Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrode separator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Cycling performance of the iron-chromium redox energy storage system

Extended charge-discharge cycling of this electrochemical storage system at 65 C was performed on 14.5 sq cm single cells and a four cell, 867 sq cm bipolar stack. Both the anolyte and catholyte reactant fluids contained 1 molar concentrations of iron and chromium chlorides in hydrochloric acid and were separated by a low-selectivity, cation-exchange membrane. The effect of cycling on the chromium electrode and the cation-exchange membrane was determined. Bismuth and bismuth-lead catalyzed chromium electrodes and a radiation-grafted polyethylene membrane were evaluated by cycling between 5 and 85 percent state-of-charge at 80 mA/sq cm and by periodic charge-discharge polarization measurements to 140 mA/sq cm. Gradual performance losses were observed during cycling but were recoverable by completely discharging the system. Good scale-up to the 867 sq cm stack was achieved. The only difference appeared to be an unexplained resistive-type loss which resulted in a 75 percent W-hr efficiency (at 80 mA/sq cm versus 81 percent for the 14.5 sq cm cell). A new rebalance cell was developed to maintain reactant ionic balance. The cell successfully reduced ferric ions in the iron reactant stream to ferrous ions while chloride ions were oxidized to chlorine gas.

Gahn, R. F.↗
DOE OSTI2022

Implementation of Ion Mobility Spectrometry-Based Separations in Structures for Lossless Ion Manipulations (SLIM)

Structures for Lossless Ion Manipulations (SLIM) is a powerful variant of traveling wave ion mobility spectrometry (TW-IMS) that uses a serpentine pattern of microelectrodes deposited onto printed circuit boards to achieve ultralong ion path lengths (13.5 m). Ions are propelled through SLIM platforms via arrays of TW electrodes while RF and DC electrodes provide radial confinement, establishing near lossless transmission. The recent ability to cycle ions multiple times through a SLIM has allowed ion path lengths to exceed 1000 m, providing unprecedented separation power and the ability to observe ion structural conformations unobtainable with other IMS technologies. The combination of high separation power, high signal intensity, and the ability to couple with mass spectrometry places SLIM in the unique position of being able to address longstanding proteomics and metabolomics challenges by allowing the characterization of isomeric mixtures containing low abundance analytes.

Hollerbach, Adam L.↗
DOE OSTI2017

A multi-channel capacitive probe for electrostatic fluctuation measurement in the Madison Symmetric Torus reversed field pinch

A 40-channel capacitive probe has been developed to measure the electrostatic fluctuations associated with the tearing modes deep into Madison Symmetric Torus (MST) reversed field pinch plasma. The capacitive probe measures the ac component of the plasma potential via the voltage induced on stainless steel electrodes capacitively coupled with the plasma through a thin annular layer of boron nitride (BN) dielectric (also serves as the particle shield). When bombarded by the plasma electrons, BN provides a sufficiently large secondary electron emission for the induced voltage to be very close to the plasma potential. The probe consists of four stalks each with ten cylindrical capacitors that are radially separated by 1.5 cm. The four stalks are arranged on a 1.3 cm square grid so that at each radial position, there are four electrodes forming a square grid. Every two adjacent radial sets of four electrodes form a cube. The fluctuating electric field can be calculated by the gradient of the plasma potential fluctuations at the eight corners of the cube. The probe can be inserted up to 15 cm (r/a = 0.7) into the plasma. Furthermore, the capacitive probe has a frequency bandwidth from 13 Hz to 100 kHz, amplifier-circuit limit, sufficient for studying the tearing modes (5-30 kHz) in the MST reversed-field pinch.

