Search NASA⌕ Search

SEARCH · Search NASA

Results for “high loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Knock Mitigation Effectiveness of EGR across the Pressure-Temperature Domain

Exhaust gas recirculation (EGR) has been shown to enable efficiency improvements in SI engines through multiple different mechanisms, including decreasing the knock propensity at high load, which allows higher compression ratio. While many of the benefits of EGR are applicable to both low and high power density engines, including reductions in pumping work and improved specific heat ratio, the knock benefits and corresponding compression ratio increases have been limited to low power density naturally aspirated engines primarily intended for hybrid vehicle architectures. An earlier study [1] indicated that there may be a kinetic limitation for the ability of EGR to mitigate knock under these conditions, but that study only considered a small number of conditions. In this investigation, we expand on that study while also providing data for model validation for the new light-duty combustion consortium from the U.S. Department of Energy: Partnership for Advancing Combustion Engines (PACE). In this investigation, the effectiveness of EGR to mitigate knock is studied with regards to the effect of engine speed (1,500 and 3,000 rpm), changing trajectory in the pressure-temperature domain by varying the intake manifold temperature (35, 60, and 90 deg C), and by considering the effect of minor species by studying the effect of untreated EGR vs. EGR that has been treated by an automotive three-way catalyst. Additionally, to increase the relevance of these data for future modeling studies, the performance of the full boiling range gasoline was compared relative to a surrogate formulation. The study found that the fuel surrogate performs well, confirmed the kinetic limitations of EGR to mitigate knock under boost, and showed improvements in EGR performance with catalyzed EGR.

42 ENGINEERING↗

Dynamic analysis of straight and involute tooth forms

The effect of load speed on straight and involute tooth forms is studied using several finite-element models. It is found that for rapidly rotating gears and sprockets, the load speed along the tooth surface can significantly affect the tooth vibration. Indeed, it is found that for sufficiently high load speeds and for sufficiently slender tooth forms, the tooth deflection can, at times, be directed opposite to the load direction. Comparisons are made of various dynamic models of gear and sprocket teeth. It is shown that for stubby tooth forms there is considerable difference between results obtained with finite element models and results obtained with Timoshenko beam models. Finally, it is shown that gear or sprocket vibrations can be induced by the shape of the tooth form itself. This effect becomes increasingly significant at higher speeds.

Lin, H. H.↗

Prediction of unsteady blade surface pressures on an advanced propeller at an angle of attack

The paper considers the numerical solution of the unsteady, three-dimensional, Euler equations to obtain the blade surface pressures of an advanced propeller at an angle of attack. The specific configuration considered is the SR7L propeller at cruise conditions with a 4.6 deg inflow angle corresponding to the +2 deg nacelle tilt of the Propeller Test Assessment (PTA) flight test condition. The results indicate nearly sinusoidal response of the blade loading, with angle of attack. For the first time, detailed variations of the chordwise loading as a function of azimuthal angle are presented. It is observed that the blade is lightly loaded for part of the revolution and shocks appear from hub to about 80 percent radial station for the highly loaded portion of the revolution.

Nallasamy, M.↗

Prediction of Unsteady Blade Surface Pressures on an Advanced Propeller at an Angle of Attack

The numerical solution of the unsteady, three-dimensional, Euler equations is considered in order to obtain the blade surface pressures of an advanced propeller at an angle of attack. The specific configuration considered is the SR7L propeller at cruise conditions with a 4.6 deg inflow angle corresponding to the plus 2 deg nacelle tilt of the Propeller Test Assessment (PTA) flight test condition. The results indicate nearly sinusoidal response of the blade loading, with angle of attack. For the first time, detailed variations of the chordwise loading as a function of azimuthal angle are presented. It is observed that the blade is lightly loaded for part of the revolution and shocks appear from hub to about 80 percent radial station for the highly loaded portion of the revolution.

