SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This presentation discussed the most updated development of ceramic matrix composite by using a infiltration-free method for scale up as well as the concentrated solar plant impact by using this novel material.
Processes for tailoring the macroscopic shape, metallic composition, mechanical properties, and pore structure of nanoporous metal foams prepared through combustion synthesis via direct write 3D printing of metal energetic ligand precursor inks made with water and an organic thickening agent are disclosed. Such processes enable production of never before obtainable metal structures with hierarchical porosity, tailorable from the millimeter size regime to the nanometer size regime. Structures produced by these processes have numerous applications including, but not limited to, catalysts, heat exchangers, low density structural materials, biomedical implants, hydrogen storage medium, fuel cells, and batteries.
Fe-TiB 2 metal matrix composite, also called high-modulus steels (HMSs), are of great interest for applications in fuel-efficient transportation infrastructure, aerospace, and wear industries due to their high specific stiffness and yield strength. However, conventional cast Fe-TiB 2 HMSs often contain coarse and sharp-edged TiB 2 particles which easily trigger premature cracking during loading. Here, we synthesized a Fe-TiB 2 nanocomposite HMS via laser powder bed fusion (LPBF) additive manufacturing of mixed micro-sized powders of Fe, Ti, and Fe 2 B. We investigated the microstructure formation and mechanical behavior of the Fe-TiB 2 HMS. We found that in situ chemical reaction of Ti and Fe 2 B enables the formation of TiB 2 particles at nanoscale during rapid solidification of LPBF. These nanoscale TiB 2 particles can serve as heterogeneous nucleation sites and promote the formation of ultrafine and equiaxed α-Fe grains with random crystallographic textures, which differ from many other additively manufactured (AM) metal alloys characteristic of strong crystallographic textures. As such, isotropic mechanical properties were achieved in the AM Fe-TiB 2 nanocomposite HMS with a high elastic modulus of ~ 240 GPa, an exceptional yield strength of ~ 1450 MPa, and a large plasticity of ~ 20% under compression. Quantitative analysis reveals that the high yield strength primarily originates from strengthening contributions of the ultrafine grains with an average grain size of ~450 nm, the nanoscale TiB 2 reinforcing particles of 20–180 nm, and a high density of printing-induced dislocations of the order of 10 15 m –2 . In situ synchrotron high-energy X-ray diffraction unveils the load partitioning from the softer α-Fe matrix to the stiffer and stronger TiB 2 nanoparticles, contributing to the sustained strain hardening during compression. Our work not only provides a general pathway for achieving high-performance metal matrix nanocomposites by in situ chemical reaction and precipitation of ceramic nanoparticles during additive manufacturing, but also offers mechanistic insights into the deformation mechanism of nanoparticle-reinforced HMS composites.
Complex concentrated alloys (CCAs) are a system of alloys composition of nearly equiatomic elements, creating a state of high configurational entropy in the material. These alloys are of interest for various industrial applications due to their high strength and hardness, wide operational temperature range, creep and diffusion resistance, and radiation resistance. In the current work CoCrFeNi-base CCAs are synthesize by combining three commonly industrial alloys: IN718, SS316L, and 70Co30Cr (commercially known as Stellite 21), in-situ utilizing directed energy deposition (DED) additive manufacturing (AM). One bulk specimen is fabricated with a 1:1:1 ratio of IN718, SS316L, and 70Co30Cr where IN718 is a source of nickel and chrome, SS316 is a source of iron and chrome, and 70Co30Cr is a source of cobalt and supplemental chrome. Additionally, a functionally graded material (FGM) of the identified CCA system from SS316 was fabricated with 10 layers, where the initial five layers are the base material of SS316L and graded by steps of 20% to transition to the CCA system. Overall build quality, microstructure, compositional distribution, phases analysis, and microhardness were studied by laser optical microscopy, scanning election microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD), and Vickers microhardness techniques. Overall build quality showed a successful bulk build with acceptable density, however unmelted particles are observed in the as-built alloy. Compositional results show that the system meets the Boltzmann’s hypothesis definition of an HEA, and that an FCC CCA was produced with increased hardness, small grain size, and superior hardness properties to the SS316L substrate. While initial XRD results show predominately FCC structure, EDS analysis of interdendritic regions show the existence of Laves phases in the material. The fabrication of an FGM CCA allowed for potential screening of additional alloy mixes which may be of interest to explore in future research, and the resulting composition is compared to predicted values. This novel method of CCA fabrication results in substantial cost savings of these CCA systems over traditional methods.