47 OTHER INSTRUMENTATION↗
DOE OSTI2019

Electronic Structure and Performance Bottlenecks of CuFeO 2 Photocathodes

The path to realizing low-cost, stable, and earth-abundant photoelectrodes can be enabled through a detailed understanding of the optoelectronic properties of these materials by combining theory and experimental techniques. Of the limited set of oxide photocathode materials currently available, CuFeO 2 has emerged as a promising candidate warranting detailed attention. Here, highly compact thin films of rhombohedral (3R) CuFeO 2 were prepared via reactive co-sputtering. Despite its 1.43 eV indirect band gap, a cathodic photocurrent of 0.85 mA/cm 2 was obtained at 0.4 V versus reversible hydrogen electrode in the presence of a sacrificial electron acceptor. This unexpected performance was related to inefficient bulk charge separation because of the ultrafast (<1 ps) self-trapping of photogenerated free carriers. The electronic structure of 3R-CuFeO 2 was elucidated through a combination of optical and X-ray spectroscopic techniques and further complemented by first-principles computational methods including a many-body approach for computing the O K-edge X-ray absorption spectrum. Through resonant inelastic X-ray scattering spectroscopy, the visible absorption edges of CuFeO 2 were found to correspond to Cu → Fe metal-to-metal charge transfer, which exhibits a high propensity toward self-trapping. Findings of the present work enable us to understand the performance bottlenecks of CuFeO 2 photocathodes and suggest feasible strategies for improving material limitations.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Covalently Grafted Polysulfur–Graphene Nanocomposites for Ultrahigh Sulfur-Loading Lithium–Polysulfur Batteries

Although lithium–polysulfur (Li–polyS) batteries employing organic polymeric sulfur as a cathode material outperform the lithium–sulfur (Li–S) battery system, the relatively low sulfur loading (<2 mg cm –2 ) in the current Li–polyS batteries compromises the areal capacity, constraining their practicality. We present here a new cathode active material (a covalently grafted polysulfur–graphene nanocomposite (polySGN)) for ultrahigh-loading Li–polyS batteries. The new cathode active material polySGN offers several advantages: (i) the well-dispersed graphene sheets offer highly electrically conductive pathways for electrons to travel within the polySGN matrix; (ii) the intermediate organosulfide moieties alleviate irreversible sulfide deposition on electrodes; and (iii) the in situ formed coating layer on the cathode-side surface of the polymeric separator further reduces polysulfide migration. In conclusion, the Li–polyS batteries employing polySGN as the cathode active material accomplish the highest sulfur loading (up to 10.5 mg cm –2 ) and the highest areal capacity (~12 mA h cm –2 ) reported thus far in the literature.

25 ENERGY STORAGE↗
DOE OSTI2015

Plasmon-induced charge separation at two-dimensional gold semishell arrays on SiO{sub 2}@TiO{sub 2} colloidal crystals

Photoelectrodes based on plasmonic Au semishell (or halfshell) arrays are developed. A colloidal crystal consisting of SiO{sub 2}@TiO{sub 2} core-shell particles is prepared on a TiO{sub 2}-coated transparent electrode. A Au semishell (or halfshell) array is deposited by sputtering or evaporation on the colloidal crystal. An electrode with the semishell (or halfshell) array exhibits negative photopotential shifts and anodic photocurrents under visible light at 500-800 nm wavelengths in an aqueous electrolyte containing an electron donor. In particular, hydroquinone and ethanol are good electron donors. The photocurrents can be explained in terms of plasmon-induced charge separation at the Au-TiO{sub 2} interface.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cascade Dielectrophoretic Separation for Selective Enrichment of Polyhydroxybutyrate (PHB)-Producing Cyanobacterium Synechocystis sp. PCC 6803

