Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

Energetic Condensation Growth of Nb Thin-Films for SRF Applications

AASC, JLab and NSU conduct research into SRF thin-film coatings by first characterizing properties such as morphology, grain size, crystalline structure, defects, and impurities, then measuring Tc and RRR, and following this with ?in-cavity? RF measurements of the Surface Impedance of the films at cryogenic temperatures. These progressive steps are essential to eventual design and measurement of SRF accelerator structures at high fields. We have recently produced Nb superconducting thin-films with crystal grain sizes ~50?m using our proprietary CED^TM cathodic arc technique. RRR of ~129 at Tc of 9.2K was measured in a film grown on a-plane sapphire heated to 400oC. At 20oC, the RRR dropped to ~4. Energetic condensation using cathodic arcs produces non-equilibrium fast ions (~50-100eV). These ion energies are much higher than typical sputtering energies. When such energetic condensation is complemented by substrate biasing (to ~200-300eV) the incident ion energy is further increased, allowing growth modes that would otherwise require much higher substrate temperatures. Data are presented for pure Nb films using SEM, EBSD, XRD and a Surface Impedance Characterization RF cavity.

Krishnan, Mahadevan↗

Controlled RAFT Polymerization of 2-Vinyl-4,4-Dimethylazlactone (VDMA): A Facile Route to Bio-Inspired Polymer Surfaces

We report the controlled radical polymerization of 2-vinyl-4,4-dimethyl azlactone (VDMA), a 2-alkenyl-2-oxazolin-5-one monomer that contains a polymerizable vinyl moiety as well as a highly reactive, pendant azlactone as well as solution characterizations and surface attachment and functionaliztion. Reversible addition fragmentation chain transfer (RAFT) was used to polymerize of VDMA in benzene at 65 C using either 2-(2-cyanopropyl) dithiobenzoate (CPDB) or 2-dodecylsulfanylthiocarbonyl-sulfanyl-2-methylpropionic acid (DMP) as RAFT chain transfer agents (CTAs). The pseudo first order kinetics and resultant well-defined polymers of low polydispersity indicate that both CTAs afford control over the RAFT polymerization of VDMA. Dynamic and static light scattering and small angle neutron scattering were performed to determine the dn/dc, weight-average molecular weight, radius of gyration, and second virial coefficient of VDMA homopolymers in THF. Additionally, well-defined polymers of VDMA containing carboxyl end groups were covalently attached to epoxy modified silicon wafers via esterification to produce polymeric scaffolds that could be subsequently functionalized for various bio-inspired applications.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Efficiency of inhibitor for biocorrosion influenced by consortium sulfate reducing bacteria on carbon steel

The inhibition efficiency of benzalkonium chloride (BKC) in controlling biocorrosion on the carbon steel surfaces has been investigated. The carbon steel coupons were incubated in the presence of consortium SRB (C-SRB) with and without BKC for the difference medium concentration. The corrosion rate and inhibition efficiency have been evaluated by a weight loss method. The morphology of biofilm C-SRB on the steel surfaces were characterized with variable pressure scanning electron microscopy (VPSEM). The results revealed that BKC exhibits a low corrosion rate, minimizing the cell growth and biofilm development on the carbon steel surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vapor-phase grafting of functional silanes on atomic layer deposited Al 2 O 3

Fundamental studies are needed to advance our understanding of selective adsorption in aqueous environments and develop more effective sorbents and filters for water treatment. Vapor-phase grafting of functional silanes is an effective method to prepare well-defined surfaces to study selective adsorption. In this investigation, we perform vapor phase grafting of five different silane compounds on aluminum oxide (Al2O3) surfaces prepared by atomic layer deposition. These silane compounds have the general formula L3Si–C3H6–X where the ligand, L, controls the reactivity with the hydroxylated Al2O3 surface and the functional moiety, X, dictates the surface properties of the grafted layer. We study the grafting process using in situ Fourier transform infrared spectroscopy and ex situ x-ray photoelectron spectroscopy measurements, and we characterize the surfaces using scanning electron microscopy, atomic force microscopy, and water contact angle measurements. Here, we found that the structure and density of grafted aminosilanes are influenced by their chemical reactivity and steric constraints around the silicon atom as well as by the nature of the anchoring functional groups. Methyl substituted aminosilanes yielded more hydrophobic surfaces with a higher surface density at higher grafting temperatures. Thiol and nitrile terminated silanes were also studied and compared to the aminosilane terminated surfaces. Uniform monolayer coatings were observed for ethoxy-based silanes, but chlorosilanes exhibited nonuniform coatings as verified by atomic force microscopy measurements.