Nallasamy, M.↗

Parameterizing the Variability and Uncertainty of Wind and Solar in CEMs

We present current and improved methods for estimating the capacity value and curtailment impacts from variable generation (VG) in capacity expansion models (CEMs). The ideal calculation of these variability metrics is through an explicit co-optimized investment-dispatch model using multiple years of VG and load data. Because of data and computational limitations, existing CEMs typically approximate these metrics using a subset of all hours from a single year and/or using statistical methods, which often do not capture the tail-event impacts or the broader set of interactions between VG, storage, and conventional generators. In our proposed new methods, we use hourly generation and load values across all hours of the year to characterize the (1) contribution of VG to system capacity during high load hours, (2) the curtailment level of VG, and (3) the reduction in VG curtailment due to storage and shutdown of select thermal generators. Using CEM model outputs from a preceding model solve period, we apply these methods to exogenously calculate capacity value and curtailment metrics for the subsequent model solve period. Preliminary results suggest that these hourly methods offer improved capacity value and curtailment representations of VG in the CEM from existing approximation methods without additional computational burdens.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Effects of Fuel Properties on Particle Number and Particle Mass Emissions from Lean and Stoichiometric Gasoline Direct Injection Engine Operation

Engine-out particle size distributions and soot mass emissions were measured from a gasoline direct injection (GDI) engine fueled by seven different gasoline formulations. Additionally, particle size distributions were simultaneously measured downstream of a catalyzed gasoline particulate filter (GPF) to determine the size resolved filtration efficiency. Stoichiometric, lean homogeneous, and lean stratified combustion modes were studied at four steady-state engine conditions. The particulate matter (PM) Index was calculated for each fuel as a function of the double bond equivalent and vapor pressure of the fuel components. There was generally poor correlation between particle number (PN)/PM mass emissions and the PM Index for steady state stoichiometric conditions with clean injectors, which emitted low particle concentrations. However, under high-load lean homogeneous conditions, there was good correlation between PN/PM mass emission and the PM Index, with the exception that the high ethanol content fuel produced significantly higher PM emissions than the other fuels. Under lean stratified conditions, most fuels produced similar particle size distributions and concentrations with the exception that the E50 fuel produced significantly lower concentrations than the other fuels. These results demonstrate the profound sensitivity of particle emissions from high ethanol content fuel to engine operating conditions. Additionally, these results show the predominant factor influencing particle formation is charge mixture formation, which fuel properties influence, but not as significantly as engine conditions. Here, the GPF reduced the tailpipe particle number concentrations by 60 - 95% and showed evidence of passive regeneration under higher load lean engine conditions (Temp>400°C, Lambda>1.3). Total PN filtration efficiencies ranged from ~60 % with a clean filter to greater than 95% with as little as 25 mg/L of soot loaded on the filter with a most penetrating particle size (MPPS) between 100 and 150 nm. The GPF results show that GPF regeneration can be achieved with the added fuel efficiency benefit of lean operation.

33 ADVANCED PROPULSION SYSTEMS↗

Load Bearing Equipment for Bone and Muscle

Resistance exercise on ISS has proven effective in maintaining bone mineral density and muscle mass. Exploration missions require exercise with similar high loads using equipment with less mass and volume and greater safety and reliability than resistance exercise equipment used on ISS (iRED, ARED, FWED). Load Bearing Equipment (LBE) uses each exercising person to create and control the load to the partner.

Shackelford, Linda↗

Building the Scale Model TELBOT Master Arm - 19585

For centuries, the art and science of modeling have gone hand in hand with the advancements of technology. Among the most impressive examples of the past modeling were ship models constructed for the British Royal Navy. Referred to as Admiralty models, they were principally constructed during the 18. and 19. centuries to depict proposed warship design. To this day, models are important in the field of engineering, where analytical modeling of a new design needs to be verified. In our project the old practice of building models will be fortified by the most advanced software and 3-D printing technology and used to manufacture a fully working Telbot Master Arm scaled down to 0.4-0.5 of its original size. The Telbot is a robotic arm used in different fields like the nuclear and chemical industry, often in combination with other products of our company. The main features of the Telbot's sleek construction are: 1) the high load capacity design; 2) unlimited rotation of all axes; 3) no external or internal wiring of the arm; 4) unlimited, fast and precise arm movements; 5) smooth and sealed arm bodies and joints; 6) high repeat accuracy; 7) resistance to radiation, and it can handle precise loads from 5 kg to 150 kg. Presently, to demonstrate such impressive design features and movement possibilities to its customers, HWM has to build a 3-D virtual reality simulation of the environment where Telbot is proposed to be used and then the arm simulates its movement in this environment. In addition, though HWM does have a showroom for Telbot, due to its weight and size it is not possible to take the full size Telbot on the road to show off its capabilities to customers. The challenge is to build a scaled down full working version of the Telbot robotic arm that can be moved in every direction and angle. The model will be based on the redeveloped T300 Telbot, with 3 joints and 7 free to move pivots. It will be at a 0.4 or 0.5 scale. The outer shell will be 3D printed. The sensors will forward the position and angle to HWM virtual reality software. With these features, any changes made on the model would get displayed in the software one-to-one. The result will be a Telbot Master arm model which can be easily transported; Waellischmiller would be able to present the Telbot not just virtually, but as a real product with all its functions and versatility and show it all over the world. The extensive construction of the virtual 3-D stimulation can be eliminated and the course of movement to reach specific positions could get simulated faster and easier. It can also be used internally and externally for training. This paper will address the challenges, materials used and manufacturing process of building a fully-working scaled-down version of the Telbot Master Arm. (authors)

