Search NASA⌕ Search

SEARCH · Search NASA

Results for “materials reliability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Infrared nanospectroscopy characterization of metal oxide photoresists

Implementation of extreme ultraviolet (EUV) lithography in high-volume semiconductor manufacturing requires a reliable and scalable EUV resist platform. A mechanistic understanding of the pros and cons of different EUV resist materials is critically important. However, most material characterization methods with nanometer resolution use an x-ray photon or electron beam as the probe, which often cause damage to the photoresist film during measurement. Here, we illustrated the use of non-destructive infrared nanospectroscopy [or nano-Fourier-Transform infrared spectroscopy (nano-FTIR)] to obtain spatially resolved composition information in patterned photoresist films. Further, clear evidence of exposure-induced chemical modification was observed at a spatial resolution down to 40 nm, well below the diffraction limit of infrared light. With improvements, such a nano-FTIR technique with nanoscale spatial resolution, chemical sensitivity, and minimal radiation damage can be a promising candidate for the fundamental study of material properties relevant to EUV lithography.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Halide Perovskite Solar Photovoltaics

Technological progress in photovoltaic (PV) technologies provides hope that a comprehensive and desperately needed decarbonization of the energy sector is possible. Commercially successful PV technologies based predominantly on silicon wafer technology are reliable and cost-effective, but remain capital- and carbon-intensive. In this context, emerging PV technologies, such as metal-halide perovskites (MHPs), could further catalyze the energy transition by providing technological opportunities for even lower-cost, mass-producible, high-efficiency solar cells with a significantly reduced "carbon footprint." This themed issue of MRS Bulletin on "Halide perovskite solar photovoltaics summarizes the current state of the art, challenges, and opportunities of perovskite photovoltaics with contributions and perspectives from six expert teams worldwide. The topics covered provide a status update on perovskite PV, remaining hurdles to their deployment, and challenges to realizing the potential of this technology to impact climate goals. Articles in this collection address scalability of perovskite PV and prospects for industrial manufacturing; perovskite PV as an add-on technology on top of commercial silicon PV; environmental and sustainability considerations; and durability and reliability considerations. Further considerations include prospects of automation, coupled to artificial intelligence and machine learning, for accelerating material-based solutions to these outstanding challenges including the possibilities of discovering new absorber and device component materials to enable success and ultimately deployment of these next-generation PVs.

metal-halide perovskites↗
DOE OSTI2024

Decarbonizing Cooking Appliances With Hydrogen

A novel hydrogen compatible heterogeneous burner prototype was engineered, fabricated, and evaluated for applications in cooking appliances. The key features targeted and accomplished under this effort included fuel flexibility, tolerance to high hydrogen concentrations (up to 85% in atmospheric design and 100% in premixed design), wide range of thermal power ratings, thermal cycling, reliability, and most importantly safety. The burner was operated in the range of 3000 – 12,000 Btu/h under all practical operating conditions (cold start, hot restart, fuel concentration variance). The heterogeneous oxidation burner technology was evaluated for overall performance targeting safety, reliability, emissions, fuel flexibility, and energy efficiency in a commercial RV and residential cooking range appliance prototypes. The burner demonstrated safe and reliable performance generating infrared heating energy without the consumption of any parasitic energy while using low-cost materials. Performance evaluation testing of the novel IR burner demonstrated fuel flexibility with hydrogen blended natural gas while significantly eliminating air pollutants like NOx and methane and increasing the energy efficiency by up to 20%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Enhancing Lifetime and Reducing Costs for Fish Diversion Netting Structures (Final Report)

In this effort Pacific Northwest National Laboratory (PNNL) developed and demonstrated an anti-fouling coating that is effective on fish diversion structures. The coating was based on a previously developed superhydrophobic lubricant infused composite (SLIC) coating but modified for application to flexible substrates. We showed that the new reformulated coating – FlexiSLIC – can be applied to flexible fibrous structures to significantly reduce biofouling of netting and anchor lines, to enable longer operational lifetimes, reduced costs, and more reliable operations. The coating developed in this effort was tested on relevant fish diversion structural netting and rope materials (e.g. nylon, Dyneema, polypropylene) to reduce biofouling. Engagement with industry in the development and demonstration further supported progress toward commercialization of the materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

An Innovative High Throughput Genome Releaser for Rapid and Efficient PCR Screening

