Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND MODELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

A method for predicting full scale buffet response with rigid wind tunnel model fluctuating pressure data. Volume 2: Power spectral densities for method assessment

The predicted upper and lower bounds power spectra for all of the cases and response items given in Volume 1 are plotted. The flight test power spectra are shown on each prediction plot for the nominal value of angle of attack that most closely agrees with the flexible angle for the prediction. The flight test and prediction conditions are given in tabular form for all cases considered.

Cunningham, A. M., Jr.↗

Some aerodynamic considerations related to wind tunnel model surface definition

The aerodynamic considerations related to model surface definition are examined with particular emphasis in areas of fabrication tolerances, model surface finish, and orifice induced pressure errors. The effect of model surface roughness texture on skin friction is also discussed. It is shown that at a given Reynolds number, any roughness will produce no skin friction penalty.

Gloss, B. B.↗

Static tests of the J97 powered, external augmenter V/STOL wind tunnel model

Results of the static testing (zero forward speed) of the J97-powered, external augmentor, large scale, V/STOL model are discussed. With a ground clearance of 7.5 feet, believed to have put the model essentially out of ground effect, a gross thrust augmentation ratio of 1.60 at nozzle pressure ratio (NPR) = 3.0 was measured for the fuselage augmentor. A similar figure was apparent for the wing augmentor. An overall ratio of model thrust to bare engine thrust of 1.52 was determined at NPR = 3.0. The structural integrity of the model was well demonstrated and duct pressure losses were small.

Garland, D. B.↗

Transonic flutter study of a wind-tunnel model of an arrow-wing supersonic transport

A 1/20-size, low-speed flutter model of the SCAT-15F complete airplane was tested on cables to simulate a near free-flying condition. Only the model wing and fuselage were flexible. Flutter boundaries were measured for a nominal configuration and a configuration with wing fins removed at Mach numbers M from 0.76 to 1.2. For both configurations, the transonic dip in the wing flutter dynamic pressure q boundary was relatively small and the minimum flutter q occurred near M = 0.92. Removing the wing fins increased the flutter q about 14 percent and changed the flutter mode from symmetric to antisymmetric. Vibration and flutter analyses were made using a finite-element structural representation and subsonic kernel-function aerodynamics. For the nominal configuration, the analysis (using calculated modal data) predicted the experimental flutter q levels within 10 percent but did not predict the correct flutter mode at the higher M. For the configuration without wing fins, the analysis predicted 16 to 36 percent unconservative (higher than experimental) flutter q levels and showed extreme sensitivity to mass representation details that affected wing tip mode shapes. For high subsonic M, empennage aerodynamics had a significant effect on the predicted flutter boundaries of several symmetric modes.

Ruhlin, C. L.↗

Transonic flutter and gust-response tests and analyses of a wind-tunnel model of a torsion free wing airplane

An exploratory study of a 1/5.5 size, complete airplane version of a torsion free wing (TFW) fighter aircraft was conducted. The TFW consisted of a wing/boom/canard assembly on each fuselage side that was interconnected by a common pivot shaft so that the TFW could rotate freely in pitch. The effect of the TFW was evaluated by comparing data obtained with the TFW free and the TFW locked to the fuselage. With the model mounted on cables to simulate an airplane free flying condition, flutter boundaries were measured at Mach number (M) from 0.85 to 1.0 and gust responses at M = 0.65 and 0.90. The critical flutter mode for the TFW free configuration was found experimentally to occur at M = 0.95 and had the rigid TFW pitch mode as its apparent aerodynamic driver.

Ruhlin, C. L.↗

Computation of wind tunnel model deflections

The experimental deflections for a transport type solid wing model were measured for several single point load conditions. These deflections were compared with those obtained by structural modeling of the wing by using plate and solid elements of Structural Performance Analysis and Redesign (SPAR) program. The solid element representation of the wing showed better agreement with the experimental deflections than the plate representation. The difference between the measured and calculated deflections is about 5 percent.

Mehrotra, S. C.↗

Transonic flutter study of a wind-tunnel model of a supercritical wing with/without winglet

The model was a 1/6.5-size, semipan version of a wing proposed for an executive-jet-transport airplane. The model was tested with a normal wingtip, a wingtip with winglet, and a normal wingtip ballasted to simulate the winglet mass properties. Flutter and aerodynamic data were acquired at Mach numbers (M) from 0.6 to 0.95. The measured transonic flutter speed boundary for each wingtip configuration had roughly the same shape with a minimum flutter speed near M=0.82. The winglet addition and wingtip mass ballast decreased the wing flutter speed by about 7 and 5 percent, respectively; thus, the winglet effect on flutter was more a mass effect than an aerodynamic effect.

Ruhlin, C. L.↗

An investigation of rotor harmonic noise by the use of small scale wind tunnel models

Noise measurements of small scale helicopter rotor models were compared with noise measurements of full scale helicopters to determine what information about the full scale helicopters could be derived from noise measurements of small scale helicopter models. Comparisons were made of the discrete frequency (rotational) noise for 4 pairs of tests. Areas covered were tip speed effects, isolated rotor, tandem rotor, and main rotor/tail rotor interaction. Results show good comparison of noise trends with configuration and test condition changes, and good comparison of absolute noise measurements with the corrections used except for the isolated rotor case. Noise measurements of the isolated rotor show a great deal of scatter reflecting the fact that the rotor in hover is basically unstable.

