Search NASA⌕ Search

SEARCH · Search NASA

Results for “interface velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

THE SINS SURVEY OF z {approx} 2 GALAXY KINEMATICS: PROPERTIES OF THE GIANT STAR-FORMING CLUMPS

We have studied the properties of giant star-forming clumps in five z {approx} 2 star-forming disks with deep SINFONI AO spectroscopy at the ESO VLT. The clumps reside in disk regions where the Toomre Q-parameter is below unity, consistent with their being bound and having formed from gravitational instability. Broad H{alpha}/[N II] line wings demonstrate that the clumps are launching sites of powerful outflows. The inferred outflow rates are comparable to or exceed the star formation rates, in one case by a factor of eight. Typical clumps may lose a fraction of their original gas by feedback in a few hundred million years, allowing them to migrate into the center. The most active clumps may lose much of their mass and disrupt in the disk. The clumps leave a modest imprint on the gas kinematics. Velocity gradients across the clumps are 10-40 km s{sup -1} kpc{sup -1}, similar to the galactic rotation gradients. Given beam smearing and clump sizes, these gradients may be consistent with significant rotational support in typical clumps. Extreme clumps may not be rotationally supported; either they are not virialized or they are predominantly pressure supported. The velocity dispersion is spatially rather constant and increases only weakly with star formation surface density. The large velocity dispersions may be driven by the release of gravitational energy, either at the outer disk/accreting streams interface, and/or by the clump migration within the disk. Spatial variations in the inferred gas phase oxygen abundance are broadly consistent with inside-out growing disks, and/or with inward migration of the clumps.

79 ASTRONOMY AND ASTROPHYSICS↗

INTERMEDIATE-MASS HOT CORES AT {approx}500 AU: DISKS OR OUTFLOWS?

Observations with the Plateau de Bure Interferometer in the most extended configuration toward two intermediate-mass star-forming regions, IRAS 22198+6336 and AFGL 5142, reveal the presence of several complex organic molecules at {approx}500 AU scales, confirming the presence of hot cores in both regions. The hot cores are not rich in CN-bearing molecules, as often seen in massive hot cores, and are mainly traced by CH{sub 3}CH{sub 2}OH, (CH{sub 2}OH){sub 2}, CH{sub 3}COCH{sub 3}, and CH{sub 3}OH, with, additionally, CH{sub 3}CHO, CH{sub 3}OD, and HCOOD for IRAS 22198+6336, and C{sub 6}H and O{sup 13}CS for AFGL 5142. The emission of complex molecules is resolved down to sizes of {approx}300 and {approx}600 AU, for IRAS 22198+6336 and AFGL 5142, respectively, and most likely is tracing protostellar disks rather than flattened envelopes or toroids as is usually found. This is especially clear for the case of IRAS 22198+6336, where we detect a velocity gradient for all the mapped molecules perpendicular to the most chemically rich outflow of the region, yielding a dynamic mass {approx}> 4 M{sub Sun }. As for AFGL 5142, the hot core emission is resolved into two elongated cores separated {approx}1800 AU. A detailed comparison of the complex molecule peaks to the new CO (2-1) data and H{sub 2}O maser data from the literature suggests also that for AFGL 5142 the complex molecules are mainly associated with disks, except for a faint and extended molecular emission found to the west, which is possibly produced in the interface between one of the outflows and the dense surrounding gas.

79 ASTRONOMY AND ASTROPHYSICS↗

Effect of convection on the microstructure of a lamellar eutectic growing with a stepped interface

A two dimensional model developed to study the influence of convective flow on the concentration field ahead of a growing lamellar eutectic is described when one phase projects out into the melt creating a stepped interface. The two dimensional convective flow field, which is periodic in the horizontal direction, was computed numerically using the software FLUENT. The velocity field generated due to the flow of melt over the steps was then incorporated into a finite difference scheme employed to solve the concentration field. The average interfacial composition was calculated and converted to lamellar spacing using the Jackson and Hunt minimum supercooling criterion. It was found that a stepped interface is more sensitive to convection than a planar interface.

