Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Cold-Sprayed NMC622 Composite as a Cathode for Lithium-Ion Batteries

The growing demand for high-energy, low-cost lithium-ion batteries (LIBs) to power electric vehicles (EVs) necessitates advances in both materials and manufacturing processes. Conventional cathode fabrication methods, such as slurry casting and drying, are energy-intensive and pose challenges for scalability and environmental compliance. In this study, we propose cold-spray (CS) deposition as a solvent-free approach for fabricating LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) composite cathodes. Powder blends of NMC622, poly(vinylidene fluoride) (PVDF), and carbon black (CB) are directly deposited onto stainless steel and Inconel substrates under varied gas temperatures, pressures (and thus velocities), and standoff distances. The effects of temperature on the deposit morphology, coating density, and volume are systematically investigated. Computational fluid dynamics simulations reveal that increasing the gas temperature enhances the particle velocity, narrows the spray angle, and reduces the mass concentration radially at the nozzle outlet. CS deposition results in a dense cathode microstructure, accompanied by fracture in polycrystalline NMC622 particles. X-ray diffraction analysis further verifies that there are no phase changes during the deposition process. The electrochemical performance of the cold-sprayed cathodes reveals an initial capacity of approximately 96 mAh g –1 for single-crystal NMC622 and 167 mAh g –1 for polycrystalline NMC622. While these values are modest compared to state-of-the-art slurry-cast cathodes, which typically exhibit 180–200 mAh g –1 under optimized conditions. The results demonstrate a competitive performance given the solvent-free nature of the CS process and compare favorably with tape-cast samples made from identical feedstock. In conclusion, he CS process enables the formation of dense, binder-integrated cathode coatings without the need for solvent processing, offering a promising pathway for scalable, energy-efficient dry electrode manufacturing of next-generation LIBs.

Batteries↗

Exploring the Limits of Bottom-Up Gold Filling to Fabricate Diffraction Gratings

Gold deposition on rotating disk electrodes, Bi 3+ adsorption on planar Au films and superconformal Au filling of trenches up to 45 μm deep are examined in Bi 3+ -containing Na 3 Au(SO 3 ) 2 electrolytes with pH between 9.5 and 11.5. Higher pH is found to increase the potential-dependent rate of Bi 3+ adsorption on planar Au surfaces, shortening the incubation period that precedes active Au deposition on planar surfaces and bottom-up filling in patterned features. Decreased contact angles between the Au seeded sidewalls and bottom-up growth front also suggest improved wetting. The bottom-up filling dynamic in trenches is, however, lost at pH 11.5. The impact of Au concentration, 80 mmol/L versus 160 mmol/L Na 3 Au(SO 3 ) 2 , on bottom-up filling is examined in trenches up to ≈ 210 μm deep with aspect ratio of depth/width ≈ 30. The microstructures of void-free, bottom-up filled trench arrays used as X-ray diffraction gratings are characterized by scanning electron microscopy (SEM) and Electron Backscatter Diffraction (EBSD), revealing marked spatial variation of the grain size and orientation within the filled features.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lithiation Gradients and Tortuosity Factors in Thick NMC111-Argyrodite Solid-State Cathodes

Achieving high energy density in all-solid-state lithium batteries will require the design of thick cathodes, and these will need to operate reversibly under normal use conditions. We use high-energy depth-profiling X-ray diffraction to measure the localized lithium content of Li 1-x Ni 1/3 Mn 1/3 Co 1/3 O 2 (NMC111) through the thickness of 110 μm thick composite cathodes. The composite cathodes consisted of NMC111 of varying mass loadings mixed with argyrodite solid electrolyte Li 6 PS 5 Cl (LPSC). During cycling at C/10, substantial lithiation gradients developed, and varying the NMC111 loading altered the nature of these gradients. Microstructural analysis and cathode modeling showed this was due to high tortuosities in the cathodes. This was particularly true in the solid electrolyte phase, which experienced a marked increase in tortuosity factor during the initial charge. Our results demonstrate that current distributions are observed in sulfide-based composites and that these will be an important consideration for practical design of all-solid-state batteries.

