Search NASA⌕ Search

SEARCH · Search NASA

Results for “BATTERY CELL MODELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Bifunctionally Graded Electrode Supported SOFC Modeling and Computational Thermal Fluid Analysis for Experimental Design

A comprehensive 3D computational fluid dynamics (CFD) model is developed for a bi-electrode supported cell (BSC) solid oxide fuel cell (SOFC). The model includes complicated transport phenomena of mass/heat transfer, charge (electron and ion) migration, and electrochemical reactions. The uniqueness of the modeling study is that functionally graded porous electrode property is taken into account, including not only linear but also nonlinear porosity distributions. The model is validated using experimental data from open literature. Numerical results indicate that BSC performance is strongly dependent on both operating conditions and porous microstructure distributions of electrodes. Using the proposed fuel/gas feeding design, the uniform hydrogen distribution within the porous anode is achieved; the oxygen distribution within the cathode is dependent on porous microstructure distributions as well as pressure loss conditions. Simulation results also show that fairly uniform temperature distribution can be obtained with the proposed fuel/gas feeding design. This modeling work can provide a pre-experimental analysis and guide experimental designs for BSC test.

carbon sequestration↗

Electrochemical Characterization of Degradation Modes of High-Voltage Li x Ni 0.33 Mn 0.33 Co 0.33 O 2 Electrodes

While deeply charged high-voltage cathodes can improve battery energy density, understanding and preventing any accelerated cell degradation is crucial to practical success. Here, to analyze the degradation of LiNi x Mn y Co 1–x–y O 2 (NMC) type material charged to 4.3 and 4.5 V, a physics-based model is applied to cycling data to obtain parameter estimates indicative of degradation modes, which are validated by simple electrochemical measurements and further interpreted by materials characterization. Growth rates of interfacial impedance and active material loss are greater at 4.5 V, as might be expected. However, when charged to 4.5 V, degradation rates are initially lower at a cycling C-rate of 1.0 C than at 0.5 C. Once degradation mode changes are quantified, simulations evaluate the contribution of individual degradation mode to performance losses and provide estimates of the energy-power correlation (Ragone plots) of cells after cycling.

25 ENERGY STORAGE↗

Robust Scheduling of Microgrids Considering Unintentional Islanding Conditions

This paper proposes a robust scheduling model for microgrids considering the stochastic unintentional islanding conditions. The proposed model minimizes the total operating cost of the microgrid by efficiently coordinating the supply of power from local distributed energy resources and the main grid. To capture the prevailing uncertainties in renewable generation and demand as well as unintentional islanding conditions, a two-stage adaptive robust optimization model is formulated to minimize the total operating cost under the worst realization of the modeled uncertainties. The column and constraint generation (C&CG) method is used to solve the problem in an iterative manner. The solution of the proposed scheduling model ensures robust microgrid operation in consideration of all possible realization of renewable generation, demand and unintentional islanding condition. Numerical simulations on a microgrid consisting of a wind turbine, a PV panel, a fuel cell, two micro-turbines, a diesel generator and a battery demonstrate the effectiveness of the proposed approach.

