Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electron Heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Required toroidal confinement for fusion and omnigeneity

Deuterium–tritium (DT) burning requires a long energy confinement times compared to collision times, so the particle distribution functions must approximate local Maxwellians. Non-equilibrium thermodynamics is applicable, which gives relations among transport, entropy production, the collision frequency, and the deviation from a Maxwellian. The distribution functions are given by the Fokker–Planck equation, which is an advection–diffusion equation. A large hyperbolic operator, the Vlasov operator with the particle trajectories as its characteristics, equals a small diffusive operator, the collision operator. The collisionless particle trajectories would be chaotic in stellarators without careful optimization. This would lead to rapid entropy production and transport—far beyond what is consistent with a self-sustaining DT burn. Omnigeneity is the weakest general condition that is consistent with a sufficiently small entropy production associated with the thermal particle trajectories. Omnigeneity requires that the contours of constant magnetic field strength be unbounded in at least one of the two angular coordinates in magnetic surfaces and that there be a symmetry in the field-strength wells along the field lines. Even in omnigenous plasmas, fluctuations due to microturbulence can produce chaotic particle trajectories and the gyro-Bohm transport is seen in many stellarator and tokamak experiments. The higher the plasma temperature above 10 keV, the smaller the transport must be compared to gyro-Bohm for a self-sustaining DT burn. The hot alphas of DT fusion heat the electrons. When the ion–electron equilibration time is long compared to the ion energy confinement time, a self-sustaining DT burn is not possible, which sets a limit on the electron temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Electrostatic turbulence in EAST plasmas with internal transport barrier

Based on first-principles nonlinear gyrokinetic simulations, the electrostatic turbulence properties in the internal transport barrier (ITB) region of an Experimental Advanced Superconducting Tokamak discharge (#93890) are investigated. Specifically, ITBs with steep density and temperature gradients are located in the weakly negative magnetic shear region at the plasma center. In the linear stage, the growth rate and frequency of the ion temperature gradient (ITG) mode increase significantly due to resonant excitation by trapped electrons. That is, the resonance between trapped electrons and the ITG becomes strong due to the precession drift reversal of trapped electrons by the negative magnetic shear and Shafranov shift. Meanwhile, the trapped electron mode is stable in the ITB region due to only a very small fraction of electrons precessing in the direction of the electron diamagnetic drift. Nonlinear simulations show that, after considering the non-adiabatic effect of trapped electrons, the heat conductivity of ions and the turbulence intensity increase by at least a factor of 7 compared with the results only considering the adiabatic effect of electrons. The zonal charge density of trapped electrons can partially cancel that of ions, which weakens the intensity of the zonal flow, and consequently reduces the zonal flow regulation and enhances the turbulent transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Energy transport analysis of NSTX plasmas with the TGLF turbulent and NEO neoclassical transport models

This work presents a study of plasma transport at low aspect ratio on the National Spherical Torus Experiment tokamak, where the turbulent and neoclassical energy fluxes calculated by the quasilinear Trapped Gyro Landau Fluid (TGLF) model and the multi species drift-kinetic Neoclassical solver (NEO) are validated against experimental data. The turbulent energy transport of two plasma discharges, one in the L-mode confinement regime and another in the H-mode regime, is dominated by electrostatic drift-wave instabilities, while the ion heat transport has a significant neoclassical contribution. The data analysis workflow is described in detail to understand how the variations of mapping and fitting of experimental data affect the power balance solution and subsequent flux-matching plasma profile predictions with the TGYRO solver. On average, the predicted plasma profiles are consistent with experimental data. However, the solutions are sensitive to various input parameters, including boundary conditions, and the electron-ion coupling. Linear gyrokinetic stability analysis demonstrates close agreement of the real frequencies of unstable modes between TGLF and CGYRO gyrokinetic simulations, but higher growth rates are predicted by TGLF, especially for the H-mode case. Estimates of the low-k modes' contributions to the total flux are consistent with linear stability analysis and the E × B suppression of turbulence in TGLF simulations with the SAT1 saturation model, while the SAT2 saturation model over-predicts the low-k modes' contribution in the H-mode case. Moreover, the results with SAT1 model are consistent with power balance analysis, which indicates only neoclassical ion energy fluxes inside ρ < 0.4 in the L-mode case and $\rho \unicode{x2A7D} 0.7$ in the H-mode case. The presence of multi-scale turbulence and ion-scale driven zonal flow mixing effects are also observed in TGLF scans of the electron turbulent heat flux over a range of temperature gradients and the electron-ion temperature ratio, which could explain the strong model sensitivity to variations of input parameters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1992

Electron distributions upstream of the Comet Halley bow shock - Evidence for adiabatic heating

