Flow instrumentation and operating experience in a condensing alkali metals test loop
Test method for determining condensing heat transfer characteristics of liquid alkali metals
TEST METHOD↗
SEARCH · Search NASA
Results for “test methods”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
NASA-STD-6001B Test 1 Upward Flame Propagation; Sample Length Impact on MOC Investigation
Understanding the combustion behavior of materials in the elevated oxygen environments of habitable spacecraft is of utmost importance to crew safety and mission success. Currently, certification for unrestricted flight usage of a material with respect to flammability involves passing the Upward Flame Propagation Test of NASA-STD-6001B (Test 1). This test evaluates materials in a standardized test configuration for two failure criteria: self-extinguishment within 15 cm (6 in.) and the propensity of flame propagation by means of flaming material transfer. By the NASA standard, full-length samples are 30 cm (12 in.) in length; however, factors independent of the test method such as limited material availability or various nonstandard test configurations limit the full pretest sample lengths available for test. This paper characterizes the dependence, if any, of pretest sample length on NASA-STD-6001B Test 1 results. Testing was performed using the Maximum Oxygen Concentration (MOC) Threshold Method to obtain a data set for each sample length tested. In addition, various material types, including cloth (Nomex), foam (TA-301) and solids (Ultem), were tested to investigate potential effects of test specimen types. Though additional data needs to be generated to provide statistical confidence, preliminary findings are that use of variable sample lengths has minimal impact on NASA-STD-6001B flammability performance and MOC determination.
Harper, Susana Tapia↗
Improvements in electronic component testing
Improved nondestructive test methods using infrared radiation and radioisotope tracers for seal defects and integrated circuit quality control
NONDESTRUCTIVE TESTING↗
Combined Qualification Vibration Testing and Fixed Base Modal Testing Utilizing a Fixed Based Correction Method
Vibration testing spaceflight hardware is a vital, but time consuming and expensive endeavor. Traditionally modal tests are performed at the component, subassembly, or system level, preferably free-free with mass loaded interfaces or fixed base on a seismic mass to identify the fundamental structural dynamic (modal) characteristics. Vibration tests are then traditionally performed on single-axis slip tables at qualification levels that envelope the maximum predicted flight environment plus 3 dB and workmanship in order to verify the spaceflight hardware can survive its flight environment. These two tests currently require two significantly different test setups, facilities, and ultimately reconfiguration of the spaceflight hardware. The vision of this research is to show how traditional fixed-base modal testing can be accomplished using vibration qualification testing facilities, which not only streamlines testing and reduces test costs, but also opens up the possibility of performing modal testing to untraditionally high excitation levels that provide for test-correlated finite element models to be more representative of the spaceflight hardware's response in a flight environment. This paper documents the first steps towards this vision, which is the comparison of modal parameters identified from a traditional fixed-based modal test performed on a modal floor and those obtained by utilizing a fixed based correction method with a large single-axis electrodynamic shaker driving a slip table supplemented with additional small portable shakers driving on the slip table and test article. To show robustness of this approach, the test article chosen is a simple linear weldment, whose mass, size, and modal parameters couple well with the dynamics of the shaker/slip table. This paper will show that all dynamics due to the shaker/slip table were successfully removed resulting in true fixed-base modal parameters, including modal damping, being successfully extracted from a traditional style base-shake vibration test setup.
