Search NASA⌕ Search

SEARCH · Search NASA

Results for “FORGING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Strength, Fatigue, and Fracture Toughness of Ti-6Al-4V Liner from a Composite Over-Wrapped Pressure Vessel

It was demonstrated by way of experiment that Composite Over-wrapped Pressure Vessel (COPV) Ti-6Al-4V liner material can sustain the expected service loads and cycles. The experiments were performed as part of investigations on the residual life of COPV tanks being used in Space Shuttle Orbiters. Measured properties included tensile strength, compressive strength, reversed loading cycles to simulate liner proof strains, and cyclic fatigue loading to demonstrate the ability to sustain 1000 cycles after liner buckling. The liner material came from a salvaged 40 in. Columbia (orbiter 102) tank (SN029), and tensile strength measurements were made on both boss-transition (thick) and membrane regions (thin). The average measured yield strength was 131 ksi in the boss-transition and membrane regions, in good agreement with measurements made on 1970 s vintage forged plate stock. However, Young s modulus was 17.4+/-0.3 Msi, somewhat higher than typical handbook values (approx.16 Msi). The fracture toughness, as estimated from a failed fatigue specimen, was 74 ksi/sq in, in reasonable agreement with standardized measurements made on 1970 s vintage forged plate stock. Low cycle fatigue of a buckled test specimen implied that as-imprinted liners can sustain over 4000 load cycles.

Salem, Jonathan A.↗

Advances in Solid State Joining of Haynes 230 High Temperature Alloy

The J-2X engine is being designed for NASA s new class of crew and launch vehicles, the Ares I and Ares V. The J-2X is a LOX/Hydrogen upper stage engine with 294,000 lbs of thrust and a minimum Isp of 448 seconds. As part of the design criteria to meet the performance requirements a large film-cooled nozzle extension is being designed to further expand the hot gases and increases the specific impulse. The nozzle extension is designed using Haynes 230, a nickel-chromium-tungsten-molybdenum superalloy. The alloy was selected for its high strength at elevated temperatures and resistance to hydrogen embrittlement. The nozzle extension is manufactured from Haynes 230 plate spun-forged to form the contour and chemically-milled pockets for weight reduction. Currently fusion welding is being evaluated for joining the panels which are then mechanically etched and thinned to required dimensions for the nozzle extension blank. This blank is then spun formed into the parabolic geometry required for the nozzle. After forming the nozzle extension, weight reduction pockets are chemically milled into the nozzle. Fusion welding of Haynes results in columnar grains which are prone to hot cracking during forming processes. This restricts the ability to use spin forging to produce the nozzle contour. Solid state joining processes are being pursued as an alternative process to produce a structure more amenable to spin forming. Solid state processes have been shown to produce a refined grain structure within the joint regions as illustrated in Figure 1. Solid state joining processes include friction stir welding (FSW) and a patented modification termed thermal stir welding (TSW). The configuration of TSWing utilizes an induction coil to preheat the material minimizing the burden on the weld tool extending its life. This provides the ability to precisely select and control the temperature. The work presented in this presentation investigates the feasibility of joining the Haynes 230 alloy using the solid state welding processes of FSW and TSW. Process descriptions and attributes of each weld process will be presented. Weld process set-up and welding techniques will be discussed leading to the challenges experienced in joining the superalloy. Mechanical property data will also be presented.