Liu, Guodong↗

Energy Arbitrage: Comparison of Options for use with LWR Nuclear Power Plants

Arbitrage is the opportunistic buying and selling of a commodity during local pricing valleys and peaks respectively to maximize economic value. This report evaluates options for energy arbitrage integrated with existing light water reactor (LWR) nuclear power plants (NPPs) where nuclear energy could be stored in a variety of forms and later recovered to generate electrical power during periods when grid electricity demand and pricing are high. The forms of energy storage examined in this report include the potential value of batteries, hydrogen, and thermal energy storage for coupling with nuclear power. Various large demand response options are also analyzed, including the production of liquid nitrogen via air separation and liquefaction, liquefaction of hydrogen, compressed hydrogen, and the cryogenic capture of CO2. Demand response refers to dispatchable loads that can cycle up or down depending on-grid electricity demand to aid in balancing the grid. Large demand response options could dispatch to aid nuclear power stations in avoiding power turndowns by providing an alternate disposition for electrical energy by producing marketable products (e.g., liquid nitrogen, hydrogen, or captured CO2). Static conditions were chosen and analyzed in this report for each option. Dynamic operation or optimization of energy arbitrage or demand response are out of scope for this report. The analysis is based on storage systems with discharge capacities of 500 MW for which various durations of storage and costs of charging (electricity cost) are examined. While the value of thermal energy to an industrial user for flexible plant operations has been previously proven as a business case, this report evaluates costs of hydrogen energy storage and leading thermal energy storage options, and large demand response loads that could be integrated with LWRs in comparison to utility-scale battery storage for use of off-peak nuclear energy. Compilation of this information will be used by the Idaho National Laboratory (INL) RAVEN/HERON systems integration and economics tool to evaluate thermal energy dispatch to industrial users. Relative ranking of energy storage options was done using a levelized cost of storage (LCOS) metric which calculates a rough breakeven cost for the system, taking into account the capital and operating costs as well as the revenue from arbitrage. Table ES1 below shows the LCOS for each of the energy storage options considered. First, in the table, lithium iron (Fe) phosphate batteries are listed as the base case for comparison against the other options. Next is hydrogen storage where most of the hydrogen analyses assumed the hydrogen to be produced using solid oxide electrolytic cell (SOEC) high temperature steam electrolysis (HTSE). The others used existing models of polymer electrolyte membrane (PEM) low temperature electrolysis to produce hydrogen. HTSE performance parameters and costs were taken from existing INL models. Various means were assumed to convert the hydrogen to electricity, including PEM fuel cells (FCs) and a gas turbine mixed in a 30 vol% mixture with natural gas. Physical storage (pressure vessels) and geological storage (natural underground features) were used to store the hydrogen as noted. Geological storage is more economical, but the locations are limited because of the requirement for pre-existing geological formations that will support storage. Thermal energy storage (TES) options were also analyzed including electro-thermal energy storage (ETES) and four different liquid sensible heat TES storage media as noted (Hitec, Hitec XL, Therminol-66, and Dowtherm A). The ETES process considered was modified using existing public documentation on an Echogen process and uses a separate supercritical CO2 charge and discharge cycle with sand as the heat storage media.

25 ENERGY STORAGE↗

Growth mechanism and magnetic and electrochemical properties of Na{sub 0.44}MnO{sub 2} nanorods as cathode material for Na-ion batteries

Nanorods of Na{sub 0.44}MnO{sub 2} are a promising cathode material for Na-ion batteries due to their large surface area and single crystalline structure. We report the growth mechanism of Na{sub 0.44}MnO{sub 2} nanorods via solid state synthesis and their physical properties. The structure and the morphology of the Na{sub 0.44}MnO{sub 2} nanorods are investigated by X-ray diffraction (XRD), scanning and tunneling electron microscopy (SEM and TEM), and energy-dispersive X-ray (EDX) techniques. The growth mechanism of the rods is investigated and the effects of vapor pressure and partial melting of Na-rich regions are discussed. The magnetic measurements show an antiferromagnetic phase transition at 25 K and the μ{sub eff} is determined as 3.41 and 3.24 μ{sub B} from the χ–T curve and theoretical calculation, respectively. The electronic configuration and spin state of Mn{sup 3+} and Mn{sup 4+} are discussed in detail. The electrochemical properties of the cell fabricated using the nanorods are investigated and the peaks in the voltammogram are attributed to the diffusion of Na ions from different sites. Na intercalation process is explained by one and two Margules and van Laar models. - Highlights: • We synthesized Na{sub 0.44}MnO{sub 2} nanorods via a simple solid state reaction technique. • Our studies show that excess Na plays a crucial role in the nanorod formation. • Magnetization measurements show that Mn{sup 3+} ions are in LS and HS states. • The electrochemical properties of the cell fabricated using the nanorods are investigated. • Na intercalation process is explained by one and two Margules and van Laar models.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Operational optimization for multi-functional charging station with electric and hydrogen-powered vehicles

