Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface charging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

A study of charged particles/radiation damage to VLSI device materials

Future spacecraft systems such as the manned space station will be subjected to low-dose long term radiation particles. Most electronic systems are affected by such particles. There is therefore a great need to understand device physics and failure mechanisms affected by radiation and to design circuits that would be less susceptible to radiation. Using 2 MeV electron radiation and bias temperature aging, it was found that MOS capacitors that were prepositively biased have lower flatband voltage shift and lesser increase in density of surface state charge than those that were not prepositively biased. In addition, it was shown that there is continued recovery of flatband voltage and density of state charge in irradiated capacitors during both room temperature anneal and 137 degree anneal. When nMOS transistors were subjected to 1 MeV proton radiation, charge pumping and current versus voltage measurements indicated that transconductance degradation, threshold voltage shifts and changes in interface states density may be the primary cause of nMOS transistor failure after radiation. Simulation studies using SPICE were performed on CMOS SRAM cells of various transistor sizes. It is shown that transistor sizing affects the noise margins of CMOS SRAM cells, and that as the beta ratio of the transistors of the CMOS SRAM cell decreases, the effective noise margin of the SRAM cell increases. Some suggestions were made in connection with the design of CMOS SRAMS that are hardened against single event upsets.

Okyere, John G.↗

Improving Tracer Particle Surface Properties for Wind Tunnel Research

The surface properties of micron size polystyrene latex microspheres (PSLs) modified with quaternary alkylammonium (QA) surfactants were investigated, with a focus on the relationship between surface chemistry and adhesion. These investigations were motivated by the need to develop non-fouling tracer particles for wind tunnel studies. The goals were to relate the work of adhesion between particles and substrates to the type and amount of QA modifier in order to optimize the performance of PSL tracers. Surfactant-free emulsion polymerization (SFEP) can produce PSLs for wind tunnel tracers. Covalentlybound charged groups (derived from the initiator) stabilize PSL surfaces in water. This work used PSLs with anionic surface groups. Previous studies indicated that surface-bound charged groups on PSLs have a significant impact on their interfacial energy. Modifying charged surface groups therefore offers a method to modulate PSL interfacial properties. In this work, PSLs and films were modified by adsorption of QA surfactants.

Schmitz, Russell C.↗

Engineering spin coherence in core-shell diamond nanocrystals

Fluorescent diamond nanocrystals can host spin qubit sensors capable of probing the physical properties of biological systems with nanoscale spatial resolution. Sub-100 nm diamond nanosensors can readily be delivered into intact cells and even living organisms. However, applications beyond current proof-of-principle experiments require a substantial increase in sensitivity, which is limited by surface induced charge instability and electron-spin dephasing. In this work, we utilize engineered core-shell structures to achieve a drastic increase in qubit coherence times (T 2 ) from 1.1 to 35 μs in bare nanodiamonds to upward of 52 to 87 μs. We use electron-paramagnetic-resonance results to present a band bending model and connect silica encapsulation to the removal of deleterious mid-gap surface states that are negatively affecting the qubit’s spin properties. Combined with a 1.9-fold increase in particle luminescence these advances correspond to up to two-order-of-magnitude reduction in integration time. Probing qubit dynamics at a single particle level further reveals that the noise characteristics fundamentally change from a bath with spins that rearrange their spatial configuration during the course of an experiment to a more dilute static bath. The observed results shed light on the underlying mechanisms governing fluorescence and spin properties in diamond nanocrystals and offer an effective noise mitigation strategy based on engineered core-shell structures.

core-shell↗

Surface Enhanced Raman Scattering Selectivity in Proteins Arises from Electron Capture and Resonant Enhancement of Radical Species