High-throughput PCR screening is vital in synthetic biology and metabolic engineering as it allows researchers to rapidly analyze and detect numerous targeted genetic mutation in the genome. Current challenges for high-throughput PCR screening in synthetic biology include efficiently preparing genomic DNA, optimizing protocols for diverse sample types, managing contamination risks, and effectively analyzing the large volumes of data generated while ensuring consistent and accurate results. In this study, we present the development of a High Throughput Genome Releaser (HTGR), an innovative device addressing common challenges in screening PCR. This genome DNA releaser is designed based on a squash method for rapid, cost-effective, and efficient DNA release, optimized for subsequent PCR reactions. After experimenting with various synthetic materials, we selected a plastic that closely replicates the smooth surface and compression properties of microscope slides, ensuring reliable performance. We engineered a device featuring a 96-Well Plate and a shear applicator, operable both manually and automatically, and compatible with standard liquid-handling robot platform. This compatibility enhances ease of use in high-throughput PCR workflows. Additionally, we developed software to support its automatic functions. Our results demonstrated that the specially engineered 96-Well Plate and HTGR can effectively squash fungal spores , which release enough genome DNA for PCR screening. The genome releaser facilitates the preparation of PCR-amplifiable genomic DNA substrate from 96 samples within minutes, eliminates the need for extraction buffers, and is adaptable to a wide range of microorganisms and cells, which could significantly advance biomanufacturing processes.

Yuan, Guoliang [BATTELLE (PACIFIC NW LAB)]↗
DOE OSTI2024

ASME – Grappling with the Concept of Component Failure

ASME concepts of component failure. Definition for failure, functionality, damage tolerance, including Magnox reactors and AGRs. How ASME is addressing damage tolerance, and Section III division 5 Design, Classification, Reliability Target for SRC-1 components, Basic analysis approach, simple assessment, and full assessments, Reference to reliability and integrity management and strategy for graphite components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Testing and Characterization to Develop a Mechanistic Explanation for Unsaturated Drift of Fiber Optic Sensors during High-Dose Irradiation

The primary limitation for any optical fiber-based sensor for nuclear reactor applications is radiation-induced attenuation (RIA) of the transmitted and/or reflected signals. Based on several recent studies, RIA is tolerable for some fused silica optical fibers with the proper choice of sensing wavelength and fiber dopants. For extreme temperature applications (> 1000°C), sapphire optical fibers have been proposed; however, recent optical transmission measurements performed on bulk sapphire samples showed prohibitively large RIA. For some sensors, radiation-induced dimensional changes in the fiber materials can also cause significant drift. Moreover, the drift that was observed in numerous experiments performed in the High Flux Isotope Reactor (HFIR), the Advanced Test Reactor, the Massachusetts Institute of Technology Reactor, and other international facilities far exceeded what would be expected based on compaction of fused silica glass. Clearly, additional work is needed to better understand the origins of both RIA and radiation-induced drift in both silica and sapphire optical fiber-based sensors before these sensors can be reliably deployed for nuclear applications. This work evaluated the underlying mechanisms that may be responsible for RIA and drift in silica and sapphire materials. First, detailed characterization was performed on bulk fused silica glass samples that were previously irradiated to different neutron fluences at different temperatures to better understand the structural changes that drive radiation-induced drift in the absence of coating effects that are discussed later. Results show that the non-monotonic compaction that occurs with increasing neutron fluence continues up to fast neutron fluences approaching 10 22 n/cm 2 , which has important implications for physics-based models that may be used to compensate for the sensor drift. Initial Raman spectroscopy and synchrotron x-ray diffraction provide insights into the nature of the structural changes. Next, detailed characterizations were performed on silica fibers with various coatings that were subjected to several different thermal treatments. The hypothesis is that the coatings convert to carbon-rich materials that compact under irradiation, putting a large compressive strain on the fiber. Out-of-pile testing confirms that both polyimide and acrylate fiber coatings convert to glassy carbon (GC) materials when heated under inert conditions, and the degree of order (i.e., graphitization) increases with increasing temperature. The results provide increasingly strong evidence that the combination of polymeric coatings and inert (or vacuum) conditions render fiber optic sensors susceptible to significant radiation-induced drift that would not otherwise exist in uncoated fibers. Finally, transmission electron microscopy was performed on bulk sapphire samples that were irradiated to two neutron fluences at different temperatures to gain insights into the potential mechanisms driving the prohibitive RIA at higher neutron fluences and temperatures. Contrary to previous hypotheses, results show that scattering from radiation-induced voids cannot explain the observed RIA. Similarly, models for scattering losses from dislocation loops also do not agree with the experimental results. Instead, fitting to the experimental data shows that increased absorption from aluminum vacancy centers is the most likely explanation for the the prohibitively large RIA that was observed at high irradiation temperature and dose. In addition, the voids that formed in these single-crystal samples were found to align along the basal plane (a-axis) as opposed to that seen in previous observations of c-axis alignment in polycrystalline samples, which could have important implications for anisotropic swelling and other phenomena that could affect sensor performance at high neutron fluence.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Testing and Characterization to Develop a Mechanistic Explanation for Unsaturated Drift of Fiber Optic Sensors during High-Dose Irradiation