Winkel, James P.↗
Combined Qualification Vibration Testing and Fixed Base Modal Testing Utilizing a Fixed Based Correction Method
Vibration testing spaceflight hardware is a vital, but time consuming and expensive endeavor. Traditionally modal tests are performed at the component, subassembly, or system level, preferably free-free with mass loaded interfaces or fixed base on a seismic mass to identify the fundamental structural dynamic (modal) characteristics. Vibration tests are then traditionally performed on single-axis slip tables at qualification levels that envelope the maximum predicted flight environment and workmanship in order to verify the spaceflight hardware can survive its flight environment. These two tests currently require two significantly different test setups, facilities, and ultimately reconfiguration of the spaceflight hardware. The vision of this research is to show how traditional fixed-base modal testing can be accomplished using vibration qualification testing facilities, which not only streamlines testing and reduces test costs, but also opens up the possibility of performing modal testing to untraditionally high excitation levels that provide for test-correlated finite element models to be more representative of the spaceflight hardware's response in a flight environment. This paper documents the first steps towards this vision, which is the comparison of modal parameters identified from a traditional fixed-based modal test performed on a modal floor and those obtained by utilizing a fixed based correction method with a large single-axis electrodynamic shaker driving a slip table supplemented with additional small portable shakers driving on the slip table and test article. To show robustness of this approach, the test article chosen is a simple linear weldment, whose mass, size, and modal parameters couple well with the dynamics of the shaker/slip table. This paper will show that all dynamics due to the shaker/slip table were successfully removed resulting in true fixed-base modal parameters, including modal damping, being successfully extracted from a traditional style base-shake vibration test setup.
Base-Shake↗
Structural Design Considerations for an 8-m Space Telescope
NASA's upcoming ARES V launch vehicle, with its' immerse payload capacities (both volume and mass) has opened the possibilities for a whole new paradigm of space observatories. It becomes practical to consider a monolith mirror of sufficient size to permit significant scientific advantages, both in collection area and smoothness or figure at a reasonable price. The technologies and engineering to manufacture and test 8 meter class monoliths is mature, with nearly a dozen of such mirrors already in operation around the world. This paper will discuss the design requirements to adapt an 8m meniscus mirror into a Space Telescope System, both launch and operational considerations are included. With objects this massive and structurally sensitive, the mirror design must include all stages of the process. Based upon the experiences of the Hubble Space Telescope, testing and verification at both component and integrated system levels are considered vital to mission success. To this end, two different component level test methods for gravity sag (the so call zero- gravity simulation or test mount) are proposed, with one of these methods suitable for the full up system level testing as well.
Arnold, William R. Sr.↗
Improvements in stage checkout
Test methods, equipment, and computer programs for improved quality control in space vehicle stage checkout
CHECKOUT EQUIPMENT↗
Measurement of embedment stresses in electronic modules.
Reliable test method based on special strain gauge load transducer for embedment axial stress measurement in electronic modules
STRAIN GAUGE↗
Ignition of metals and alloys in gaseous oxygen by frictional heating
The ignition of metals and alloys have been investigated by rotating the end of a hollow cylinder against an identical stationary cylinder on a common axis (frictional heating) in gaseous oxygen. A ranking criterion that measures the resistance of metals and alloys to ignition is discussed. It consists of the power per unit area required for ignition conveniently expressed as the product of contact pressure P and average linear velocity ALV. Data are presented that demonstrate that materials that are high in nickel and copper require greater P-ALV products for ignition (more resistant to ignition) than materials that are high in iron. Aluminum and titanium alloys are shown to require the lowest P-ALV products for ignition. The effects of varying surface velocity, contact pressure, coefficient of friction, and oxygen pressure on P-ALV products required for ignition are discussed. The results indicate that P-ALV product required for ignition increases as surface velocity increases, as contact pressure decreases, and as the coefficient of friction decreases. Increasing oxygen pressure will cause the P-ALV product required for ignition to decrease at low pressures and increase at high pressures. In some cases, the relative ranking of materials based on P-ALV products will also change as conditions are varied. The data presented in this paper are from a development program to determine the merits of using such a dynamic test method for ranking materials for oxygen service. The results to date have indicated that more testing is required before this method can be made into a standard test. The data presented do show some of the major parameters affecting the ignition of materials when exposed to frictional heating. The repeatability of the data at any set of conditions have not been thoroughly investigated.
Benz, F. J.↗
A simple test for the interlaminar fracture toughness of composites
A simple test method for the measurement of delamination resistance is assessed through its application to 11-ply graphite-epoxy laminates whose matrices employ the F185 and 205 resins. The F185 resin has the same base epoxy as the 205, to which liquid and solid elastomers have been added. The critical value of the mixed mode energy release rate, calculated from a closed form equation employing nominal strain measurements from the onset of edge delamination, show that addition of the elastomers to the base epoxy increases interlaminar fracture toughness. Comparison of these results with those of width-tapered double cantilever beam (WTDCB) test data for the two materials shows a similar strain energy release rate, establishing the accuracy of the novel method. Both tests are found to be needed, however, for the quantitative characterization of interlaminar fracture toughness.