Three-dimensional plasma electron (22 eV to 30 keV) observations upstream of Comet Halley bow shock, obtained by the RPA-1 COPERNIC (Reme Plasma Analyzer - Complete Positive Ion, Electron and Ram Negative Ion Measurements near Comet Halley) experiment on the Giotto spacecraft are reported. Besides electron distributions typical of the undisturbed solar wind and backstreaming electrons observed when the magnetic field line intersects the cometary bow shock, a new type of distribution, characterized by enhanced low energy (less than 100 eV) flux which peaks at 90-deg pitch angles is found. These are most prominent when the spacecraft is on field lines which pass close to but are not connected to the bow shock. The 90-deg pitch angle electrons appear to have been adiabatically heated by the increase in the magnetic field strength resulting from the compression of the upstream solar wind plasma by the cometary mass loading. A model calculation of this effect which agrees qualitatively with the observed 90-deg flux enhancements is presented.

Larson, D. E.↗
NASA NTRS1974

Electrical heating tests of uranium dioxide external fuel configuration at emitter temperature of 1900 K

Testing of two fuel clad specimens for thermionic reactor application is described. The annular UO2 fuel was clad on both sides with tungsten; heat rejection was radially inward. The tests were intended to study inner clad stability, fuel redistribution, and fuel melting problems. The specimens were tested in a vacuum chamber using electron bombardment heating. Fuel structural changes were studied using periodic gammagraphs and posttest metallography. The first specimen test was terminated at 50 hours because of a braze failure. The second specimen was tested for 240 hours when an outer clad leak developed due to a tungsten-water reaction. The fuel developed numerous cracks on cooldown but the inner clad remained dimensionally stable. The fuel cover gas did not impede the rate of fuel redistribution. Posttest examination showed the fuel had not melted during operation.

Diianni, D. C.↗
NASA NTRS2008

Thermal Interface Comparisons Under Flight Like Conditions

Thermal interface materials are used in bolted interfaces to promote good thermal conduction between the two. The mounting surface can include panels, heat pipes, electronics boxes, etc.. . On Lunar Reconnaissance Orbiter (LRO) project the results are directly applicable: a) Several high power avionics boxes b) Several interfaces from RWA to radiator through heat pipe network

Rodriquez-Ruiz, Juan↗
DOE OSTI2020

Wire-Based Additive Manufacturing of Stainless Steel Components

In this work three different wire-fed additive manufacturing (AM) processes were employed to evaluate differences between laser, arc, and electron beam heat sources used for high-deposition-rate AM on the order of 1 kg/h. Optimum weld and build parameters were developed independently to match the characteristics of each heat source using 308L stainless steel welding wire as the feedstock. Laser-wire AM was made with the lowest energy per unit length of weld and had the best control of the melt pool and surface finish. Wire arc-based AM had an intermediate energy per unit length of weld of approximately 5× that of the laser process, while electron beam wire AM had the highest energy per unit length of weld at approximately 10× that of the laser process. Analysis of the parts that were built included evaluation of mechanical properties and microstructures, and these properties are discussed with respect to the difference in input energy and cooling rates. Results show that all three processes build parts with properties that exceed those of annealed 304L wrought stainless steel. However, significant differences exist between the processes, and the results presented here can be used to help select the best wire-fed process for a given high-deposition-rate application.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermally Anisotropic Composites for Heat Redirection and Thermal Management in Building Envelopes

In building envelope systems, thermal management is important from energy conservation and thermal comfort perspectives, and is typically done via insulation, thermal mass, solar control and shading, etc. Thermal anisotropy is commonly utilized in electronics for heat dissipation. This article investigates the feasibility of utilizing thermally anisotropic composites (TACs) to reduce unwanted heat gains and losses through the building envelope by redirecting the heat transfer to or from appropriate heat sinks and sources.Numerical simulations of building envelope components using COMSOL Multiphysics and whole building simulations using EnergyPlus (E+) were performed to estimate the energy savings potential of TACs used in external walls of residential buildings. Application of TACs was compared with baseline walls with cavity insulation as well as with and without exterior continuous insulation (CI). The COMSOL simulations indicated 75% or higher reductions in heat gains when using a TAC coupled with a heat sink compared to an exterior CI case. In terms of energy savings in a hot climate, E+ models estimated cooling energy savings of 19% with a "TAC + heat sink" compared to a baseline wall with only cavity insulation. Further, a small-scale test sample with a TAC-heat sink system was built and tested in a multi-transducer heat flow meter (HFM). The heat sink was a copper tube circulating cold water. The experiments verified the re-direction of heat to a sink and significant reduction in heat transfer through the test specimen. The experiments showed that the heat redirection only occurred in the presence of both thermal anisotropy and water circulation; if either element was missing, the system behaved like a traditional envelope component.

