Search NASA⌕ Search

SEARCH · Search NASA

Results for “three dimensional models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 631 records · Page 35

High temperature high velocity direct power extraction using an open-cycle oxy-combustion system

The implementation of oxy-fuel technology in fossil-fuel power plants may contribute to increased system efficiencies and a reduction of pollutant emissions. One technology that has potential to utilize the temperature of undiluted oxy-combustion flames is open-cycle magnetohydrodynamic (MHD) power generators. These systems can be configured as a topping cycle and provide high enthalpy, electrically conductive flows for direct conversion of electricity. This report presents the design and modeling strategies of a MHD combustor operating at temperatures exceeding 3000 K. Throughout the study, computational fluid dynamics (CFD) models were extensively used as a design and optimization tool. A lab-scale 60 kWth model was designed, manufactured and tested as part of this project. A fully-coupled numerical method was developed in ANSYS FLUENT to characterize the heat transfer in the system. This study revealed that nozzle heat transfer may be predicted through a 40% reduction of the semi-empirical Bartz correlation. Experimental results showed good agreement with the numerical evaluation, with the combustor exhibiting a favorable performance when tested during extended time periods. A transient numerical method was employed to analyze fuel injector geometries for the 60-kW combustor. The ANSYS FLUENT study revealed that counter-swirl inlets achieve a uniform pressure and velocity ratio when the ports of the injector length to diameter ratio (L/D) is 4. An angle of 115 degrees was found to increase distribution efficiency. The findings show that this oxy-combustion concept is capable of providing a high-enthalpy environment for seeding, in order to render the flow to be conductive. Based on previous findings, temperatures in the range of 2800-3000 K may enable magnetohydrodynamic power extraction. The heat loss fraction in this oxy-combustion system, based on CFD and analytical calculations, at optimal operating conditions, was estimated to be less than 10 percent. Furthermore, the heat transfer design removed approximately 7 MW/m2. The results observed in the lab-scale system were employed to develop a 1-MW scaled prototype. Scaling methods were based on critical design criteria found in similar systems, aimed at replicating combustion flow fields and reducing possible instabilities. A numerical simulation of the combustor wall was developed for a combined thermal steady model and static structural model. This combined model was developed predict combined stress parameters within the wall during testing conditions. Both models were developed within ANSYS FEA software package. The relative accuracy presented as well major performance parameters are discussed to assess the design's validity and ensure safety. The scaled prototype was manufactured through selective laser melting (SLM)-based additive manufacturing to reduce lead times and increase geometrical complexity. Additional CFD models were developed to optimize coolant manifold system parameters and perform a parametric study on channel geometry. An investigation on coolant manifold geometry demonstrated improvements in channel flow distribution when enlarging manifold lengths and increasing the number of tubes feeding into the flow. A three-dimensional model based on a single channel was developed to capture the effect of variable properties and thermal stratification. All cases in the simulation exhibited higher wall temperatures and lower convective coefficients than those determined through 1-D analytical equations. This implies that pressure and velocity safety factors must be implemented during system operation. Overall, the findings made in this investigation are thought to be of value to researchers and industrial practitioners when designing oxy-fuel direct power extraction systems operating at temperatures exceeding 3000 K. In addition to this, the implementation of the developed technology at pilot and commercial scales could result in a significant improvement in the efficiencies of heritage and next-generation power cycles.

03 NATURAL GAS↗

Fission Product Transport in TRISO Particles and Pebbles

This document demonstrates completion of the goals described in the technical narrative of the FOA project titled: ”Modeling and Simulation Development Pathways to Accelerating KP-FHR Licensing” regarding fission product transport in the Kairos-proposed fuel pebble by INL and Kairos Power. Showcased in this report are code developments and simulations in BISON that extend the state of the art in computation and understanding of fission product transport in a TRISO fuel particle and pebble. These enhancements lay the foundation for making predictions of fission product transport that can be used as input in the fuel licensing process. This was achieved by installing existing fuel material models originally used in PARFUME, developing a new failure probability method that is efficient and multi-dimensional, employing material homogenization, and expanding verification and validation simulations to demonstrate the efficacy of the work. All this work is leveraged to spotlight the main deliverable; a three-dimensional model and corresponding demonstration simulation of a pebble, which will serve as the starting point for models used to predict fission product release.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Kp dependent equatorial electric field model

A new model of the earth's electric field in the equatorial plane has been constructed. While many models have been proposed, most of these have had serious shortcomings. They either have only a few parameters and cannot hope to match even large scale variations in the real field, or they are too complex to be suitable starting points for constructing time dependent three dimensional models which include inductive fields. Also, few previous models have a continuous functional dependence upon magnetic disturbance levels. The new model uses only a dozen parameters and yet fits many of the known dependences upon radial distance, local time, and magnetic disturbance level. One of the roles of electric field models is to predict and understand the motion of charged particles. Models like this one which are based upon a time dependent scalar potential can greatly help in the understanding of the motion of equatorial particles during the time periods between substorms.