3D PRINTING↗

Evaluation of the sensitivity and intrusion of workload estimation techniques in piloting tasks emphasizing mediational activity

In this experiment, pilots flew an instrumented moving-base simulator. Mediational loading was elicited by having them solve a variety of navigational problems. The problems were sorted into low, medium, and high load conditions based on the number and complexity of arithmetic and geometric operations required to solve them. Workload estimation techniques based on opinion, spare mental capacity, primary task performance, and physiological measures were obtained and compared. This paper describes: (1) the ability of the techniques to discriminate statistically between the three levels of loading conditions, and (2) changes in primary task performance caused by introduction of the workload technique procedures and equipment.

Rahimi, M.↗

Tortuosity Engineering for Improved Charge Storage Kinetics in High-Areal-Capacity Battery Electrodes

The increasing demands of electronic devices and electric transportation necessitate lithium-ion batteries with simultaneous high energy and power capabilities. However, rate capabilities are often limited in high-loading electrodes due to the lengthy and tortuous ion transport paths with their electrochemical behaviors governed by complicated electrode architectures still elusive. Here, we report the electrode-level tortuosity engineering design enabling improved charge storage kinetics in high-energy electrodes. Both high areal capacity and high-rate capability can be achieved beyond the practical level of mass loadings in electrodes with vertically oriented architectures. The electrochemical properties in electrodes with various architectures were quantitatively investigated through correlating the characteristic time with tortuosity. The lithium-ion transport kinetics regulated by electrode architectures was further studied via combining the three-dimensional electrode architecture visualization and simulation. Finally, the tortuosity-controlled charge storage kinetics revealed in this study can be extended to general electrode systems and provide useful design consideration for next-generation high-energy/power batteries.

25 ENERGY STORAGE↗

The Vital Function of Fe3O4@Au nanocomposites for Hydrolase Biosensor Design and Its Application in Detection of Methyl Parathion

A nanocomposite of gold nanoparticles (AuNPs) decorating a magnetic Fe3O4 core was synthesized using cysteamine (SH–NH2) as linker, and characterized by TEM, XPS, UV and electrochemistry. Then a hydrolase biosensor, based on self-assembly of methyl parathion hydrolase (MPH) on the Fe3O4@Au nanocomposite, was developed for sensitive and selective detection of the organophosphorus pesticide (OP) methyl parathion. The magnetic nanocomposite provides an easy way to construct the enzyme biosensor by simply exerting an external magnetic field, and also provides a simple way to renew the electrode surface by removing the magnet. Unlike inhibition-based enzyme biosensors, the hydrolase is not poisoned by OPs and thus is reusable for continuous measurement. AuNPs not only provide a large surface area, high loading efficiency and fast electron transfer, but also stabilize the enzyme through electrostatic interactions. The MPH biosensor shows rapid response and high selectivity for detection of methyl parathion, with a linear range from 0.5 to 1000 ng/mL and a detection limit of 0.1 ng/mL. It also shows acceptable reproducibility and stability. The simplicity and ease of operation of the proposed method has great potential for on-site detection of P–S containing pesticides and provides a promising strategy to construct a robust biosensor.