Plasmon-enhanced Raman scattering is a powerful approach to detecting and characterizing proteins in live and dynamic biological systems. However, the selective detection/enhancement of specific residues as well as spectral diffusion and fluctuations have complicated the interpretation of enhanced Raman spectra and images of biological matter. In this paper, we therefore demonstrate that the amino acid tryptophan (Trp) can capture an electron from an excited plasmon, which generates a radical anion that is resonantly enhanced: a visible excited electronic state slides into resonance upon charging. This surface enhanced resonance Raman scattering (SERRS) mechanism explains the persistence of Trp signatures in the SERS and TERS spectra of proteins. Evidence for this picture includes the observation of visible resonances in the UV-Vis extinction spectrum, changes in the ground state vibrational spectrum, and plasmon-resonance dependent behavior. DFT calculations support the experimental observations. The behavior observed from the free Trp molecule is shown to explain the SERS spectrum of the Trp-cage protein. In effect, resonant Raman scattering from radicals formed through plasmonic excitation represents an under-investigated mechanism that may be exploited for chemical sensing applications. This work was supported by the National Institutes of Health Award R01-GM109988. The authors thank Hannah Shafaat for helpful discussions and providing an azurin sample for comparison. The authors also thank Joel Harris for providing constructive comments on our manuscript.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hierarchical Ion Interactions in the Direct Air Capture of CO 2 at Air/Aqueous Interfaces

The direct air capture (DAC) of CO 2 using aqueous solvents is plagued by slow kinetics and interfacial barriers that limit effectiveness in combating climate change. Functionalizing air/aqueous surfaces with charged amphiphiles shows promise in accelerating DAC; however, insight into these interfaces and how they evolve in time remains poorly understood. Specifically, competitive ion interactions between DAC reagents and reaction products feedback onto the interfacial structure, thereby modulating interfacial chemical composition and overall function. In this work, we probe the role of glycine amino acid anions (Gly - ), an effective CO 2 capture reagent, that promotes the organization of cationic oligomers at air/aqueous interfaces. These surfaces are probed with vibrational sum frequency generation spectroscopy and molecular dynamics simulations. Our findings demonstrate that the competition for surface sites between Gly - and captured carbonaceous anions (HCO 3 - , CO 3 2 -, carbamates) drives changes in surface hydration, which in turn tunes oligomer ordering. This phenomenon is related to a hierarchical ordering of anions at the surface that are electrostatically attracted to the surface and their ability to compete for interfacial water. These results point to new ways to tune interfaces for DAC via stratification of ions based on relative surface propensities and specific ion effects.

54 ENVIRONMENTAL SCIENCES↗

Radiating dipole model of interference induced in spacecraft circuitry by surface discharges

Spacecraft in geosynchronous orbit can be charged electrically to high voltages by interaction with the space plasma. Differential charging of spacecraft surfaces leads to arc and blowoff discharging. The discharges are thought to upset interior, computer-level circuitry. In addition to capacitive or electrostatic effects, significant inductive and less significant radiative effects of these discharges exist and can be modeled in a dipole approximation. Flight measurements suggest source frequencies of 5 to 50 MHz. Laboratory tests indicate source current strengths of several amperes. Electrical and magnetic fields at distances of many centimeters from such sources can be as large as tens of volts per meter and meter squared, respectively. Estimates of field attenuation by spacecraft walls and structures suggest that interior fields may be appreciable if electromagnetic shielding is much thinner than about 0.025 mm (1 mil). Pickup of such fields by wires and cables interconnecting circuit components could be a source of interference signals of several volts amplitude.

Metz, R. N.↗

Controlling and monitoring the space-station plasma interaction: A baseline for performing plasma experiments and using advanced technology

The size, complexity, and motion of space station through the Earth's environmental plasma means that there will be a large, complicated interaction region, involving a sheath, wake, charging of surfaces, induced electric fields, secondary emission, outgassing with ionization, etc. This interaction will necessarily be a factor in carrying out and interpreting plasma experiments and in the use of certain technologies. Attention should be given ahead of time to: (1) monitoring this interaction so that it is well described; (2) implifying the interaction by appropriate design and construction of the spacecraft and by appropriate planning of technology use; and (3) controlling the interaction by both active and passive means. Plasma emitters for modifying and controlling the spacecraft charge should be placed in several locations. Portable electrostatic shields could be deployed around noisy sections of the spacecraft in order to carry out sensitive experiments. A particle umbrella could be raised to deflect the ram ions and neutrals in order to provide a controlled environment. These interactions are briefly discussed.

