Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Sensitivity Studies on UNF Cladding Structural Integrity under NCT Loading

This work describes the sensitivity analyses performed on the transportation package used in the NCT initial modeling and simulation demonstration [1]. The initial demonstration predicted the structural integrity of the fuel cladding by integrating models from the fuel rod/grid slot level, the single assembly-level, and the full cask-level. A number of sensitivity analyses were performed on the models at the different levels to determine how sensitive the results were to the parameters that were varied. The results are used to coarsely group the parameters investigated into four categories of sensitivity: No Sensitivity, Low Sensitivity; Moderate Sensitivity, and High Sensitivity. The High Sensitivity analyses are described in detail below. The Moderate, Low and No Sensitivity results are briefly described.

used nuclear fuel, UNF, normal conditions of trans↗

DOE EM Sponsored Research on Long-Term Dry Storage of Aluminum Clad SNF

This PowerPoint presentation describes and discusses DOE EM and INL lead studies on addressing potential technical issues associated with long-term dry storage of aluminum clad spent nuclear fuel. This same presentation was made to the US Nuclear Waste Technical Review Board in Nov 2019.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Irradiation damage and IASCC of printed 316L for use as fuel cladding

Additive manufacturing is an area of increasing interest to the nuclear industry. It offers a number of benefits over traditional manufacturing methods, such as the ability to create complex geometries without the need for welds. In addition to the potential for creating nuclear structural components, additive manufacturing may be used to create novel fuel/cladding designs. However, printed steel behaves differently than traditional wrought material. A number of industries are already studying the effects of the printed microstructures on mechanical properties. For cladding material and some structural nuclear components, however, the nuclear industry must also understand the material response to irradiation. This work examines the irradiation damage and the irradiation assisted stress corrosion cracking behavior of both proton irradiated (1 and 5 dpa) printed 316L steel and wrought 316L steel that were irradiated side by side at the Michigan Ion Beam Laboratory. As orientation with respect to the build direction can affect the mechanical properties of printed metal, specimens were taken from multiple orientations within the printed steel. For the IASCC testing, specimens were strained to 4% in simulated BWR NWC water (288°C, 0.2 µS/cm). TEM, SEM and X-ray microCT were used to examine coupons of the material as well as tensile bars used in the IASCC testing. This paper will show the key findings from this work, namely the IASCC response of printed metal (as compared to wrought), as well as the effects of the printed microstructure (such as the pre-existing voids) on the irradiation damage.

36 MATERIALS SCIENCE↗

Analysis of the absorbed hydrogen in cladding tubes applied in the QUENCH-LOCA tests

A shortened loss of coolant scenario was simulated experimentally at fuel rod bundle scale in the QUENCH-LO test. All pressurized rods burst at temperatures between 790 and 855 deg. C. The hydrogen distribution in the cladding of chosen fuel rod simulators was studied by neutron radiography and tomography. It was shown that the time between burst and quenching as well as the temperatures occurring during this period, and hence the degree of inner oxidation, are important parameters for the hydrogen uptake. No hydrogen uptake was measured for the specimen with 63 s or less between burst and quenching. For longer time intervals, hydrogen enriched bands were formed. These bended bands are oriented non-symmetrically to the tube axis. Micro-structure investigations give hints that the hydrogen keeps in solution in the a-zirconium lattice. The hydrogen enriched bands influence the mechanical properties of the rods, characterized by a higher hardness. Brittle fracture occurs in these bands in the tensile test. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Nuclear analyses of supercritical water cooled reactor with carbon nano-tube cladding

The authors have confirmed the feasibility of the dual layer clad comprised of iron and carbon nano-tube to problems of Super Critical Water Reactor cores. Continuous energy Monte Carlo method was applied. The difference between JENDL-3.3 and ENDF-6 was confirmed. Depletion was carried out. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Improved cladding nano-structured materials with self-repairing capabilities