Biswas, Kaushik↗
DOE OSTI2024

Overview of the first Wendelstein 7-X long pulse campaign with fully water-cooled plasma facing components

After a long device enhancement phase, scientific operation resumed in 2022. The main new device components are the water cooling of all plasma facing components and the new water-cooled high heat flux divertor units. Water cooling allowed for the first long-pulse operation campaign. A maximum discharge length of 8 min was achieved with a total heating energy of 1.3 GJ. Safe divertor operation was demonstrated in attached and detached mode. Stable detachment is readily achieved in some magnetic configurations but requires impurity seeding in configurations with small magnetic pitch angle within the edge islands. Progress was made in the characterization of transport mechanisms across edge magnetic islands: Measurement of the potential distribution and flow pattern reveals that the islands are associated with a strong poloidal drift, which leads to rapid convection of energy and particles from the last closed flux surface into the scrape-off layer. Using the upgraded plasma heating systems, advanced heating scenarios were developed, which provide improved energy confinement comparable to the scenario, in which the record triple product for stellarators was achieved in the previous operation campaign. However, a magnetic configuration-dependent critical heating power limit of the electron cyclotron resonance heating was observed. Exceeding the respective power limit leads to a degradation of the confinement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2005

A Design of a Modular GPHS-Stirling Power System for a Lunar Habitation Module

Lunar habitation modules need electricity and potentially heat to operate. Because of the low amounts of radiation emitted by General Purpose Heat Source (GPHS) modules, power plants incorporating these as heat sources could be placed in close proximity to habitation modules. A design concept is discussed for a high efficiency power plant based on a GPHS assembly integrated with a Stirling convertor. This system could provide both electrical power and heat, if required, for a lunar habitation module. The conceptual GPHS/Stirling system is modular in nature and made up of a basic 5.5 KWe Stirling convertor/GPHS module assembly, convertor controller/PMAD electronics, waste heat radiators, and associated thermal insulation. For the specific lunar application under investigation eight modules are employed to deliver 40 KWe to the habitation module. This design looks at three levels of Stirling convertor technology and addresses the issues of integrating the Stirling convertors with the GPHS heat sources assembly using proven technology whenever possible. In addition, issues related to the high-temperature heat transport system, power management, convertor control, vibration isolation, and potential system packaging configurations to ensure safe operation during all phases of deployment will be discussed.

Schmitz, Paul C.↗
NASA NTRS2003

Thermo-Electron Ballistic Coolers or Heaters

Electronic heat-transfer devices of a proposed type would exploit some of the quantum-wire-like, pseudo-superconducting properties of single-wall carbon nanotubes or, optionally, room-temperature-superconducting polymers (RTSPs). The devices are denoted thermo-electron ballistic (TEB) coolers or heaters because one of the properties that they exploit is the totally or nearly ballistic (dissipation or scattering free) transport of electrons. This property is observed in RTSPs and carbon nanotubes that are free of material and geometric defects, except under conditions in which oscillatory electron motions become coupled with vibrations of the nanotubes. Another relevant property is the high number density of electrons passing through carbon nanotubes -- sufficient to sustain electron current densities as large as 100 MA/square cm. The combination of ballistic motion and large current density should make it possible for TEB devices to operate at low applied potentials while pumping heat at rates several orders of magnitude greater than those of thermoelectric devices. It may also enable them to operate with efficiency close to the Carnot limit. In addition, the proposed TEB devices are expected to operate over a wider temperature range

Choi, Sang H.↗
DOE OSTI2023

Microstructure and phase evolution in the U-10Zr fuel investigated by in situ TEM heating experiments

The development of U-Zr metallic nuclear fuel for fast spectrum reactors is impacted by a lack of mechanistic understanding of the fuel behavior evolution under thermal irradiation conditions, despite previous works providing substantial fuel performance data. This work uses in-situ transmission electron microscopy heating experiments to study phase and microstructural evolution in several unirradiated U-10Zr specimens during rapid heating ramps (from room temperature to 1000 °C). The starting a-U + bcc-(Zr, U) eutectic microstructure began to decompose above 600 °C. The decomposition initiated from the bcc (U,Zr) phase. Similar results were observed for all specimens even when fabricated by different routes (e.g., cold rolled or annealed). As a result, the impact of observed microstructure and phase evolutions at high temperatures on fuel fabrication and in-pile fuel transient test was also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1982

Recrystallizing Short Lengths of Silicon Ribbon

Silicon recrystallization by laser-beam heating of ribbons proposed. One or both vertical edges of ribbon would not be melted, providing rigid support for moving ribbon. Use of rigid edge means no special atmosphere is required; consequently, electron-beam heating could be used instead of laser-beam heating.