Maintaining favorable biological productivities in photosynthetic biomanufacturing systems, especially when the risk of contamination with competing microbes is high, remains a challenge to achieve while maintaining economic feasibility. This study presents a dielectrophoresis (DEP)-based microfluidic approach for isolating a desired strain within a co-culture. The cyanobacterium Synechocystis sp. PCC 6803 (a strain capable of producing the bioplastic precursor polyhydroxybutyrate, or PHB) was enriched from mixed cultures containing the competing cyanobacterium Synechococcus elongatus PCC 7942 (which does not naturally produce PHB). A DEP cascade electrode system was established to increase purification efficiency through sequential enrichment, which leveraged inherent differences in cell morphology and dielectric properties, to achieve the selective separation of these strains under physiological conditions. A substantial increase in the relative abundance of PHB-producing cells was assessed by optical microscopy and flow cytometry characterization, confirming more than five-fold reduction of the Synechococcus fraction in the refined cell mix. The presented electrokinetic platform offers a scalable and effective approach for selectively enhancing desired microbial components within microbial biomanufacturing systems, leading towards improved product yields.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Selective single-atom adsorption for precision separation of lead ions in tap water via capacitive deionization

Capacitive deionization (CDI) offers a cost-effective and low-energy method for selective removal of Pb 2+ from drinking water. Modifying CDI electrode surfaces with functional groups presents a versatile approach to enhancing selective ion adsorption capacity. However, a comprehensive understanding of the selectivity and removal efficiency of Pb 2+ among diverse functional groups remains unexplored. Here, we investigated the effects of different functional groups (-SH, -COOH, and -NH 2 ) attached to the graphene oxide (GO) electrode surfaces on Pb 2+ selectivity and removal efficiency. Surprisingly, GO-COOH demonstrated single-atom adsorption of Pb 2+ , displaying superior removal efficiency and selectivity compared with -SH and -NH 2 , although -SH possesses significant chelation capability for Pb 2+ . Both density functional theory (DFT) calculations and X-ray pair distribution function (PDF) analyses confirmed that Pb 2+ exhibits a theoretically higher affinity to -COOH. Further, this research deepens our understanding of the interactions between functional groups and heavy metal ions, enabling selective and rapid separation of target cations for water purification.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1988

Automated seed manipulation and planting

Activities for the Fall Semester, 1987 focused on investigating the mechanical/electrical properties of wheat seeds and forming various Seed Planting System (SPS) concepts based on those properties. The Electrical Division of the design group was formed to devise an SPS using electrostatic charge fields for seeding operations. Experiments concerning seed separation using electrical induction (rearranging of the charges within the seed) were conducted with promising results. The seeds, when exposed to the high voltage and low current field produced by a Van de Graff generator, were observed to move back and forth between two electrodes. An SPS concept has been developed based on this phenomena, and will be developed throughout the Spring Semester, 1988. The Mechanical Division centered on SPS concepts involving valves, pumps, and fluids to separate and deliver seeds. An SPS idea utilizing the pressure difference caused by air as it rushes out of holes drilled in the wall of a closed container has been formulated and will be considered for future development. Also, a system of seed separation and delivery employing a combination of centrifugal force, friction, and air flow was considered.

Garcia, Ray↗
DOE OSTI2026

Electrochemical Recovery of Rare-Earth Elements from Coal Fly Ash Using Ionic Liquids as both Extractant and Electrolyte

Rare-earth elements (REEs) are critical for medical technologies, electronics, and clean energy. Coal fly ash (CFA), a byproduct of coal combustion, offers a promising alternative REE source. However, efficient extraction and separation of REEs from CFA remain challenging due to the complex composition of CFA. This study introduces a sustainable method for REE recovery using a recyclable ionic liquid, betainium bis(trifluoromethylsulfonyl)imide ([Hbet]- [Tf 2 N]), which serves both as the extractant from CFA and as the electrolyte in electrodeposition. In the first stage, [Hbet][Tf 2 N] preferentially extracts REEs from CFA through leaching. In the second stage, the REE-enriched ionic liquid undergoes electrochemical deposition using amperometry techniques, where REEs are reduced and deposited onto the electrode. The deposition experiments were conducted from −0.5 to −2.0 V vs a Pt quasireference electrode in a three-electrode setup comprising titanium as the working electrode and platinum as both the reference and counter electrodes. Varying the applied potential enabled potential-dependent preferential REE deposition. At −0.5 V, neodymium (Nd) showed preferential recovery, reaching 25% with a separation factor of 37 over other REEs. In contrast, applying a more negative potential increased overall deposition, yielding ∼50% Nd recovery and 10−20% recovery for the remaining REEs. After recovery, the ionic liquid was regenerated and reused for a subsequent electrochemical recovery cycle. Overall, this study demonstrates a feasible approach for REE recovery from CFA waste, with potential to enhance resource utilization within the REE supply chain.