Whipple, Elden C.↗

Effects of the surface termination and the oxygen vacancy position on LaNiO 3 ultra-thin films: First-principles study

In this study, while ultra-thin layers of the LaNiO 3 film exhibit a remarkable metal-insulator transition as the film thickness becomes smaller than a few unit cell (u.c.), the formation of possible oxygen vacancies and their effects on the correlated electronic structure have been rarely studied using first principles. Here, we investigate the effects of the surface termination and the oxygen vacancy position on the electronic properties and vacancy energetics of LaNiO 3 ultra-thin films under the compressive strain using density functional theory plus U (DFT + U). We find that oxygen vacancies can be easily formed in the Ni layers with the NiO 2 terminated surface (0.5 u.c. and 1.5 u.c. thickness) compared to the structures with the LaO terminated surface and the in-plane vacancy is energetically favored than the out-of-plane vacancy. When two vacancy sites are allowed, the Ni square plane geometry is energetically more stable in most cases as two oxygen vacancies tend to stay near a Ni ion. Strong anisotropy between the in-plane and out-of-plane vacancy formation as well as the layer and orbital dependent electronic structure occur due to strain, surface termination, charge reconstruction, and quantum confinement effects. The in-plane vacancy of the NiO 2 terminated structure is favored since the released charge due to the oxygen vacancy can be easily accommodated in the d x 2 -y 2 orbital, which is less occupied than the d z 2 orbital. Remarkably, the oxygen vacancy structure containing the Ni square-plane geometry becomes an insulating state in DFT + U with a sizable band gap of 1.2 eV because the large crystal field splitting between d z 2 and d x 2 -y 2 orbitals in the square-plane favors an insulating state and the Mott insulating state is induced in other Ni sites due to strong electronic correlations. In the thin-film structure without oxygen vacancies, the strong correlation effect in DFT + U drives a pseudogap ground state at the Fermi energy, similarly as the experimental photo-emission spectra; however, the variation of the DFT + U electronic structure depending on the surface termination becomes weaker compared to those obtained in DFT.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Saltation threshold detection in a wind tunnel by the measurement of the net electrostatic charge

The Mars surface wind tunnel (MARSWIT) is an open circuit wind tunnel used for aeolian studies and is located inside a large vacuum chamber allowing testing at Martian surface atmospheric pressure. Since direct access is not available to the tunnel during operation at low pressure, a remote method of saltation detection is needed. The bed is observed by means of closed circuit video, but it is often difficult to determine the initiation of threshold. The measurement by means of an electrometer of the net electric charge produced by the saltating particles has provided a reliable means of saltation threshold detection. Saltating particles become charged several ways, both in wind tunnels and in a natural environment. The most significant of these methods are tribo-charging and contact charging, which always occur. Fracture charging may also occur under the high velocities associated with particle transport on Mars or under simulated Martian conditions. Detection in MARSWIT is achieved by allowing the saltating particles to impinge on a planar conducting surface normal to the flow that is connected to ground through a Keithly electrometer. The signal from the electrometer is connected to a strip chart recorder along with the analog signal from the pitot tube transducer that is used to determine the wind velocity in the tunnel. Thus, a record of wind velocity and the initiation of particle saltation is conveniently displayed together. While both positive and negative charges are produced during saltation, this method measures only the net charge; thus the charge may be either positive or negative depending upon the particles being tested, the size and size distribution of the test material, and the wind velocity. This has proven to be a very trustworthy and sensitive method of saltation threshold detection, being especially useful with the smaller sized particles which are the most difficult to observe visually.