Gurtler, R. W.↗
NASA NTRS1985

The structure of high-temperature solar flare plasma in non-thermal flare models

Analytic differential emission measure distributions have been derived for coronal plasma in flare loops heated both by collisions of high-energy suprathermal electrons with background plasma, and by ohmic heating by the beam-normalizing return current. For low densities, reverse current heating predominates, while for higher densities collisional heating predominates. There is thus a minimum peak temperature in an electron-heated loop. In contrast to previous approximate analyses, it is found that a stable reverse current can dominate the heating rate in a flare loop, especially in the low corona. Two 'scaling laws' are found which relate the peak temperature in the loop to the suprathermal electron flux. These laws are testable observationally and constitute a new diagnostic procedure for examining modes of energy transport in flaring loops.

Emslie, A. G.↗
DOE OSTI2022

Effective Mass from Seebeck Coefficient

Abstract Engineering semiconductor devices requires an understanding of the effective mass of electrons and holes. Effective masses have historically been determined in metals at cryogenic temperatures estimated using measurements of the electronic specific heat. Instead, by combining measurements of the Seebeck and Hall effects, a density of states effective mass can be determined in doped semiconductors at room temperature and above. Here, a simple method to calculate the electron effective mass using the Seebeck coefficient and an estimate of the free electron or hole concentration, such as that determined from the Hall effect, is introduced here is the Seebeck effective mass, n H is the charge carrier concentration measured by the Hall effect ( n H = 1/ eR H , R H is Hall resistance) in 10 20 cm −3 , T is the absolute temperature in K, S is the Seebeck coefficient, and k B / e = 86.3 μV K −1 . This estimate of the effective mass can aid the understanding and engineering of the electronic structure as it is largely independent of scattering and the effects of microstructure (grain boundary resistance). It is particularly helpful in characterizing thermoelectric materials.

Snyder, Gerald Jeffrey↗
DOE OSTI2022

Transient reshaping of intraband transitions by hot electrons

Hot electrons, far above the lattice temperature of a material, present opportunities for enhanced solar energy harvesting or performance of otherwise unfavorable chemistry. The spectroscopic signatures and dynamics of hot carrier absorption and emission have been extensively studied in bulk and nanoscopic semiconductors, but the effects on intraband transitions are largely unexplored. In this work, the effect of hot electrons on the properties of colloidal quantum wells made of cadmium selenide is examined using ultrafast spectroscopy. Similar to expitaxial quantum wells, these atomically precise materials support intersubband transitions (a class of intraband transitions in 1D and 2D materials) in the near-infrared spectral window. Using energy-dependent photoexcitation, it is shown that electrons reach effective temperatures of 2000 K or greater. This results in a substantial transient shift in the oscillator strength of the instersubband transition to lower energies on a sub-picosecond time-scale. Similar heating of electrons is achieved under mid-infrared re-excitation, which permits ultrafast transmittance modulation throughout the near-infrared.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Material Plasma Exposure eXperiment (MPEX) High Heat Flux Bellows for Component Alignment in High Microwave Environment

The Material Plasma Exposure eXperiment (MPEX) device is a linear plasma device developed to perform plasma material interaction experiments under the conditions prototypic of a fusion reactor divertor. MPEX has multiple systems that must be precisely aligned to the plasma axis, including an electron cyclotron heating system that emits up to 400 kW of microwave power into the vacuum vessel. Five distinct systems require precise alignment on the MPEX device, thus requiring four bellows, all of which are adjacent to the plasma at a relatively high heat flux of approximately 47 kW/m2 and microwave power regions. The MPEX high heat flux bellows (HHFB) is designed to deliver 6 degrees of freedom positioning. The HHFB includes titanium–zirconium–molybdenum (TZM) inserts that are brazed into a Glidcop AL-15 body using a high-temperature braze alloy, thus blocking direct line of sight to an edge-welded bellows from the plasma and microwave screen to block microwaves from the bellows. Further, a custom ConFlat knife edge is machined into the Glidcop AL-15, so the vacuum flanges do not need a braze or weld joint on the vacuum interface. Fingerstock or copper mesh is used to restrict microwave power from entering the interstitial space between the water-cooled Glidcop AL-15 body and edge-welded bellows. Glidcop AL-15 was selected as the material of choice for the water-cooled body because it can maintain mechanical integrity at elevated temperatures, and it also allows for a high-temperature braze. TZM was selected for its machinability and compatibility with vacuum and plasma requirements. A test article is also being considered for a similarly shaped component, the MPEX limiter, that will demonstrate the integrity of the braze joint under high thermal load. Results from this testing will be extrapolated to deduce the lifetime and integrity of the HHFB design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