Obrien, T. K.↗
Examination of the Measurement of Absorption Using the Reverberant Room Method for Highly Absorptive Acoustic Foam
The absorption coefficient for material specimens are needed to quantify the expected acoustic performance of that material in its actual usage and environment. The ASTM C423-09a standard, "Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberant Room Method" is often used to measure the absorption coefficient of material test specimens. This method has its basics in the Sabine formula. Although widely used, the interpretation of these measurements are a topic of interest. For example, in certain cases the measured Sabine absorption coefficients are greater than 1.0 for highly absorptive materials. This is often attributed to the diffraction edge effect phenomenon. An investigative test program to measure the absorption properties of highly absorbent melamine foam has been performed at the Riverbank Acoustical Laboratories. This paper will present and discuss the test results relating to the effect of the test materials' surface area, thickness and edge sealing conditions. A follow-on paper is envisioned that will present and discuss the results relating to the spacing between multiple piece specimens, and the mounting condition of the test specimen.
Absorption↗
Flying Beyond Flutter with the X-56A Aircraft
The National Aeronautics and Space Administration X-56A Multi-Utility Technology Testbed was successfully flown beyond flutter using active feedback control methods. This report discusses the flight-test methods used during envelope expansion and presents the data collected. The frequency and damping of rigid-body flight dynamic modes and the first two structural modes were estimated from the flight data. The flutter mechanism (body freedom flutter) was found to match predictions with coupling occurring between the short period and the first symmetric wing bending mode. Flights up to the instability threshold and beyond were conducted using active feedback control. Several tests were conducted in flight where the control system was disabled momentarily to observe the unstable flutter mode and then reengaged; thus, demonstrating active suppression.
Jacob Schaefer↗
System Being Developed to Measure the Rotordynamic Characteristics of Air Foil Bearings
Because of the many possible advantages of oil-free engine operation, interest in using air lubricated foil-bearing technology in advanced oil-free engine concepts has recently increased. The Oil-Free Turbomachinery Program at the NASA Glenn Research Center at Lewis Field has partially driven this recent push for oil-free technology. The program's goal of developing an innovative, practical, oil-free gas turbine engine for aeropropulsion began with the development of NASA's high-temperature solid-lubricant coating, PS304. This coating virtually eliminates the life-limiting wear that occurs during the startup and shutdown of the bearings. With practically unlimited life, foil air bearings are now very attractive to rotating machinery designers for use in turbomachinery. Unfortunately, the current knowledge base of these types of bearings is limited. In particular, the understanding of how these types of bearings contribute to the rotordynamic stability of turbomachinery is insufficient for designers to design with confidence. Recent work in oil-free turbomachinery has concentrated on advancing the understanding of foil bearings. A high-temperature fiber-optic displacement probe system and measurement method were developed to study the effects of speed, load, temperature, and other environmental issues on the stiffness characteristics of air foil bearings. Since high temperature data are to be collected in future testing, the testing method was intentionally simplified to minimize the need for expensive test hardware. The method measures the displacement induced upon a bearing in response to an applied perturbation load. The early results of these studies, which are shown in the accompanying figure, indicate trends in steady state stiffness that suggest stiffness increases with load and decreases with speed. It can be seen, even from these data, that stiffness is not expected to change by orders of magnitude over the normal operating range of most turbomachinery; a promising sign for their eventual integration into oil-free turbomachines. Planned future testing will generate similar plots for stiffness changes with temperature and geometry, as well as damping data. The data collected by this method represent a critical step toward understanding how to successfully apply foil air bearings to future oil-free turbomachinery systems.