25 ENERGY STORAGE↗

Inhomogeneous Magnetic Anisotropy in an Fe 5– x GeTe 2 Nanoflake Observed by Imaging

Few-layer flakes of ferromagnetic Fe 5–x GeTe 2 with x = 0.3 (F5GT) possess a c-axis magnetocrystalline anisotropy that is large enough below ∼200 K to outcompete the easy-plane shape anisotropy, yielding distinctive magnetic microstructures with out-of-plane (OOP) magnetizations. Using photoemission electron microscopy (PEEM) with magnetic contrast from X-ray magnetic circular dichroism (XMCD) to study a thermally demagnetized h-BN-protected nanoflake of F5GT at 110 K, we observe a micron-scale coexistence between domains with OOP magnetizations (∼70% areal fraction) and hitherto unknown domains in which in-plane (IP) magnetization components dominate (∼30% areal fraction). The regions with dominant IP magnetization components do not correlate with small variations of flake thickness (6–10 nm) and instead arise from local changes of magnetocrystalline anisotropy due to a hitherto unidentified chemical inhomogeneity that we suggest to be a higher concentration of Fe vacancies. Our observation of micron-scale inhomogeneity would likely be missed if imaging a single flake orientation and should affect the viability and performance of van der Waals (vdW) spintronic devices with F5GT electrodes.

2D materials↗

Current Status on the Manufacturing of Nanomaterials for Proton Exchange Membrane Energy Systems by Vapor-Based Processes

Development of novel technologies for catalyst synthesis and membrane electrode assembly (MEA) fabrication is of primary importance for further improvement of the performance and economics of proton exchange membrane fuel cells (PEMFCs) and proton exchange membrane water electrolyzers (PEMWEs). While the traditional manufacturing methods are time-consuming, energy intensive, and require many processing steps, the new vapor-based methods provide many benefits including the development of improved catalysts and catalyst supports, deposition of uniform thin films, reduction of catalyst loading, and minimizing the number of manufacturing steps. Recent publications in the field identified spray pyrolysis, reactive spray deposition technology, chemical vapor deposition, and atomic layer deposition as advanced vapor-based catalyst synthesis and deposition methods used for fabrication of MEAs for PEMFCs and PEMWEs. Here, the MEAs fabricated via vapor-based processes have shown significant performance improvements in comparison to the state-of-the-art MEAs, which are attributed to better catalyst distribution, improved catalyst supports, and controlled, uniform catalyst layer microstructures. This review provides an overview of the vapor-based synthesis and deposition methods currently being used for the development of PEM-based devices. The advantages and disadvantages of these methods are critically compared and discussed while the outlook for future development is provided.

25 ENERGY STORAGE↗

Proton conductivity of potassium doped barium zirconates

Potassium doped barium zirconates have been synthesized by solid state reactions. It was found that the solubility limit of potassium on A-sites is between 5% and 10%. Introducing extra potassium leads to the formation of second phase or YSZ impurities. The water uptake of barium zirconates was increased even with 5% doping of potassium at the A-site. The sintering conditions and conductivity can be improved significantly by adding 1 wt% ZnO during material synthesis. The maximum solubility for yttrium at B-sites is around 15 at% after introducing 1 wt% zinc. The conductivity of Ba{sub 0.95}K{sub 0.05}Zr{sub 0.85}Y{sub 0.11}Zn{sub 0.04}O{sub 3-{delta}} at 600 deg. C is 2.2x10{sup -3} S/cm in wet 5% H{sub 2}. The activation energies for bulk and grain boundary are 0.29(2), 0.79(2) eV in wet 5% H{sub 2} and 0.31(1), 0.74(3) eV in dry 5% H{sub 2}. A power density of 7.7 mW/cm{sup 2} at 718 deg. C was observed when a 1 mm thick Ba{sub 0.95}K{sub 0.05}Zr{sub 0.85}Y{sub 0.11}Zn{sub 0.04}O{sub 3-{delta}} pellet was used as electrolyte and platinum electrodes. - Graphical abstract: Potassium doped barium zirconates have been synthesized by solid state reactions. It was found that the solubility limit of potassium on A-sites is between 5% and 10 %. The sintering conditions and conductivity can be improved significantly by adding 1 wt% ZnO during material synthesis. Five percent doping of potassium at A-site can double the total conductivity.