When designing nuclear reactors or the materials that go into them, one of the key challenges is finding materials that can withstand an outrageously extreme environment. In addition to constant bombardment by radiation, reactor materials may be subjected to extremes in temperature, physical stress, and corrosive conditions. A limitation in fuel burnup is and usage of the nuclear fuel material is related to the structural material radiation damage, that makes the fuel be removed with low-burnup and immobilized in the waste storage pools. The advanced burnup brings cladding material embitterment due to radiation damage effects corroborated with corrosion effects makes the fuel pellet life shorter. The novel nano-clustered structured sintered material may mitigate simultaneously the radiation damage and corrosion effects driving to more robust structural materials that may make the nuclear reactor safer and more reliable. The development of nano-clustered sinter alloys provides new avenues for further examination of the role of grain boundaries and engineered material interfaces in self-healing of radiation-induced defects driving to the design of highly radiation-tolerant materials for the next generation of nuclear energy applications. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Oxidation of SiC cladding under Loss of Coolant Accident (LOCA) conditions in LWRs

An experimental assessment of Silicon Carbide (SiC) cladding oxidation rate in steam under conditions representative of Loss of Coolant Accidents (LOCA) in light water reactors (LWRs) was conducted. SiC oxidation tests were performed with monolithic alpha phase tubular samples in a vertical quartz tube at a steam temperature of 1140 deg. C and steam velocity range of 1 to 10 m/sec, at atmospheric pressure. Linear weight loss of SiC samples due to boundary layer controlled reaction of silica scale (SiO{sub 2} volatilization) was experimentally observed. The weight loss rate increased with increasing steam flow rate. Over the range of test conditions, SiC oxidation rates were shown to be about 3 orders of magnitude lower than the oxidation rates of zircaloy 4. A SiC volatilization correlation for developing laminar flow in a vertical channel is formulated. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Status of the MeLoDIE experiment, an advanced device for the study of the irradiation creep of LWR cladding with full online capabilities

As a prototype of future instrumented material experiments in the Jules Horowitz Reactor (JHR), the MELODIE project was launched in 2009 by the CEA in collaboration with VTT. Being designed as a biaxial creep experiment with online capability, MELODIE is able to apply an online-controlled biaxial loading on a LWR clad sample up to 120 MPa and to perform an online measurement of its biaxial deformation. An important experimental challenge was to perform reliably accurate measurements under the high nuclear heat load of in-core locations while keeping within their tight space. For that purpose, specific sensors were co-designed with and built by IFE Halden. Manufacturing of the MELODIE components was completed one year ago. The complexity of its in-pile section and of the pressurization system requested a step-by-step tuning of the setup. The toughest part of this process dealt with the Diameter gauge which required a partial redesign to take into account unexpected and unwanted electromagnetic interactions with the hosting device. Final cold performance tests of the on-board instrumentation will be presented. The MELODIE device is now ready and irradiation should start in OSIRIS reactor this spring. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Corrosion test of LWR cladding tubes in high temperature seawater

In the case of cooling system failure in spent fuel pools (SFP) due to station black out and/or loss of coolant accidents, a pool water level must be kept high enough to avoid overheat of spent fuels. Seawater is one of the candidate coolant materials in such emergencies. In the present work, we have studied the corrosion behavior of zirconium alloys in seawater. Tube samples of Zircaloy-2 and -4 claddings were immersed in artificial seawater (3, 10 and 20 wt.%) at high temperature (80 - 85 Celsius degrees). Boric acid was added to the seawater at a corrosion test of Zircaloy-4. Two types of specimens were prepared according to the simulation of circumferential tensile stress. One was a plugged tube specimen, which was pressurized to around fuel rod pressure in a spent fuel pool by argon gas. Another specimen was of C-ring shape, where large circumferential tensile stress was partially induced at the surface. A notch was longitudinally grooved to increase the local tensile stress on some of the C-ring specimens. The specimen surface was observed by a scanning electron microscopy (SEM) after the corrosion test. After the 200 day long corrosion test for the plugged tube specimens without boric acid, Mg(OH){sub 2} deposits were observed on the surface of Zircaloy-2 and -4 specimens whereas Mg(OH){sub 2} was not observed with boric acid because of probably a lower pH. Neither pitting corrosion nor stress corrosion cracking (SCC) was observed on the surface of all plugged tube specimens. Only in the C-ring specimens in 20 wt.% seawater without boric acid and in 3 and 10 wt.% seawater with boric acid, small cracks were observed at the notch. The results of the present work show that Zircaloy-2 and -4 have a high tolerance towards corrosion and SCC in high temperature seawater.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Advanced synthesis for enhanced accident tolerant of LWR cladding materials