Howard, Samuel A.↗
Qualifying Bulk Metallic Glass Gear Materials for Spacecraft Applications
NASA is evaluating bulk metallic glass (BMG) gears for extreme environment (cryogenic) applications; e.g., Europa Lander. The main purpose of this report is to recommend a quality assurance (QA) protocol for the production of consistent and reliable gear castings. Currently, there are two, separate manufacturers involved; Materion Corporation produces re-melt stock and Visser Precision Cast, Inc. produces BMG castings. Division of the existing alloy specifications document into material supplier-specific documents is proposed. Until a composition-based specification is established, processability- and performance-based methodologies may be an option during manufacturing development. It is recommended that each of the documents has a distinct focus; the processing behavior of crystalline feedstock, and the mechanical behavior of amorphous castings. The report addresses the “gray area” in QA testing between these materials suppliers by outlining an equitable division of responsibilities. The use of a number of dedicated reference dies to produce witness materials for physical and mechanical property evaluation is strongly recommended. Allocation of QA tests between screen testing of gear castings, and formal testing of witness materials, including cryogenic properties, is also proposed. The most effective suite of tests for both physical and mechanical property determination are down-selected from available national and international standards. The contents of this report create a solid basis for selection of QA tests, thereby setting the stage for negotiations between the materials suppliers and the customer.This technical paper:a) provides recommendations to advance materials specifications document JPL D-56223,Rev. A from “draft” to “preliminary” status;b) proposes division of the current document into two supplier-specific documents;c) separates testing methods by “ingots/castings” and “witness materials”;d) classifies test methodology based on “processability” and “performance”;e) assembles candidate ASTM specifications for “screen testing” and “formal testing”;f) identifies standard tests compatible with evaluation of BMG flexspline gears;g) suggests division of responsibilities for processability and performance testing; andh) addresses the QA “gray area” between production of ingots and castings.The report recommends that:a) processability- and performance-based QA methods might be used in lieu ofcompositional specifications during manufacturing development only;b) reference dies be designed for “acceptance” and “qualification” castings;c) witness materials provide physical and mechanical property data;d) formal testing be conducted at ambient and cryogenic temperatures; ande) processing/properties be correlated with compositional variations.
Hales, Stephen J.↗
Track/train dynamics test report transfer function test. Volume 1: Test
A description is presented of the transfer function test performed on an open hopper freight car loaded with 80 tons of coal. Test data and a post-test update of the requirements document and test procedure are presented. Included are a statement of the test objective, a description of the test configurations, test facilities, test methods, data acquisition/reduction operations, and a chronological test summary. An index to the data for the three test configurations (X, Y, and Z-axis tests) is presented along with test sequence, run number, test reference, and input parameters.
Vigil, R. A.↗
Initial test results with single cylinder rhombic drive Stirling engine
A brief description is given of the GPU 3-2 hardware, the test methods used, and the result of these tests. Comparison is made to unpublished data from similar hydrogen tests performed by the U.S. Army.
Cairelli, J. E.↗
Flight-test measurements of ground effect - STOL airplanes
Powered-lift STOL aircraft exhibit special aerodynamic characteristics that necessitate changes in established procedures of flight testing. Methods used in ground-effect flight testing of STOL-configured aircraft are described, with special emphasis on results obtained from tests of the YC-15 AMST prototype aircraft. Ground effect on lift and on drag is theoretically analyzed in terms of trailing vortices, bound vortex, and flight-path angle. Airspeed static source position errors are induced by ground constraint and must be considered in the data reduction. Flight-test results show a positive lift increment due to ground proximity.
Parks, E. K.↗
Composites for Advanced Space Transportation Systems (CASTS)
A summary is given of the in-house and contract work accomplished under the CASTS Project. In July 1975 the CASTS Project was initiated to develop graphite fiber/polyimide matrix (GR/PI) composite structures with 589K (600 F) operational capability for application to aerospace vehicles. Major tasks include: (1) screening composites and adhesives, (2) developing fabrication procedures and specifications, (3) developing design allowables test methods and data, and (4) design and test of structural elements and construction of an aft body flap for the Space Shuttle Orbiter Vehicle which will be ground tested. Portions of the information are from ongoing research and must be considered preliminary. The CASTS Project is scheduled to be completed in September 1983.
Davis, J. G., Jr.↗