Search NASA⌕ Search

SEARCH · Search NASA

Results for “Configuration Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Boundary-Layer-Ingesting Inlet Flow Control

An experimental study was conducted to provide the first demonstration of an active flow control system for a flush-mounted inlet with significant boundary-layer-ingestion in transonic flow conditions. The effectiveness of the flow control in reducing the circumferential distortion at the engine fan-face location was assessed using a 2.5%-scale model of a boundary-layer-ingesting offset diffusing inlet. The inlet was flush mounted to the tunnel wall and ingested a large boundary layer with a boundary-layer-to-inlet height ratio of 35%. Different jet distribution patterns and jet mass flow rates were used in the inlet to control distortion. A vane configuration was also tested. Finally a hybrid vane/jet configuration was tested leveraging strengths of both types of devices. Measurements were made of the onset boundary layer, the duct surface static pressures, and the mass flow rates through the duct and the flow control actuators. The distortion and pressure recovery were measured at the aerodynamic interface plane. The data show that control jets and vanes reduce circumferential distortion to acceptable levels. The point-design vane configuration produced higher distortion levels at off-design settings. The hybrid vane/jet flow control configuration reduced the off-design distortion levels to acceptable ones and used less than 0.5% of the inlet mass flow to supply the jets.

Owens, Lewis R.↗

Attitude control/momentum management of the Space Station Freedom for large angle torque-equilibrium-attitude configurations

An attitude-control and momentum-management (ACMM) system for the Space Station in a large-angle torque-equilibrium-attitude (TEA) configuration is developed analytically and demonstrated by means of numerical simulations. The equations of motion for a rigid-body Space Station model are outlined; linearized equations for an arbitrary TEA (resulting from misalignment of control and body axes) are derived; the general requirements for an ACMM are summarized; and a pole-placement linear-quadratic regulator solution based on scheduled gains is proposed. Results are presented in graphs for (1) simulations based on configuration MB3 (showing the importance of accounting for the cross-inertia terms in the TEA estimate) and (2) simulations of a stepwise change from configuration MB3 to the 'assembly complete' stage over 130 orbits (indicating that the present ACCM scheme maintains sufficient control over slowly varying Space Station dynamics).

Parlos, Alexander G.↗

Redundant Control for Air-Circulation Valves

Four computers that control airflow to "X-wing" helicopter rotor arranged in redundant configuration. Ensures circulation control of rotor continues to function even if two of computers fail. Rotor uses 48 valve actuators regulating distribution and quantity of air flowing from leading and trailing edges.

Johnson, R., Jr.↗

Model flight tests of a spin-resistant trainer configuration

Powered, radio-controlled flight tests were conducted on a 1/4-scale model of a spin-resistant trainer configuration to determine the stall departure and spin resistance characteristics provided by an outboard wing leading-edge droop modification. The model was instrumented to provide quantitative as well as qualitative information on flight characteristics. Flight test results indicated that the unmodified configuration (wing leading-edge droop off) exhibited an abrupt, uncontrollable roll departure at the stall. With the outboard wing leading-edge droop installed, the modified configuration exhibited flight characteristics that were resistant to stall departure and spin entry. The stall departure and spin resistance characteristics of the modified configuration were demonstrated in flight maneuvers that included idle-power stalls, full-power stalls, sideslip stalls, and accelerated stalls.

Yip, Long P.↗

Low-speed aerodynamic characteristics of a highly swept arrow wing configuration with several deflected leading edge concepts

The effectiveness of leading edge concepts for minimizing or controlling leading edge flow separation was studied. Emphasis was placed on low speed performance, stability, and control characteristics of configurations with highly swept wings. Simple deflection of the leading edge, a variable camber leading edge system, and a leading edge vortex flow system were among the concepts studied. The data are presented without analysis.

Gentry, G. L., Jr.↗

Aerodynamic Shape Optimization of Complex Aircraft Configurations via an Adjoint Formulation

This work describes the implementation of optimization techniques based on control theory for complex aircraft configurations. Here control theory is employed to derive the adjoint differential equations, the solution of which allows for a drastic reduction in computational costs over previous design methods (13, 12, 43, 38). In our earlier studies (19, 20, 22, 23, 39, 25, 40, 41, 42) it was shown that this method could be used to devise effective optimization procedures for airfoils, wings and wing-bodies subject to either analytic or arbitrary meshes. Design formulations for both potential flows and flows governed by the Euler equations have been demonstrated, showing that such methods can be devised for various governing equations (39, 25). In our most recent works (40, 42) the method was extended to treat wing-body configurations with a large number of mesh points, verifying that significant computational savings can be gained for practical design problems. In this paper the method is extended for the Euler equations to treat complete aircraft configurations via a new multiblock implementation. New elements include a multiblock-multigrid flow solver, a multiblock-multigrid adjoint solver, and a multiblock mesh perturbation scheme. Two design examples are presented in which the new method is used for the wing redesign of a transonic business jet.