Mcilwain, C. E.↗

Fission Product Transport in TRISO Particles and Pebbles

This document demonstrates completion of the goals described in the technical narrative of the FOA project titled: ”Modeling and Simulation Development Pathways to Accelerating KP-FHR Licensing” regarding fission product transport in the Kairos-proposed fuel pebble by INL and Kairos Power. Showcased in this report are code developments and simulations in BISON that extend the state of the art in computation and understanding of fission product transport in a TRISO fuel particle and pebble. These enhancements lay the foundation for making predictions of fission product transport that can be used as input in the fuel licensing process. This was achieved by installing existing fuel material models originally used in PARFUME, developing a new failure probability method that is efficient and multi-dimensional, employing material homogenization, and expanding verification and validation simulations to demonstrate the efficacy of the work. All this work is leveraged to spotlight the main deliverable; a three-dimensional model and corresponding demonstration simulation of a pebble, which will serve as the starting point for models used to predict fission product release.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Determining inclinations of active galactic nuclei via their narrow-line region kinematics. II. Correlation with observed properties

Active galactic nuclei (AGNs) are axisymmetric systems to first order; their observed properties are likely strong functions of inclination with respect to our line of sight, yet the specific inclinations of all but a few AGNs are generally unknown. By determining the inclinations and geometries of nearby Seyfert galaxies using the kinematics of their narrow-line regions (NLRs) and comparing them with observed properties, we find strong correlations between inclination and total hydrogen column density, infrared color, and Hβ FWHM. These correlations provide evidence that the orientation of AGNs with respect to our line of sight affects how we perceive them beyond the Seyfert 1/2 dichotomy. They can also be used to constrain three-dimensional models of AGN components such as the broad-line region and torus. Additionally, we find weak correlations between AGN luminosity and several modeled NLR parameters, which suggests that the NLR geometry and kinematics are dependent to some degree on the AGN's radiation field.

79 ASTRONOMY AND ASTROPHYSICS↗

AN OPTICAL-INFRARED STUDY OF THE YOUNG MULTIPOLAR PLANETARY NEBULA NGC 6644

High-resolution Hubble Space Telescope imaging of the compact planetary nebula NGC 6644 has revealed two pairs of bipolar lobes and a central ring lying close to the plane of the sky. From mid-infrared imaging obtained with the Gemini Telescope, we have found a dust torus which is oriented nearly perpendicular to one pair of the lobes. We suggest that NGC 6644 is a multipolar nebula and construct a three-dimensional model that allows the visualization of the object from different lines of sight. These results suggest that NGC 6644 may have similar intrinsic structures as other multipolar nebulae and the phenomenon of multipolar nebulosity may be more common than previously believed.

79 ASTRONOMY AND ASTROPHYSICS↗

Up-date of traveling wave tube improvements

NASA research in the area of traveling wave tube technology is reviewed, with emphasis on the basic physics of guns and collectors and a computer model for the interaction between the electron beam and the RF circuit. The design of a multistage depressed collector, capable of multiplying tube efficiency by a factor of two or more, is presented; one such design has been adopted for commercial traveling wave tube production. A three-dimensional model of electron trajectories toward the collector also receives attention, as does the problem of RF circuit losses.

Buck, E.↗

The amphibian egg as a model system for analyzing gravity effects

Amphibian eggs provide several advantageous features as a model system for analyzing the effects of gravity on single cells. Those features include large size, readily tracked intracellular inclusions, and ease of experimental manipulation. Employing novel gravity orientation as a tool, a substantial data base is being developed. That information is being used to construct a three-dimensional model of the frog (Xenopus laevis) egg. Internal cytoplasmic organization (rather than surface features) are being emphasized. Several cytoplasmic compartments (domains) have been elucidated, and their behavior in inverted eggs monitored. They have been incorporated into the model, and serve as a point of departure for further inquiry and speculation.

