Search NASA⌕ Search

SEARCH · Search NASA

Results for “temperature control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

MAGNETICALLY SUSPENDED CANNED ROTOR PUMPS FOR THE INTEGRAL MOLTEN SALT REACTOR

This project developed a molten salt pump design for small modular reactors, concentrated solar, and Gen IV nuclear reactors with a magnetically levitated rotor that can operate at temperatures of up to 700 °C. This eliminates the need for rotating seals and roller element bearings which require maintenance and are prone to failure. The pump design is also more compact than existing molten salt pump designs which require long shafts to thermally isolate the electric motor. The aims of the project are to: 1) design and test the molten salt pump, 2) develop and test a high temperature position sensor needed for magnetic bearing control, and 3) develop and test high temperature coil fabrication methods for electric motor and magnetic bearing fabrication. To develop the high temperature coils, conductor materials were analyzed for oxidation, diffusion, cladding, and resistivity. Of the candidate conductor materials that met the requirements, silver was chosen. The long-term impact of radiation on silver resistivity was analyzed by developing a model of a generic molten salt fast reactor to model the conductor irradiation in worst case scenarios. The analysis showed that increased resistivity due to transmutation of silver decreases exponentially with the reactor reflector thickness. Different electrical insulation materials were tested and the final high temperature coils developed were able to withstand conductor to ground voltages up to 1800 V before insulation breakdown. Magnetic bearings require high-precision high-speed measurements of the rotor position to operate. Current commercial position sensors can only operate up to 550 °C so a novel position sensor was developed that can operate up to 800 °C. These sensors were also designed to measure the position of the metallic rotor through a thin metallic corrosion barrier that protects that coils, insulation, and magnetic cores so that the salt containment barrier does not have any penetrations. The high-temperature sensor was tested and had comparable performance to commercially available inductive position sensors. The sensor design and signal processing has led to several invention disclosures. The magnetically levitated molten salt pump design was completed and analyzed. The chloride salt test loop at Oak Ridge National Laboratory was chosen to test the pump and the pump hydraulics and power were designed for the test loop flow and pressure requirements. Classes of motor designs that do not utilize permanent magnetic were considered for the high-temperature motor. After extensive analysis of their performance, a synchronous reluctance motor was chosen for the pump. The design was refined and analyzed to optimize performance. The magnetic bearings were designed to meet the force and frequency requirements necessary to levitate the rotor and reject disturbances from rotor imbalance, motor forces, and hydraulic forces. Compliant mounts for the position sensors were designed that would not damage the ceramic sensor components and maintain sensor alignment over a wide temperature range. A thermal hydraulic analysis of the molten salt coolant flow used to cool the rotor and stator was performed to ensure that the maximum temperature in the rotor and stator will not exceed 725 °C. The corrosion barrier and casing were designed to maintain the salt fluid boundary by using compliant features to absorb large expansion mismatches due to different coefficients of thermal expansion (CTE). Finally, the salt drain and fill systems were designed along with the pump support structure, integration with the test loop, and thermal insulation and heating. Corrosion barrier fabrication experiments were performed to assess using laser cladding to apply a sub-millimeter corrosion barrier to the surface of a Fe-Co-V magnetic core material. The cladding method showed minimal mixing between materials at their interface and withstood temperature cycling without damage to the cladding. The technology commercialization is focused on the high-temperature position sensors and there has been significant interest from the nuclear industry in utilizing these sensors along with some interest from the aerospace industry. The project also led to a research collaboration with a fusion energy industrial partner to study barriers to scaling the pump design from the kW size to the MW size. This research collaboration will also study methods to create high-temperature coils that have conductor to ground breakdown voltages above 5 kV. The successful development of high-temperature electromagnetic coils and high-temperature position sensors greatly increases the temperature limits for electromagnetic devices that don’t rely on permanent magnets. This includes electric motors, magnetic bearings, linear actuators, rotary position and velocity sensing, actuated valves, and generators to name a few. This will fill a current need in molten salt reactors, concentrated solar, and fusion energy for these critical peripheral devices needed for practical reactor designs that do not currently have commercial solutions.