36 MATERIALS SCIENCE↗

Analysis of the Surface Morphology and Chemical Composition of Zr-Nb3Sn Alloys with Zr Different Concentrations

The inclusion of zirconium (Zr) in niobium-tin (Nb3Sn) significantly enhances the performance of Nb3Sn radiofrequency cavities in high magnetic fields. This research project is dedicated to characterizing the surface properties and chemical composition of Zr-doped Nb3Sn. Two different concentrations of Zr were used for doping: approximately 0.5% and 24%. Various spectroscopy techniques were employed to analyze how the surface morphology and chemical composition of Nb3Sn change with increasing Zr content. The findings of this study indicate that the grain size decreases as the Zr concentration increases. In samples with 24% Zr, nanometer-sized particles, likely oxides, were observed. X-ray photoelectron spectroscopy (XPS) data revealed that the thickness of niobium oxides (NbOx) decreases with increasing Zr, while the thickness of tin oxides (SnOx) increases. Additionally, grain size distribution analysis showed that the average grain size is around 5300 nm , with a grain area density of about 165 grains/μm .

Sue, Micah↗

Coherent Acoustic Interferometry during the Photodriven Oxygen Evolution Reaction Associates Strain Fields with the Reactive Oxygen Intermediate (Ti–OH*)

The oxygen evolution reaction (OER) from water requires the formation of metastable, reactive oxygen intermediates to enable oxygen–oxygen bond formation. Conversely, such reactive intermediates could also structurally modify the catalyst. Here, a descriptor for the overall catalytic activity, the first electron and proton transfer OER intermediate from water, (M–OH*), has been associated with significant distortions of the metal–oxygen bonds upon charge-trapping. Time-resolved spectroscopy of in situ, photodriven OER on transition metal oxide surfaces has characterized M–OH* for the charge trapping and the symmetry of the lattice distortions by optical and vibrational transitions, respectively, but had yet to detect an interfacial strain field arising from a surface coverage M–OH*. Here, we utilize picosecond, coherent acoustic interferometry to detect the uniaxial strain normal to the SrTiO 3 /aqueous interface directly caused by Ti–OH*. The spectral analysis applies a fairly general methodology for detecting a combination of the spatial extent, magnitude, and generation time of the interfacial strain through the coherent oscillations’ phase. For lightly n-doped SrTiO 3 , we identify the strain generation time (1.31 ps), which occurs simultaneously with Ti–OH* formation, and a tensile strain of 0.06% (upper limit 0.6%). In addition to fully characterizing this intermediate across visible, mid-infrared, and now GHz-THz probes on SrTiO 3 , we show that strain fields occur with the creation of some M–OH*, which modifies design strategies for tuning catalytic activity and provides insight into photo-induced degradation so prevalent for OER. To that end, the work put forth here provides a unique methodology to characterize intermediate-induced interfacial strain across OER catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface effect on resonant properties of nanowires predicted by an elastic theory for nanomaterials

A recently developed continuum theory considering surface effect in nanomaterials is adopted to investigate the resonant properties of nanowires with different boundary conditions in the present paper. The main feature of the adopted theory is that the surface effect in nanomaterials is characterized by the surface energy density of the corresponding bulk materials and the surface relaxation parameter in nanoscale. Based on a fixed-fixed beam model and a cantilever one, the governing equation of resonant frequency for corresponding nanowires is obtained. Numerical calculation of the fundamental resonant frequency is carried out, the result of which is well consistent with the existing numerical ones. Comparing to the result predicted by the conventionally structural dynamics, the resonant frequency of a fixed-fixed nanowire is improved, while that of a cantilever nanowire is weakened due to the surface effect. Both a decreasing characteristic size (height or diameter) and an increasing aspect ratio could further enhance the varying trend of resonant properties for both kinds of nanowires. The present result should be helpful for the design of nano-devices and nanostructures related to nanowires.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Strain effects and intermixing at the Si surface: Importance of long-range elastic corrections in first-principles calculations