The rapid adoption of electric vehicles (EVs) and hydrogen fuel cell vehicles (HFCVs), combined with global efforts to reduce carbon emissions, has accelerated the development of EV charging and hydrogen refueling stations. In response to this demand, this paper introduces the concept of Multi-Functional Charging Station (MFCS) that integrates power generation, EV charging, battery swapping, and hydrogen refueling. A comprehensive operational model is developed for the MFCS that couples electricity and hydrogen conversion and storage technologies to enhance infrastructure utilization and improve overall system efficiency. The model also considers multiple revenue streams, including participation in energy and ancillary markets. To validate the effectiveness of the proposed model and evaluate its performance, a series of numerical experiments are conducted with different charger numbers, different electricity purchase limits, and different charger allocations. Numerical results demonstrate that shared charger configurations can lead to 8.11 % improvement in operational profit by improving resource utilization and reducing the number of depleted batteries at the end of operations compared to allocated charger setups. By varying the number of chargers, sensitivity analysis identifies diminishing marginal returns beyond about 45 chargers, suggesting it as an optimal sizing point under current settings. The integration of electricity and hydrogen conversion is also explored under scenarios with limited external electricity purchases. In conclusion, these findings indicate that optimizing charger allocation and energy management can significantly enhance station productivity and profitability, ultimately supporting the broader adoption of electrified and hydrogen-based transportation solutions.

Charging station↗

In Situ Raman Mapping of Si Island Electrodes and Stress Modeling as a Function of Lithiation and Size

Si is known for cracking and delamination during electrochemical cycling of a battery due to the large volume change associated with Li insertion and extraction. However, it has been found experimentally that patterned Si island electrodes that are 200 nm thick and less than 7 μm wide can deform in a purely elastic manner. Inspired by this, we performed in situ Raman stress characterization of model poly-crystalline Si island electrodes using an electrochemical cell coupled with an immersion objective lens and designed for a short working distance. A 5 μm wide Si island electrode showed a parabolic stress profile during lithiation, while for a 15 μm Si island electrode, a stress plateau in the center of the electrode was observed. A continuum model with coupled electro-chemo-mechanical (ECM) physics was established to understand the stress measurement. A qualitative agreement was reached between modeling and experimental data, and the critical size effect could be explained by the Li diffusive flux as governed by competition between the Li concentration and hydrostatic stress gradients. Below the critical size, the stress gradient drives Li toward the edges, where the electrode volume is free to expand, while above the critical size, the stress plateau inhibits Li diffusion to the edge and forces destructive stress relief by cracking. Furthermore, this work represents a promising methodology for in situ characterization of ECM coupling in battery electrodes, with suggestions provided for further improvement.

25 ENERGY STORAGE↗

Gas-mediated defect engineering in earth-abundant Mn-rich layered oxides for non-aqueous sodium-based batteries

Gases are often by-products of battery materials during cell formation and degradation, affecting the cycle life and safety of rechargeable batteries. However, understanding gas-mediated (electro)-chemical reactions and nanoscale structural transformations during the synthesis of battery electrode materials remains challenging because of the lack of suitable characterization routes and the complexity of the interplay between thermodynamics and kinetics. Here, in this study, we use operando synchrotron X-ray diffraction, in situ transmission X-ray microscopy and multiscale modelling to elucidate the reaction pathways and microstructural defect development of earth-abundant Mn-rich layered oxides as positive electrode materials for sodium-based batteries. In particular, we demonstrate the dominant role of CO 2 over O 2 and H 2 O (g) in modulating the competition between entropy and enthalpy during solid-state synthesis. Using Ni 0.25 Mn 0.75 CO 3 as a model precursor, we reveal that CO 2 generation favours the formation of entropy-driven metastable intermediates, suppresses closed pore/nanovoids formation and decreases chemical heterogeneity and residual lattice strain of Mn-rich layered oxides during the synthesis. This result motivates a fast-sintering strategy to promote CO 2 release, which ultimately leads to improved chemo-mechanical and electrochemical stability of the Mn-rich positive electrodes when tested in non-aqueous Na metal coin cells.