Hines, J Wesley↗
DOE OSTI2022

Rapid Load Transition for Integrated Solid Oxide Fuel Cell - Gas Turbine (SOFC-GT) Energy Systems: A Demonstration of the Potential for Grid Response

Rapid load transition is an essential requirement for integrated energy systems to maintain grid resilience as more renewable resources are added to the grid. Integrated solid oxide fuel cell - gas turbine (SOFC-GT) systems can provide high efficiency and low carbon emissions over a broad range of turndown. These hybrids also have the potential to enable rapid grid response. The challenge has been to demonstrate effective control strategies to manage load transitions. In the present study, a load transition of ~50% was achieved in 10 s using a novel but simple strategy. Power demand on the SOFC and the GT were ramped down concurrently. During this transition, the SOFC anode fuel was manipulated to maintain SOFC fuel utilization while the cathode inlet air flow and temperature were also manipulated to thermally protect the SOFC. This study was conducted using the Hybrid Performance (Hyper) facility at the National Energy Technology Laboratory (NETL) in a co-simulation environment with the Idaho National Laboratory (INL)'s grid-simulation. The load ramping strategy was tested using a hardware-based cyber-physical simulation methodology. The results demonstrate a high-fidelity representation of SOFC-GT hybrid dynamics and validation of the control strategy. Thermal and electrochemical transients indicated that the SOFC was well protected during rapid load turndown without violating operability constraints. This demonstration revealed the non-linear nature of tightly coupled SOFC-GT system components, especially the non-linear response of SOFC cathode air flow and inlet temperature controls. These results highlight the needs and challenges in developing adaptive automatic controls for autonomous rapid load transitions. This work demonstrates that SOFC-GT hybrids are a viable option to provide the fast-ramping characteristics essential to accommodate high levels of variable renewable power while maintaining grid resilience, reliability, and environmental performance. The results also demonstrate the utility of co-simulation in advancing the tightly-coupled integrated energy systems needed to meet goals for zero-carbon power generation.

DIRECT ENERGY CONVERSION,POWER TRANSMISSION AND DI↗
DOE OSTI2024

Precision Loading and Delivery of Molecular Cargo by Size-Controlled Coacervation of Gold Nanoparticles Functionalized with Elastin-like Peptides

Thermoresponsive elastin-like peptides (ELPs) have been extensively investigated in biotechnology and medicine, but little attention has been paid to the process by which coacervation causes ELP-decorated particles to aggregate. Here, using gold nanoparticles (AuNPs) functionalized with a cysteine-terminated 96-repeat of the VPGVG sequence (V96-Cys), we show that the size of the clusters that reversibly form above the ELP transition temperature can be finely controlled in the 250 to 930 nm range by specifying the concentration of free V96-Cys in solution and using AuNPs of different sizes. We further find that the localized surface plasmon resonance peak of the embedded AuNPs progressively red-shifts with cluster size, likely due to an increase in particle–particle contacts. We exploit this fine control over size to homogeneously load precise amounts of the dye Nile Red and the antibiotic Tetracycline into clusters of different hydrodynamic diameters and deliver cargos near-quantitatively by deconstructing the aggregates below the ELP transition temperature. Beyond establishing a key role for free ELPs in the agglomeration of ELP-functionalized particles, our results provide a path for the thermally controlled delivery of precise quantities of molecular cargo. This capability might prove useful in combination photothermal therapies and theranostic applications, and to trigger spatially and temporally uniform responses from biological, electronic, or optical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Investigation of modified uni-traveling carrier photodiode for cryogenic microwave photonic links