Malacinski, G. M.↗

Assessment of the Neutronic and Fuel Cycle Performance of the Transatomic Power Molten Salt Reactor Design

This report presents results from a collaboration between Transatomic Power Corporation (TAP) and Oak Ridge National Laboratory (ORNL) to provide neutronic and fuel cycle analysis of the TAP core design through the Department of Energy Gateway for Accelerated Innovation in Nuclear (GAIN) Nuclear Energy Voucher program. The TAP concept is a molten salt reactor using configurable zirconium hydride moderator rod assemblies to shift the neutron spectrum in the core from mostly epithermal at beginning of life to thermal at end of life. Additional developments in the ChemTriton modeling and simulation tool provide the critical moderator-to-fuel ratio searches and time-dependent parameters necessary to simulate the continuously changing physics in this complex system. The implementation of continuous-energy Monte Carlo transport and depletion tools in ChemTriton provide for full-core three-dimensional modeling and simulation. Results from simulations with these tools show agreement with TAP-calculated performance metrics for core lifetime, discharge burnup, and salt volume fraction, verifying the viability of reducing actinide waste production with this concept. Additional analyses of mass feed rates and enrichments, isotopic removals, tritium generation, core power distribution, core vessel helium generation, moderator rod heat deposition, and reactivity coeffcients provide additional information to make informed design decisions. This work demonstrates capabilities of ORNL modeling and simulation tools for neutronic and fuel cycle analysis of molten salt reactor concepts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evidence for an interstellar dust filament in the outer heliosheath

A recently discovered filament of polarized starlight that traces a coherent magnetic field is shown to have several properties that are consistent with an origin in the outer heliosheath of the heliosphere: (1) the magnetic field that provides the best fit to the polarization position angles is directed toward ℓ = 357.°3, b = 17.°0 (±11.°2); this direction is within 6.°7 ± 11.°2 of the observed upwind direction of the flow of interstellar neutral helium gas through the heliosphere. (2) The magnetic field is ordered; the component of the variation of the polarization position angles that can be attributed to magnetic turbulence is ±9.°6. (3) The axis of the elongated filament can be approximated by a line that defines an angle of 80° ± 14° with the plane that is formed by the interstellar magnetic field (ISMF) vector and the vector of the inflowing neutral gas (the BV plane). We propose that this polarization feature arises from aligned interstellar dust grains in the outer heliosheath where the interstellar plasma and magnetic field are deflected around the heliosphere. This interpretation suggests that the polarization is seen where stream lines of the flow and the draped ISMF lines are approximately parallel to each other and perpendicular to the sightline. An ordered magnetic field is required so that grain alignment is not disrupted during the interaction. The filament location is consistent with dust plumes previously predicted to form around the heliosphere. The proposed outer heliosheath location of the polarizing grains can be tested with three-dimensional models that track torques on asymmetric dust grains as they propagate through the heliosheath plasma, and using these models to evaluate grain alignment and the asymmetric extinction of the grains.

79 ASTRONOMY AND ASTROPHYSICS↗

Enhanced geometric capabilities for the transient analysis code T-ReX and its application to simulating TREAT experiments

Here, advances in computational architecture have prompted a resurgence in the simulation of reactor transients from first principles. Most codes are unable to simulate transient events with complex models, and require numerous approximations. The code T-ReX (Transient-Reactor eXperiment simulator), an extensive update to TDKENO, has been developed as a transient analysis tool with few geometric limitations and minimal theoretical approximations. T-ReX achieves this by employing the Improved Quasi-Static (IQS) method to solve the time dependent Boltzmann transport equation with explicit representation of delayed neutrons. The primary change in T-ReX relative to TDKENO is the incorporation of a modified version of the Monte Carlo code KENO-VI to calculate the flux shape and model the geometry of a problem. Using KENO-VI to model systems allows exact representation of the geometry. The changes to T-ReX are verified by comparison of solutions to computational benchmark problems found with a previous version of TDKENO that made use of KENO V.a, and several other codes with time-dependent capabilities. In addition, a three-dimensional model of the Transient Reactor Test Facility (TREAT) core at the Idaho National Laboratory (INL) is constructed with KENO-VI, and used to validate T ReX. T-ReX produces results that agree with benchmark problems, and are in better agreement with TREAT experimental data than TDKENO.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