Seth, Jayshree↗

Effect of convection on the microstructure of a lamellar eutectic growing with a stepped interface

A two dimensional model developed to study the influence of convective flow on the concentration field ahead of a growing lamellar eutectic is described when one phase projects out into the melt creating a stepped interface. The two dimensional convective flow field, which is periodic in the horizontal direction, was computed numerically using the software FLUENT. The velocity field generated due to the flow of melt over the steps was then incorporated into a finite difference scheme employed to solve the concentration field. The average interfacial composition was calculated and converted to lamellar spacing using the Jackson and Hunt minimum supercooling criterion. It was found that a stepped interface is more sensitive to convection than a planar interface.

Seth, Jayshree↗

Modeling of delamination damage evolution in laminated composites subjected to low velocity impact

This study examines the delamination evolution, under quasi-static conditions, of laminated polymeric composites with mechanically nonlinear resin rich interfaces. The constitutive behavior of the interface is represented by two models developed by Needleman and Tvegaard. These models assumed that the interfacial tractions, a function of only the interfacial displacement, will behave similarly to the interatomic forces generated during the interatomic seperation. The interface material's parameters control the load at which the delamination growth initiates and the final delamination size. A wide range of damage accumulation responses have been obtained by varying the model parameters. These results show that Tvergaard's model has been found to be better suited of the two models in predicting damage evolution for the configurations examined.

Lo, David C.↗

Hyporheic Exchange in Sand Dunes Under a Freely Deforming River Water Surface

Bedform-driven hyporheic exchange is conditioned by the head gradients at the sediment-water interface. Local exchange phenomena between the surface and the subsurface are often driven by the dynamic forces related to the velocity distributions around sediment waves. In open channels, the static forces are represented by the water depth, yet most computational fluid dynamics models use a rigid-lid approximation. Here, we investigated whether and when the deformation of the river’s free-surface influences bedform-driven hyporheic exchange. This was done through simulations of coupled open channel and hyporheic flows with the air-water interface modeled either as a free-surface or a rigid-lid across increasing subcritical Froude numbers from ~0.05 to ~0.95. The normalized hyporheic flux was higher when considering free-surface deformation across most of the range of Froude numbers considered. When the Froude number was larger than 0.6 and smaller than 0.85, both hydrostatic and nonhydrostatic-driven fluxes increased significantly compared to the rigid-lid approach and the total flux was about five times that predicted with the rigid-lid. These results indicate that bedform-driven hyporheic fluxes are underestimated in most studies that use a rigid-lid assumption in subcritical flows.

58 GEOSCIENCES↗

Utah FORGE: Seismic Velocity Models, February 2021

This dataset contains a map, showing the Utah FORGE seismic stations, and seismic velocity model data. There are 61 1-D velocity models which are in a compressed TAR file. A paper is referenced at the end of this description which discusses the use of these data in 3D modelling. The paper summary follows: We expand the application of spatial autocorrelation (SPAC) from typical 1-D Vs profiles to quasi-3-D imaging via Bayesian Monte Carlo inversion (BMCI) using a dense nodal array (49 nodes) located at the Utah Frontier Observatory for Research in Geothermal Energy (FORGE) site. Combinations of 4 and 9 geophones in subarrays provide for 36 and 25 1-D Vs profiles, respectively. Profiles with error bars are determined by calculating coherency functions that fit observations in a frequency range of 0.2-5 Hz. Thus, a high-resolution quasi-3-D Vs model from the surface to 2.0 km depth is derived and shows that surface-parallel sedimentary strata deepen to the west, consistent with a 3-D seismic reflection survey. Moreover, the resulting Vs profile is consistent with a Vs profile derived from distributed acoustic sensing (DAS) data located in a borehole at the FORGE site. The quasi-3-D velocity model shows that the base of the basin dips ~22 degrees to the west and topography on the basement interface coincident with the Mag Lee Wash suggests that the bedrock interface is an unconformity. Reference: Zhang, H. and K. L. Pankow (2021). High-resolution Bayesian spatial auto-correlation (SPAC) pseudo-3D Vs model of Utah FORGE site with a dense geophone array, Geophys. Res. Int, https://doi.org/10.1093/gji/ggab049

