds of SS316L(N) with High Strength Mismatch Ratio

Fracture testing standards of ASTM and ISO recommend expressions for plastic η factor of various fracture test specimen geometries to evaluate the fracture behavior of materials. These are intended for homogenous specimens, but according to ISO 15653, it can be extended for weldments up to a strength mismatch ratio (M) of 1.25. In practice, M > 1.25 is encountered in many applications. In the present study, η factor has been evaluated for welded compact tension specimens using a limit load-based approach. The η factors obtained using this approach for homogenous specimens with elastic–perfectly plastic material model are found to be within ± 4% of those from the ASTM E 1820-17a, thereby validating the procedure. For welds, the limit load is obtained from nonlinear (elastic–plastic) FE simulations. η factors for specimens with various crack lengths (a), weld width (h) and strength mismatch have been evaluated and found to be significantly influenced by these parameters. For M > 1.25, the estimated η values were found to be ~ 16% lower compared to that from the ASTM E 1820-17a. Thus, the use of the η values from the proposed method provides a conservative estimate of J–R curve for the welds. Further, it has been observed that depending on the slope of the blunting line, the J{sub Ic} value may vary significantly with the estimated η values.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Electron Beam Welding of Nimonic 80A Superalloy: Microstructure Evolution and EBSD Study After Aging Heat Treatment

The purpose of this research was to evaluate integrity and microstructure changes of the electron beam-welded Nimonic 80A and the base metal after aging heat treatment process, i.e., 700 °C/72 h/air cooling. Here, microstructure, microhardness and tensile were investigated by various tools, i.e., scanning electron microscope with energy-dispersive spectroscopy and electron backscatter diffraction, x-ray diffraction analysis and Vickers hardness. Evaluation of microstructure shows that the weld zone mainly consists of columnar dendrites. The effect of aging heat treatment on the microstructure morphology and phase structure is very limited. Also, it was observed that there are obvious segregation and precipitates in intracrystalline and along the grain boundaries after aging heat treatment. Electron backscatter diffraction results show that the weld zone and base metal have a clear difference in the grain boundary characterization and kernel average misorientation at room temperature and after aging heat treatment, which leads to a difference in microhardness of the weld zone. In addition, the relationship between microhardness and tensile strength is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Mechanical Properties and Corrosion Behavior of AA5754-AA6061 Dissimilar Aluminum Alloys Welded by Cold Metal Transfer

The trend of using lightweight materials in the automotive industry brings along the necessity of dissimilar welding of aluminum alloys such as AA5754 and AA6061. Hybrid structures in automobiles are subjected not only to mechanical forces but also corrosive effects of the environment. In this study, cold metal transfer welding, which is suitable for welding thin sheets and dissimilar materials, was applied to join AA5754 to AA6061. It was aimed to investigate the effect of weld heat input on mechanical properties and corrosion rate measured by the Tafel extrapolation method in 3.5 wt.% NaCl solution at room temperature. The tensile strength of AA5754-AA6061 joints tended to reduce with increasing heat input. Corrosion test results showed that the increased heat input decreased the corrosion resistance and caused intergranular corrosion besides pitting corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Investigation on Microstructure and Mechanical Properties of TA10–Q245R Composite Plate Formed by Explosive Welding

The titanium alloy TA10 and the carbon steel Q245R are welded by explosive welding, and post-weld heat treatment (PWHT) is carried out for the TA10–Q245R composite plate. Microstructure and mechanical properties of the composite plate are investigated both in as-welded (AW) condition and after PWHT, respectively. Results show that, in AW condition, the bonding interface of composite plate presents wavy morphology, and at both sides of the interface plastic deformation is generated to a certain degree. Near the interface interdiffusion zone of alloying elements exists, and no Fe-Ti intermetallic compound is produced at the interface. SEM images indicate that the tensile fracture of composite plate presents the characteristic of ductile fracture, and no defects such as gas pores or impurities are found on the surface of shear fracture. After PWHT, the interfacial microstructure of the composite plate is obviously changed. Compared with the mechanical properties of the composite plate in AW condition, both tensile strength and shear strength of the composite plate are decreased to a certain extent after PWHT. With various factors into consideration, the suitable heat treatment procedure of TA10–Q245R composite plate is determined as follows: 550 °C × 1.5 h.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of FSW Repairing Process on the Microstructures and Mechanical Properties of Friction Stir-Welded 6082Al Alloy