36 MATERIALS SCIENCE↗

3D-printed electrically conductive silicon carbide

The development of electrically conductive ceramics could achieve robust mechanical strength as well as practically high conductivity, offering applications in structural electrodes, conductors, catalyst supports, etc. However, its operating temperature is limited due to the intrinsic dense structures inevitably hindering the thermal management capability, thus resulting in a temperature-dependent electrical behavior in high-temperature environments. In this work, we report an additive manufacturing protocol through vat photopolymerization 3D printing to fabricate the architectured conductive silicon carbide (SiC) ceramics that simultaneously possess high electrical conductivity as well as low thermal conductivity, and demonstrate electric reliability under high-temperature environments above 600°C. The percolation of graphene into the ceramic scaffold establishes a uniform conductive network, exhibiting its electrical conductivity up to 1000 S m –1 . The bulk density of the 3D-printed ceramic is measured from 0.366 g cm –3 to 0.897 g cm –3 , with thermal conductivity ranging from 62 mW m –1 K –1 to 88 mW m –1 K –1 . Furthermore, the mechanical performance of conductive ceramic can be effectively reinforced by densifying the microstructures via spark plasma sintering treatment. The proposed additive manufacturing strategy widens the potential of ceramics as a structural and functional material, offering a promising pathway toward high-temperature electronics applications.

36 MATERIALS SCIENCE↗

Buta-1,3-diyne-Based π-Conjugated Polymers for Organic Transistors and Solar Cells

We report the synthesis and characterization of new alkyl-substituted 1,4-di(thiophen-2-yl)buta-1,3-diyne (R-DTB) donor building blocks, based on the -C≡C-C≡C- conjugative pathway, and their incorporation with thienyl-diketopyrrolopyrrole (R'-TDPP) acceptor units into π-conjugated PTDPP-DTB polymers (P1-P4). The solubility of the new polymers strongly depends on the DTB and DPP solubilizing (R and R', respectively) substituents. Thus, solution processable and high molecular weight PDPP-DTB polymers are achieved for P3 (R = n-C12H25, R' = 2- butyloctyl) and P4 (R = 2-ethylhexyl, R' = 2-butyloctyl). Systematic studies of P3 and P4 physicochemical properties are carried using optical spectroscopy, cyclic voltammetry, and thermal analysis, revealing characteristic features of the dialkynyl motif. For the first time, optoelectronic devices (OFETs, OPVs) are fabricated with 1,3-butadiyne containing organic semiconductors. OFET hole mobilities and record OPV power conversion efficiencies for acetylenic organic materials approach 0.1 cm2/(V s) and 4%, respectively, which can be understood from detailed thin-film morphology and microstructural characterization using AFM, TEM, XRD, and GIWAXS methodologies. Importantly, DTB-based polymers (P3 and P4) exhibit, in addition to stabilization of frontier molecular orbitals and to -C≡C-C≡C- relief of steric torsions, discrete morphological pliability through thermal annealing and processing additives. The advantageous materials properties and preliminary device performance reported here demonstrate the promise of 1,3-butadiyne-based semiconducting polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

IMPROVING INTERMEDIATE TEMPERATURE PERFORMANCE OF NI-YSZ CERMET ANODES FOR SOLID OXIDE FUEL CELLS BY INFILTRATION OF NICKEL NANOPARTICLES AND MIXED IONIC ELECTRONIC CONDUCTOR