The proposed project utilizes advanced ceramic-based 3D-printing technology to develop light, low-cost, ultra-compact, high-temperature high-pressure (HTHP) heat exchangers (HX) for the harsh oxidizing environment of aircraft gas-turbine engines. Typical 3D printing technologies (powder bed or lithographic techniques) cannot produce large high-density, monolithic ceramic material with intricate internal features and channels required for high-temperature, high-pressure recuperators. Furthermore, typical 3D printing technologies are not yet economical for large high-density components. A high-density material is required for hermeticity, high-temperature strength, and oxidation, corrosion, and wear resistance. The team has invented an extrusion-based additive manufacturing technology (referred to as robocasting) and developed processing techniques to tailor composition and rheological mix properties for rapid 3D printing of high-density alumina and SiC parts. The goal of the proposed project is to use robocasting technology to demonstrate commercializable high-density 3D-printed ceramic HX modules with high durability and quality, thereby reducing the risk of thermo-mechanical failure under extreme environments. In addition, the proposed project improves the quality of the ceramic 3D-printing process over a large printed area and HTHP operating conditions. Ceramic 3D printing technology also provides a means to create advanced topologies that are unobtainable with conventional manufacturing.
Thermal and simultaneous thermal and gamma radiation aging experiments were conducted on an industry grade cross-linked polyethylene (XLPE) cable insulation material, which is a composite material with XLPE as polymer matrix and various additives and fillers. Reverse engineering was conducted to identify and quantify the material composition given that this information was not revealed by the cable manufacture. Samples were then aged at temperatures of 60, 90, and 115 °C, exposed to gamma radiation for total doses of 0 to 324 kGy, and at dose rates of 0 to 540 Gy/h. Aging mechanisms were studied using various materials characterization techniques including pyrolysis gas chromatography mass spectrometry (Py-GCMS), differential scanning calorimetry (DSC), nuclear magnetic resonance spectroscopy (NMR), and gel-fraction tests. Results show that the flame-retardant components were decomposed into smaller molecules when the material was exposed to gamma radiation, while no changes were observed when the samples were aged thermally without gamma radiation. With exposure to gamma radiation, the crystalline phase of the XLPE were damaged by gamma radiation introducing defects in the crystals, resulting in smaller and less perfect crystals. The dominance of chain scission or chain reformation process largely depends on the chain mobility, which is decided by the aging temperature. Chain scission was seen to dominate when the material was exposed to gamma radiation at 60 °C. Chain cross-linking slightly dominated when the material was exposed to gamma radiation at 90 °C and became more dominant with exposure to gamma radiation at 115 °C. No significant change to the XLPE polymer matrix was observed when the samples were exposed to thermal aging without gamma radiation. Finally, antioxidant is more effective in protecting the XLPE polymer matrix under thermal aging, but less effective with sample exposure to gamma radiation.