Here we investigate Ge mixing at the Si(001) surface and characterize the 2 N Si(001) reconstruction by means of hybrid quantum and molecular mechanics calculations (QM/MM). Avoiding fake elastic dampening, this scheme allows to correctly take into account long range deformation induced by reconstructed and defective surfaces. We focus in particular on the dimer vacancy line (DVL) and its interaction with Ge adatoms. We first show that calculated formation energies for these defects are highly dependent on the choice of chemical potential and that the latter must be chosen carefully. Characterizing the effect of the DVL on the deformation field, we also find that the DVL favors Ge segregation in the fourth layer close to the DVL. Using the activation-relaxation technique (ART nouveau) and QM/MM, we show that a complex diffusion path permits the substitution of the Ge atom in the fourth layer, with barriers compatible with mixing observed at intermediate temperature. We also show that the use of QM/MM results in much more signi cant corrections at the saddle points (up to 0.5 eV) that at minima, demonstrating its importance for describing kinetics correctly.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sorption selectivity of birnessite particle edges: a d-PDF analysis of Cd( ii ) and Pb( ii ) sorption by δ-MnO 2 and ferrihydrite

Birnessite minerals (layer-type MnO2), which bear both internal (cation vacancies) and external (particle edges) metal sorption sites, are important sinks of contaminants in soils and sediments. Although the particle edges of birnessite minerals often dominate the total reactive surface area, especially in the case of nanoscale crystallites, the metal sorption reactivity of birnessite particle edges remains elusive. In this study, we investigated the sorption selectivity of birnessite particle edges by combining Cd(II) and Pb(II) adsorption isotherms at pH 5.5 with surface structural characterization by differential pair distribution function (d-PDF) analysis. We compared the sorption reactivity of δ-MnO2 to that of the nanomineral, 2-line ferrihydrite, which exhibits only external surface sites. Our results show that, whereas Cd(II) and Pb(II) both bind to birnessite layer vacancies, only Pb(II) binds extensively to birnessite particle edges. For ferrihydrite, significant Pb(II) adsorption to external sites was observed (roughly 20 mol%), whereas Cd(II) sorption was negligible. These results are supported by bond valence calculations that show comparable degrees of saturation of oxygen atoms on birnessite and ferrihydrite particle edges. Therefore, we propose that the sorption selectivity of birnessite edges follows the same order of that reported previously for ferrihydrite: Ca(II) < Cd(II) < Ni(II) < Zn(II) < Cu(II) < Pb(II).

54 ENVIRONMENTAL SCIENCES↗

A digital holography ex situ measurement characterization of plasma-exposed surface erosion from an electrothermal arc source

Digital holography has been proposed to fulfill a need for an imaging diagnostic capable of in situ monitoring of surface erosion caused by plasma–material interaction in nuclear fusion devices. A digital holography diagnostic for 3D surface erosion measurement has been developed at Oak Ridge National Laboratory with the goal of deployment on a plasma device. A proof-of-concept in situ demonstration is planned which would involve measurement of plasma erosion on targets exposed to an electrothermal arc source. This work presents the results of an ex situ characterization of the capability and limitations of holographic imaging of targets exposed to the arc source. Targets were designed to provide a fiducial for comparison of deformed and unaffected areas. The results indicated that the average net erosion was ~150 nm/plasma exposure, which is expected to be within the diagnostic’s measurement capacity. Surface roughness averages determined by holographic image analysis showed good agreement with measurements taken with a profilometer. Finally, the limit of the holography diagnostic’s x–y spatial resolution was characterized by comparison with scanning electron microscope imaging.