Au nanoparticles↗

Fumigation of Alcohol in a Light Duty Automotive Diesel Engine

A light-duty automotive Diesel engine was fumigated with methanol in amounts up to 35% and 50% of the total fuel energy respectively in order to determine the effect of alcohol fumigation on engine performance at various operating conditons. Engine fuel efficiency, emissions, smoke, and the occurrence of severe knock were the parameters used to evaluate performance. Raw exhaust particulate and its soluble organic extract were screened for biological activity using the Ames Salmonella typhimurium assay. Results are given for a test matrix made up of twelve steady-state operating conditions. For all conditions except the 1/4 rack (light load) condition, modest thermal efficiency gains were noted upon ethanol fumigation. Methanol showed the same increase at 3/4 and full rack (high load) conditions. However, engine roughness or the occurrence of severe knock limited the maximum amount of alcohol that could be fumigated. Brake specific nitrogen oxide concentrations were found to decrease for all ethanol conditions tested. Oxides of nitrogen emissions, on a volume basis, decreased for all alcohol conditions tested. Based on the limited particulate data analyzed, it appears that ethanol fumigation, like methanol fumigation, while lowering the mass of particulated emitted, does enhance the biological activity of that particulate.

Broukhiyan, E. M. H.↗

Multigrid Methods for EHL Problems

In many bearings and contacts, forces are transmitted through thin continuous fluid films which separate two contacting elements. Objects in contact are normally subjected to friction and wear which can be reduced effectively by using lubricants. If the lubricant film is sufficiently thin to prevent the opposing solids from coming into contact and carries the entire load, then we have hydrodynamic lubrication, where the lubricant film is determined by the motion and geometry of the solids. However, for loaded contacts of low geometrical conformity, such as gears, rolling contact bearings and cams, this is not the case due to high pressures and this is referred to as Elasto-Hydrodynamic Lubrication (EHL) In EHL, elastic deformation of the contacting elements and the increase in fluid viscosity with pressure are very significant and cannot be ignored. Since the deformation results in changing the geometry of the lubricating film, which in turn determines the pressure distribution, an EHL mathematical model must simultaneously satisfy the complex elasticity (integral) and the Reynolds lubrication (differential) equations. The nonlinear and coupled nature of the two equations makes numerical calculations computationally intensive. This is especially true for highly loaded problems found in practice. One novel feature of these problems is that the solution may exhibit sharp pressure spikes in the outlet region. To this date both finite element and finite difference methods have been used to solve EHL problems with perhaps greater emphasis on the use of the finite difference approach. In both cases, a major computational difficulty is ensuring convergence of the nonlinear equations solver to a steady state solution. Two successful methods for achieving this are direct iteration and multigrid methods. Direct iteration methods (e.g Gauss Seidel) have long been used in conjunction with finite difference discretizations on regular meshes. Perhaps one of the best examples of the application of such methods is the recent Effective Influence Method of Dowson and Wang. Multigrid methods have also been used with great success by Venner and Venner and Lubrecht with a good summary being given by Venner. As both these finite difference discretization based approaches appear to provide an efficient way of solving EHL problems, it is important to understand their relative merits. This paper is a first attempt at providing such an understanding in the context of EHL point contact problem, (contact of two spheres), in which the contact zone is a point and an ellipse or circle for unloaded and loaded dry contacts respectively. Since the film thickness and the contact width are generally small compared to the local radius of curvature of the two surfaces, the reduced geometry of the surfaces in the contact area can be accurately approximated to the contact between a paraboloid and a flat surface. The layout of the remainder of this paper is as follows. In section 2 we introduce the form of the equations to be solved. The Effective Influence Newton Method is described in Section 3 while Section 4 describes the Multigrid method to be used. Sections 5 and 6 describe the test problems to be used in the comparison between the two methods and compare the performance of the two methods. Section 7 concludes the paper with an argument of the two methods and suggests some future research directions.

Nurgat, Elyas↗

Experimental Study of the Effects of Periodic Unsteady Wakes on Flow Separation in Low Pressure Turbines