In this project, we designed, synthesized and fabricated using X-winder technologies precommercialized novel, self-healingable commodity copolymer fiber-reinforced composites to extend the H 2 hose service life beyond the current target of 1000 fills. These studies demonstrated that these composites are able to withstand over 25,000 damage-repair cycles, which was the main objective of the proposed project, in the temperature range of -40 to +80 °C under variable pressures. When micro-cracks are formed after about 1,000 cycles/fueling per hose in the inner composite layer, these micro-cracks self-heal, thus extending the lifetime of a prototype inner layer of the hose. These composites were tested by exposure to H 2 fuel and demonstrated the ability to recover from mechanical damage. Thermomechanical testing combined with analysis of the stress and strain fields across the cross-section of the inner layer composite hoses also identified the ring-like stresses on the edge of inner layers arising from changes of the fiber winding angle directions from +45° to -45°. The developed novel concept that self-healing commodity copolymers can be used in the development of prototype composites for the extended service of H 2 dispensing hoses will have major implications for other energy-related technologies, where the extended service life in harsh environments is expected. In this project, we optimized, validated, and demonstrated novel copolymer fiber-reinforced composites for H 2 dispensing hose applications, which can be utilized in future manufacturing using commodity materials. The estimated cost of materials (exluding labor) is in the range of < $1.0/ft.
Rapid experimentation and characterization are ever-present needs in the discovery of high entropy alloys. High entropy alloy systems are difficult to survey with systematic composition sweeps using traditional synthesis methods. The number of distinct compositions in even a four-element system is experimentally intractable. Exploration of these, and higher-element systems, necessitates thermodynamic prediction coupled with an automated sample creation method and a rapid screening methodology to effectively down-select alloys with targeted properties. As a result, a high-throughput method for evaluating the oxidation performance of refractory high entropy alloys was developed and tested. The six-element system of aluminum, chromium, molybdenum, niobium, tantalum, and titanium was evaluated for single phase stability and short-duration oxidation resistance. Target compositions were initially determined via thermodynamic predictions of single-phase stability across a wide temperature range. A twenty-five-sample build plate was produced using directed energy deposition additive manufacturing. After fabrication, the twenty-five 1 cm 3 samples were heat treated and characterized for composition and phase identification. The build plate was exposed to a high temperature oxidizing environment at 1000 °C for three hours. After oxidation, the composition, morphology, and chemistry of the oxides formed were characterized. Of the twenty-five samples produced, nine exhibited a favorable oxidation response, from which a single-phase BCC alloy at a composition of Al 13 Cr 7 Mo 19 Nb 18 Ta 26 Ti 17 was identified as the alloy with the most protective oxidation coating with a thin, adherent oxide scale. Finally, the complete experimental down-selection—from machine setup to final alloy identification—required approximately 45 labor hours, demonstrating a rapid validation for alloy discovery.
This project “Improved Performance of Cu(InGa)(SeS) 2 PV Modules using the Reaction of Metal Precursors” was a partnership led by the Institute of Energy Conversion (IEC) at the University of Delaware with Columbia University and the Molecular Foundry at the Lawrence Berkeley National Laboratory. The aim was to develop pathways to improve Cu(InGa)(SeS) 2 (CIGSS) thin film photovoltaic modules using processes compatible with low manufacturing cost. The CIGSS approach investigated was a two-step process including deposition of metal precursor films following by reaction in hydride gases utilizing IEC’s novel reactor. The process was similar to that under commercial development by the project’s industry partner Stion. When Stion went out of business mid-project the focus changed to a rapid thermal process considered more commercially viable. Approaches to improve the performance of solar cells using the reacted films focused on two material innovations. First, the overall Ga content was increased to increase the operating voltage, which is desirable for scale-up to commercial modules. Second, the processing and performance advantages arising from Ag alloying were investigated. Advanced characterization guided process and material development including control of relative composition gradients. Research on the formation of Cu-Ga-In metal precursors utilized sputtering deposition which is normally used in commercial applications. The work resulted in processes for deposition of precursor stacks with increased relative Ga content and effects of deposition parameters on morphology and phase composition were established. It was shown that the metal precursor films have comparable phase composition and morphology so subsequent reaction follows from the same starting point. The addition of Ag