Reuther, James↗

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles ( δ a ) to increase lift-to-drag ratio (R/J). Improvements in low speed R/J can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to δ a = 16° relative to the nominal configuration, δ a = 7.5°. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D . Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

High-Lift Common Research Model↗

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles to increase lift-to-drag ratio (L/D). Improvements in low speed L/D can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to an aileron deflected at 16° relative to the nominal configuration of 7.5° deflection. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D. Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

CRM-HL↗

Flight evaluation of configuration management system concepts during transition to the landing approach for a powered-lift STOL aircraft

Flight experiments were conducted to evaluate two control concepts for configuration management during the transition to landing approach for a powered-lift STOL aircraft. NASA Ames' augmentor wing research aircraft was used in the program. Transitions from nominal level-flight configurations at terminal area pattern speeds were conducted along straight and curved descending flightpaths. Stabilization and command augmentation for attitude and airspeed control were used in conjunction with a three-cue flight director that presented commands for pitch, roll, and throttle controls. A prototype microwave system provided landing guidance. Results of these flight experiments indicate that these configuration management concepts permit the successful performance of transitions and approaches along curved paths by powered-lift STOL aircraft. Flight director guidance was essential to accomplish the task.

Franklin, J. A.↗

Aerodynamic static stability and control effectiveness of a parametric shuttle launch configuration

Experimental aerodynamic investigations were conducted in the NASA/MSFC 14-inch Trisonic Wind Tunnel on a 0.004-scale model of the NR ATP baseline Shuttle launch configuration. The test model consisted of the NR ATP baseline orbiter, external tank, and SRB's with nozzles. Six component aerodynamic force and moment data were recorded over an angle of attack range from minus 10 deg to 10 deg at zero degrees sideslip and angle of sideslip range of minus 10 deg to 10 deg at zero angle of attack for a Mach range of 0.6 to 4.96. Rudder flare was constant at 10 deg during the entire test. The purpose of the test was to define the performance, stability, and control characteristics of the launch configuration as well as to investigate the buildup effect of two geometrical parameters.

Ramsey, P. E.↗

Predicting Airport Runway Configurations for Decision-Support Using Supervised Learning

One of the most challenging tasks for air traffic controllers is runway configuration management (RCM). It deals with the optimal selection of runways to operate on (for arrivals and departures) based on traffic, surface wind speed, wind direction, other environmental variables, noise constraints, and several other airport-specific factors. It affects the efficiency of the National Airspace System (NAS) and both surface and airspace operations can benefit from better understanding future runway configurations. In this paper, we present a comprehensive implementation of predictive models for runway configuration estimation from large volumes of historical data. Specifically, operational data from two full years (2018 and 2019) is collected, analyzed, and fused together to build the data product used in this work. The data set differs from prior work in the field in terms of its scope, resolution, and variety of factors collected and considered. Meteorological data is collected from two different sources – current weather conditions from METAR (Meteorological Terminal Aviation Routine Weather Report) and forecast weather conditions from Localized Aviation MOS Program (LAMP). Operational data from the Federal Aviation Administration (FAA) Aviation System Performance Metrics (ASPM) related to scheduled and actual number of arrivals and departures, average taxi times, etc. are collected. NASA’s Sherlock Data Warehouse is used to identify critical information such as go-arounds, and other events that might impact RCM decision-making. All data is collected and aggregated over 15-minute intervals throughout the two years. This provides a resolution like the timescales that might be necessary for runway configuration management decision-making. A variety of supervised learning algorithms are tested including Support Vector Machine, Random Forest, Gradient Boosting, etc. including tuning of the model hyperparameters. The modeling process is applied and presented on two representative U.S. airports – Charlotte Douglas International Airport (KCLT) and Denver International Airport (KDEN). The two airports present different levels of complexity in terms of the total number of configurations used and provide a balanced perspective on the generalizability of the developed approach to other airports in the NAS. Initial results are promising (F1 score of 0.91 at KCLT and 0.83 at KDEN) for data in the test set. The final paper will contain a comprehensive comparison between different models and model building strategies as well as further refined results. Most important predictors for each airport will be identified along with a discussion and recommendations on adapting the framework to other scenarios.