The primary limitation for any optical fiber-based sensor for nuclear reactor applications is radiation-induced attenuation (RIA) of the transmitted and/or reflected signals. Based on several recent studies, RIA is tolerable for some fused silica optical fibers with the proper choice of sensing wavelength and fiber dopants. For extreme temperature applications (> 1000°C), sapphire optical fibers have been proposed; however, recent optical transmission measurements performed on bulk sapphire samples showed prohibitively large RIA. For some sensors, radiation-induced dimensional changes in the fiber materials can also cause significant drift. Moreover, the drift that was observed in numerous experiments performed in the High Flux Isotope Reactor (HFIR), the Advanced Test Reactor, the Massachusetts Institute of Technology Reactor, and other international facilities far exceeded what would be expected based on compaction of fused silica glass. Clearly, additional work is needed to better understand the origins of both RIA and radiation-induced drift in both silica and sapphire optical fiber-based sensors before these sensors can be reliably deployed for nuclear applications. This work evaluated the underlying mechanisms that may be responsible for RIA and drift in silica and sapphire materials. First, detailed characterization was performed on bulk fused silica glass samples that were previously irradiated to different neutron fluences at different temperatures to better understand the structural changes that drive radiation-induced drift in the absence of coating effects that are discussed later. Results show that the non-monotonic compaction that occurs with increasing neutron fluence continues up to fast neutron fluences approaching 10 22 n/cm 2 , which has important implications for physics-based models that may be used to compensate for the sensor drift. Initial Raman spectroscopy and synchrotron x-ray diffraction provide insights into the nature of the structural changes. Next, detailed characterizations were performed on silica fibers with various coatings that were subjected to several different thermal treatments. The hypothesis is that the coatings convert to carbon-rich materials that compact under irradiation, putting a large compressive strain on the fiber. Out-of-pile testing confirms that both polyimide and acrylate fiber coatings convert to glassy carbon (GC) materials when heated under inert conditions, and the degree of order (i.e., graphitization) increases with increasing temperature. The results provide increasingly strong evidence that the combination of polymeric coatings and inert (or vacuum) conditions render fiber optic sensors susceptible to significant radiation-induced drift that would not otherwise exist in uncoated fibers. Finally, transmission electron microscopy was performed on bulk sapphire samples that were irradiated to two neutron fluences at different temperatures to gain insights into the potential mechanisms driving the prohibitive RIA at higher neutron fluences and temperatures. Contrary to previous hypotheses, results show that scattering from radiation-induced voids cannot explain the observed RIA. Similarly, models for scattering losses from dislocation loops also do not agree with the experimental results. Instead, fitting to the experimental data shows that increased absorption from aluminum vacancy centers is the most likely explanation for the the prohibitively large RIA that was observed at high irradiation temperature and dose. In addition, the voids that formed in these single-crystal samples were found to align along the basal plane (a-axis) as opposed to that seen in previous observations of c-axis alignment in polycrystalline samples, which could have important implications for anisotropic swelling and other phenomena that could affect sensor performance at high neutron fluence.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Dislocation density in fine grain-size spark-plasma sintered aluminum measured using high brightness synchrotron radiation

In this study, three-dimensional orientation mapping of samples of aluminum prepared by spark plasma sintering (SPS) with average grain sizes of 5 μm and 1 μm has been carried out using high-brightness synchrotron radiation, from which the geometrically necessary dislocation (GND) density has been determined. The low average measured GND density values confirm that the SPS process can be used to produce samples containing grains with dislocation density similar to that of fully recrystallized coarse-grained samples. Values of GND density are also compared to those obtained from electron back-scatter diffraction studies on the same material, highlighting the significantly higher angular resolution of the synchrotron data. For the 5 μm grain-size sample the measured GND density can account for a large fraction of the previously observed positive Hall-Petch deviation of this material. For the 1 μm grain-size sample, however, the GND-based strengthening contribution is much smaller than the reported positive Hall-Petch deviation, such that the additional strength may be reliably associated with dislocation source-limited strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multireference diffusion Monte Carlo reaches 2D materials