to the metal precursors gave more uniform morphology and improved adhesion of reacted films which enable higher reaction temperature for faster processing. A novel outcome was the discovery of a previously undocumented material phase in sputter-deposited and evaporated Ag-Cu-In-Ga thin films. Hydride gas reaction processes including time-temperature-concentration profiles were developed for different precursor compositions. This enables control of composition profiles to engineer through-film gradients for solar cell optimization with characterization and simulations used to correlate measured film composition profiles to measurements of devices. In particular, the gradient of sulfur at the front of the CIGSS film was found to be critical. The simulations guided process development leading to improved reproducibility of devices improved performance with higher Ga content and higher voltage. With Ag-alloyed precursors, the reaction pathways leading were determined. A significant finding was that Ag-alloying increases the reaction rate to completely convert precursor films to the final chalcopyrite which could enable reduced reaction time to benefit manufacturability. To maintain potential commercial viability, the process under investigation was refocused to a rapid thermal process that could potentially be incorporated into an in-line process for manufacturing. Precursors with different composition were capped with an extra selenium layer and reacted in hydrogen sulfide 5-15 minutes, compared to typically 2 hours in the previous multi-step batch process. Critical RTP parameters were identified to control the reaction. Further optimization would be needed for high efficiency solar cells but pathways to high quality devices with further optimization and improved heating uniformity were developed. The project also developed new optoelectronic characterization approaches with a focus on development and application of spatial- and time-resolved photoluminescence and a custom mapping photoluminescence microscope built. It was shown how critical electronic transport properties strongly depend on the chemical composition of the material and that a wide range of samples show inhomogeneity on a length scale larger than the grains in the films. Additionally, two-photon excitation capability was developed to distinguish bulk vs surface losses. The project advances the state-of-the -art for precursor reaction processes in several ways that could impact manufacturing. This includes validation of approaches to increase voltage and establishment of model-guided control to form optimal composition profiles. The application of process control approaches with knowledge of phase formation and reaction pathways can be critically valuable in designing a large-scale process.
We fabricated nanocarbon metal composites (NCMC) of Al alloys with a process called “electrocharging assisted process” (EAP). This method consists of the application of a high current to a mixture of liquid metal and carbon particles. We investigated aluminum alloys (6061 and 1350) and used activated carbon and graphite powder as the source of carbon. The high current induces the formation of carbon chains and ribbons in the liquid metal. Upon solidification of the metal an epitaxial relation between the carbon nanostructures and the metal lattice is produced. The purpose of the project was to find the parameters during the reaction that would give rise to a high density of nanoribbons extending throughout the metal such that the electrical conductivity and the mechanical strength of the composite increased and that the method could be extended to large scale manufacturing. For this purpose, we designed two reactors for the incorporation of nanocarbon ribbons in aluminum metal. The first reactor was designed to have more control of the region with the high current density. However, there were problems with getting good mixing of the carbon in small volumes. A second reactor was designed with a stirrer that allowed for better mixing of the carbon by the introduction of argon gas through the shaft of the stirrer. NCMC were fabricated with a series of parameters to understand the role of current, time of applied current, type and shape of the cathode electrode and stirring speed of the mixture. We analyzed the composites by Raman scattering to gain information on the crystallite size of the nanocarbon, XRD to obtain the crystal structure of the composite, SEM and TEM to characterize the grain size of the aluminum grains and the quality of the crystal structure. We also measured the electrical conductivity and mechanical properties of selected samples. The nanocomposites showed increase in crystallite size of the nanocarbon with a linear dependence of the crystallite size on the duration of the applied current. There is a minimum current density necessary for the crystallite size to increase compared to the ~ 10 nm size of the activated carbon source used in the fabrication. The electrical conductivity of the nanocomposites increased with crystallite size of the nanocarbon and with the concentration of converted carbon. The maximum increase in electrical conductivity was 5.7% above the baseline for samples with ~ 4 wt % nanocarbon with crystallite size larger than 30 nm. These samples presented a hardness ~ 8% higher than the baseline samples with no carbon.