Solid oxide fuel cells (SOFCs) are one of the most efficient and environment-friendly devices for electricity generation. One critical challenge of SOFC commercialization is high cell operating temperatures (800°C-1000°C), which lead to high material costs, high performance degradation rates, long start-up and shutdown times, and limited portable applications. Intermediate temperature (600°C-800°C) operation of SOFCs is limited by sluggish electrode reaction kinetics. The objective of this research is to improve intermediate temperature performance of commercially available Ni-YSZ cermet anode supported SOFCs by liquid infiltration of the anode. One effective method to improve kinetics of electrochemical reactions at the anode is to increase the density of reaction sites, which are known as the triple phase boundaries (TPBs). The porous Ni-YSZ cermet anodes were liquid infiltrated with Ni nanoparticles, leading to a four-fold increase in TPB density in the anode. The improved electrochemical performance of the infiltrated cells compared to the uninfiltrated cells highlights the effectiveness of anode infiltration in facilitating improved anode electrochemical reaction kinetics. However, the post-electrochemical testing characterization revealed that Ni nanoparticles were not stable due to Ni coarsening and were mostly isolated indicating that not all of the additional TPBs were fully utilized in electrochemical reactions due to the lack of an electronic pathway between the Ni nanoparticles. In order to improve microstructural stability of the infiltrated Ni nanoparticles, and to fully utilize the added TPBs, co-infiltration of Ni with a mixed ionic and electronic conductor (MIEC) was carried out. Two MIEC materials are chosen based on their chemical stability and conductivity in the anode operating environments; Gd 0.1 Ce 0.9 O 2-δ (GDC), a predominantly an ionic conductor, and La 0.6 Sr 0.3 Ni 0.15 Cr 0.85 O 3-δ (LSNC), a predominantly electronic conductor, and cells were successfully co-infiltrated to form Ni-GDC and Ni-LSNC nanostructures with the MIEC phases connecting the Ni nanoparticles. Stability tests demonstrated that both MIECs inhibited Ni nanoparticle coarsening. Electrochemical studies showed that Ni-GDC is the most effective for improved anode kinetics. A long-term (120 hours) electrochemical test indicated that infiltration of Ni-GDC into Ni-YSZ cermet anode effectively improves overall cell performance at intermediate temperatures and maintains the performance gain for a long period of time.

Lu, Yanchen↗

Synthesis and thermoelectric/electrical characterization of electrodeposited Sb{sub x}Te{sub y} thin films

Sb{sub x}Te{sub y} films were potentiostatically electrodeposited from acidic nitric baths at room temperature by controlling the applied potential. Near-stoichiometric Sb{sub 2}Te{sub 3} thin films were obtained at applied potentials between −0.15 and −0.30 V vs. saturated calomel electrode (SCE). Post-annealing in a reducing environment resulted in an improvement in the crystal structure without the evaporation of the Te element. This result was indicated by a significant reduction in the electrical resistance and decrease in the FWHM of the main diffraction peaks. The power factor (σS{sup 2}) increased from 44.2 to 372.1 μW/m K{sup 2} after annealing at 473 K.

36 MATERIALS SCIENCE↗

Meso-porous α-Fe{sub 2}O{sub 3} thin films synthesized via the sol-gel process for light-driven water oxidation