Advanced materials synthesis is utilized at Argonne National Laboratory (ANL) with the intended goal of improving performance of light water reactor (LWR) claddings under normal operation and accident conditions. The advanced synthesis utilizes atomic layer deposition (ALD) techniques to infiltrate SiC wires wrapped around ZIRLO tubes with SiC deposits, to form a SiC-SiC composite on the ZIRLO tubes. This paper reports on the effort to deposit SiC using ALD. The deposition was successful in infiltrating deep into the wires structure, reaching the surface of the ZIRLO tubes, as indicated through different characterization techniques. Because of the slow deposition rate of SiC, only a limited amount of SiC was deposited (a few hundreds of nm of SiC thick layers). This was followed by a few micrometers of ALD deposition of zircon (ZrSiO{sub 4}.) on top of the SiC deposition. The additional deposition was adequate to hold the wires together around the tube. Work is ongoing to increase the SiC ALD deposition rate, and infiltrate the larger pores within the wires with other SiC deposition methods such as low temperature chemical vapor deposition (CVD). (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of FeCrAl-ODS steels for ATF cladding

As an enhanced accident tolerant fuel (ATF) for LWR at severe accident condition, FeCrAl-ODS ferritic steels have been developed, and their applicability is being studied under the Japanese MEXT program. Alloying design of FeCrAl-ODS ferritic steels has been conducted, focusing on effect of mutual interaction of Cr-Al on oxidation resistance and α'-embrittlement. Effects of co-addition of Zr and excessive oxygen have also been studied to improve high-temperature strength. The ring tensile test of the manufactured claddings showed that tensile strength increases by Zr-addition and Zr-added FeCrAl-ODS steels have the highest strength among the existed steels at entire temperature range from room temperature up to 1000 Celsius degrees. Although Zr-addition sometimes leads to growth of alumina scale by rapid inward diffusion of oxygen through zirconia inside alumina, oxidation rate of Zr-added FeCrAl-ODS steels was successfully reduced to the level of Zr-free specimen by controlling oxygen content to form Y{sub 2}Zr{sub 2}O{sub 7} inside ODS steel matrix. This finding makes possible to improve not only high-temperature strength but also steam oxidation resistance in the Zr-added FeCrAl-ODS steels. (authors)

36 MATERIALS SCIENCE↗

All SiC/SiC cladding irradiation in LWR environments

The Muroran Institute of Technology has been in charge of developing SiC/SiC claddings by the DEMO-NITE method, and to evaluate stability in reactor water environment, in high temperature steam environment and in neutron exposure environment. Those issues have been studied during five years and carried out in 3 experiments (Scarlet-1, Scarlet-2 and Inspire-1) irradiated in the Halden Boiling Water Reactor (HBWR) in Norway. The main conclusions follow. The corrosion of SiC/SiC is accelerated by the neutron irradiation. The corrosion of SiC/SiC significantly depends on the condition of water chemistry, and the corrosion of SiC/SiC is drastically decreased under hydrogen water chemistry. Under boiling water condition, the corrosion rate of SiC/SiC is slightly increased. The significant degradation at a joint was confirmed by the galvanic corrosion caused by the joining of dissimilar materials. As expected, there is no degradation of full SiC/SiC segment prepared by diffusion bonding. Microstructural change of CVD-SiC coat on SiC/SiC tubes was not observed. The effectiveness of CVD (Chemical Vapor Deposition) SiC coat as environmental barrier coating is confirmed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Characterization of SiC-SiC accident tolerant fuel cladding after stress application