Ding, R. Jeffrey↗

Gas Shielding Technology for Welding and Brazing

Welding is a common method that allows two metallic materials to be joined together with high structural integrity. When joints need to be leak-tight, light-weight, or free of contaminant-trapping seams or surface asperities, welding tends to be specified. There are many welding techniques, each with its own advantages and disadvantages. Some of these techniques include Forge Welding, Gas Tungsten Arc Welding, Friction Stir Welding, and Laser Beam Welding to name a few. Whichever technique is used, the objective is a structural joint that meets the requirements of a particular component or assembly. A key practice in producing quality welds is the use of shielding gas. This article discusses various weld techniques, quality of the welds, and importance of shielding gas in each of those techniques. Metallic bonds, or joints, are produced when metals are put into intimate contact. In the solid-state "blacksmith welding" process, now called Forge Welding (FOW), the site to be joined is pounded into intimate contact. The surfaces to be joined usually need to be heated to make it easier to deform the metal. The surfaces are sprinkled with a flux to melt surface oxides and given a concave shape so that surface contamination can be squeezed out of the joint as the surfaces are pounded together; otherwise the surface contamination would be trapped in the joint and would weaken the weld. In solid-state welding processes surface oxides or other contamination are typically squeezed out of the joint in "flash."

Nunes, Arthur J.↗

Using Dust from Asteroids as Regolith Microsamples

Meteorite science is rich with compositional indicators by which we classify parent bodies, but few sample groups are definitively linked with asteroid spectra. More robust links need to be forged between meteorites and their parent bodies to understand the composition, diversity and distribution. A major link can be sample analysis of the parent body material and comparison with meteorite data. Hayabusa, the first sample return mission of the Japanese Aerospace Exploration Agency (JAXA), was developed to rendezvous with and collect samples from asteroid Itokawa and return them to Earth. Thousands of sub-100 micron particles were recovered, apparently introduced during the spacecraft impact into the surface of the asteroid, linking the asteroid Itokawa to LL chondrites [1]. Upcoming missions Hayabusa 2 and OSIRIS-REx will collect more significant sample masses from asteroids. In all these cases, the samples are or will be a collection of regolith particles. Sample return to earth is not the only method for regolith particle analysis. Dust is present around all airless bodies, generated by micrometeorite impact into their airless surfaces, which in turn lofts regolith particles into a "cloud" around the body. The composition, flux, and size-frequency distribution of dust particles can provide significant insight into the geological evolution of airless bodies [2]. For example, the Cassini Cosmic Dust Analyzer (CDA) detected salts in Enceladus' icy plume material, providing evidence for a subsurface ocean in contact with a silicate seafloor [3]. Similar instruments have flown on the Rosetta, LADEE, and Stardust missions. Such an instrument may be of great use in obtaining the elemental, isotopic and mineralogical composition measurement of dust particles originating from asteroids without returning the samples to terrestrial laboratories. We investigated the ability of a limited sample analysis capability using a dust instrument to forge links between asteroid regolith particles and known meteorite groups. We further set limits on the number of individual particles statistically needed to robustly reproduce a bulk composition.

microsamples↗

Thermophysical Properties of Nickel-Based Superalloys

The NASA Marshall Space Flight Center (MSFC) electrostatic levitation (ESL) laboratory has a long history of providing materials research and thermophysical property data. The lab can measure thermophysical properties such as density, surface tension, and viscosity of liquid materials, including elements, alloys, glasses, ceramics, and oxides. Nickel-based superalloys (e.g. Inconel, Hastelloy, and Waspaloy) have many high performance applications, including turbine engines for aerospace. Superalloy parts are typically manufactured by casting and forging. These processes generate both polycrystalline and monocrystalline parts. A relatively new method of fabrication of turbine disk materials is additive manufacturing, which is typically done for aerospace parts by powder-bed methods such as selective laser melting (SLM). Accurate modeling of casting and forging, as well as additively manufacturing processes, require thermophysical properties (density, surface tension, and viscosity). The thermophysical properties of liquid nickel-based superalloys, both conventional and additively manufactured, were measured at several temperatures in both undercooled and superheated condition. Surface tension and viscosity was measured using the oscillating drop method and density and thermal expansion was measured using edge detection methods.