The present study, which is the first of a series of investigations of low pressure turbine (LPT) boundary layer aerodynamics, is aimed at providing detailed unsteady boundary layer flow information to understand the underlying physics of the inception, onset, and extent of the separation zone. A detailed experimental study on the behavior of the separation zone on the suction surface of a highly loaded LPT-blade under periodic unsteady wake flow is presented. Experimental investigations were performed on a large-scale, high-subsonic unsteady turbine cascade research facility with an integrated wake generator and test section unit. Blade Pak B geometry was used in the cascade. The wakes were generated by continuously moving cylindrical bars device. Boundary layer investigations were performed using hot wire anemometry at Reynolds number of 110,000, based on the blade suction surface length and the exit velocity, for one steady and two unsteady inlet flow conditions, with the corresponding passing frequencies, wake velocities, and turbulence intensities. The reduced frequencies cover the entire operation range of LP-turbines. In addition to the unsteady boundary layer measurements, blade surface pressure measurements were performed at Re = 50,000, 75,000, 100,000, 110,000, and 125,000. For each Reynolds number, surface pressure measurements are carried out at one steady and two periodic unsteady inlet flow conditions. Detailed unsteady boundary layer measurement identifies the onset and extension of the separation zone as well as its behavior under unsteady wake flow. The results, presented in ensemble-averaged and contour plot forms, help to understand the physics of the separation phenomenon under periodic unsteady wake flow.

Ozturk, Burak↗

Aerosol jet printed capacitive strain gauge for soft structural materials

Soft structural textiles, or softgoods, are used within the space industry for inflatable habitats, parachutes and decelerator systems. Evaluating the safety and structural integrity of these systems occurs through structural health monitoring systems (SHM), which integrate non-invasive/non-destructive testing methods to detect, diagnose, and locate damage. Strain/load monitoring of these systems is limited while utilizing traditional strain gauges as these gauges are typically stiff, operate at low temperatures, and fail when subjected to high strain that is a result of high loading classifying them as unsuitable for SHM of soft structural textiles. For this work, a capacitance based strain gauge (CSG) was fabricated via aerosol jet printing (AJP) using silver nanoparticle ink on a flexible polymer substrate. Printed strain gauges were then compared to a commercially available high elongation resistance-based strain gauge (HE-RSG) for their ability to monitor strained Kevlar straps having a 26.7?kN (6?klbf) load. Dynamic, static and cyclic loads were used to characterize both types of strain monitoring devices. Printed CSGs demonstrated superior performance for high elongation strain measurements when compared to commonly used HE-RSGs, and were observed to operate with a gauge factor of 5.2 when the electrode arrangement was perpendicular to the direction of strain.

36 MATERIALS SCIENCE↗

From Metal–Organic Frameworks to Single‐Atom Fe Implanted N‐doped Porous Carbons: Efficient Oxygen Reduction in Both Alkaline and Acidic Media

Abstract It remains highly desired but a great challenge to achieve atomically dispersed metals in high loadings for efficient catalysis. Now porphyrinic metal–organic frameworks (MOFs) have been synthesized based on a novel mixed‐ligand strategy to afford high‐content (1.76 wt %) single‐atom (SA) iron‐implanted N‐doped porous carbon (Fe SA ‐N‐C) via pyrolysis. Thanks to the single‐atom Fe sites, hierarchical pores, oriented mesochannels and high conductivity, the optimized Fe SA ‐N‐C exhibits excellent oxygen reduction activity and stability, surpassing almost all non‐noble‐metal catalysts and state‐of‐the‐art Pt/C, in both alkaline and more challenging acidic media. More far‐reaching, this MOF‐based mixed‐ligand strategy opens a novel avenue to the precise fabrication of efficient single‐atom catalysts.

Jiao, Long↗

From Metal-Organic Frameworks to Single-Atom Fe Implanted N-doped Porous Carbons: Efficient Oxygen Reduction in Both Alkaline and Acidic Media [From MOFs to Single Fe Atoms Implanted N-doped Porous Carbons: Efficient Oxygen Reduction in Both Alkaline and Acidic Media]

Here, it remains highly desired but a great challenge to achieve atomically dispersed metals in high loadings for efficient catalysis. Now porphyrinic metal–organic frameworks (MOFs) have been synthesized based on a novel mixed–ligand strategy to afford high–content (1.76 wt %) single–atom (SA) iron–implanted N–doped porous carbon (Fe SA –N–C) via pyrolysis. Thanks to the single–atom Fe sites, hierarchical pores, oriented mesochannels and high conductivity, the optimized Fe SA –N–C exhibits excellent oxygen reduction activity and stability, surpassing almost all non–noble–metal catalysts and state–of–the–art Pt/C, in both alkaline and more challenging acidic media. More far–reaching, this MOF–based mixed–ligand strategy opens a novel avenue to the precise fabrication of efficient single–atom catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