Leach, Rodman N.↗

Fracto-emission - The role of charge separation

Fracto-emission is the emission of particles (e.g., electrons, ions, ground state and excited neutrals, and photons) during and following fracture. It is found that during fracture in vacuum of adhesive bonds and crystalline materials involving large amounts of charge separation on the surface the emission of charged particles, excited neutrals, light, and radio waves occurs with unique and revealing time dependencies. Simultaneous fracto-emission measurements on several systems are reported. The results are interpreted in terms of a conceptual model involving the following steps: (1) charge separation due to fracture, (2) desorption of gases from the material into the crack tip, (3) a gas discharge in the crack, (4) energetic bombardment of the freshly created crack walls, and (5) thermally stimulated electron emission, accompanied by electron stimulated desorption of ions and excited neutrals. In addition to evidence from fracture experiments, results from studies of electron bombardment of a polymer surface are presented.

Dickinson, J. T.↗

Modeling of Carbon Nanotube Schottky Barrier Reduction for Holes in Air

A model is proposed for the recently observed lower Schottky barrier for holes in air than in vacuum at a metallic electrode - semiconducting carbon nanotube (CNT) junction. In air, the CNT is oxidized. The oxygen molecules on the CNT surface will attract negative charges and will be negatively charged. The negative charges on the solid surface generally enhance the surface dipole and provide stronger electron confinement within the solid. Thus the CNT work function will increase in air. Then the Schottky barrier for holes will have to increase in air according to the standard band-alignment theory, but this is against the experiment. In order to overcome this difficulty, we propose a new Schottky barrier model, assuming that there is a transition region between the electrode and the CNT, where an appreciable potential can drop. We assume that electrodes are placed at the side of the CNT and the contact is formed via the van der Waals interaction. Since the electrode surface is not atomically flat in practical situations, the contact will not be intimate and there will be a transition region before the usual metallic bulk structure starts. In this view, the Schottky barrier is determined not only by the work function difference of the electrodes and the CNT, but also by the potential drop in the transition region. The oxidation increases the potential drop and leads to a lower Schottky barrier for holes. This relation will be demonstrated in a graphical manner by expressing the potential drop as a function of CNT band bending. The potential drop is comparable to the CNT band gap when, e.g., the transition region is about a few Angstroms thick, the oxygen molecule coverage is about 10 %, and an oxygen molecule is charged by about 0.01-0.1 of the unit charge (1-10 % of molecules are charged). The proposed mechanism prevails for both p - and n-CNTs. The model consistently explains the CNT oxidation experiments reported so far.

Yamada, Toshishige↗

ISS Local Environment Spectrometers (ISLES)

In order to study the complex interactions between the space environment surrounding the ISS and the ISS surface materials, we propose to use lowcost, high-TRL plasma sensors on the ISS robotic arm to probe the ISS space environment. During many years of ISS operation, we have been able to condut effective (but not perfect) extravehicular activities (both human and robotic) within the perturbed local ISS space environment. Because of the complexity of the interaction between the ISS and the LEO space environment, there remain important questions, such as differential charging at solar panel junctions (the so-called "triple point" between conductor, dielectric, and space plasma), increased chemical contamination due to ISS surface charging and/or thruster activation, water dumps, etc, and "bootstrap" charging of insulating surfaces. Some compelling questions could synergistically draw upon a common sensor suite, which also leverages previous and current MSFC investments. Specific questions address ISS surface charging, plasma contactor plume expansion in a magnetized drifting plasma, and possible localized contamination effects across the ISS.