36 MATERIALS SCIENCE↗

Linking Pressure to Electrochemical Evolution in Solid-State Conversion Cathode Composites

Conversion-type cathodes, such as sulfur, FeS 2 , and FeF 3 , offer high theoretical capacities in solid-state lithium batteries but are hindered by substantial volume changes during cycling, leading to interfacial contact loss, crack formation, and microstructural degradation. Here, we investigate the relationships between electrochemical, mechanical, and structural evolution in solid-state electrode composites with these three active materials. Using real-time stack-pressure monitoring, synchrotron X-ray absorption spectroscopy, and electrokinetic modeling, we elucidate how stress evolution is linked to reversible and irreversible redox reactions. Nonlinear stack pressure evolution in cells with sulfur, FeS 2 , and FeF 3 electrode composites is found to arise from material-specific volume changes, the balance of volume change between the working and counter electrode, and the formation of distinct reaction intermediates. The three materials exhibit distinct stack pressure evolution, which is closely related to the different reaction processes in the materials, as demonstrated with X-ray absorption spectroscopy measurements. Through mesoscale modeling, we relate the experimental measurements to species evolution at the particle scale and track the dynamic coexistence of intermediate phases. Our findings highlight the importance of designing for volume changes of a given active material in solid-state battery systems.

batteries↗

Microgrid Reliability Modeling and Battery Scheduling Using Stochastic Linear Programming

This paper describes the introduction of stochastic linear programming into Operations DER-CAM, a tool used to obtain optimal operating schedules for a given microgrid under local economic and environmental conditions. This application follows previous work on optimal scheduling of a lithium-iron-phosphate battery given the output uncertainty of a 1 MW molten carbonate fuel cell. Both are in the Santa Rita Jail microgrid, located in Dublin, California. This fuel cell has proven unreliable, partially justifying the consideration of storage options. Several stochastic DER-CAM runs are executed to compare different scenarios to values obtained by a deterministic approach. Results indicate that using a stochastic approach provides a conservative yet more lucrative battery schedule. Lower expected energy bills result, given fuel cell outages, in potential savings exceeding 6percent.

25 ENERGY STORAGE↗

Challenging Practices of Algebraic Battery Life Models through Statistical Validation and Model Identification via Machine-Learning

Various modeling techniques are used to predict the capacity fade of Li-ion batteries. Algebraic reduced-order models, which are inherently interpretable and computationally fast, are ideal for use in battery controllers, technoeconomic models, and multi-objective optimizations. For Li-ion batteries with graphite anodes, solid-electrolyte-interphase (SEI) growth on the graphite surface dominates fade. This fade is often modeled using physically informed equations, such as square-root of time for predicting solvent-diffusion limited SEI growth, and Arrhenius and Tafel-like equations predicting the temperature and state-of-charge rate dependencies. In some cases, completely empirical relationships are proposed. However, statistical validation is rarely conducted to evaluate model optimality, and only a handful of possible models are usually investigated. This article demonstrates a novel procedure for automatically identifying reduced-order degradation models from millions of algorithmically generated equations via bi-level optimization and symbolic regression. Identified models are statistically validated using cross-validation, sensitivity analysis, and uncertainty quantification via bootstrapping. On a LiFePO 4 /Graphite cell calendar aging data set, automatically identified models utilizing square-root, power law, stretched exponential, and sigmoidal functions result in greater accuracy and lower uncertainty than models identified by human experts, and demonstrate that previously known physical relationships can be empirically "rediscovered" using machine learning.

25 ENERGY STORAGE↗

Oriented porous LLZO 3D structures obtained by freeze casting for battery applications

All solid-state lithium batteries are, potentially, higher energy density and safer alternatives to conventional lithium-ion batteries (LIBs). These are particularly attractive characteristics for large-scale applications such as electric vehicles and grid energy storage systems. However, the thin film deposition techniques used to make current devices are not readily scalable, and result in low areal capacities, which translate to low practical energy densities. To overcome these deficiencies, it is necessary to design thicker electrodes similar to what are used in LIBs (30–100 μm), in which the active material is composited with an ionic conductor and an electronically conducting additive, to overcome transport limitations. In this paper, we propose a method for making such an electrode, starting with a porous scaffold, i.e. Li 7 La 3 Zr 2 O 12 (LLZO), made by freeze casting, which is then infiltrated with the active material LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC-622) and other components. The freeze casting technique results in the formation of oriented channels with low tortuosity, which run roughly parallel to the direction of the current. The scaffolds were characterized with synchrotron X-ray micro-tomography for structural analysis, as well as synchrotron X-ray fluorescence to map the elemental distribution in the infiltrated composite. A hybrid half-cell was constructed and cycled as proof of principle, and it showed good stability. In addition, a bilayer structure consisting of a porous layer combined with a dense LLZO film was successfully made as a prototype of an all solid-state battery. Finally, a mathematical model was established to propose optimized scaffold structures for battery performance.