15 GEOTHERMAL ENERGY↗

Simulation of detonation of ammonium nitrate fuel oil mixture confined by aluminum: edge angles for DSD

Non-ideal high explosives are typically porous, low-density materials with a low detonation velocity (3--5 km/s) and long detonation reaction zone ({approx} cms). As a result, the interaction of a non-ideal high explosive with an inert confiner can be markedly different than for a conventional high explosive. Issues arise, for example, with light stiff confiners where the confiner can drive the high explosive (HE) through a Prandtl-Meyer fan at the HE/confiner interface rather than the HE driving the confiner. For a non-ideal high explosive confined by a high sound speed inert such that the detonation velocity is lower than the inert sound speed, the flow is subsonic and thus shockless in the confiner. In such cases, the standard detonation shock dynamics methodology, which requires a positive edge-angle be specified at the HE/confiner interface in order that the detonation shape be divergent, cannot be directly utilized. In order to study how detonation shock dynamics can be utilized in such cases, numerical simulations of the detonation of ammonium nitrate-fuel oil (ANFO) confined by aluminum 6061 are conducted.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Analysis of Delamination Growth from Matrix Cracks in Laminates Subjected to Bending Loads

A major source of delamination damage in laminated composite materials is from low-velocity impact. In thin composite laminates under point loads, matrix cracks develop first in the plies, and delaminations then grow from these cracks at the ply interfaces. The purpose of this study was to quantify the combined effects of bending and transverse shear loads on delamination initiation from matrix cracks. Graphite-epoxy laminates with 90 deg. plies on the outside were used to provide a two-dimensional simulation of the damage due to low-velocity impact. Three plate bending problems were considered: a 4-point bending, 3-point bending, and an end-clamped center-loaded plate. Under bending, a matrix crack will form on the tension side of the laminate, through the outer 90 deg. plies and parallel to the fibers. Delaminations will then grow in the interface between the cracked 90 deg. ply and the next adjacent ply. Laminate plate theory was used to derive simple equations relating the total strain energy release rate, G, associated with the delamination growth from a 90 deg. ply crack to the applied bending load and laminate stiffness properties. Three different lay-ups were tested and results compared. Test results verified that the delamination always formed at the interface between the cracked 90 deg. ply and the next adjacent ply. Calculated values for total G sub c from the analysis showed good agreement for all configurations. The analysis was able to predict the delamination onset load for the cases considered. The result indicated that the opening mode component (Mode I) for delamination growth from a matrix crack may be much larger than the component due to interlaminar shear (Mode II).

Murri, G. B.↗

Analysis of delamination growth from matrix cracks in laminates subjected to bending loads

A major source of delamination damage in laminated composite materials is from low-velocity impact. In thin composite laminates under point loads, matrix cracks develop first in the plies, and delaminations then grow from these cracks at the ply interfaces. The purpose of this study was to quantify the combined effects of bending and transverse shear loads on delamination initiation from matrix cracks. Graphite-epoxy laminates with 90 deg plies on the outside were used to provide a two-dimensional simulation of the damage due to low-velocity impact. Three plate bending problems were considered: a 4-point bending, 3-point bending, and an end-clamped center-loaded plate. Under bending, a matrix crack will form on the tension side of the laminate, through the outer 90 deg plies and parallel to the fibers. Delaminations will then grow in the interface between the cracked 90 deg ply and the next adjacent ply. Laminate plate theory was used to derive simple equations relating the total strain energy release rate, G, associated with the delamination growth from a 90 deg ply crack to the applied bending load and laminate stiffness properties. Three different lay-ups were tested and results compared. Test results verified that the delamination always formed at the interface between the cracked 90 deg ply and the next adjacent ply. Calculated values for total G sub c from the analysis showed good agreement for all configurations. The analysis was able to predict the delamination onset load for the cases considered. The result indicated that the opening mode component (Mode I) for delamination growth from a matrix crack may be much larger than the component due to interlaminar shear (Mode II).