In this work, SiC-SiC tubes with representative LWR (water cooled reactor) cladding dimensions were subjected to cycles of out-of-pile thermal stress followed by quenching. Samples were held at elevated temperatures and dropped into a water bath to replicate the high thermal stresses generated during reflooding. The samples were then characterized to measure changes in strength, permeability, and structure. Results were evaluated both for quenching into room temperature and boiling water. The results show that SiC-SiC composite tubes quenched from 1000 Celsius degrees in air into a boiling water bath exhibited no increase in He leak rate through the cylinder wall up to a pressure difference of 34.5 kPa compared to the as-fabricated state. SiC-SiC composite tubes quenched from 300-400 C. degrees into room temperature water showed an increase in He leak rate compared to the as-fabricated state. We attribute this to the more severe thermal gradient generated through the wall thickness due to higher heat flux characteristic of nucleate boiling compared to film boiling. A persistent vapor film forms around the samples quenched into boiling water, whereas no vapor film forms for the samples quenched into room temperature water. Another important result is that not loss in strength was noted compared to unquenched samples and that the stresses generated by the quenching were not enough to cause fiber fracture.

36 MATERIALS SCIENCE↗

Corrosion resistant coatings for zirconium-alloy cladding with improved accident tolerance

The Westinghouse-led accident tolerant fuel (ATF) program is evaluating Accident Tolerant Fuel (ATF) coatings of MAX phase (Ti{sub 2}AlC) and multi-layer Ti{sub x}Al{sub 1-x}N/TiN to enhance the oxidation resistance of zirconium alloy fuel cladding in both normal operation and beyond design-based conditions of light water reactors. A variety of coating technologies have been applied to deposit these coating materials onto Zircaloy-4 or Zirlo sheets and tubes, including cold spray and cathodic arc-physical vapor deposition (CA-PVD). Neutronic analysis using the elemental compositions of the coating materials showed that the coating thicknesses should be less than 30 μm for most coating materials to avoid non-negligible economic penalty. The coated samples were autoclave tested in water at 360 Celsius degrees and 150 bar or in steam at 427 Celsius and 103 bar for corrosion resistance evaluation. The initial Ti{sub 2}AlC coating made by using large particle size MAX phase powder and cold spray deposition did not provide the desired corrosion resistance due to un-optimized microstructure and porosity. Subsequent optimization including reduction in particle size and tuning of cold spray deposition parameters resulted in denser coatings less than 30 microns in thickness. Optimization of process conditions resulted in reduced oxidation kinetics and showed that the coating acts as an effective barrier to prevent the zirconium substrate from oxidizing in accident condition temperatures. High purity Ti{sub 2}AlC powder is needed to further improve oxidation resistance of the Ti{sub 2}AlC coating. The oxidation resistance of pure monolithic MAX phase compound was also found to be remarkable, and the weight gain was only 1.85 mg/cm{sup 2} for 96 hours exposure in 1200 C. degrees steam, which is consistent with the literature. The corrosion resistance of the TiAlN/TiN multilayer coating was excellent. The weight gain was negligible and no oxidation was observed on the surface of zirconium-alloy at the coating-substrate interface. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pile Fuel Cladding Silo Deflector Plate Removal Project Using Long Reach Tooling and Suspended Abrasive Water Jet Cutting System - 17541