Abstract Quantum confinement in 2D materials strongly enhances electronic correlation effects. Therefore, predicting the properties of these unique materials, with both a high level of accuracy and computational efficiency, without relying on adjustable parameters or functionals, remains an outstanding theoretical challenge. The majority of theoretical studies are based on the approximations of density functional theory (DFT). The reliability of DFT predictions are heavily dependent on the choice of an approximated exchange-correlation functional. Here, we estimate the magnitude of impact of correlation on the total energy for the quintessential 2D material, graphene, by performing and comparing state-of-the-art selected CI and quantum Monte Carlo extrapolated calculations for a single unit cell at the$$\Gamma$$point. We demonstrate that Self-Healing Diffusion Monte Carlo (SHDMC) obtains a very compact, but high-quality wavefunction for this system that lacks the strong basis set dependence displayed by state of the art quantum chemistry methods. The SHDMC wavefunction is of higher quality compared to that obtained from sCI, in the same orbital basis, while being$$\sim$$ 1000 times smaller in terms of determinant count compared to sCI. We also demonstrate that extrapolating SHDMC results to the infinite determinant limit compares extremely well with complete basis set extrapolated sCI. Our work paves the way for future validation of SHDMC applied to challenging 2D materials.

Science & Technology - Other Topics↗
DOE OSTI2023

Pair distribution function analysis of discrete nanomaterials in PDFgui

Pair distribution functions (PDFs) are a leading tool for atomic structure analysis of nanomaterials. However, the most widely used programs for refining atomic structure against PDF data are based on extended crystallographic models, which cannot be applied to discrete, whole nanoparticles. Furthermore, this work describes a straightforward approach to simulate and refine atomistic models of discrete clusters and nanoparticles employing widely used PDF modelling programs such as PDFgui that utilize extended crystallographic models. In this approach, the whole particle to be modelled is contained within an expanded, and otherwise empty, unit cell that is sufficiently large to avoid correlations between atoms in neighbouring unit cells over the r range analyzed. The PDF of the particle is simulated as a composite using two conventional `phases': one that calculates the atom–atom correlations and one that approximates the local number density. This approach is first validated for large nanoparticles that are well modelled by a conventional shape factor model, and then applied to simulate the PDF of discrete particles and low-dimensional materials (graphene and MXene) and to model the experimental PDF data for single-layer FeS nanosheets. A comparison of this approach with the DiffPy-CMI program, which calculates the PDF of discrete species, shows that the composite modelling approach is equally or more accurate. Example input files for implementing this approach within PDFgui and TOPAS, and recommendations for selecting model parameters for reliable application of this refinement strategy, are provided.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Analysis of the dependence of critical electric field on semiconductor bandgap

Abstract Understanding of semiconductor breakdown under high electric fields is an important aspect of materials’ properties, particularly for the design of power devices. For decades, a power-law has been used to describe the dependence of material-specific critical electrical field ( $${\mathcal{E}}_{\text{crit}}$$ E crit ) at which the material breaks down and bandgap ( E g ) . The relationship is often used to gauge tradeoffs of emerging materials whose properties haven’t yet been determined. Unfortunately, the reported dependencies of $${\mathcal{E}}_{\text{crit}}$$ E crit on E g cover a surprisingly wide range in the literature. Moreover, $${\mathcal{E}}_{\text{crit}}$$ E crit is a function of material doping. Further, discrepancies arise in $${\mathcal{E}}_{\text{crit}}$$ E crit values owing to differences between punch-through and non-punch-through device structures. We report a new normalization procedure that enables comparison of critical electric field values across materials, doping, and different device types. An extensive examination of numerous references reveals that the dependence $${\mathcal{E}}_{\text{crit}}$$ E crit ∝ E g 1.83 best fits the most reliable and newest data for both direct and indirect semiconductors. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2020

AFIP6-MkII and RERTR-12 Porosity Data Collection and Analysis for Modeling and Simulation