ULTIMATE is a leading-edge DOE program to develop ultrahigh temperature materials for gas turbine use in the aviation and power generation industries. This team, headquartered at West Virginia University and including collaborators from the National Energy Technology Laboratory and Advanced Manufacturing LLC, has developed a new class of ultra-high temperature Refractory Complex Concentrated Alloys-based Composites (RCCC) for high temperature applications such as combustion turbines used in the aerospace and energy industries. The RCCC consist of Refractory Complex Concentrated Alloys (RCCA) mixed with particles of Refractory High Entropy Carbides, to increase RCCA strength to withstand extreme conditions. These new materials optimize the balance among strength, creep (deformation), density, and stability at 1300 °C (2372 °F), while maintaining ductility once the alloy cools to room temperature. The research team has developed advanced manufacturing processes using the pulsed electric current and laser 3D printing to produce test coupons of these materials.
The CALPHAD system of fundamental phase-level databases, now known as the Materials Genome, has enabled a mature technology of computational materials design and qualification that has already met the acceleration goals of the national Materials Genome Initiative. Here, as first commercialized by QuesTek Innovations, the methodology combines efficient genomic-level parametric design of new material composition and process specifications with multidisciplinary simulation-based forecasting of manufacturing variation, integrating efficient uncertainty management. Recent projects demonstrated under the multi-institutional CHiMaD Design Center notably include novel alloys designed specifically for additive manufacturing. With the proven success of the CALPHAD-based Materials Genome technology, current university research emphasizes new methodologies for affordable accelerated expansion of more accurate CALPHAD databases. Rapid adoption of these new capabilities by US apex corporations has compressed the materials design and development cycle to under 2 years, enabling a new “materials concurrency” integrated into a new level of concurrent engineering supporting an unprecedented level of manufacturing innovation.
The Nuclear Materials Discovery and Qualification Initiative (NMDQi) is designed to accelerate nuclear materials qualification to fulfill the promises of early and advanced reactor technologies as a safe, clean, and low-cost baseload energy. Materials development and qualification in the nuclear industry is by definition challenging due to stringent safety requirements, limited availability of specialized facilities for materials irradiation and testing, and the challenging high-temperature, high-radiation environment. NMDQi will establish tools and capabilities that will greatly accelerate the nuclear fuels and materials development process. These tools will provide both computationally informed insights and high-throughput infrastructure with the goal of completing qualification in a single pass. In this approach, materials must be fabricated with a range of properties of interest so that materials performance can be examined in parallel, rather than with multiple discrete specimens. Advanced manufacturing (AM) techniques, which can produce complex component geometries, microstructures, and compositions, are ideal. The improved process monitoring and control that AM can provide are ideal for ensuring and reducing material variability, which will be particularly important as standards committees pursue regulations for AM components. However, gaining these benefits requires overcoming the substantial barrier of qualifying AM processes and the resulting materials and components for supporting research campaigns and eventually nuclear service.
In 2017, the Nuclear Forensics International Technical Working Group (ITWG) organized their fifth 37 Collaborative Materials Exercise (CMX-5). The exercise samples were two uranium dioxide fuel pellets 38 manufactured from the same starting materials by different processes to have similar bulk isotopic 39 composition, but different spatial uranium isotopic distributions. Sets of identical materials were sent to 40 all participating laboratories, who then utilized their existing nuclear forensic capabilities to 41 independently analyse fuel pellets and identify similarities and differences of the materials’ 42 characteristics. The analytical methods used to probe the fuel pellets included ex situ, such as sectioning 43 or breaking up the pellets and analyzing dissolved pieces using inductively coupled plasma mass 44 spectrometry (ICP-MS), analyzing particles collected from intact or fragmented pellets by secondary ion 45 mass spectrometry (SIMS), as well as in situ methods, such as laser ablation coupled with ICP-MS, 46 autoradiography and nanoSIMS. In this paper we present the results of these independent analyses and 47 compare the capabilities of those nuclear forensic analytical methods to uncover details of the isotopic 48 heterogeneity of uranium fuel pellets.