The Pile Fuel Cladding Silo (PFCS) at the Sellafield decommissioning, reprocessing and nuclear waste management facility in the UK was constructed in the late 1940-s and used for the storage of Intermediate Level Waste (ILW) arising from the Windscale Piles, Calderhall and Chapelcross Reactors until the 1960's. The PFCS is 21 metres high and comprises 6 identical tall compartments with the waste added to the silo via a charge-hole at the top of each compartment; each compartment is split by a central dividing wall that runs from the base of the silo to a few metres below the underside of the silo roof. A deflector plate assembly (DPA) supported on two horizontal beams is located between the top of the dividing wall and the roof and allowed the waste to spread as it fell into the silo and prevent excessive mounding. Sellafield Ltd is currently engaged in an overall programme of works to remove the waste for storage within modern ILW containers. Prior to the commencement of these works the Deflector Plate Assemblies (DPA) and beam structures within the silos are required to be removed to allow access for the waste retrievals equipment through the side of the silo at the point where the DPAs are situated. James Fisher Nuclear (JFN) and Sellafield Ltd have developed a system using suspended water jet cutting equipment combined with custom long reach tooling, installed through penetrations made in the side of the silo, to enable the remote size reduction of the DPA and beams within each compartment. The use of a low pressure suspended water jet cutting system has enabled a single water/abrasive hose to be routed down a tool deployment pole and allowed long hose lengths up to 80 m from pump to nozzle enabling siting of equipment on a congested and difficult access site. The use of lightweight, yet high strength, carbon fibre poles within the tools has enabled the deployment of tool end effectors at distances of up to 6.5 m from the compartment walls using a relatively small 60 mm diameter pole. This maximised articulation of the pole within the 300 mm wall penetrations to reach all areas of the DPA. Capability of the operators to install the tooling and size reduce DPA and beam assemblies have been demonstrated through the training on a Full Scale Test Rig (FSTR). The FSTR was integral to the development of the equipment and techniques and to providing assurance to the client that the project was technically achievable given the tight building restraints and safety issues. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Electrorefining of Zircaloy-4 in LiCl-KCl to Decontaminate Irradiated Cladding - 16238

Electrorefining on unirradiated Zircaloy-4 specimen in LiCl-KCl was performed by managing the anode potential to identify whether high purity zirconium can be recovered in metallic form by electrorefining. Four different concentrations of ZrCl{sub 4} (0.1, 0.5, 1.0 and 2.0 wt%) were tested. Results indicate that high purity metallic zirconium was recovered at low concentration of ZrCl{sub 4} but ZrCl could be recovered at high concentration. The electrorefining experiments were simulated by a three-dimensional computational electrorefining model. Several physical properties were tested, and a set of physical properties was determined in the condition where chemical forms of cathode deposits estimated by the computational model accorded with the experimental results. Using those properties, co-deposition of zirconium and uranium was simulated in the geometry of a preliminary designed electro-refiner for irradiated Zircaloy claddings. Operating conditions that can lead to the formation of zirconium metal without ZrCl and uranium were calculated. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Advanced Characterization of Fuel Pellet and Cladding from the HB Robinson NPP

In order to predict the behavior and response of materials to extreme environments of a nuclear reactor, comprehensive models have been developed over the past several decades. These models are typically validated against carefully designed single or double variable experiments which may be systematically altered in order build up a model of behavior under the conditions being examined. In reality, this does not necessarily compare well with the real application situations whereby the behavior of the material under irradiation is determined by multiple variables changing simultaneously e.g. temperature, irradiation flux and fluence, and pressure. This is particularly so when considering the highly dynamic environment of a fuel assembly within a nuclear power plant (NPP) core. This work aims to provide near-atomic resolution microstructural and chemical data of a fuel/clad specimen that has been used in service within a commercial NPP. Atom probe tomography and S/TEM characterization of the cladding showed the presence of small scale clusters containing Fe and Cr, along with segregation of these minor solutes to dislocations. SEM examination of the fuel pellet showed relatively large fission gas bubbles that had burst due to the metallographic polishing process to prepare the sample for examination. SEM-EDX mapping revealed the presence of Xr bubbles located beneath the surface that still retained their Xe concentration. Metallic precipitates were also observed. S/TEM-EDX of the fuel material also revealed the presence of small metallic precipitates. In addition, small Xe bubbles were also found to be present in the material, lying along grain boundaries only. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synchrotron Characterization of the Oxidation of Advanced Steel Cladding Alloys