Krause, Linda Habash↗

Elucidating the speciation of extracted lanthanides by diglycolamides

Many studies over the past few decades have been devoted to addressing the application of diglycolamides (DGAs) for hydrometallurgical-based, f-element separations. Work to date has shown the molecular structure of a DGA derivative can have a significant impact on intra-lanthanide partitioning patterns. More recent studies have pushed towards probing the structure function relationship of the lanthanide-DGA complex to enable the design of more efficient lanthanide separation systems. Spectroscopic techniques, such as UV–Visible, Fourier Transformed Infrared Spectroscopy (FT-IR), Nuclear Magnetic Resonance (NMR), and Extended X-ray Absorption Fine Structure (EXAFS), provide information regarding the inner-sphere coordination of a given lanthanide-DGA complex. Scattering techniques, such as Dynamic Light Scattering (DLS), Small-Angle X-ray Scattering (SAXS), and Small-Angle Neutron Scattering (SANS), address nanoscale structures including aggregate sizes and morphology. Here, this review assesses the current state-of-knowledge regarding lanthanide-DGA hydrometallurgical (i.e., solvent extraction systems) interrogated using spectroscopic and scattering techniques to characterize the extracted Ln 3+ DGA species. Of particular interest to this review is the impact of varied diluents, inclusion and variation of phase modifiers, and DGA derivatization on system characteristics. While there has been extensive literature on the application of DGAs for f-element separations, the literature lacks a collective assessment of the speciation of Ln 3+ in the organic phase. This review provides new insights into the field of DGA separations, explicitly with an application to intra-lanthanide separations. Specifically, this review illustrates the importance of both the co-extraction anion (Cl - , NO 3 - , or ClO 4 - ) as it pertains to both the aggregate size and Ln 3+ distribution coefficient. It is evident the ability of the anion to disrupt the hydrogen bonding network limits both aggregate size and distribution coefficients according to the Hoffmeister series. This suggests the importance of the large, softer anions with a low charge-to-surface area ratio on encouraging hydrogen bond interactions. In addition, the co-extracted cation (H + vs Na + ) is important for mitigating transfer of Ln 3+ from the aqueous to the organic phase through extensive hydrogen bonding networks. These networks are responsible for forming supramolecular aggregates where a change in morphology is observed with increasing concentrations of H + and/or Ln 3+ in the organic phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Zeta potential measurements of SiO 2 and TiO 2 particles in anionic and cationic surfactant solutions

Zeta potential measurements can provide valuable insights into colloidal stability and may reflect changes in the electrochemical double layer that influence electrocatalysis. In this study, we used zeta potential measurements to monitor and investigate the adsorption behavior of anionic sodium dodecyl sulfate (SDS), cationic dodecyl trimethyl ammonium bromide (DTAB), and cationic cetyl trimethyl ammonium bromide (CTAB) surfactants on SiO 2 and TiO 2 particles in DI water. The zeta potentials of SiO 2 and TiO 2 particles were measured as a function of particle concentration in 1.0 mM, 5.0 mM, and 10.0 mM surfactant solutions. Results indicate that there is no significant adsorption of DS - ions on SiO 2 particles across all SDS concentrations investigated in this study. The zeta potential of TiO 2 particles shifts from negative to positive as particle concentration increases at 1.0 mM SDS, indicating a decrease in DS - ions adsorption per TiO 2 particle. Adsorption plateaus at 5.0 mM SDS for all TiO 2 concentrations studied. In contrast, DTA + and CTA + ions showed clear adsorption on SiO 2 particles, but DTA + exhibited no apparent adsorption on TiO 2 particles. Interestingly, CTA + adsorption on TiO 2 was only evident at higher surfactant concentrations. This study presents a systematic investigation of zeta potential behavior as a function of particle and surfactant concentration, highlighting adsorption saturation and electrostatic reversal. Unlike prior work that was limited to single particle concentration measurements, our approach reveals how surfactant adsorption per particle decreases with increasing surface area. Despite the structural similarity between DTAB and CTAB, this study captured the different adsorption behaviors of both surfactants on SiO 2 and TiO 2 , emphasizing the role of the overall structure of the surfactant on surfactant adsorption behavior. These insights refine the interpretation of zeta potential data and advance understanding of surfactant adsorption on oxide particles. The insight provided in this study about surfactant adsorption on SiO 2 and TiO 2 particles could have important implications for the design of more effective colloidal and catalytic systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