Murri, Gretchen Bostaph↗

Heat of mixing and morphological stability

A mathematical model, which incorporates heat of mixing in the energy balance, has been developed to analyze the morphological stability of a planar solid-liquid interface during the directional solidification of a binary alloy. It is observed that the stability behavior is almost that predicted by the analysis of Mullins and Sekerka (1963) at low growth velocities, while deviations in the critical concentration of about 20-25 percent are observed under rapid solidification conditions for certain systems. The calculations indicate that a positive heat of mixing makes the planar interface more unstable, whereas a negative heat of mixing makes it more stable, in terms of the critical concentration.

Nandapurkar, P.↗

Pore‐Scale Modeling of Reactive Transport with Coupled Mineral Dissolution and Precipitation

Abstract We present a new pore‐scale model for multicomponent advective‐diffusive transport with coupled mineral dissolution and precipitation. Both dissolution and precipitation are captured simultaneously by introducing a phase transformation vector field representing the direction and magnitude of the overall phase change. An effective viscosity model is adopted in simulating fluid flow during mineral dissolution‐precipitation that can accurately capture the velocity field without introducing any empirical parameters. The proposed approach is validated against analytical solutions and interface tracking simulations in simplified structures. After validation, the proposed approach is employed in modeling realistic rocks where mineral dissolution and precipitation are dominant at different locations. We have identified three regimes for mineral dissolution‐precipitation coupling: (a) compact dissolution‐precipitation where dissolution is dominant near the inlet and precipitation is dominant near the outlet, (b) wormhole dissolution with clustered precipitation where dissolution generates wormholes in the main flow paths and precipitation clogs the secondary flow paths, and (c) dissolution dominant where all solid grains are gradually dissolved. In the three regimes, the proposed approach provides reliable porosity‐permeability relationships that cannot be described well by traditional macroscale models. We find that the permeability can increase while the overall porosity decreases when the main flow paths are expanded by dissolution and adjacent pore spaces are clogged by precipitation.

58 GEOSCIENCES↗

Confined lattice dynamics of single and quadruple SnSe bilayers in [(SnSe) 1.04 ] m [MoSe 2 ] n ferecrystals

The Sn specific densities of phonon states in the SnSe subunits of [(SnSe) 1.04 ] m [MoSe 2 ] n ferecrystals with (m,n) = (1,1), (4,1) and in bulk SnSe were derived from nuclear inelastic scattering by the 119 Sn M ssbauer resonance. When using different measurement configurations, phonons with polarization parallel and perpendicular to the ferecrystal plane were specifically probed. Vibrational properties and phonon spectral weight are found to strongly depend on the phonon polarization and layer count m. Moreover, a highly peculiar feature of these ferecrystal densities of phonon states is the emergence of rather sharp high energy vibrational modes polarized perpendicular to the ferecrystal plane, which contrasts with usual findings in thin layered structures and nanostructured materials in general, and a depletion of modes with a gap appearing between acoustic and high energy modes. The spectral weight of these phonons depends on the overall SnSe content, m, but cannot be unambiguously attributed to SnSe MoSe 2 interfaces. Considering the low energy part of lattice dynamics, ferecrystals exhibit rather low average phonon group velocities as compared to the speed of sound in the long wavelength limit. For the (1,1) ferecrystal, this effect is most pronounced for vibrations polarized in the ferecrystal plane. Therefore, an experimental microscopic origin for the vibrational and bonding anisotropy in subunits of ferecrystals is provided.

36 MATERIALS SCIENCE↗

Investigation of magnetic flux transport and shock formation in a staged Z-pinch

Target preheating is an integral component of magnetized inertial fusion in reducing convergence ratio. In the staged Z-pinch concept, it is achieved via one or more shocks. Previous work [Narkis et al., Phys. Plasmas 23, 122706 (2016)] found that shock formation in the target occurred earlier in higher-Z liners due to faster flux transport to the target/liner interface. However, a corresponding increase in magnitude of magnetic pressure was not observed, and target implosion velocity (and therefore shock strength) remained unchanged. To investigate other means of increasing the magnitude of transported flux, a Korteweg-de Vries-Burgers equation from the 1-D single-fluid, resistive magnetohydrodynamic equations is obtained. Solutions to the nondispersive (i.e., Burgers) equation depend on nondimensional coefficients, whose dependence on liner density, temperature, etc., suggests an increase in target implosion velocity, and therefore shock strength, can be obtained by tailoring the mass of a single-liner gas puff to a double-liner configuration. In the selected test cases of 1-D simulated implosions of krypton on deuterium, the peak Mach number increased from ∼5 to ∼8. While a notable increase was seen, Mach numbers exceeding 10 (implosion velocities exceeding ∼25 cm/μs) are necessary for adequate shock preheating.