RAMA Surveillance Capsule and Component Activation Analyses

This paper presents the calculated-to-measured ratios associated with the application of the RAMA Fluence Methodology software to light water reactor surveillance capsule and reactor component activation evaluations. Comparisons to measurements are performed for pressurized water reactor and boiling water reactor surveillance capsule activity specimens from seventeen operating light water reactors. Comparisons to measurements are also performed for samples removed from the core shroud, top guide, and jet pump brace pads from two reactors. In conclusion: The flexible geometry modeling capabilities provided by RAMA, combined with the detailed representation of operating reactor history and anisotropic scattering detail, produces accurate predictions of the fast neutron fluence and neutron activation for BWR and PWR surveillance capsule geometries. This allows best estimate RPV fluence to be determined without the need for multiplicative bias corrections. The three-dimensional modeling capability in RAMA provides an accurate estimate of the fast neutron fluence for regions far removed from the core mid-plane elevation. The comparisons to activation measurements for various core components indicate that the RAMA predictions are reasonable, and notably conservative (i.e., C/M ratios are consistently greater than unity). It should be noted that in the current evaluations, the top and bottom fuel regions are represented by six inch height nodes. As a result, the leakage-induced decrease in power near the upper and lower edges of the core are not well represented in the current models. More precise predictions of fluence for components that lie above and below the core boundaries could be obtained if the upper and lower fuel nodes were subdivided into multiple axial regions with assigned powers that reflect the neutron leakage at the top and bottom of the core. This use of additional axial sub-meshing at the top and bottom of the core is analogous to the use of pin-wise meshing in peripheral bundles to accurately represent radial leakage effects. The representation of thermal neutron fluence and activations are found to be reasonably accurate and consistently conservative, as demonstrated by comparison to the reactor component thermal neutron reaction activation measurements. Further improvement in the comparisons to measurements could be achieved by exploring the impact of enhanced sub-meshing of the geometry near the components of interest. The mesh densities utilized in the current evaluation are consistent with the mesh requirements for high energy neutron transport. The substantially shorter transport lengths for thermal neutrons relative to high energy neutrons suggests that localized regions of finer meshing are needed in the vicinity of those reactor components requiring thermal neutron fluence evaluations. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

ROTATING MOTIONS AND MODELING OF THE ERUPTING SOLAR POLAR-CROWN PROMINENCE ON 2010 DECEMBER 6

A large polar-crown prominence composed of different segments spanning nearly the entire solar disk erupted on 2010 December 6. Prior to the eruption, the filament in the active region part split into two layers: a lower layer and an elevated layer. The eruption occurs in several episodes. Around 14:12 UT, the lower layer of the active region filament breaks apart: One part ejects toward the west, while the other part ejects toward the east, which leads to the explosive eruption of the eastern quiescent filament. During the early rise phase, part of the quiescent filament sheet displays strong rolling motion (observed by STEREO-B) in the clockwise direction (viewed from east to west) around the filament axis. This rolling motion appears to start from the border of the active region, then propagates toward the east. The Atmospheric Imaging Assembly (AIA) observes another type of rotating motion: In some other parts of the erupting quiescent prominence, the vertical threads turn horizontal, then turn upside down. The elevated active region filament does not erupt until 18:00 UT, when the erupting quiescent filament has already reached a very large height. We develop two simplified three-dimensional models that qualitatively reproduce the observed rolling and rotating motions. The prominence in the models is assumed to consist of a collection of discrete blobs that are tied to particular field lines of a helical flux rope. The observed rolling motion is reproduced by continuous twist injection into the flux rope in Model 1 from the active region side. Asymmetric reconnection induced by the asymmetric distribution of the magnetic fields on the two sides of the filament may cause the observed rolling motion. The rotating motion of the prominence threads observed by AIA is consistent with the removal of the field line dips in Model 2 from the top down during the eruption.

79 ASTRONOMY AND ASTROPHYSICS↗

Comprehensive computer model for magnetron sputtering. II. Charged particle transport

Discharges for magnetron sputter thin film deposition systems involve complex plasmas that are sensitively dependent on magnetic field configuration and strength, working gas species and pressure, chamber geometry, and discharge power. The authors present a numerical formulation for the general solution of these plasmas as a component of a comprehensive simulation capability for planar magnetron sputtering. This is an extensible, fully three-dimensional model supporting realistic magnetic fields and is self-consistently solvable on a desktop computer. The plasma model features a hybrid approach involving a Monte Carlo treatment of energetic electrons and ions, along with a coupled fluid model for thermalized particles. Validation against a well-known one-dimensional system is presented. Various strategies for improving numerical stability are investigated as is the sensitivity of the solution to various model and process parameters. In particular, the effect of magnetic field, argon gas pressure, and discharge power are studied.