Quantum devices present the potential for unparalleled computing and communications capabilities; however, the cryogenic temperatures required to successfully control and read out many qubit platforms can prove to be very challenging to scale. Recently, there has emerged an interest in using microwave photonics to deliver control signals down to ultracold stages via optical fiber, thereby reducing thermal load and facilitating dense wavelength multiplexing. Photodetectors can then convert this optical energy to electrical signals for qubit control. The fidelity of the quantum operations of interest therefore depend heavily upon the characteristics of the photodiode, yet experimental demonstrations of fiber-coupled photodetection systems at low temperatures are relatively few in number, leaving important open questions regarding how specific detectors may perform in real-world cryogenic settings. In this work, we examine a highly linear modified uni-traveling carrier photodiode (MUTC-PD) under C-band illumination (1530–1565 nm) at three temperature regimes (300 K, 80 K, and ∼4 K) and multiple bias conditions. Our findings of reduced responsivity but preserved bandwidth are consistent with previous studies, while our saturation tests suggest a variety of potential applications for MUTC-PDs in cryogenic microwave photonics with and without electrical bias. Overall, our results should provide a valuable foundation for the continued and expanding use of this detector technology in quantum information processing.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

An experimental study of synthetic Hydroxybastnäsite-(La) solubility and speciation in carbonate bearing aqueous solutions at 175–250 °C

The transport and enrichment of rare earth element (REE) ore bodies are dependent on the stability of aqueous metal ligand complexes and the solubility of REE bearing minerals. REE ores are commonly associated with igneous systems having aqueous fluids with high carbonate concentrations and REE solubilities have been shown to be dependent on temperature and associate anion aqueous ligands present in solution. Furthermore, this work presents solubility experiments of hydroxybastnäsite-(La) at elevated temperatures in aqueous solutions of varying carbonate concentrations. At lower temperatures, hydroxybastnäsite-(La) solubility is controlled by neutral mono-carbonate LaCO 3 OH° but at higher temperatures and activities of carbonate species, charged di-carbonate La(CO 3 ) 2 - increases and predominates. This divergence, and the difference in solubility products of other hydroxybastnäsite-(REE) phases, provides a potential mechanism for REE fractionation in carbonate dominated aqueous solutions. To illustrate one such mechanism the solubility data of hydroxybastnäsite-(La) is compared with previously reported data of hydroxybastnäsite-(Nd) at elevated temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Climate-Driven Limits to Future Carbon Storage in California's Wildland Ecosystems

Enhanced ecosystem carbon storage is a key component of many climate mitigation pathways. The State of California has set an ambitious goal of carbon neutrality by 2045, relying in part on enhanced carbon sequestration in natural and working lands. We used statistical modeling, including random forest and climate analog approaches, to explore the climate-driven challenges and uncertainties associated with the goal of long-term carbon sequestration in forests and shrublands. We found that seasonal patterns of temperature and precipitation are strong controllers of the spatial distribution of aboveground live carbon. RCP8.5 projections of temperature and precipitation are estimated to drive decreases of 16.1% ± 7.5% in aboveground live carbon by the end of the century, with coastal areas of central and northern California and low/mid-elevation mountain areas being most vulnerable. With RCP4.5 projections, declines are less severe, with 8.8% ± 5.3% carbon loss. In either scenario, increases in temperature systematically cause biomass declines, and the spread of projected precipitation across 32 CMIP5 models contributes to substantial uncertainty in the magnitude of that decline. Projected changes in the environmental niche for the 20 most biomass-dominant tree species revealed widespread replacement of conifers by oak species in low elevation regions of central and northern California, with a corresponding decline in carbon storage depending on expected migration rates. The spatial patterns of vulnerability we identify may allow policymakers to assess where carbon sequestration in aboveground biomass is an appropriate part of a climate mitigation portfolio, and where future climate-driven carbon losses may be a liability.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Advances in the long-pulse steady-state high beta H-mode scenario with active controls of divertor heat and particle fluxes in EAST

