Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Tensile and compressive mechanical behavior of twinned silicon carbide nanowires

Molecular dynamics simulations with the Tersoff potential were used to study the response of twinned SiC nanowires under tensile and compressive strains. The critical strain of the twinned nanowires can be enhanced by twin-stacking faults, and their critical strains are larger than those of perfect nanowires with the same diameters. Under axial tensile strain, the bonds of the nanowires are just stretched before failure. The failure behavior is found to depend on the twin segment thickness and the diameter of the nanowires. An atomic chain is observed for the thin nanowires with small twin segment thickness under tension strain. Under axial compressive strain, the collapse of the twinned SiC nanowires exhibits two differently failure modes, depending on the length and diameter of the nanowires, i.e. shell buckling for short length nanowires and columnar buckling for longer length nanowires.

36 MATERIALS SCIENCE↗

A general panel sizing computer code and its application to composite structural panels

A computer code for obtaining the dimensions of optimum (least mass) stiffened composite structural panels is described. The procedure, which is based on nonlinear mathematical programming and a rigorous buckling analysis, is applicable to general cross sections under general loading conditions causing buckling. A simplified method of accounting for bow-type imperfections is also included. Design studies in the form of structural efficiency charts for axial compression loading are made with the code for blade and hat stiffened panels. The effects on panel mass of imperfections, material strength limitations, and panel stiffness requirements are also examined. Comparisons with previously published experimental data show that accounting for imperfections improves correlation between theory and experiment.

Anderson, M. S.↗

Postbuckling of eccentric open-section stiffened composite panels

A numerical study of the postbuckling behavior of open-section stiffened composite compression panels is presented with emphasis on the effects of an anisotropic attached flange on results, the strain distribution near collapse, and the change of buckle pattern during postbuckling response. Results are obtained for a blade stiffened panel with orthotropic or anisotropic attached flanges from a new verison of STAGS, a general, branched shell, nonlinear computer program. Comparisons between these results indicate the effects of anisotropic flanges on the results. Elastic strain distributions are obtained from STAGS and indications are given about the collapse loads and modes of a particular panel. Change of buckle pattern is studied using STAGS and a special purpose computer program for long plates. Comparisons are made with experimental results.

Stein, Manuel↗

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.

Batdorf, S B↗

An Investigation of Sheet-stiffener Panels Subjected to Compression Loads with Particular Reference to Torsionally Weak Stiffeners

A total of 183 panel specimens of 24ST aluminum alloy with nominal thickness of 0.020, and 0.040 inch with extruded bulb-angle sections of 12 shapes spaced 4 and 5 inches as stiffeners were tested to obtain the buckling stress and the amplitude of the maximum wave when buckled. Bulb angles from 3 to 27 1/2 inches long were tested as pin-end columns. The experimental data are presented as stress-strain and column curves and in tabular form. Some comparisons with theoretical results are presented. Analytical methods are developed that make it possible for the designer to predict with reasonable accuracy the buckling stress and the maximum-wave amplitude of the sheet in stiffened-panel combinations. The scope of the tests was insufficient to formulate general design criteria but the results are presented as a guide for design and an indication of the type of theoretical and experimental work that is needed.

LOADS - COLUMNS↗

Cell prestress. II. Contribution of microtubules

The tensegrity model hypothesizes that cytoskeleton-based microtubules (MTs) carry compression as they balance a portion of cell contractile stress. To test this hypothesis, we used traction force microscopy to measure traction at the interface of adhering human airway smooth muscle cells and a flexible polyacrylamide gel substrate. The prediction is that if MTs balance a portion of contractile stress, then, upon their disruption, the portion of stress balanced by MTs would shift to the substrate, thereby causing an increase in traction. Measurements were done first in maximally activated cells (10 microM histamine) and then again after MTs had been disrupted (1 microM colchicine). We found that after disruption of MTs, traction increased on average by approximately 13%. Because in activated cells colchicine induced neither an increase in intracellular Ca(2+) nor an increase in myosin light chain phosphorylation as shown previously, we concluded that the observed increase in traction was a result of load shift from MTs to the substrate. In addition, energy stored in the flexible substrate was calculated as work done by traction on the deformation of the substrate. This result was then utilized in an energetic analysis. We assumed that cytoskeleton-based MTs are slender elastic rods supported laterally by intermediate filaments and that MTs buckle as the cell contracts. Using the post-buckling equilibrium theory of Euler struts, we found that energy stored during buckling of MTs was quantitatively consistent with the measured increase in substrate energy after disruption of MTs. This is further evidence supporting the idea that MTs are intracellular compression-bearing elements.