Narkis, J. (ORCID:0000000154368933)↗

OBSERVATIONS OF SUBARCSECOND BRIGHT DOTS IN THE TRANSITION REGION ABOVE SUNSPOTS WITH THE INTERFACE REGION IMAGING SPECTROGRAPH

Observations with the Interface Region Imaging Spectrograph (IRIS) have revealed numerous sub-arcsecond bright dots in the transition region above sunspots. These bright dots are seen in the 1400 Å and 1330 Å slit-jaw images. They are clearly present in all sunspots we investigated, mostly in the penumbrae, but also occasionally in some umbrae and light bridges. The bright dots in the penumbrae typically appear slightly elongated, with the two dimensions being 300-600 km and 250-450 km, respectively. The long sides of these dots are often nearly parallel to the bright filamentary structures in the penumbrae but sometimes clearly deviate from the radial direction. Their lifetimes are mostly less than one minute, although some dots last for a few minutes or even longer. Their intensities are often a few times stronger than the intensities of the surrounding environment in the slit-jaw images. About half of the bright dots show apparent movement with speeds of ∼10-40 km s{sup –1} in the radial direction. Spectra of a few bright dots were obtained and the Si IV 1402.77 Å line profiles in these dots are significantly broadened. The line intensity can be enhanced by one to two orders of magnitude. Some relatively bright and long-lasting dots are also observed in several passbands of the Atmospheric Imaging Assembly onboard the Solar Dynamics Observatory, and they appear to be located at the bases of loop-like structures. Many of these bright dots are likely associated with small-scale energy release events at the transition region footpoints of magnetic loops.

79 ASTRONOMY AND ASTROPHYSICS↗

Quantifying sampling noise and parametric uncertainty in atomistic-to-continuum simulations using surrogate models

We present a methodology to assess the predictive fidelity of multiscale simulations by incorporating uncertainty in the information exchanged between the components of an atomistic-to-continuum simulation. We account for both the uncertainty due to finite sampling in molecular dynamics (MD) simulations and the uncertainty in the physical parameters of the model. Using Bayesian inference, we represent the expensive atomistic component by a surrogate model that relates the long-term output of the atomistic simulation to its uncertain inputs. We then present algorithms to solve for the variables exchanged across the atomistic-continuum interface in terms of polynomial chaos expansions (PCEs). We also consider a simple Couette flow where velocities are exchanged between the atomistic and continuum components, while accounting for uncertainty in the atomistic model parameters and the continuum boundary conditions. Results show convergence of the coupling algorithm at a reasonable number of iterations. As a result, the uncertainty in the obtained variables significantly depends on the amount of data sampled from the MD simulations and on the width of the time averaging window used in the MD simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical modeling of HgCdTe solidification: Effects of phase diagram, double-diffusion convection and microgravity level

A numerical model of HgCdTe solidification was implemented using finite the element code FIDAP. Model verification was done using both experimental data and numerical test problems. The model was used to evaluate possible effects of double-diffusion convection in molten material, and microgravity level on concentration distribution in the solidified HgCdTe. Particular attention was paid to incorporation of HgCdTe phase diagram. It was found, that below a critical microgravity amplitude, the maximum convective velocity in the melt appears virtually independent on the microgravity vector orientation. Good agreement between predicted interface shape and an interface obtained experimentally by quenching was achieved. The results of numerical modeling are presented in the form of video film.

Bune, Andris V.↗

Cpt 2.0: A 2-D Fluid Visualization Program for Unsteady Data

Cpt is an interactive two dimensional fluid visualization program for unsteady data sets. Cpt is capable of showing the velocity and scalar fields, calculating streaml@nes and contours, advecting particles, bubblers and more. The user interface is simple point and click and most of its operations are deducible from a few minutes of experimentation.

Levit, Creon↗