Since the last IAEA-Fusion Energy Conference, the Experimental Advanced Superconducting Tokamak (EAST) research program has been, in support of ITER and CFETR, focused on development in terms of the long-pulse steady-state (fully noninductive) high beta H-mode scenario with active controls of the stationary and transient divertor heat and particle fluxes. The operational domain of the steady-state H-mode plasma scenario has been significantly extended with ITER-like tungsten mono-block divertor, plasma control and heating schemes. EAST has achieved several important milestones in the development of high β p H-mode scenario and its key physics and technologies. A 60 s-scale long-pulse steady-state high β p H-mode discharge with the major normalized plasma parameters similar to the designed performance of the CFETR 1GW fusion power operation scenario has been successfully established and sustained by pure RF heating and current drive. Several feedback control schemes have been developed for a sustained detachment with good core confinement. This includes control of the total radiation power, target electron temperature, and particle flux measured using divertor Langmuir probes or a combination of the control of target electron temperature and AXUV radiation near the X point. The detachment feedback control schemes have been integrated with small-ELM regimes and high β p scenario via neon seeding, enabling a core and edge compatible integrated high-beta scenario applicable to long-pulse operations. ELM suppression has been achieved using various methods, including resonant magnetic perturbations and impurity seeding. Full suppression of ELMs by using n=4 RMPs has been demonstrated for ITER for the first time in low input torque plasmas in EAST. Finally, EAST has been operated with helium to support the ITER research requirements for the first time. For a long-pulse, high bootstrap current fraction operation, a new lower tungsten divertor with active water-cooling has been installed, along with improvements in the heating and current drive capability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Nano-imaging of strain-tuned stripe textures in a Mott crystal

The 4d transition metal perovskites Ca n+1 Ru n O 3n+1 have attracted interest for their strongly interacting electronic phases showing pronounced sensitivity to controllable stimuli like strain, temperature, and even electrical current. Through multi-messenger low-temperature nano-imaging, we reveal a spontaneous striped texture of coexisting insulating and metallic domains in single crystals of the bilayer ruthenate Ca 3 (Ti x Ru 1-x ) 2 O 7 across its first-order Mott transition at T ≈ 95K. We image on-demand anisotropic nucleation and growth of these domains under in situ applied uniaxial strain rationalized through control of a spontaneous Jahn-Teller distortion. Our scanning nano-susceptibility imaging resolves the detailed susceptibility of coexisting phases to strain and temperature at the transition threshold. Comparing these nano-imaging results to bulk-sensitive elastoresistance measurements, we uncover an emergent “domain susceptibility” sensitive to both the volumetric phase fractions and elasticity of the self-organized domain lattice. Our combined susceptibility probes afford nano-scale insights into strain-mediated control over the insulator-metal transition in 4d transition metal oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Slag Management of Carbon Feedstock Used in Gasification FY17 TCF between Eastman Chemical and NETL (Final Report)

NETL, in collaboration with Eastman Chemical Corp (Kingsport, TN), targeted the joint evaluation and refinement of a slag management program developed by NETL (NETL IP, patent applied for) to control gasifier slag properties formed from ash in individual or combinations of different coal-based carbon feedstock materials and specific slag modifiers used in gasification. Slag forms from mineral or organic-metallic impurities in the carbon feedstock that melt at the high temperatures of gasification, coalescing to form a liquid (slag) that must flow from the gasifier. Slag additives, also known as slag modifiers, are often added to the carbon feedstock to modify the ash chemistry and achieve desired slag flow properties at target temperatures used in gasification. If slag does not flow from a gasifier, its buildup within the gasification chamber will cause either gasifier shutdown to physically remove the slag (consuming time and damaging the protective refractory lining), or the gasification temperature must be increased to lower slag viscosity so it can flow from the gasifier, leading to greater refractory wear/corrosion, along with increased fouling and downstream component wear. Because of these issues, gasification is typically targeted at the lowest temperature possible where slag will flow in a controlled manner (a temperature range called T100 for the lowest temperature, with T250 being the highest temperature where the slag has achieved the desired fluidity). That temperature range also needs to yield a desired syngas composition, highlighting the importance of knowing and being able to control carbon feedstock slag viscosity and the temperature of thermal breakdown of the carbon feedstock. Slag viscosity varies with changes in the gasification chamber temperature, oxygen partial pressure, and slag chemistry. The slag model work with Eastman Chemical targeted predicting and controlling molten coal ash slag behavior at specific gasification conditions. The final goal of the refined model was to develop/refine the NETL slag model so a gasifier operator would be able to predict slag behavior prior to purchasing or using a carbon feedstock and control slag properties once a carbon feedstock is being gasified, allowing a gasifier user to determine what mineral additives or blends of different carbon materials would be needed to achieve desired slag properties at targeted gasification conditions. For a given carbon feedstock and desired gasification condition, the actual gasification cost and slag behavior would be able to be predicted using the slag management program in advance of purchasing or using the carbon feedstock – allowing accurate control of slag ash behavior in real time. As part of the TCF project work with Eastman Chemical, the viscosity of several ash compositions of interest to them would be measured and used to populate the slag model, along with a large database of historical slag temperature, chemistry, and viscosity information they possess – information that would in-crease the predictive accuracy of the slag management model with slag ash chemistry of interest to them. As part of the model evaluation and refinement, the predictive model and its database will be installed on computers at Eastman Chemical and used to manage slag properties in a gasifier during real-time operation of their gasifier. In summary, success of the slag management program at Eastman Chemical would support its use by other gasifier operators to manage slag chemistry and properties over other desired gasification temperature ranges, allowing greater process control and efficiency of their carbon feedstock conversion during gasification.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Influence of mass ablation on ignition and burn propagation in layered fusion capsules