Tejas G Puranik↗

Predicting Airport Runway Configurations for Decision-Support Using Supervised Learning

One of the most challenging tasks for air traffic controllers is runway configuration management (RCM). It deals with the optimal selection of runways to operate on (for arrivals and departures) based on current and forecast of traffic, surface wind speed, wind direction, other environmental variables, noise constraints, and several other airport-specific factors. In this paper, a methodology using supervised learning is developed to build a predictive model for RCM decision-support from large volumes of historical data. Data from two full years (2018 and 2019) related to current and forecast weather, demand/capacity, etc. is collected, analyzed, and fused together. A variety of supervised learning algorithms are tested for predicting runway configuration and hyperparameter tuning is carried out to select the best performing model. The validation process involves two airports of low (Charlotte Douglas International Airport, CLT) and high (Denver International Airport, DEN) complexity of configuration decision-making. The results show significant promise for the two airports with test accuracy of 93% (CLT) and 73% (DEN). The methodology is scalable and generalizable to other airports across the U.S. National Airspace System.

air traffic management↗

Predicting Airport Runway Configuration for Decision-Support Using Supervised Learning

One of the most challenging tasks for air traffic controllers is runway configuration management (RCM). It deals with the optimal selection of runways to operate on (for arrivals and departures) based on current and forecast of traffic, surface wind speed, wind direction, other environmental variables, noise constraints, and several other airport-specific factors. In this paper, a methodology using supervised learning is developed to build a predictive model for RCM decision-support from large volumes of historical data. Data from two full years (2018 and 2019) related to current and forecast weather, demand/capacity, etc. is collected, analyzed, and fused together. A variety of supervised learning algorithms are tested for predicting runway configuration and hyperparameter tuning is carried out to select the best performing model. The validation process involves two airports of low (Charlotte Douglas International Airport, CLT) and high (Denver International Airport, DEN) complexity of configuration decision-making. The results show significant promise for the two airports with test accuracy of 93% (CLT) and 73% (DEN). The methodology is scalable and generalizable to other airports across the U.S. National Airspace System.

air traffic management↗

Effect of ELEVON gap configurations on the longitudinal stability and control effectiveness of the 43-0 space shuttle orbiter (OA118)

Experimental aerodynamic investigations were conducted on a stingmounted 0.0405-scale representation of the 140A/B space shuttle orbiter in a 7.75 by 11-Foot low speed wind tunnel from April 24 to April 26, 1974. Differential inboard/outboard elevon panel deflections with the 6-inch gap were investigated to determine outboard panel aileron effectiveness. The elevons were deflected from +20 degrees to -40 degrees in various combinations. Aerodynamic force and moment data for the orbiter were measured in the body axis system by an internally mounted, six-component strain gage balance. The model was sting mounted with the center of rotation located at F.S. 60.172. The angle of attack range was from -10 degrees to +24 degrees.

Hughes, T.↗

A steering law for a roof-type configuration for a single-gimbal control moment gyro system

Single-Gimbal Control Moment Gyro (SGCMG) systems have been investigated for attitude control of the Large Space Telescope (LST) and the High Energy Astronomy Observatory (HEAO). However, various proposed steering laws for the SGCMG systems thus far have some defects because of singular states of the system. In this report, a steering law for a roof-type SGCMG system is proposed which is based on a new momentum distribution scheme that makes all the singular states unstable. This momentum distribution scheme is formulated by a treatment of the system as a sampled-data system. From analytical considerations, it is shown that this steering law gives control performance which is satisfactory for practical applications. Results of the preliminary computer simulation entirely support this premise.

Yoshikawa, T.↗

Wind tunnel tests of the dynamic characteristics of the fluidic rudder

The fourth phase is given of a continuing program to develop the means to stabilize and control aircraft without moving parts or a separate source of power. Previous phases have demonstrated the feasibility of (1) generating adequate control forces on a standard airfoil, (2) controlling those forces with a fluidic amplifier and (3) cascading non-vented fluidic amplifiers operating on ram air supply pressure. The foremost objectives of the fourth phase covered under Part I of this report were to demonstrate a complete force-control system in a wind tunnel environment and to measure its static and dynamic control characteristics. Secondary objectives, covered under Part II, were to evaluate alternate configurations for lift control. The results demonstrate an overall response time of 150 msec, confirming this technology as a viable means for implementing low-cost reliable flight control systems.

Belsterling, C. A.↗