When two 42-mm 6082Al plates were welded by friction stir welding (FSW), a discontinuously distributing groove defect is formed on the surface of the joint. Subsequently, the FSW repairing process was conducted at the defect location. The influence of the repairing process on the microstructures and mechanical properties of the joints were studied, and a description of the softening mechanism of the repaired joints is provided. The results show that TMAZ at the advance side is the weakest zone of the as-welded joints. The repairing process increases the heat input into the joints and thus promotes the coarsening and transformation of the precipitates in the joints, which further weakens the repaired joints. The average tensile strength of the joints repaired with a 24-mm pin is 205 MPa, which is 91% of that of the as-welded joint. The tensile strength generally increases when the size of the repaired pin decreases. The average tensile strength of the joints repaired with an 8-mm pin is 220 MPa, which is equivalent to the initial joints.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Heat generation and deformation in ultrasonic welding of magnesium alloy AZ31

A dual-sonotrode edge welding setup and a finite element analysis (FEA) model were developed for ultrasonic welding (USW) of AZ31 magnesium alloy sheets. Sonotrode vibration was measured quantitatively by a high-speed camera and introduced into the model as the driving force. The transient temperature field on the edge of the sheets was captured by an infrared camera. The heat generation mechanism in USW was investigated by a parametric study on the friction coefficient. Friction at faying interface should be smaller than those at other interfaces to enhance heat generation. The model was then validated by the experimental thermal history at the faying interface and the full temperature field as well as sonotrode indentation. Using the established model, USW under different welding powers (or vibration amplitudes) but at the same energy input was analyzed to characterize USW bond condition. Much higher temperature in the weld was observed with increasing vibration amplitudes, while reasonable indentation was maintained. Furthermore, vibration amplitude other than energy input was a critical factor in bond formation between AZ31 sheets.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗
DOE OSTI2020

On residual stress analysis and microstructural evolution for stainless steel type 304 spent nuclear fuel canisters weld joint: Numerical and experimental studies

Chloride-induced stress corrosion cracking (CISCC) in the weldments of austenitic stainless steel canisters is one of the primary safety concerns during the dry storage of used nuclear fuel at Independent Spent Fuel Storage Installations in coastal areas. In order to evaluate the CISCC behavior in the canister, a 3D sequentially coupled thermo-mechanical finite element model was built to simulate the residual stresses induced by two intersecting longitudinal and circumferential multi-pass welds in austenitic stainless steel mockup canister. Weld-induced residual stresses from simulation were in good agreement with the experimental measurement results by deep-hole drilling and contour methods. Through-wall high tensile axial and hoop stresses were observed in both the fusion zone and heat affected zone (HAZ) in the longitudinal and circumferential weld, respectively. On the other hand, the microstructure within the weldments of 304 stainless steel mockup was characterized using optical microscopy, scanning electron microscopy, electron back-scattered diffraction and energy dispersive X-ray spectroscopy methods. A few amount of MnS inclusions in both the base metal and HAZ, and a lot of (Mn,Si) x O y inclusions in the fusion zone were found. Meanwhile, there is some α'-martensite in the base metal, while the martensite was reversed in the HAZ. In the fusion zone, there is a lot of δ-ferrite. The martensite reversion phenomenon was also verified by the combination of Feritscope test and thermal simulation, which could predict a martensite reversion temperature as 400C°. The welding residual stresses and microstructure analysis results could offer the instructive information for the prediction of CISCC behavior of the spent nuclear fuel canisters.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Friction stir welding of multi-walled carbon nanotubes reinforced Al matrix composites

Highlights: • Al/MWCNT composites were successfully welded using friction stir welding. • After FSW, the composites possessed an excellent balance of mechanical properties. • High tensile strength and elongation over BM owing to MWCNTs after FSW. • Microstructures were investigated according to MWCNT contents and FSW conditions. - Abstract: In this study, we prepared composites between Al and multi-walled carbon nanotubes (MWCNTs) using the friction stir welding (FSW) method and investigated their microstructural evolution and mechanical properties by controlling the amount of MWCNT (1 and 3 vol%) and the plunging load (400 and 600 kg) used. After the FSW process, MWCNT showed slight coarsening of grain with random shear textures and accumulated dislocations; the differences obtained by varying the plunging load and MWCNT amount were insignificant. The friction-stir welded composite obtained using 3 vol% MWCNT and a plunging load of 600 kg possessed two-times better balance between strength and ductility than the base metal, due to the presence of both MWCNTs and the partially decomposed Al{sub 4}C{sub 3} in the composite.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Molten pool dynamics and humping suppression in high-speed laser welding via tailored beam configurations