47 OTHER INSTRUMENTATION↗

Characterization of the Decaheme c-Type Cytochrome OmcA in Solution and on Hematite Surfaces by Small Angle X-Ray Scattering and Neutron Reflectometry

The outer membrane protein OmcA is an 85 kDa decaheme c-type cytochrome located on the surface of the dissimilatory metal-reducing bacterium Shewanella oneidensis MR-1. It is assumed to mediate shuttling of electrons to extracellular acceptors that include solid metal oxides such as hematite (α-Fe 2 O 3 ). No information is yet available concerning OmcA structure in physiologically relevant conditions such as aqueous environments. We purified OmcA and characterized its solution structure by small angle x-ray scattering (SAXS), and its interaction at the hematite-water interface by neutron reflectometry. SAXS showed that OmcA is a monomer that adopts a flat ellipsoidal shape with an overall dimension of 34 × 90 × 65 Å 3 . To our knowledge, we obtained the first direct evidence that OmcA undergoes a redox state-dependent conformational change in solution whereby reduction decreases the overall length of OmcA by ~7 Å (the maximum dimension was 96 Å for oxidized OmcA, and 89 Å for NADH and dithionite-reduced OmcA). OmcA was also found to physically interact with electron shuttle molecules such as flavin mononucleotide, resulting in the formation of high-molecular-weight assemblies. Neutron reflectometry showed that OmcA forms a well-defined monomolecular layer on hematite surfaces, where it assumes an orientation that maximizes its contact area with the mineral surface. Finally, these novel insights into the molecular structure of OmcA in solution, and its interaction with insoluble hematite and small organic ligands, demonstrate the fundamental structural bases underlying OmcA's role in mediating redox processes.

Environmental Molecular Sciences Laboratory↗

Adsorbed states of chlorophenol on Cu(110) and controlled switching of single-molecule junctions

A molecular junction of substituted benzene (chlorophenol) is fabricated and controlled by using a scanning tunneling microscope (STM). Prior to the junction formation, the bonding geometry of the molecule on the surface is characterized by STM and electron energy loss spectroscopy (EELS). EELS shows that the OH group of chlorophenol is dissociated on Cu(110) and that the molecule is bonded nearly flat to the surface via an O atom, with the Cl group intact. We demonstrate controlled contact of an STM tip to the “available” Cl group and lift-up of the molecule while it is anchored to the surface via an O atom. The asymmetric bonding motifs of the molecule to the electrodes allow for reversible control of the junction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Silica Surface States and their Wetting Characteristics

The wetting characteristics of silica (SiO 2 ) surfaces can be described by molecular dynamics (MD) and ab initio simulations, including comparison of silica surfaces (talc (001), siloxanated quartz, tridymite (001) and quartz (001)), some of which have not been considered previously in the literature. Classic MD and ab initio simulation methods have been used to determine the contact angle, interfacial water structure, hydroxylation reaction and hydration energy, the results of which are compared with experimental results reported in the literature. Additionally, wetting of silica surfaces depends on surface polarity and extent of hydroxylation. The non-polar siloxane surfaces are characterized by a contact angle of about 80°, an MD ‘water exclusion zone’ of about 3 Å, a relaxed interfacial water orientation, inertness to hydroxylation and minimal hydration energy. The polar silica surfaces can be wetted by water and have a more ordered interfacial water structure. Silanol groups form at the polar silica surface during hydroxylation reactions, and the calculated hydration energy of -1·2 and -1·6 eV matches the experimental heat of immersion measurements reported in the literature, which correspond to hydrogen (H) bonding with interfacial water. In conclusion, fundamental understanding of silica surfaces is important for understanding flotation phenomena and fluid flow in silica nanopores.

36 MATERIALS SCIENCE↗

Genesis of Gold Clusters from Mononuclear Gold Complexes on TiO[subscript 2]: Reduction and Aggregation of Gold Characterized by Time-Resolved X-Ray Absorption Spectroscopy

Mononuclear gold complexes bonded to TiO{sub 2} were synthesized from Au(CH{sub 3}){sub 2}(C{sub 5}H{sub 7}O{sub 2}), and their decomposition and conversion into gold nanoclusters on the TiO{sub 2} surface were characterized by time-resolved X-ray absorption and infrared spectroscopies as the temperature of the sample in flowing helium was ramped up. Mass spectra of the evolved gases were also measured during this process. The results show (a) the onset of formation of CH{sub 4} as a decomposition product, (b) the reduction of Au{sup III} to Au{sup 0}, and (c) the formation of Au-Au bonds, all occurring in approximately the same temperature range (about 335-353 K), indicating that the reduction and aggregation of the supported gold are simultaneous processes facilitated by the removal of methyl ligands initially bonded to the gold. IR spectra recorded during the treatment indicate that water on the TiO{sub 2} surface may be involved in the process by reacting with methyl groups bonded to Au{sup III} to give CH{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomic Layer Deposition (ALD) of Metal and Metal Oxide Films: A Surface Science Study (Final Report)