This work reports a facile and cost-effective method for synthesizing photoactive α-Fe{sub 2}O{sub 3} films as well as their performances when used as photoanodes for water oxidation. Transparent α-Fe{sub 2}O{sub 3} meso-porous films were fabricated by template-directed sol-gel chemistry coupled with the dip-coating approach, followed by annealing at various temperatures from 350 degrees C to 750 degrees C in air. α-Fe{sub 2}O{sub 3} films were characterized by X-ray diffraction, XPS, FE-SEM and electrochemical measurements. The photoelectrochemical performance of α-Fe{sub 2}O{sub 3} photoanodes was characterized and optimized through the deposition of Co-based co-catalysts via different methods (impregnation, electro-deposition and photo-electro-deposition). Interestingly, the resulting hematite films heat-treated at relatively low temperature (500 degrees C), and therefore devoid of any extrinsic dopant, achieve light-driven water oxidation under near-to-neutral (pH = 8) aqueous conditions after decoration with a Co catalyst. The onset potential is 0.75 V vs. the reversible hydrogen electrode (RHE), thus corresponding to 450 mV light-induced under potential, although modest photocurrent density values (40 μAcm{sup -2}) are obtained below 1.23 V vs. RHE. These new materials with a very large interfacial area in contact with the electrolyte and allowing for a high loading of water oxidation catalysts open new avenues for the optimization of photo-electrochemical water splitting. (authors)

08 HYDROGEN↗

On the preparation of TiAl alloy by direct reduction of the oxide mixtures in calcium chloride melt

In recent years, TiAl-based intermetallic alloys are being increasingly considered for application in areas such as (i) automobile/transport sector (passenger cars, trucks and ships) (ii) aerospace industry (jet engines and High Speed Civil Transport propulsion system) and (iii) industrial gas turbines. These materials offer excellent (i) high temperature properties (at higher than 6000C) (ii) mechanical strength and (iii) resistance to corrosion and as a result have raised renewed interest. The combination of these properties make them possible replacement materials for traditional nickel-based super-alloys, which are nearly as twice as dense (than TiAl based alloys). Since the microstructures of these intermetallic alloys affect, to a significant extent, their ultimate performance, further improvements (by way of alteration/modification of these microstructures), have been the subject matter of intense research investigations. It has now been established that the presence of alloy additives, such as niobium, tantalum, manganese, boron, chromium, silicon, nickel and yttrium etc, in specific quantities, impart marked improvement to the properties, viz. fatigue strength, fracture toughness, oxidation resistance and room temperature ductility, of these alloys. From a number of possible alloy compositions, {gamma}-TiAl and Ti-Al-Nb-Cr have, of late, emerged as two promising engineering alloys/materials. . The conventional fabrication process of these alloys include steps such as melting, forging and heat treatment/annealing of the alloy compositions. However, an electrochemical process offers an attractive proposition to prepare these alloys, directly from the mixture of the respective oxides, in just one step. The experimental approach, in this new process, was, therefore, to try to electrochemically reduce the (mixed) oxide pellet to an alloy phase. The removal of oxygen, from the (mixed) oxide pellet, was effected by polarizing the oxide pellet against a graphite electrode in a pool of molten calcium chloride at a temperature of 9000C. The dominant mechanism of the oxygen removal was the ionization of oxygen followed by its subsequent discharge, as CO2/CO, at the anode surface. The removal of oxygen from the oxide mixture helped form the alloy in situ. The presentation shall cover the detailed experimental results pertaining to the preparation, evaluation and characterization of Ti-47Al-2Nb-2Cr (atom%) alloy.

36 MATERIALS SCIENCE↗

Developing Stable Critical Materials and Microstructure for High-Flux and Efficient Hydrogen Production through Reversible Solid Oxide Cells

Reversible Solid Oxide Cells (RSOCs), which operate as either Solid Oxide Fuel Cells (SOFCs) or Solid Oxide Electrolytic Cells (SOECs), hold great promise for clean, high-efficiency energy conversion and hydrogen production. However, their commercial potential is hindered by stability issues arising from temperature-induced materials degradation. While substantial progress has been made in developing durable, reduced-temperature SOFCs - bringing them closer to commercial deployment, SOECs still exhibit substantially higher degradation rates at both the cell and stack levels under practical operating conditions.