coal fly ash↗
DOE OSTI2015

Parallel Electrochemical Treatment System and Application for Identifying Acid-Stable Oxygen Evolution Electrocatalysts

There are many energy technologies require electrochemical stability or preactivation of functional materials. Due to the long experiment duration required for either electrochemical preactivation or evaluation of operational stability, parallel screening is required to enable high throughput experimentation. We found that imposing operational electrochemical conditions to a library of materials in parallel creates several opportunities for experimental artifacts. We discuss the electrochemical engineering principles and operational parameters that mitigate artifacts int he parallel electrochemical treatment system. We also demonstrate the effects of resistive losses within the planar working electrode through a combination of finite element modeling and illustrative experiments. Operation of the parallel-plate, membrane-separated electrochemical treatment system is demonstrated by exposing a composition library of mixed metal oxides to oxygen evolution conditions in 1M sulfuric acid for 2h. This application is particularly important because the electrolysis and photoelectrolysis of water are promising future energy technologies inhibited by the lack of highly active, acid-stable catalysts containing only earth abundant elements.

14 SOLAR ENERGY↗
DOE OSTI2019

Continuous production of pure liquid fuel solutions via electrocatalytic CO 2 reduction using solid-electrolyte devices

Electrocatalytic CO 2 reduction is often carried out in a solution electrolyte such as KHCO 3 (aq), which allows for ion conduction between electrodes. Thus, liquid products that form are in a mixture with the dissolved salts, requiring energy-intensive downstream separation. In this work, we report continuous electrocatalytic conversion of CO 2 to pure liquid fuel solutions in cells that utilize solid electrolytes, where electrochemically generated cations (such as H+) and anions (such as HCOO–) are combined to form pure product solutions without mixing with other ions. Using a HCOOH-selective (Faradaic efficiencies>90%) and easily scaled Bi catalyst at the cathode, we demonstrate production of pure HCOOH solutions with concentrations up to 12M. We also show 100h continuous and stable generation of 0.1 M HCOOH with negligible degradation in selectivity and activity. Production of other electrolyte-free C 2+ liquid oxygenate solutions, including acetic acid, ethanol and n-propanol, are also demonstrated using a Cu catalyst. Lastly, we show that our CO 2 reduction cell with solid electrolytes can be modified to suit other, more complex practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of low-frequency voltage on nonlinear standing wave excitation, plasma uniformity, and ion dynamics in dual-frequency asymmetric capacitive discharges

Abstract It is known that in very-high-frequency (VHF) capacitively coupled plasmas, the higher harmonics generated by nonlinear sheath motion can enhance the standing wave effect (SWE), which can lead to center-peaked plasma density profiles. In this work, an improved nonlinear electromagnetic model incorporating a transmission line model, an electron momentum balance model, a bulk plasma model, a collisionless nonlinear numerical sheath model, and an ion Monte-Carlo collision (MCC) model is developed to study the effects of low-frequency (LF) voltage V L on the nonlinear standing wave excitation, plasma uniformity, and ion energy and angular distribution functions (IEDFs and IADFs) in dual-frequency (DF) asymmetric capacitive argon discharges at relatively low pressure of 3 Pa. The plasma diffusion in the radial direction and ion dynamics within the LF oscillating sheath are self-consistently considered. The LF voltage V L at 2 MHz varies from 0 to 700 V while the HF voltage V H at 60 MHz is fixed at 100 V. Simulation results indicate that without the addition of an LF source (i.e. V L = 0 V), there are a considerable number of high-order harmonics with short wavelengths, leading to significant SWE and central peak in the radial plasma density profile. Nevertheless, the high-order harmonic excitations tend to be weakened and merely occur around the phase of the full LF sheath collapse due to a shorter characteristic damping time of the surface waves as V L increases. This, combined with increased surface wavelengths of both the driving frequency and the higher harmonics at a higher V L , leads to suppressed standing waves and improved plasma uniformity. Meanwhile, the simulations show that both the low and the high energy peaks of IEDF move towards higher energies, and the energy peak separation width ΔEbecomes wider with the increase of V L . The IEDF at the radial center of the powered electrode exhibits a broader ΔEthan that at the edge. For the IADF, an increased V L results in more ions incident on the electrode with a smaller deflection angle. Because of a thinner sheath and a higher sheath voltage at the electrode center, the peak value of IADF at the electrode center is greater than that at the edge.