After decades of research, recent laser-driven inertial fusion experiments have demonstrated rapid progress toward achieving thermonuclear ignition using capsule designs with cryogenic fuel layers. The ignition physics for these layered capsules involves a complex interplay between the dynamically forming hot spot and the dense surrounding fuel. Using analytic theory and numerical simulations, we demonstrate that the mass ablation rate into the hot spot depends sensitively upon the temperature of the dense fuel, resulting in ablative inflows up to [Formula: see text] faster than previous estimates. This produces an enthalpy flux into the hot spot that plays a critical role in controlling the hot spot temperature, the ignition threshold, and the subsequent burn propagation. The net influence of mass ablation on the ignition threshold is regulated by a dimensionless parameter that depends upon the temperature of the dense fuel. As a consequence, the ignition threshold is sensitive to any mechanism that heats the dense fuel, such as neutrons or radiation emitted from the hot spot. These predictions are confirmed using radiation-hydrodynamic simulations for a series of capsules near ignition conditions. This analysis may have relevance for understanding the variable performance of recent experiments and for guiding new capsule designs toward higher fusion yields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Adaptive Control for Load-Following of Boiling Water Reactors Part I: Linear Systems and Fully-Observable Dynamics

Automation control is a key strategy to improve the economic competitiveness of nuclear power plants. Not only does it help reduce operational costs, but it also extends the value proposition of these plants to nontraditional markets, including unattended operations in remote villages and space. However, the dynamics of the operating environments of nuclear reactors are subject to changes over time, and there are no widely adopted methods to ensure that the automation strategy will remain effective over the extended durations required for these applications. Adaptive control is a discipline that offers the possibility to accommodate such changes online. However, it relies on mathematical assumptions that must be respected to ensure robustness and reliability. In this work, we derive an adaptive control formulation for linear systems in which all states are observable and apply it to an instance of load-follow operation for Boiling Water Reactors. We assumed uncertainty in two factors: the temperature coefficient and the control rod worth, both of which are affected over time by the evolution of the nuclear reactor core environment. With an arbitrary penalty factor of 5, we found that the mean absolute and integral time absolute errors can be reduced by more than 90%, underscoring the strength of adaptive control. To extend the application to more challenges, different uncertainties and load-follow trajectories, as well as new formulations that include non-linearity and partial observability, are currently being developed.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Effects of Wire Diameter and Filament Size on the Processing Window of Bi-2212 Round Wire