Non-NASA Center↗

Evaluation of Superplastic Forming and Weld-brazing for Fabrication of Titanium Compression Panels

The two titanium processing procedures, superplastic forming and weld brazing, are successfully combined to fabricate titanium skin stiffened structural panels. Stiffeners with complex shapes are superplastically formed using simple tooling. These stiffeners are formed to the desired configuration and required no additional sizing or shaping following removal from the mold. The weld brazing process by which the stiffeners are attached to the skins utilize spot welds to maintain alignment and no additional tooling is required for brazing. The superplastic formed/weld brazed panels having complex shaped stiffeners develop up to 60 percent higher buckling strengths than panels with conventional shaped stiffeners. The superplastic forming/weld brazing process is successfully scaled up to fabricate full size panels having multiple stiffeners. The superplastic forming/weld brazing process is also successfully refined to show its potential for fabricating multiple stiffener compression panels employing unique stiffener configurations for improved structural efficiency.

Royster, D. M.↗

Down-bucklng of a corner of a descending plate

A model of the earth's crust is presented as a set of rigid crustal blocks in which the crust is consumed, compressed, or created only at the boundaries of the blocks. As such the trench boundary moves with respect to the colliding plates because of down-buckling at the corner of the descending plate. It is further shown that this mechanism requires plate consumption of the descending plate at a rate faster than the relative plate motion, which in turn causes infilling of the basin behind the arc to compensate for the increased destruction. It is demonstrated that earthquake, heat flow, paleomagnetic, gravity anomaly, and geologic data derived from Japan and the Sea of Japan support the model.

Lowrey, B. E.↗

Postbuckling and failure characteristics of selected flat rectangular graphite-epoxy plates loaded in compression

Results of an experimental study of the postbuckling response and failure characteristics of 16- and 24-ply quasi-isotropic and 24-ply orthotropic flat rectangular graphite-epoxy plates loaded in compression are examined. Some of the specimens had circular drilled holes or were subjected to low-speed impact damage. The ratio of failure load to buckling load was found to be higher for specimens with lower initial buckling strains than for specimens with higher initial buckling strains. Some specimens supported more than five times their initial buckling load before failing. The specimens failed along a nodal line of the buckling mode in an induced shear failure mode. Holes and impact damage had a more adverse effect on the postbuckling strength of specimens with high initial buckling strains than on the strength of specimens with lower initial buckling strains.

Starnes, J. H., Jr.↗

Postbuckling behavior of graphite-epoxy panels

Structurally efficient fuselage panels are often designed to allow buckling to occur at applied loads below ultimate. Interest in applying graphite-epoxy materials to fuselage primary structure led to several studies of the post-buckling behavior of graphite-epoxy structural components. Studies of the postbuckling behavior of flat and curved, unstiffened and stiffened graphite-epoxy panels loaded in compression and shear were summarized. The response and failure characteristics of specimens studied experimentally were described, and analytical and experimental results were compared. The specimens tested in the studies described were fabricated from commercially available 0.005-inch-thick unidirectional graphite-fiber tapes preimpregnated with 350 F cure thermosetting epoxy resins.

Starnes, J. H., Jr.↗

Nonlinear analysis of compressively loaded linked-plate structures

A method is presented for the geometrically nonlinear analysis of the equilibrium behavior of a general class of compressively loaded, prismatic, linked-plate structures. The semi-analytical method accounts for geometric shape imperfections, and allows the use of laminated composite plate properties. Buckling eigenfunctions are used as displacement shape functions, and the associated second-order displacement fields are incorporated. The nonlinear plate equilibrium equations are expressed in terms of the assumed displacement form, and the Galerkin method is used to obtain a set of algebraic equations which are nonlinear in the modal amplitudes and the load parameter. Buckling eigensolutions for the class of structures under consideration can be obtained from the VIPASA computer code; thus, subject to some additional restrictions in loading and plate anisotropy, structural configurations which can be analyzed with regard to buckling response by VIPASA can be analyzed with regard to geometrically nonlinear response using the new method.

Stoll, Frederick↗

Design considerations for compression panels at elevated temperature

The potential of graphite/polyimide is assessed on a graphite/polyimide honeycomb sandwich panels and stiffened panel concepts to develop lightweight panels for use at elevated temperatures. The capability is attained to correctly predict panel buckling behavior and panel strength at elevated temperatures.