In this research, a smart manufacturing approach was used to enhance the mechanical properties of aluminum (Al) for lightweight applications. The smart manufacturing involved cryomilling of Al powders with and without 5 wt.% magnesium (Mg) powders for varying durations followed by a high-pressure cold spray (HPCS) additive manufacturing process to prepare bulk components. The morphological changes, crystallite size, and composition of the cryomilled powders and cold sprayed (CS’ed) components were examined using scanning electron microscopy (SEM), x-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques. The results showed that the crystallite size reduces with an increase in cryomilling time and the addition of Mg dopant. To test the mechanical properties of the bulk CS’ed components, microhardness tests were performed using a Vickers microhardness tester. Uniaxial tensile tests were also carried out to ascertain the material’s tensile properties. The mechanical testing results showed great improvement in the hardness and tensile strength of CS’ed Al–Mg samples as compared to pure Al samples. Subsequently, fractography analysis of the tensile failed samples was carried out to determine the nature of the failure. Here, the research article also discusses the inherent mechanisms for the improvement in mechanical properties of smart manufactured components as a result of Mg doping and cryomilling.
The main focus of this work was to evaluate additive manufacturing of metal molds, with significantly reduced cost and/or procurement lead time, for production of large composite components for mainstream (> 100k units/yr) automobiles. A two-component large tool with conformal heating channels was designed, optimized, printed, machined, and tested in production. The resulting analysis indicates that large scale AM is suitable for manufacturing complex geometry large scale metal molds.
This project seeks to develop device design, materials composition, and processing tools and parameters to fabricate semi-transparent perovskite solar cells and modules for application in stand-alone products or added to other solar cells in a mechanically stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of perovskite inks, scalable perovskite and heterojunction deposition and annealing processes, heterojunction composition, transparent electrode composition and deposition process, anti-reflection layer composition and deposition process, and cell to module integration processes. Modification 5: The proposed project seeks to develop device design, materials composition, and processing tools and parameters to fabricate semi-transparent perovskite solar cells and modules for application in stand-alone products or added to other solar cells in a mechanically-stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of perovskite inks, scalable perovskite and heterojunction deposition and annealing processes, heterojunction composition, transparent electrode composition and deposition process, passivation layers including in module scribes, anti-reflection layer composition and deposition process, and cell to module integration processes. Advanced metrology and characterization will be performed on perovskite films, cells and module. Furthermore, we will examine module or materials recycling for circular economy considerations. Modifcation 6: Gigahertz frequency microwave pump-probe spectroscopies are highly sensitive to thin film semiconductor photoconductivity of individual and stacks of layers that comprise perovskite solar cells. As such, these techniques will be used to qualify reproducibility and quality correlations during the manufacturing process. Modification 7: Mechanical adhesion of top contacts within perovskite modules significantly impacts the durability of the module when exposed to accelerated degradation testing. The adhesion between the perovskite/transport layer interface and the transport layer/top contact interface are both very sensitive small changes in processing. ALD processing conditions of the transport layer will be tuned to optimize the mechanical adhesion within the perovskite module stack.
Over the last few decades, several marine renewable energy (MRE) technologies, such as wave energy converters (WECs) and current energy converters (CECs), have been developed. As opposed to traditional materials such as metal alloys, the structure of these technologies is made up of polymer and polymer composite materials. Most structures have been made using thermoset polymer composites; however, since thermoset polymer composites are not recyclable and lack sustainability, and with recent innovations in recyclable resins, bio-based resins, and the development of additive manufacturing technologies, thermoplastic polymers are increasingly being used. Nevertheless, the methodologies for identifying end-of-life options and recovering these polymer composites, as well as the recycling and reuse processes for MRE structures, are not well-studied. Specifically, since these MRE structures are subjected to salinity, moisture, varying temperature, biofouling, and corrosion effects depending on their usage, the recyclability after seawater aging and degradation needs to be explored. Hence, this review provides an in-depth review of polymer composites used in marine applications, the hygrothermal aging studies conducted so far to understand the degradation of these materials, and the reuse and recycling methodologies for end-of-life MRE structures, with a particular emphasis on sustainability.