SanSoucie, Michael P.↗

Developments on Low Cost Manufacturing Methods for Cylindrical Launch Vehicle Structures

Due to the increasing international competition and growing pressure to lower the cost of launch vehicles, enhanced technologies and competences for efficient, low cost manufacturing have to be developed. In this paper, an innovative manufacturing technology for launch vehicle applications is presented that was developed over the last few years at MT Aerospace AG (MTA) in collaboration with NASA Langley Research Center, the European Space Agency (ESA), Lockheed Martin Corporation (LMCO), Leifeld Metal Spinning and Scot Forge. The Integrally Stiffened Cylinder (ISC) manufacturing method was first investigated in 2010. Early results indicated a high mass saving potential for cylindrical structures for launch vehicle systems, such as cryogenic tank barrels and intertanks, produced using the ISC method. Cost-benefit studies conducted at NASA and MTA estimated up to 50% reduction in manufacturing costs is possible compared to conventional multi-piece, welded fabrication methods. Associated reductions in manufacturing lead times have shown that a 40% faster production rate is possible by the ISC process. Following proof of concept and process development efforts, a cylindrical structure manufactured using the ISC method had its maiden flight in 2015 on a Black Brant sounding rocket at NASA Wallops Flight Facility. Further collaboration between ESA, NASA, MTA, LMCO, and Scot Forge led to manufacturing test campaigns at MT Aerospace in 2017 and 2018 that successfully demonstrated ISC fabrication at a scale representative of commercial launch vehicles. This paper summarizes the status and relevant results of the development sequence of the ISC cylinder manufacturing method. Results of cost / benefit and structural performance analyses are also summarized. Moreover, an outlook will be given on further planned activities and development steps.

Martin Stachulla↗

Lake Arrowhead Microbial Genomics Conference

The Lake Arrowhead Microbial Genomics Conference (formerly the E. coli and Small Genomes Conference, and the Microbial Genomes Conference) was held September 16-20, 2018, at the UCLA Conference Center at Lake Arrowhead, California. This conference is part of a yearly meeting initiated in 1991 to bring together genome sequencers, bioinformatics specialists, biologists, and geneticists, to forge interactions that would result in meaningful functional genomics. The goal of the meeting was to translate the influx of new genome sequencing information into useful biological studies. The Lake Arrowhead 2018 meeting had a major focus on microbial communities, the human microbiome, pathogens, bioenergetics, and environmental microbiology. The field of genomics has reached the point where deriving the sequence of an organism’s entire genome is now seen as a beginning rather than an endpoint. Moreover, understanding the sequences of whole communities, and particularly those that make up different microbiomes, is now a central point of the field. The 2018 meeting covered microorganisms for which extensive analyses exist, and those for which new biological and technical strategies are being developed. The focus on biodiversity, the human microbiome, pathogenic organisms, and bioenergetics added special significance to this meeting. This meeting was designed to have a mix of 34 invited presentations and poster sessions with 80 posters, and had 160 participants. This meeting has become established as a major annual microbial genomics conference during the last 26 years and has assured status and quality. It offers a major opportunity for young investigators and students to attend, present posters, and give talks. In fact, 22 of the 34 invited speakers were early career stage scientists. An important impact of the conference was the forging of new collaborations between scientists and particularly young scientists with the array of multidisciplinary researchers at the meeting.

Miller, Jeffrey H.↗

Level 2 Milestone Report – Additively Manufactured 304L Stainless Steel

The purpose of this milestone was to support an active research project at Los Alamos National Laboratory to determine the dynamic properties, specifically the equation of state, of additively manufactured (AM) 304L stainless steel and compare to those of forged metal. Our contribution was to measure the shock Hugoniot of AM 304L stainless steel in both the build (growth) and in-plane (transverse) directions and compare those results to similar measurements in forged 304L. These experiments were conducted on the C3 Launcher located in North Las Vegas.