08 HYDROGEN↗

Electrical and electrochemical performance of Mn{sub 3}O{sub 4} nanoparticles synthesized by hydrothermal method

Hausmannite Mn{sub 3}O{sub 4} nanoparticles have been synthesized by a simple hydrothermal method at low temperature. The microstructural, electrical and dielectric properties were studied. The XRD data exhibited different diffraction peaks along with predominant (211) orientation corresponds to tetragonal structure of Mn{sub 3}O{sub 4} with crystallite size of 65 nm. The SEM analysis reveals that the octahedral shape of grains with average grain size of 250 nm. The vibrational studies from Raman measurements confirmed the formation of Mn{sub 3}O{sub 4}. The impedance response of the Mn{sub 3}O{sub 4} sample was studied over the frequency range of 1 Hz – 1 MHz in the temperature range from room temperature to 373 K. The conductivity of the sample was observed to be increased (1.86 × 10{sup −5} S/m at 373 K) with temperature following the Arrhenius behavior with an estimated activation energy of 0.37 eV. The dielectric constant and dielectric loss were examined from 333 K to 373 K in the frequency range of 1 Hz – 1 MHz. The electrochemical performance of Mn{sub 3}O{sub 4} electrode was examined in 1M K{sub 2}SO{sub 4} aqueous electrolyte which exhibited a high specific capacitance of 356 F/g at a scan rate of 10 mV/s over a potential range −0.1 V – +0.9 V and showed excellent electrochemical stability during cycling.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dielectric and electrical studies of Pr{sup 3+} doped nano CaSiO{sub 3} perovskite ceramics

Highlights: • CaSiO{sub 3}:Pr{sup 3+} was prepared by facile low temperature solution combustion method. • The crystalline phase of the product is obtained by adopting sintering method. • Samples prepared at 500 °C and calcined at 900 °C for 3 h showed β-phase. • The Pr{sup 3+} doped CaSiO{sub 3} shows “unusual results”. • The electrical microstructure has been accepted to be of internal barrier layer capacitor. - Abstract: CaSiO{sub 3} nano-ceramic powder doped with Pr{sup 3+} has been prepared by solution combustion method. The powder Ca{sub 0.95}Pr{sub 0.05}SiO{sub 3} is investigated for its dielectric and electrical properties at room temperature to study the effect of doping. The sample is characterized by X-ray diffraction and infrared spectroscopy. The size of either of volume elements of CaSiO{sub 3}:Pr{sup 3+} estimated from transmission electron microscopy is about 180–200 nm. The sample shows colossal dielectric response at room temperature. This colossal dielectric behaviour follows Debye-type relaxation and can be explained by Maxwell–Wagner (MW) polarization. However, analysis of impedance and electric modulus data using Cole–Cole plot shows that it deviates from ideal Debye behaviour resulting from the distribution of relaxation times. The distribution in the relaxation times may be attributed to existence of electrically heterogeneous grains, insulating grain boundary, and electrode contact regions. Doping, thus, results in substantial modifications in the dielectric and electrical properties of the nano-ceramic CaSiO{sub 3}.

36 MATERIALS SCIENCE↗

Alternating chempolishing and electropolishing for interior and exterior surface finishing of additively manufactured (AM) metal components