25 ENERGY STORAGE↗

A One-Dimensional Stack Model for Redox Flow Battery Analysis and Operation

Current redox flow battery (RFB) stack models are not particularly conducive to accurate yet high-throughput studies of stack operation and design. To facilitate system-level analysis, we have developed a one-dimensional RFB stack model through the combination of a one-dimensional Newman-type cell model and a resistor-network to evaluate contributions from shunt currents within the stack. Inclusion of hydraulic losses and membrane crossover enables constrained optimization of system performance and allows users to make recommendations for operating flow rate, current densities, and cell design given a subset of electrolyte and electrode properties. Over the range of experimental conditions explored, shunt current losses remain small, but mass-transfer losses quickly become prohibitive at high current densities. Attempting to offset mass-transfer losses with high flow rates reduces system efficiency due to the increase in pressure drop through the porous electrode. The development of this stack model application, along with the availability of the source MATLAB code, allows for facile approximation of the upper limits of performance with limited empiricism. This work primarily presents a readily adaptable tool to enable researchers to perform either front-end performance estimates based on fundamental material properties or to benchmark their experimental results.

Barton, John L. (ORCID:0000000225729127)↗

Artificial intelligence inferred microstructural properties from voltage–capacity curves

Abstract The quantification of microstructural properties to optimize battery design and performance, to maintain product quality, or to track the degradation of LIBs remains expensive and slow when performed through currently used characterization approaches. In this paper, a convolution neural network-based deep learning approach (CNN) is reported to infer electrode microstructural properties from the inexpensive, easy to measure cell voltage versus capacity data. The developed framework combines two CNN models to balance the bias and variance of the overall predictions. As an example application, the method was demonstrated against porous electrode theory-generated voltage versus capacity plots. For the graphite|LiMn $$_2$$ 2 O $$_4$$ 4 chemistry, each voltage curve was parameterized as a function of the cathode microstructure tortuosity and area density, delivering CNN predictions of Bruggeman’s exponent and shape factor with 0.97 $$R^2$$ R 2 score within 2 s each, enabling to distinguish between different types of particle morphologies, anisotropies, and particle alignments. The developed neural network model can readily accelerate the processing-properties-performance and degradation characteristics of the existing and emerging LIB chemistries.

25 ENERGY STORAGE↗

PyChargeModel (Oriented Programming Based Electric Vehicle and Electric Vehicle Supply Equipment Charging Model in Python) [SWR-22-39]

The PyChargeModel creates two classes called "ElectricVehicles" and "evse_class", which can be used to create multiple instances of electric vehicles (EVs) and electric vehicle supply equipment (EVSE or charging ports) and simulate charging behavior. These objects can be instantiated with several properties such as battery chemistries, battery pack sizes, cell sizes, charging port power, dc or ac chargers etc. The objects can communicate with each other by calling different methods built within the classes. Through these methods, each EV object can be assigned to an EVSE, charged either using a default protocol or using setpoint values communicated from a site controller via the EVSE object.

Mishra, Partha↗

Identification of dopant site and its effect on electrochemical activity in Mn-doped lithium titanate

Doped metal oxide materials are commonly used for applications in energy storage and conversion, such as batteries and solid oxide fuel cells. The knowledge of the electronic properties of dopants and their local environment is essential for understanding the effects of doping on the electrochemical properties. Using a combination of x-ray absorption near-edge structure spectroscopy (XANES) experiment and theoretical modeling we demonstrate that in the dilute (1 at .%) Mn-doped lithium titanate (Li 4/3 Ti 5/3 O 4 , or LTO) the dopant Mn 2+ ions reside on tetrahedral (8a) sites. First-principles Mn K-edge XANES calculations revealed the spectral signature of the tetrahedrally coordinated Mn as a sharp peak in the middle of the absorption edge rise, caused by the 1s → 4 p transition, and it is important to include the effective electron-core hole Coulomb interaction in order to calculate the intenisty of this peak accurately. Finally, this dopant location can explain the impedance of Li migration through the LTO lattice during the charge-discharge process, and, as a result, the observed remarkable 20% decrease in electrochemical capacity of the 1% Mn-doped LTO compared to pristine LTO.

36 MATERIALS SCIENCE↗