Gathering data for the improvement of nuclear fuel modeling and simulation efforts is the primary driver for this work. Mechanistic models allow for a better understanding of the material on a micro- and macrostructural level while saving time and money over traditional experiment efforts. Historically, summarized data and correlations are the inputs for empirical material models and model validation. When improving these models for nuclear fuels with experimental results, there is a lack of reliable data readily available. Experiments - RERTR-12 and AFIP6-MkII - were conducted to understand the irradiation behavior of metallic U-10Mo monolithic fuels for use in extreme reactor environments such as research reactors like the Advanced Test Reactor (ATR) or the High Flux Isotope Reactor (HFIR). Microstructural characteristics of fission gas pores (FGP) in each experiment are collected using an automated image analysis technique developed at the University of Florida and presented here. A series of statistical tests are performed to explore the reliability of the results, as well as understand where the data is lacking and what future data collection is necessary to provide sufficient information to assist modeling efforts. The focus is on the porosity, pore size, and eccentricity of FGPs formed during irradiation in three AFIP6-MkII samples and one RERTR-12 sample. From the analysis, it is clear there are substantial impacts of fission density on the pore structure, but there also exist also underlying connections between each sample and the behavior observed in the pores. Further analyses of the pre- and post-irradiation microstructure are needed to improve the understanding of these connections. An early method for microstructural data analysis is presented within and is currently being expanded to include other microstructure data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Driving Zn-MnO2 grid-scale batteries: A roadmap to cost-effective energy storage

Highlights Zn-MnO 2 batteries promise safe, reliable energy storage, and this roadmap outlines a combination of manufacturing strategies and technical innovations that could make this goal achievable. Approaches such as improved efficiency of manufacturing and increasing active material utilization will be important to getting costs as low as $100/kWh, but key materials innovations that facilitate the full 2-electron capacity utilization of MnO 2 , the use of high energy density 3D electrodes, and the promise of a separator-free battery with greater than 2V potential offer a route to batteries at $50/kWh or less. Abstract Large-scale energy storage is certain to play a significant, enabling role in the evolution of the emerging electrical grid. Battery-based storage, while not a dominant form of storage today, has opportunity to expand its utility through safe, reliable, and cost-effective technologies. Here, secondary Zn–MnO 2 batteries are highlighted as a promising extension of ubiquitous primary alkaline batteries, offering a safe, environmentally friendly chemistry in a scalable and practical energy dense technology. Importantly, there is a very realistic pathway to also making such batteries cost-effective at price points of $50/kWh or lower. By examining manufacturing examples at the Zn–MnO 2 battery manufacturer Urban Electric Power, a roadmap has been created to realize such low-cost systems. By focusing on manufacturing optimization through reduced materials waste, scalable manufacturing, and effective materials selection, costs can be significantly reduced. Ultimately, though, coupling these approaches with emerging research and development advances to enable full capacity active materials utilization and battery voltages greater than 2V are likely needed to drive costs below a target of $50/kWh. Reaching this commercially important goal, especially with a chemistry that is safe, well-known, and reliably effective stands to inject Zn–MnO 2 batteries in the storage landscape at a critical time in energy storage development and deployment. Graphical abstract

Spoerke, Erik D. (ORCID:0000000322862560)↗
DOE OSTI2022

The Trajectory of Additively Manufactured Titanium Alloys with Superior Mechanical Properties and Engineered Microstructures

Additive manufacturing (AM) plays a crucial role in the manufacturing and development of advanced materials including titanium alloys for engineering applications. During the last two decades, a great deal of effort has been devoted to print titanium parts with desired properties. However, due to presence of non-equilibrium/metastable phases, anisotropic microstructure, and various porosities in the printed titanium alloys, achieving an excellent combination of mechanical properties has been challenging. Here this review paper aims to provide a comprehensive overview of multiple post-process and in-process approaches to achieve enhanced strength-ductility combinations by microstructure engineering. Approaches such as addition of alloying elements/nucleants, multi-step post heat treatment, in-situ heat treatment, forced inter-pass cooling, in situ peening/rolling, hybridizing microstructure, high-intensity acoustic vibration, thermo-hydrogen refinement of microstructure, deliberately introducing lack of fusion defects with subsequent hot isostatic pressing are discussed in detail. Finally, we conclude by highlighting the challenges associated with each method and potential areas of improvement that can pave the way to develop reliable components with enhanced performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Local Lattice Deformation of Tellurene Grain Boundaries by Four-Dimensional Electron Microscopy