High-speed laser welding is essential for increasing the production rate of fuel cell fabrication. However, when the welding speed exceeds a critical limit, humping occurs and reduces the weld quality. In this study, two tailored beam configurations, including an adjustable ring mode and a dual-beam configuration, were employed to suppress humping. Computational fluid dynamics simulations were performed to elucidate the underlying suppression mechanisms. Here, the results show that, in the adjustable ring mode, humping mitigation arises from a reduced backward cross-sectional melt flow rate and a more stable molten pool. In the dual-beam configuration, humping suppression is attributed to the deceleration of melt flow, the conduction-mode behavior of the trailing beam, and the widening of the molten pool induced by the trailing laser. Furthermore, because the dual-beam configuration directly modifies the trailing molten pool dynamics, it achieves more effective humping suppression, extending the welding speed limit to 1.50 m/s, compared with 1.00 m/s for the adjustable ring mode.

08 HYDROGEN↗
DOE OSTI2022

Experimental studies of a high-gradient X-band welded hard-copper split accelerating structure

We report on recent research on high-gradient radio frequency (RF) accelerating structures indicates that the use of hard copper alloys provides improvement in high gradient performance over annealed copper. Such structures are made by bonding individually manufactured parts. However, there are no well-established bonding techniques that preserve the hardness, surface finish and cleanliness required for high gradient operation. To preserve the copper hardness, RadiaBeam has developed a novel high-gradient split accelerating structure, based on electron beam welding joining technique. This technique provides efficient bonding with strong, clean welds and minimal thermal loading, while maintaining a clean inner RF environment. Our RF design and fabrication methodology limits the small heat affected zone to the outer cavity envelop, with virtually no distortions or thermal loading of critical RF surfaces. It also incorporates provisions to precisely control the gap despite conventional issues with weld joint shrinkage. To date we have manufactured and validated an RF accelerating structure joined by electron-beam welding that incorporates a novel open split design to significantly reduce the assembly complexity and cost. In this paper, we will present the electromagnetic design of this structure, discuss bonding, and present the results of high-power tests, where the accelerating gradients of 140 MV m -1 with surface peak fields of 400 MV m -1 were achieved for flat-top pulse length of 600 ns with an RF breakdown rate of 10 -4 1/(pulsecm).

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Validation of a lightning protection system for a fusion-welded thermoplastic composite wind turbine blade tip

Fusion welding for thermoplastic composite wind turbine blades is being investigated as a replacement for adhesives in bond lines to reduce manufacturing time and cost and to promote ease of recyclability. Resistance welding uses an electrically conductive material, such as carbon fiber, embedded in the bond line to heat the joining surfaces and fuse them together under pressure. One main challenge with fusion joining for large wind blades is the ability to use this conductive heating element in the bond line while still protecting the blade from the catastrophic effects of a lightning strike. This paper outlines the design and manufacturing of a lightning protection system for a 5-m-long thermally welded blade tip. The outcomes of high voltage and high current lightning testing applied to the 5 m blade tip show that the proposed design was able to protect the fusion welded bond lines from significant lightning damage.

17 WIND ENERGY↗
DOE OSTI2019

Advances in Dissimilar Metals Joining through Temperature Control of Friction Stir Welding

Lightweighting of vehicles and portable structures is an important undertaking. Multi-material design is required to achieve conflicting design targets such as cost, stiffness, and weight. Friction stir welding (FSW) variants, such as friction stir dovetailing and friction stir scribe, are enabling technologies for joining of dissimilar metals. This work shows that FSW variants are capable of joining aluminum to steel. Characteristics of metallurgical bonding at the dissimilar material interface are strongly affected by weld temperature. Control of FSW process temperature enables metallurgical bonding with suppressed formation of intermetallics at the dissimilar material interface resulting in improved mechanical properties relative to competing techniques. Temperature control is a powerful tool for process development and to ensure weld quality of dissimilar material welds.

Aluminum to Steel Joining, Friction stir welding, ↗
DOE OSTI2018

Influence of the Vapor Channel in Deep Laser Welding

The physical processes associated with deep welding are analyzed. A two-dimensional numerical model is proposed for the interaction of the laser beam with the medium in the vapor channel. The following processes are considered: heat and mass transfer; absorption and reradiation of the beam’s energy by the plasma; interaction of the plasma with the channel walls; and heat transfer to the cold sample. The model establishes a quantitative relation between the welding conditions and the results of butt welding. That decreases the expenditures in the development of laser-welding processes.

42 ENGINEERING↗
DOE OSTI2023

Microstructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.

36 MATERIALS SCIENCE↗