High engineering critical current density (J E of 1300 A/mm 2 at 4.2 K and 15 T) in Bi-2212 round wire has been achieved through a partial melt, overpressure heat treatment process. J E varies strongly with processing conditions, particularly the maximum heat treatment temperature (T max ). Increasing T max results in longer time in the melt (defined as the time between when Bi-2212 melts on heating and when Bi-2212 begins to form on cooling), more bridging between the filaments, lower J E , and higher ac losses. A wide processing window with a large range of T max that has a nearly constant J E is desired for processing large coils with large thermal mass and significant thermal time constants that may make precise control over the desired temperature – time profiles uncertain. Accordingly, we wanted to explore broadening the T max window by controlling the Bi-2212 powder melting or wire architecture design. In this work, we report on studies of the performance variation with T max for two production wires with a filling factor of about 20% and 85 × 18 filaments where filament size was varied by changing the wire diameter, a process which also shortens the distance between filaments. We found that wires with smaller filament diameter (9 to 11 μm) showed a peak J E at the low end of T max and also a J E that was more sensitive to T max . A J E – T max plot showed a plateau J E (4.2 K, 5 T) of ~1100 A/mm 2 between T max of 886 and 894 °C for 1.0 and 1.2 mm wires, where J E is less sensitive to the wire diameter and T max . This J E plateau range is a preferred processing window for achieving high J E in coils.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Design Considerations for Controlling Silicon Nanoparticle Nucleation and Growth in a Nonthermal Plasma

Controlling the nucleation and growth of nanoparticles in low temperature plasma systems is imperative for controlling nanoparticle size distributions; and for some applications such as deposition and etching in microelectronic processing, preventing particle contamination. In this work, silicon nanoparticle (NP) production from silane is used as a model system to investigate the nucleation process. Although the mechanisms responsible for silicon NP nucleation and growth have been studied, it is unclear how controllable system parameters (e.g., pressure, system geometry, and gas composition) can be used to inhibit or promote NP formation. For example, the transport of reactive silane species is expected to significantly affect the feed fraction of silane required to nucleate silicon NP (the nucleation onset fraction) due to losses at the reactor walls. In this work, NP mass density was determined as a function of system pressure, gas composition, and reactor diameter for a tubular flow-through radiofrequency (RF) plasma using Ar/H2/He/SiH4 gas mixtures. A quartz crystal microbalance (QCM) impactor was developed to measure the total aerosol mass density downstream of the plasma and thereby identify the nucleation onset and its dependence on process parameters. Finally, a reaction mechanism was developed and incorporated into a global plasma chemistry model to better understand the nucleation onset and NP growth.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Performance and flexibility improvements of Staged Pressurized Oxy-Combustion

Staged Pressurized Oxy-Combustion (SPOC) is a low-carbon coal combustion power technology being developed by Washington University in St. Louis (WUSTL). Oxy-combustion plants enable straightforward capture of carbon dioxide (CO 2 ) by removing most of the nitrogen in the combustion air prior to use, thereby burning fuel in near-pure oxygen instead of air, producing a flue gas containing primarily CO 2 and water. CO 2 capture at amounts > 90% is possible, often using cryogenic air separation. Oxy-combustion typically relies on flue gas recycle (FGR) to reduce the peak temperature and radiation that would otherwise occur in a fuel/oxygen only flame. SPOC reduces the peak temperatures of combustion by utilizing two or more pressurized boiler modules connected in series to produce fuel staging; hence, only a portion of the fuel is combusted in any given furnace module. This means that the thermal energy released at each stage can be captured and removed from the gases prior to subsequent stages, when more fuel is introduced. This allows the SPOC process to operate with minimal FGR, avoiding the associated efficiency losses and additional costs. Also, the process operates at an elevated gas-side pressure, reducing boiler size, enhancing heat transfer to achieve a compact boiler configuration as compared to an atmospheric-pressure boiler design, and allowing for recovery of the latent heat of the water from the flue gas at a temperature useful to the steam cycle. The resultant net efficiency of the system is over 3 percentage points greater than traditional atmospheric-pressure oxy-combustion, and 7 percentage points greater than the post combustion variant, representing a step-change improvement over first-generation capture technologies. To further develop the concept, WUSTL and the Electric Power Research Institute, Inc., organized a project with American Air Liquide, Inc., Doosan Babcock Limited, and the U.S. Department of Energy to investigate a practicable and workable boiler design. The team has identified the potential for enhanced process flexibility for controlling power generation over a wider load range than is normally available to conventional coal-fired power plants due to the staged nature of the heat release. With increasing intermittent renewable generator contribution, on-demand generators need to be highly flexible to participate in the future energy market, requiring extensive operation at reduced load. Conventional coal-fired steam generators typically face challenges in maintaining temperature control of the reheat steam and main steam at reduced loads. This results in inefficient operation, both in terms of the boiler efficiency and steam turbine heat rate. The results of this project show the SPOC process is capable of exceptional turndown, both on a stage basis and with the ability to bypass entire stages. Oxygen-supply flexibility was also investigated, as this is also a key consideration for the overall flexibility of the SPOC process given the operating constraints of conventional air separation units. A boiler design concept assessment was conducted and was focused on delivering compact and constructible design. The assessment checked appropriate tube operating metal temperatures at full load and at lower operating loads, balanced against the needs of efficient coal combustion, and the resultant slagging and ash environments. Combustion testing in the 100-kWth pressurized combustion test rig at WUSTL was carried out to validate the combustion, heat flux profiles and burnout at multiple loads. Combustion parameters investigated were flame stability, fuel burnout, ash composition, radiative heat flux, and temperature profiles. The results of these tests formed the basis of a full-scale boiler design that will encompass improvements in both efficiency and flexibility over conventional oxy-combustion processes. The air separation unit flexibility was investigated, and associated cost implications were addressed. Detailed economic assessment results for a 550 MWe net power block are also provided, allowing for a comparison against the baseline NETL oxy-combustion and post combustion capture cases.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Manipulating high-temperature superconductivity by oxygen doping in Bi2Sr2CaCu2O8+δ thin flakes