Mcwithey, R. R.↗

Buckling analysis of laminated thin shells in a hot environment

Results are presented of parametric studies to assess the effects of various parameters on the buckling behavior of angle-ply, laminated thin shells in a hot environment. These results were obtained by using a three-dimensional finite element analysis. An angle-ply, laminated thin shell with fiber orientation of (theta/-theta)(sub 2) was subjected to compressive mechanical loads. The laminated thin shell had a cylindrical geometry. The laminate contained T300 graphite fibers embedded in an intermediate-modulus, high-strength (IMHS) matrix. The fiber volume fraction was 55 percent and the moisture content was 2 percent. The residual stresses induced into the laminate structure during the curing were taken into account. Parametric studies were performed to examine the effect on the critical buckling load of the following parameters: cylinder length and thickness, internal hydrostatic pressure, different ply thicknesses, different temperature profiles through the thickness of the structure, and different lay up configurations and fiber volume fractions. In conjunction with these parameters the ply orientation was varied from 0 deg to 90 deg. Seven ply angles were examined: 0 deg, 15 deg, 30 deg, 45 deg, 60 deg, 75 deg, and 90 deg. The results show that the ply angle theta and the laminate thickness had significant effects on the critical buckling load. The fiber volume fraction, the fiber orientations, and the internal hydrostatic pressure had important effects on the critical buckling load. The cylinder length had a moderate influence on the buckling load. The thin shell with (theta/-theta)(sub 2) or (theta/-theta)(sub s) angle-ply laminate had better buckling-load performance than the thin shell with (theta)(sub 4) angle-ply laminate. The temperature profiles through the laminate thickness and various laminates with the different ply thicknesses has insignificant effects on the buckling behavior of the thin shells.

Gotsis, Pascal K.↗

The Effective Width of Curved Sheet After Buckling

This report describes experiments made for the purpose of ascertaining the effective width of circularly curved sheet under pure flexural stress. A relation for the effective width of curved sheets is established. Experiments were made with circular cylinders compressed in longitudinal direction. The sheets were rigidly built in at the sides parallel to the axis of the cylinder.

Wenzek, W A↗

Delamination and Buckling Analysis of a Laminated Component in a High-speed Permanent Magnet Motor

High-speed permanent magnet (PM) machines are widely used because of their high-power density and high efficiency. The high rotation speed also inevitably subjects the PMs to high centrifugal load, which might damage them due to their inherent mechanical vulnerability, such as a much lower tensile strength than the compressive strength. To robustly transfer the torque from the magnet to the shaft, the outer diameter of the laminated rotor core is larger than the inner diameter of the rotor frame to ensure tight contact while working at 20,000 rpm. Motor manufacturing requires the shrink-fit method to assemble the rotor frame and rotor core. However, after the shrink-fit assembly, unexpected local delamination and buckling are observed on the rotor core part. Utilizing finite element simulation, we study the internal stress of assembling these two parts at the provided interference. Simulation results indicate the reasons for the delamination and buckling of the rotor core part and provide suggestions for improving the assembly.

Lin, Lianshan↗

Deformation behavior of nanoscale Al–Al 2 Cu eutectics studied by in situ micropillar compression

We report deformation behavior of nanoscale laser processed Al–Al 2 Cu eutectics at room temperature is characterized through in situ micro-pillar compression testing in a scanning transmission microscope. Interlamellar spacing of Al–Al 2 Cu eutectics varies from hundreds of nanometers to 20 nm. Three different sizes of micro-pillars are fabricated in order to study the deformation behaviors of single colony and multiple colonies, corresponding to the single crystal and polycrystal respectively. For single colonies, lamellar orientations parallel, normal or inclined to the loading direction were tested. The main findings are: 1) the plasticity mechanisms strongly depend on loading orientation: buckling and kinking in the parallel-loaded eutectics, planar sliding along Al–Al 2 Cu lamellar interfaces in the incline-loaded eutectics and localized shearing in the normal-loaded eutectics. 2) the incline-loaded eutectics exhibits the lowest compression flow strength, and the normal-loaded eutectics has the highest compression flow strength. 3) with decreasing inter-lamellar spacing, the strength increases and plasticity is uniformly distributed, as opposed to shear localization. Highest compressive plasticity is observed in polycrystalline eutectics with an ensemble of lamellar orientations with ~20 nm average spacing: 17.9% at flow stress of 1.63 GPa, and degenerate, bimodal morphology: 11.1% at flow stress of 1.36 GPa.

36 MATERIALS SCIENCE↗