304L stainless steel↗

Thermal and Mechanical Energy Performance Analysis of Closed-loop Systems in Hot-Dry-Rock and Hot-Wet-Rock Reservoirs

To understand the potential and limitations for recovering thermal and mechanical energy from closed-loop geothermal systems a collaborative study is underway that will investigate an array of system configurations, working fluids, geothermal reservoir characteristics, operational periods, and heat transfer enhancements. Closed-loop geothermal systems are distinguished from hydrothermal or enhanced geothermal systems (EGS) in that the working fluid only circulates through drilled boreholes. Principal objectives of this study are to determine upper limits for thermal and mechanical energy recovery and optimal operational and configuration parameters for each scenario. Teams of scientists and engineers are applying a suite of numerical simulation and analytical tools to model the heat recovery from closed-loop geothermal systems, and then optimizing operational and configuration parameters to maximize the thermal and mechanical energy recovery. Results from the suite of numerical simulators and analytical tools, such as outlet and inlet states and temperature profiles in the geothermal reservoir over time are intercompared to increase confidence in the analysis. This paper documents the study findings for closed-loop systems in hot-dry-rock and hot-wet-rock reservoirs, where water is the working fluid. The characteristics of the hot-dry-rock reservoir were based on the U.S. Department of Energy's Utah Frontier Observatory for Research in Geothermal Energy (FORGE) site, near Milford Utah. Two objective functions are defined to optimize the operational and configuration parameters of the system, one each for the recovery of mechanical and thermal energy over the period of operation. For both objective functions, a surface plant thermal to mechanical energy conversion factor and an energy drilling cost is required. In keeping with the study objectives the surface plant conversion factor is determined from a second-law of thermodynamics analysis of a generic binary plant, and drilling costs are based on those from the Utah FORGE site and current national electrical costs.

closed-loop geothermal systems↗

Thermal and Mechanical Energy Performance Analysis of Closed-loop Systems in Hot-Dry-Rock and Hot-Wet-Rock Reservoirs

To understand the potential and limitations for recovering thermal and mechanical energy from closed-loop geothermal systems a collaborative study is underway that will investigate an array of system configurations, working fluids, geothermal reservoir characteristics, operational periods, and heat transfer enhancements. Closed-loop geothermal systems are distinguished from hydrothermal or enhanced geothermal systems (EGS) in that the working fluid only circulates through drilled boreholes. Principal objectives of this study are to determine upper limits for thermal and mechanical energy recovery and optimal operational and configuration parameters for each scenario. Teams of scientists and engineers are applying a suite of numerical simulation and analytical tools to model the heat recovery from closed-loop geothermal systems, and then optimizing operational and configuration parameters to maximize the thermal and mechanical energy recovery. Results from the suite of numerical simulators and analytical tools, such as outlet and inlet states and temperature profiles in the geothermal reservoir over time are intercompared to increase confidence in the analysis. This paper documents the study findings for closed-loop systems in hot-dry-rock and hot-wet-rock reservoirs, where water is the working fluid. The characteristics of the hot-dry-rock reservoir were based on the U.S. Department of Energy’s Utah Frontier Observatory for Research in Geothermal Energy (FORGE) site, near Milford Utah. Two objective functions are defined to optimize the operational and configuration parameters of the system, one each for the recovery of mechanical and thermal energy over the period of operation. For both objective functions, a surface plant thermal to mechanical energy conversion factor and an energy drilling cost is required. In keeping with the study objectives the surface plant conversion factor is determined from a second-law of thermodynamics analysis of a generic binary plant, and drilling costs are based on those from the Utah FORGE site and current national electrical costs.