This is the final report for this project. The long-term objective of our project is to develop a general molecular-level picture of the surface chemistry associated with ALD processes. Our central hypothesis is that the chemistry of ALD precursors can differ significantly from that seen in solution. Awareness of such differences should provide general guidelines on what to watch for when synthesizing new ALD precursors and designing and optimizing new ALD processes, especially in terms of minimizing the incorporation of impurities in the growing films and of carrying out depositions under mild pressure and temperature conditions. The main objective of our research project has been to advance the fundamental knowledge of the surface chemistry of ALD precursors needed for the design and optimization of film deposition processes. A modern surface-science approach has been implemented to both elucidate the mechanism of the reactions of the precursors on the surface and characterize the composition and morphology of the growing films. In general, emphasis is being placed on: • Identifying the primary reactions that may lead to the deposition of clean films; •Identifying the secondary reactions that may help the ALD process, by, for instance, helping with the reduction (or oxidation) of the metal atom; • Identifying the secondary reactions that may lead to the deposition of undesirable impurities in the growing films; • Determining the kinetic parameters of the relevant surface reactions in order to define the optimum conditions for film deposition and to minimize impurity deposition. • Characterizing the nature of the resulting films, with focus on their stoichiometry and on the final oxidation states of the constituent elements; and • Using the information obtained to propose better precursors for given ALD processes.

36 MATERIALS SCIENCE↗

Improving fatigue performance of additively manufactured Ti-6Al-4V using sulfur-based self-terminating etching processes

The adoption of Additively Manufactured (AM) Ti-6Al-4V (Ti64) is continually increasing in the industry due to its benefits over the conventional manufacturing techniques. However, AM Ti64 parts are prone to poor surface finish, which significantly affects their fatigue performance. Therefore, AM Ti64 parts need post-processing to enhance surface finish and fatigue performance. Prior work with a sulfur-based self-terminating etching process for AM Ti64 demonstrated support removal and surface roughness reduction. To further this work, this manuscript details the impact of this sulfur-based post-processing technique on the mechanical properties and the fatigue life of AM Ti64 by characterizing the surface roughness, microstructural evolution, and fracture surfaces. Finally, this post-processing technique decreased the surface roughness parameter - S v by 55 % from 84 ± 11 µm to 38 ± 19 µm and increased the average fatigue life by 340 % from about 7000 cycles to 30,000 cycles.

36 MATERIALS SCIENCE↗

Carbon nanowalls as material for electrochemical transducers

The electrochemical reactivity of a carbon nanowalls electrode was highlighted. The carbon nanowalls were synthesized at 520 deg. C in an acetylene/ammonia electron cyclotronic resonance plasma without any metal catalyst. The electrode surface was characterized by scanning and transmission electron microscopy. Its electrochemical reactivity was studied by both cyclic voltammetry and electrochemical impedance spectroscopy. After the carbon nanowalls deposition, the electronic transfer rate constant and the electroactive surface area were found to be increased by a factor of 7 and 3, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A nitride-based epitaxial surface layer formed by ammonia treatment of silicene-terminated ZrB{sub 2}

We present a method for the formation of an epitaxial surface layer involving B, N, and Si atoms on a ZrB{sub 2}(0001) thin film on Si(111). It has the potential to be an insulating growth template for 2D semiconductors. The chemical reaction of NH{sub 3} molecules with the silicene-terminated ZrB{sub 2} surface was characterized by synchrotron-based, high-resolution core-level photoelectron spectroscopy and low-energy electron diffraction. In particular, the dissociative chemisorption of NH{sub 3} at 400 °C leads to surface nitridation, and subsequent annealing up to 830 °C results in a solid phase reaction with the ZrB{sub 2} subsurface layers. In this way, a new nitride-based epitaxial surface layer is formed with hexagonal symmetry and a single in-plane crystal orientation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