36 MATERIALS SCIENCE↗

Object Creation and Human Factors Evaluation for Virtual Environments

The main objective of this project is to provide test objects for simulated environments utilized by the recently established Army/NASA Virtual Innovations Lab (ANVIL) at Marshall Space Flight Center, Huntsville, Al. The objective of the ANVIL lab is to provide virtual reality (VR) models and environments and to provide visualization and manipulation methods for the purpose of training and testing. Visualization equipment used in the ANVIL lab includes head-mounted and boom-mounted immersive virtual reality display devices. Objects in the environment are manipulated using data glove, hand controller, or mouse. These simulated objects are solid or surfaced three dimensional models. They may be viewed or manipulated from any location within the environment and may be viewed on-screen or via immersive VR. The objects are created using various CAD modeling packages and are converted into the virtual environment using dVise. This enables the object or environment to be viewed from any angle or distance for training or testing purposes.

Lindsey, Patricia F.↗

Modeling SARS-CoV-2 proteins in the CASP-commons experiment

Critical Assessment of Structure Prediction (CASP) is an organization aimed at advancing the state of the art in computing protein structure from sequence. In the spring of 2020, CASP launched a community project to compute the structures of the most structurally challenging proteins coded for in the SARS-CoV-2 genome. Forty-seven research groups submitted over 3000 three-dimensional models and 700 sets of accuracy estimates on 10 proteins. The resulting models were released to the public. CASP community members also worked together to provide estimates of local and global accuracy and identify structure-based domain boundaries for some proteins. Subsequently, two of these structures (ORF3a and ORF8) have been solved experimentally, allowing assessment of both model quality and the accuracy estimates. Models from the AlphaFold2 group were found to have good agreement with the experimental structures, with main chain GDT_TS accuracy scores ranging from 63 (a correct topology) to 87 (competitive with experiment).

59 BASIC BIOLOGICAL SCIENCES↗

Mixing and Transport in the Solar Nebula

Boss & Vanhala (2000, 2001) prepared reviews of triggered collapse and injection models, using Prudence Foster's finite differences code at very high spatial resolution (440 x 1440 cells) to demonstrate the convergence of the R-T fingers in triggered injection models. A two dimensional hydrodynamical calculation with unprecedentedly high spatial resolution (960 x 2880 zones, or almost 3 million grid points) demonstrated that it suitable shock front can both trigger the collapse of an otherwise stable presolar cloud, and inject shock front particles into the collapsing cloud through the formation of what become Rayleigh-Taylor fingers of compressed fluid layers falling into the gravitational potential well of the growing protostar. These calculations suggest that heterogeneity derived from these R-T fingers will persist down to the scale of their injection onto the surface of the solar nebula. Haghighipour developed a numerical code capable of calculating the orbital evolution of dust grains of varied sizes in a gaseous nebula, subject to Epstein and Stokes drag as well as the self-gravity of the disk. In collaboration with the PI and George W. Wetherill, Haghighipour has been involved in development of a new idea on the possibility of rapid formation of ice giant planets via the disk instability mechanism. Haghighipour studied the stability of a five-body system consisting of the Sun and four protoplanets by numerically integrating their equations of motions. Using Levison and Duncan s SWIFT integrator, Haghighipour showed that, depending on the orbital parameters of the bodies, such a system can be stable for 0.1-10 Myr. Time periods of 1 Myr or more are long enough to be consistent with the time scale proposed for the formation of giant planets by the disk instability mechanism and the photoevaporation of the gaseous envelopes of the outermost protoplanets by a nearby OB star, resulting in the formation of ice giant planets. The PI has used his three dimensional models of marginally gravitationally unstable disks to study the preservation of isotopic heterogeneity in evolving protoplanetary disks. Such heterogeneity might arise from the infall onto the disk s surface of solids processed in the X-wind region of the disk, or derived from stellar nucleosynthesis and injected by R-T fingers. The technique used consists of solving a color equation, identical to the gas continuity equation, which follows the time evolution in three space dimensions of an arbitrarily placed initial color field, i.e., a dye inserted the disk. The models show that significant concentrations of color could persist for time periods of about a thousand years or more, even in the most dynamically active region of such a disk. Such a time period might be long enough for solids to coagulate and grow to significant sizes while retaining the isotopic signature of their birth region in the nebula.

Boss, Alan P.↗

Report on the LLNL Global Seismic Waveform Tomography Modeling Project

Earth models have important applications for seismic event monitoring including the location and characterization of potential underground nuclear tests. Seismic waves generated by earthquakes and man-made events are altered by variations in Earth’s subsurface properties; and these distortions effect the arrival times of energy packets (phases) and obscure the characteristics of the original energy source (event mechanism). Three-dimensional models of Earth’s seismic properties can help explain and predict the distortions to the seismic wavefield and reveal the properties of a source that generated the waves, including the event location using the model-predicted timing of the phases and source mechanism using the modelpredicted waveform characteristics.

58 GEOSCIENCES↗