Abstract Harnessing the fascinating properties of correlated oxides requires precise control of their carrier density. Compared to other methods, oxygen doping provides an effective and more direct way to tune the electronic properties of correlated oxides. Although several approaches, such as thermal annealing and oxygen migration, have been introduced to change the oxygen content, a continuous and reversible solution that can be integrated with modern electronic technology is much in demand. Here, we report a novel ionic field-effect transistor using solid Gd-doped CeO2 as the gate dielectric, which shows a remarkable carrier-density-tuning ability via electric-field-controlled oxygen concentration at room temperature. In Bi2Sr2CaCu2O8+δ (Bi-2212) thin flakes, we achieve a reversible superconductor–insulator transition by driving oxygen ions in and out of the samples with electric fields, and map out the phase diagram all the way from the insulating regime to the over-doped superconducting regime by continuously changing the oxygen doping level. Scaling analysis indicates that the reversible superconductor–insulator transition for the Bi-2212 thin flakes follows the theoretical description of a two-dimensional quantum phase transition. Our work provides a route for realizing electric-field control of phase transition in correlated oxides. Moreover, the configuration of this type of transistor makes heterostructure/interface engineering possible, thus having the potential to serve as the next-generation all-solid-state field-effect transistor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

An experimental study on round-trip efficiency of a preheating control with a medium office building

The interactions between building energy efficiency and demand response (DR) with buildings may complicate their impacts on the electricity grid and buildings, yet those interactions are not well understood. This work fills this gap by presenting an experimental study that quantifies the effects of DR on building energy efficiency. Unlike existing studies, this work 1) investigates the uncertainty levels when assessing the effects of DR; 2) studies the impact of rooftop heat pumps with direct expansion refrigerant-to-air coils on the round-trip efficiency. Specifically, we considered a medium office building (~1860 m 2 ), which is served by rooftop units, located in eastern Washington State. We performed preheating control tests during typical heating days in the year 2022 and compared the building’s energy consumption during the testing days to that during normal operation days under similar weather conditions. To understand how well those normal operation days represent the baseline for the assessment, the relationship between the energy performance of this building and weather conditions was also studied. Experimental results reveal that the round-trip efficiency (i.e., the ratio of discharging energy output from the building to charging energy input into the building) was between 0.16 and 0.92. The results show that significant energy loss may occur during the preheating process. Finally, it also suggests a significant correlation between the energy efficiency of the studied building under the preheating control and the outdoor temperature; and a highly nonlinear relationship between the zone temperature changing rate and the weather condition.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