Closed-loop geothermal systems, hot-dry-rock, hot-↗

Lake Arrowhead Microbial Genomics Conference

The Lake Arrowhead Microbial Genomics Conference (formerly the E. coli and Small Genomes Conference, and the Microbial Genomes Conference) was held September 11-15, 2022, at the UCLA Conference Center at Lake Arrowhead, California. This conference is part of a yearly meeting initiated in 1991 to bring together genome sequencers, bioinformatics specialists, biologists, and geneticists, to forge interactions that would result in meaningful functional genomics. The goal of the meeting was to translate the influx of new genome sequencing information into useful biological studies. The Lake Arrowhead 2022 meeting had a major focus on microbial communities, the human microbiome, pathogens, phage therapy, bioinformatic methods of analysis, bioenergenics, and environmental microbiology. The field of genomics has reached the point where deriving the sequence of an organism’s entire genome is now seen as a beginning rather than an endpoint. Moreover, understanding the sequences of whole communities, and particularly those that make up different microbiomes, is now a central point of the field. The 2022 meeting covered microorganisms for which extensive analyses exist, and those for which new biological and technical strategies are being developed. The focus on biodiversity, the human microbiome, pathogenic organisms and methods of countering them, and bioenergetics added special significance to this meeting. This meeting was designed to have a mix of 36 invited presentations and poster sessions with more than 80 posters, and had 147 participants. This meeting has become established as a major annual microbial genomics conference during the last 29 years and has assured status and quality. It offers a major opportunity for young investigators and students to attend, present posters, and give talks. In fact, 50% of the invited speakers were early career stage scientists. An important impact of the conference was the forging of new collaborations between scientists and particularly young scientists with the array of multidisciplinary researchers at the meeting.

Miller, Jeffrey H.↗

Shallow Geothermal Resources for Cooling Applications at the University of Hawai'i

Drilling activities account for 30% to 57% of the cost to develop and install a geothermal plant. Therefore, an accurate representation of the cost to drill a well is paramount in techno-economic analysis to determine the feasibility of a geothermal power project. In 2022, the National Renewable Energy Laboratory (NREL) endeavored to revise the U.S. Department of Energy (DOE) GeoVision baseline drilling cost curves due to extensive improvement in drilling rates at the Utah Frontier Observatory Research in Geothermal Energy (FORGE) demonstration site. That effort did not culminate in the recommendation of new curves because the actual project costs did not match the reported performance improvements and were at or above the GeoVision baseline. The need for another iteration of this analysis has arisen from industry record drilling performance reported by recent commercial field-scale and demonstration projects, including Fervo Energy's Cape Station, the Utah FORGE 16B(78)-32 demonstration and the Geysers Power Company's GDC-36 demonstration. Therefore, in this work, we have estimated the resulting industry average rate of penetration (ROP) and bit life and applied these parameters as inputs to the Well Cost Simplified model used in the GeoVision analysis. The resulting revised cost curves show a significant decline from the GeoVision baseline. For vertical wells, the magnitude of cost decline ranges between 12% and 24% while for deviated wells, cost reductions between 18% and 26% are estimated. The revised cost curves are in good agreement with actual cost data and therefore, quantify the economic impact of the utilization of (and advances in) polycrystalline diamond compact (PDC) bit technology and the application of physics-based methodologies that optimize mechanical specific energy.

building cooling↗

2025 Geothermal Drilling Cost Curves Update: Preprint

Drilling activities account for 30% to 57% of the cost to develop and install a geothermal plant. Therefore, an accurate representation of the cost to drill a well is paramount in techno-economic analysis to determine the feasibility of a geothermal power project. In 2022, the National Renewable Energy Laboratory (NREL) endeavored to revise the U.S. Department of Energy (DOE) GeoVision baseline drilling cost curves due to extensive improvement in drilling rates at the Utah Frontier Observatory Research in Geothermal Energy (FORGE) demonstration site. That effort did not culminate in the recommendation of new curves because the actual project costs did not match the reported performance improvements and were at or above the GeoVision baseline. The need for another iteration of this analysis has arisen from industry record drilling performance reported by recent commercial field-scale and demonstration projects, including Fervo Energy’s Cape Station, the Utah FORGE 16B(78)-32 demonstration and the Geysers Power Company’s GDC-36 demonstration. Therefore, in this work, we have estimated the resulting industry average rate of penetration (ROP) and bit life and applied these parameters as inputs to the Well Cost Simplified model used in the GeoVision analysis. The resulting revised cost curves show a significant decline from the GeoVision baseline. For vertical wells, the magnitude of cost decline ranges between 12% and 24% while for deviated wells, cost reductions between 18% and 26% are estimated. The revised cost curves are in good agreement with actual cost data and therefore, quantify the economic impact of the utilization of (and advances in) polycrystalline diamond compact (PDC) bit technology and the application of physics-based methodologies that optimize mechanical specific energy.