Physics↗
NASA NTRS2007

Rapid flow fractionation of particles combining liquid and particulate dielectrophoresis

Rapid, size-based, deposition of particles from liquid suspension is accomplished using a nonuniform electric field created by coplanar microelectrode strips patterned on an insulating substrate. The scheme uses the dielectrophoretic force both to distribute aqueous liquid containing particles and, simultaneously, to separate the particles. Size-based separation is found within nanoliter droplets formed along the structure after voltage removal. Bioparticles or macromolecules of similar size can also be separated based on subtle differences in dielectric property, by controlling the frequency of the AC current supplied to the electrodes.

King, Michael R.↗
DOE OSTI2017

Method and device for ion mobility separations

Methods and devices for ion separations or manipulations in gas phase are disclosed. The device includes a single non-planar surface. Arrays of electrodes are coupled to the surface. A combination of RF and DC voltages are applied to the arrays of electrodes to create confining and driving fields that move ions through the device. The DC voltages are static DC voltages or time-dependent DC potentials or waveforms.

47 OTHER INSTRUMENTATION↗
DOE OSTI2017

Efficient and Extensible Quasi-Explicit Modular Nonlinear Multiscale Battery Model: GH-MSMD

Complex physics and long computation time hinder the adoption of computer aided engineering models in the design of large-format battery cells and systems. A modular, efficient battery simulation model -- the multiscale multidomain (MSMD) model -- was previously introduced to aid the scale-up of Li-ion material and electrode designs to complete cell and pack designs, capturing electrochemical interplay with 3-D electronic current pathways and thermal response. Here, this paper enhances the computational efficiency of the MSMD model using a separation of time-scales principle to decompose model field variables. The decomposition provides a quasi-explicit linkage between the multiple length-scale domains and thus reduces time-consuming nested iteration when solving model equations across multiple domains. In addition to particle-, electrode- and cell-length scales treated in the previous work, the present formulation extends to bus bar- and multi-cell module-length scales. We provide example simulations for several variants of GH electrode-domain models.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Suppressing electrolyte-lithium metal reactivity via Li + -desolvation in uniform nano-porous separator

Lithium reactivity with electrolytes leads to their continuous consumption and dendrite growth, which constitute major obstacles to harnessing the tremendous energy of lithium-metal anode in a reversible manner. Considerable attention has been focused on inhibiting dendrite via interface and electrolyte engineering, while admitting electrolyte-lithium metal reactivity as a thermodynamic inevitability. Here, we report the effective suppression of such reactivity through a nano-porous separator. Calculation assisted by diversified characterizations reveals that the separator partially desolvates Li + in confinement created by its uniform nanopores, and deactivates solvents for electrochemical reduction before Li 0 -deposition occurs. The consequence of such deactivation is realizing dendrite-free lithium-metal electrode, which even retaining its metallic lustre after long-term cycling in both Li-symmetric cell and high-voltage Li-metal battery with LiNi 0.6 Mn 0.2 Co 0.2 O 2 as cathode. The discovery that a nano-structured separator alters both bulk and interfacial behaviors of electrolytes points us toward a new direction to harness lithium-metal as the most promising anode.

25 ENERGY STORAGE↗