Sternfeld, H., Jr.↗

Transonic flutter study of a wind-tunnel model of a supercritical wing with/without winglet

The scaled flutter model was a 1/6.5-size, semispan version of a supercritical wing (SCW) proposed for an executive-jet-transport airplane. The model was tested cantilever-mounted with a normal wingtip, a wingtip with winglet, and a normal wingtip ballasted to simulate the winglet mass properties. Flutter and aerodynamic data were acquired at Mach numbers from 0.6 to 0.95. The measured transonic flutter speed boundary for each wingtip configuration had roughly the same shape with a minimum flutter speed near M = 0.82. The winglet addition and wingtip mass ballast decreased the wing flutter speed by about 7 and 5%, respectively; thus, the winglet effect on flutter was more a mass effect than an aerodynamic effect. Flutter characteristics calculated using a doublet-lattice analysis (which included interference effects) were in good agreement with the experimental results up to M = 0.82. Comparisons of measured static aerodynamic data with predicted data indicated that the model was aerodynamically representative of the airplane SCW.

Ruhlin, C. L.↗

The drag of magnetically suspended wind-tunnel models with nose-cones of various shapes

This article concerns the experimental determination of optimum nose-cones (minimum drag) of a body of revolution at supersonic and hypersonic speeds by means of ONERA magnetic suspension. The study concerns two groups of models, specifically: a group whose nose-cone has a profile in the shape of X(n); the AGARD B group whose nose-cone is plotted in accordance with a given law. The results obtained for the first group are comparable to those calculated with the approximations of Cole and Newton and the experiments carried out by Kubota.

Dubois, G.↗

A systematic plan for the continued study of dimensional stability of metallic alloys considered for the fabrication of cryogenic wind tunnel models

Interrelated research and development activities, phased development of stepped specimen program are documented and a sequence for a specific program of machining, validation and heat treatment cycles for one material are described. Proposed work for the next phase of dimensional stability research is presented and further technology development activities are proposed.

Wigley, D. A.↗

Wind-Tunnel-Model Leak-Checking System

Voice-actuated system allows one operator to do work of three. System uses voice-recognition-and-response unit and graphics terminal to interact with technician and to provide technician visual feedback. Computer-based Leakcheck system allows computer to do more of total work in checking model for leaks to reduce time and manpower required to perform task.

Larson, W. E.↗

Aerodynamic performance of a 27-percent-scale AH-64 wind-tunnel model with baseline/advanced rotor blades

Performance of a 27-percent scale model of an advanced rotor designed for the AH-64 helicopter was measured in hover and at forward speeds of 50 to 130 knots. A baseline rotor, modeled after the current AH-64 rotor, was also tested to provide data for comparison. The investigation was conducted to validate procedures used at Langley to design rotors with increased performance potential and to provide a database for evaluation of current and future rotor systems. Both rotors were operated at full-scale tip speeds. Rotor thrust, forward speed, and ground height were varied for each rotor.

Kelley, H. L.↗

Model 0A wind turbine generator FMEA

The results of Failure Modes and Effects Analysis (FMEA) conducted for the Wind Turbine Generators are presented. The FMEA was performed for the functional modes of each system, subsystem, or component. The single-point failures were eliminated for most of the systems. The blade system was the only exception. The qualitative probability of a blade separating was estimated at level D-remote. Many changes were made to the hardware as a result of this analysis. The most significant change was the addition of the safety system. Operational experience and need to improve machine availability have resulted in subsequent changes to the various systems which are also reflected in this FMEA.

Klein, William E.↗

Design and fabrication of instrumented composite airfoils for a cryogenic wind tunnel model

Two instrumented horizontal stabilizers and one instrumented vertical stabilizer were designed and fabricated for testing on the Pathfinder 1 (PF-1) Transport Model in the NASA Langley Research Center's National Transonic Facility (NTF). Two different designs were employed: the horizontal stabilizer utilized a metal spar and fiberglass overwrap and the vertical stabilizer was made of all fiberglass. All design requirements were met in terms of design loads, airfoil tolerances, surface finish, orifice hole quality, and proof-of-concept tests. Pressure tubing installation was found to be easier for these concepts as compared to methods used in conventional metallic models. Ease of repair was found to be a principal advantage in that some fabrication problems were overcome by reapplying fiberglass cloth and/or epoxy to damaged areas. Also, fabrication costs were judged to be lower when compared to the more conventional design fabrication costs.

Young, Clarence P., Jr.↗

Roll plus maneuver load alleviation control system designs for the active flexible wing wind-tunnel model

Three designs for controlling loads while rolling for the Active Flexible Wing (AFW) are discussed. The goal is to provide good roll control while simultaneously limiting the torsion and bending loads experienced by the wing. The first design uses Linear Quadratic Gaussian/Loop Transfer Recovery (LQG/LTR) modern control methods to control roll rate and torsional loads at four different wing locations. The second design uses a nonlinear surface command function to produce surface position commands as a function of current roll rate and commanded roll rate. The final design is a flutter suppression control system. This system stabilizes both symmetric and axisymmetric flutter modes of the AFW.

Moore, Douglas B.↗