Additively manufactured (AM) components’ surface finishing is crucial in adopting them for intended applications in challenging environments involving fatigue, corrosion, high temperature, and nuclear radiation. In our prior research, chempolishing (C) was utilized as an electroless etching process that uniformly smoothens complex AM components’ accessible interior and exterior surfaces (Tyagi et al. Additive Manufacturing, 25:32–38, 22). A wide range of electropolishing (E) has been demonstrated for AM surface finishing. However, electropolishing can impact a surface that can be juxtaposed to counter electrode and can yield a very smooth surface to sub-micrometer level roughness. However, a knowledge gap exists about the impact of applying both approaches on the same surface one after another and what new advantages may arise because of combining two methods. This paper uses dual-stage liquid-based surface finishing strategies produced by alternating the chempolishing (C) and electropolishing (E) steps. Two dual-stage surface finishing approaches, i.e., chempolishing followed by electropolishing (CE) and electropolishing followed by chempolishing (EC), were performed on the 316 stainless AM steel component. Impacts of EC and CE approaches were compared with single-stage C and E surface finishing approaches. An optical microscope and mechanical profilometer were utilized to investigate the wide range of surface roughness parameters. CE and EC produced Ra ~ 1.4 µm and ~ 1.6 µm, respectively. Surface roughness on CE- and EC-treated AM samples was lower than those individually treated by C and E approaches. Scanning electron microscopy provided further insights into the microstructural difference between CE- and EC-treated AM samples. This paper reports a liquid contact angle study on CE- and EC-treated AM samples to provide insights into the relative difference in surface energy that is crucial for making coatings on AM parts. A spectroscopic reflectance study was also employed to register the difference in physical properties of AM components treated with CE and EC approaches. Further, this study reveals industrially practicable interior and exterior surface finishing approaches for complex AM metal components that require minimum tooling and real-time process monitoring.

36 MATERIALS SCIENCE↗

Hot sputtering of barium strontium titanate on nickel foils

The relationships linking temperature and voltage dependent dielectric response, grain size, and thermal budget during synthesis are illustrated. In doing so, it was found that maximizing thermal budgets within experimental bounds leads to electrical properties comparable to the best literature reports irrespective of the processing technique or microstructure. The optimal film properties include a bulk transition temperature, a room temperature permittivity of 1800, a voltage tuning ratio of 10:1 at 450 kV/cm, and a loss tangent less than 1.5% at 450 kV/cm. The sample set illustrates the well-known relationship between permittivity and crystal dimension, and the onset of a transition temperature shifts at very fine grain sizes. A brick wall model incorporating a high permittivity grain and a low permittivity grain boundary is used to interpret the dielectric data. However, the data show that high permittivity and tunability values can be achieved at grain sizes or film thicknesses that many reports associate with dramatic reductions in the dielectric response. These differences are discussed in terms of crystal quality and maximum processing temperature. The results collectively suggest that scaling effects in ferroelectric thin films are in many cases the result of low thermal budgets and the consequently high degree of structural imperfection and are not from the existence of low permittivity phases at the dielectric-electrode interface.

36 MATERIALS SCIENCE↗

Selective sodium-ion diffusion channels in Na 2 - x Fe 3 (PO 4 ) 3 positive electrode for Na-ion batteries

The electrochemical community around the world is focusing heavily on sodium-ion batteries R&D due to the huge abundance of sodium and need for large scale deployment of safe and inexpensive batteries for the electrical grid energy storage. Here, we observe the characterization of model parameters such as ionic diffusivity and interfacial kinetics, for a potential sodium-ion battery cathode material, Na 2 - x Fe 3 (PO 4 ) 3 , using experimental and computational investigations. The Na 2 - x Fe 3 (PO 4 ) 3 structure is characterized by two distinct one-dimensional (1-D) Na diffusion channels. Density Functional Theory (DFT) calculation reveals that Na is first fully removed from one of the channels followed by the subsequent removal of Na from the second channel. The experimental exploration reveals that, in the beginning of Na removal at 0 ≤ x ≤ 0.5; the sodium ion diffusivity is of the order of ~10 –11 cm 2 s –1 and then slightly decreases. This is further confirmed by comparing the calculated sodium diffusion barriers along the individual 1-D channels as well as between the channels. Nevertheless, the exchange current density slowly increases up to x=1.0 and remains quite constant thereafter. The magnitude of exchange current density is very low suggesting that the interfacial kinetics are the rate limiting factor. The obtained results indicate that Na 2 - x Fe 3 (PO 4 ) 3 could achieve better rate performance with long cycling stability through engineering of the particle morphology and microstructure.

25 ENERGY STORAGE↗