Advanced steel alloys are proposed as nuclear fuel claddings due to their high corrosion resistance under extreme conditions of pressure and temperature. APMT is an iron based alloy (Fe-22wt.%Cr-5.8wt.%Al) and Alloy 33 is a mixture of iron, chromium, and nickel (32wt.%Fe-33wt.%Cr-31wt.%Ni). This paper focuses on studying the corrosion mechanisms for these alloys under exposure to superheated steam at 800 deg. C and 1000 deg. C using the synchrotron based X-ray diffraction (XRD) and Hard X-ray photoelectron spectroscopy (HAXPES) techniques. HAXPES data was collected using 4 keV X-rays with a 1x1 mm spot size at X24A beamline. Specimens were mounted on the sample holder. The specimens were tilted 5 degrees relative to the beam and the estimated probe depth (for this fixed energy) is 63 A. The X-ray wavelength for XRD studies at X14A beamline is 0.7792 A with a beam size of of 2 x 0.2 mm{sup 2}. Specimens were exposed to steam environment at 800 and 1000 deg. C for 8, 24, and 48 hours. For Alloy 33; a layer of mixed Cr{sub 2}O{sub 3} and FeCr{sub 2}O{sub 4} oxides is formed after exposure to steam. Specimen tilting indicated that Cr{sub 2}O{sub 3} is formed near the metal/oxide interface and FeCr{sub 2}O{sub 4} was formed on the oxide surface. The oxide peak intensities increased with an increase in steam temperature. The specimen oxidized at 1000 deg. C had well-developed oxide peaks compared to the specimen oxidized at 800 deg. C. For APMT; a layer of mixed α-Al{sub 2}O{sub 3} and monoclinic θ-Al{sub 2}O{sub 3} oxides is formed on the outer surface. The peak intensities of the monoclinic θ-Al{sub 2}O{sub 3} phase, decreases relative to the peaks from the Al{sub 2}O{sub 3} phase with increasing tilt angle. This indicates that the surface is dominated by the θ-Al{sub 2}O{sub 3}. After exposure to steam at 800 deg. C, oxidation of Alloy 33 results in the formation of Cr{sub 2}O{sub 3} oxide with time and absence of both metallic and substoichiometric phases is observed. No nickel peaks are seen on the surface after oxidation at 800 deg. C, however Fe(II) peak is noticed after 8 and 24 hours of steam exposure, which then disappears after 48 hours. This presence of FeCr{sub 2}O{sub 4} oxide phase is observed after 8 and 24 hours. After exposure to steam at 1000 deg. C, the Cr{sub 2}p{sub 3/2} doublet persists at all exposure times, indicating the presence of the FeCr{sub 2}O{sub 4} oxide. Nickel peak is found on the surface at all exposure times and is attributed to the presence of Ni(OH){sub 2} phase. This may be due to increased diffusion of Ni through chromic oxide scale at higher temperature as compared to 800 deg. C. This nickel reacts with steam at 1000 deg. C to form Ni hydroxide at the surface. For APMT, after exposure to steam at 800 and 1000 deg. C, no Al and Cr metal peaks are seen. Growth of oxide layer is seen with increase in exposure time. The oxide structure contains mainly Al{sub 2}O{sub 3} oxide with the addition of mixed oxide (Al{sub x}Cr{sub 1-x}){sub 2}O{sub 3}. These results demonstrate that Cr diffuses into the alumina layer. (authors)

36 MATERIALS SCIENCE↗