Two-dimensional (2D) tellurene is a promising competitor for the fabrication of ultrathin optoelectronic devices belonging to a new family of monoelemental 2D materials. Furthermore, the precise fabrication and characterization of tellurene and its lattice defects is of utmost importance to determine device reliability and predict functionality, yet it remains experimentally challenging. The rapid growth of the four-dimensional scanning transmission electron microscopy (4D-STEM) technique as well as postprocessing tools now allows for structural analysis with nanometer-scale resolution over a broad range of length scales. Here, we use 4D-STEM to reveal the three-dimensional (3D) atomic structure of the characteristic grain boundary in 2D tellurium formed through a new microwave-enabled chemical self-assembly. Strain and lattice parameter maps permit the reconstruction of the roughness of the grain boundary and suggest that its formation is promoted by a wedge of helical atomic chains along the [0001] crystallographic direction. The observation of wrinkles at the grain boundary is found to be the dominant relaxation mechanism. Insights into the formation mechanism are elucidated by mapping the lattice parameters as the first demonstration of local in-plane and out-of-plane unit cell variation in a nanometer-by-nanometer real-space array.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Distribution Development for the RDX Regional Model at Los Alamos National Laboratory - 20385

Representing uncertainty in model inputs often means finding a balance between uncertainty and physical reality. Developing wide distributions may seem conservative in principle, but this approach may lead to unrealistic model results. Characterizing the current state of knowledge of stochastic inputs presents many challenges, especially if the data available are limited or have limited relevance to the site. Relationships among these inputs may also be important to represent but are typically complex or difficult to define. Often special adjustments must be made to account for reduced credibility in particular data. If parameters are strongly related to one another, a correlation structure may be developed for input to the model. Other techniques such as regression models may be used to incorporate relationships between the information available and the desired parameters. The process of developing distributions must consider details of the model in terms of what the distribution is meant to represent. This paper uses the example of a probabilistic fate and transport model for hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in the regional aquifer at Los Alamos National Laboratory (LANL). For many parameters, a single draw is applied to all space and time over which the model is run, for a single iteration. This simplification is often made for many reasons, and can often be beneficial, but also adds additional complexity in the distribution development process. Defining the distributional goals as they relate to the modeling process is an important step, which should take place prior to evaluation of the data. Usually, the distributions developed are meant to characterize the average value of the parameter over the spatial and temporal domain of the model. Distribution development requires consideration of many sources of information on the parameter where available, ideally from multiple references. Examples of different sources include data from different references but also from different conditions, measurement methods, or experimental types. Depending on these conditions and the reliability or relevance of particular references, different sources of data may each contribute valuable information but have varying relevance to the site. In these cases, weighting data unequally is a useful way to incorporate this information. As an example, aqueous dispersivity data are available for a variety of rock types. Only a few values are available for the desired rock type, and this is not enough to develop a distribution. Therefore, dispersivity values from other rock types are included in distribution development but are down-weighted such that the best data have the most influence on the distribution developed. In another case, K{sub d} distributions in the model are meant to represent a known composition of multiple soil types. Data from these materials are weighted accordingly to develop a distribution for the weighted average K{sub d} across soil types. Other cases include varying reliability of different sources, and weighting data according to the confidence in these sources. In some cases, input parameters are correlated with one another. An example is advective porosity, which is positively correlated with total porosity and must be less than total porosity. Paired data with both parameters must exist to discern the relationship between the two parameters and if it is necessary to build a correlation structure into the model. In general, correlated parameters may be represented in the model by a multivariate distribution, or perhaps more desirably, capturing the correlation within the developed distributions which may be treated as independent from one another. In the example of porosity, this can be done by transforming advective porosity into a proportion of total porosity which may be drawn independently from the distribution of total porosity. This paper explores how complex data and correlations can be incorporated to meet the distributional goals of the model, using the RDX regional model as a detailed example. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Raman scattering of rhenium for secondary pressure calibration

With the increasing number of 100 s GPa experiments in the diamond anvil cell (DAC), improved accuracy in secondary pressure calibrations to extreme pressures is essential. The rhenium equation of state has been proposed as a pressure calibrant via x-ray diffraction with potentially broad applications as it is commonly used as a gasket material in DAC experiments. In this work, we conducted Raman spectroscopy experiments on rhenium in the DAC and report the pressure shift of the E2g mode, a refined high-pressure C44 and mode-Grüneisen parameter above 200 GPa. We used flat, beveled, and toroidal diamond anvils under quasi-hydrostatic and non-hydrostatic conditions. By measuring the E2g mode from the culet edge to the center, we analyzed pressure distribution based on culet type and distance from the anvil center. The shift in the E2g mode can be expressed as a function of pressure, and diamond edge measurements appear reliable across all anvil types. Comparing the center and edge pressures reveals anvil cupping, offering insights into predicting or preventing anvil failure during materials properties measurements at extreme conditions.

Diamond anvil cells↗