15 GEOTHERMAL ENERGY↗

The Influence of Warm abc-Pressing on the Structure and Mechanical Properties of Stable Chromium-Nickel-Molybdenum Steel

The structure and properties of the 17Cr13Ni3Mo0.01C stable austenitic steel subjected to high-temperature plastic deformation by the abc-pressing (multiaxial forging) are investigated in the temperature range from 800 to 600°С. The results of investigations demonstrate that after the abc-pressing the steel has a single-phase austenitic ultrafine-grained structure with the size of its elements (grains and subgrains) of (200 ± 140) nm. The formation of the ultrafine-grained state increases the strength properties (0.2 proof stress increases threefold) and decreases the elongation value of the steel at room temperature compared to the coarse-grained specimens. An analysis of the contributions from hardening during abc-pressing evidences in favor of the strength improvement being primarily due to the grain refinement; it is well described by the Hall–Petch relationship. In this case steel with ultrafine-grained austenitic structure exhibits an effect of structural superplasticity at the temperatures T > 750°С: the elongation value at Т = 800°С is found to be 180%.

36 MATERIALS SCIENCE↗

Tribological Performance of Austempered and Tempered Ductile Iron

Austempered ductile iron with its unique ausferritic structure is produced by an isothermal heat treatment process. Austempered ductile iron is a potential material to substitute for traditional steel castings and forgings in current industry due to its excellent mechanical properties. The tempering process is frequently used to enhance the ductility and toughness of a material and reduce residual stress. In this research, the phase transformation of austempered ductile iron was studied by applying various tempering temperatures with constant holding duration. It was found that the ausferritic structure was decomposed into dispersive cementite particles after receiving a tempering temperature of 538 °C or higher. The specific amount of retained austenite was analyzed by X-ray diffraction. The wear resistance of tempered austempered ductile iron was investigated by using a ball-on-disk sliding test configuration. The results were compared with conventional quenched and tempered ductile iron under equivalent hardness. Both austempered ductile iron and tempered austempered ductile iron samples had better wear resistance than quenched and tempered ductile iron. The results presented in this research can be utilized as a reference in the tempering treatment of austempered ductile iron material for future applications.

36 MATERIALS SCIENCE↗

Effect of Temper Condition on the Corrosion and Fatigue Performance of AA2219 Aluminum Alloy

The effect of temper condition and corrosion on the fatigue behavior of alloy AA2219 has been investigated in different temper conditions (T87 and T851). Corrosion testing was performed by exposing the tensile specimens to 3.5% NaCl solution for different time periods, and the corrosion damage was quantified using a 3D profilometer. The exposure-tested specimens were subjected for fatigue testing at different stress levels, and the reduction in fatigue life was measured along with detailed fracture morphology variations. The results indicated that the alloy in both tempers suffers localized corrosion damage and the measured corrosion depth was 120 and 1200 µm, respectively, for T87 and T851 conditions. The loss in fatigue strength was found to be high for T851 (67%) when compared to that of T87 temper condition (58%) for a pre-corrosion time of 15 days. In both cases, fatigue crack initiation is associated with corrosion pits, which act as stress raisers. However, the crack propagation was predominantly transgranular for T87 and a mixed transgranular and intergranular fracture in the case of T851 temper condition. This was shown to be due to the heterogeneous microstructure due to the thermomechanical working and the delay in quench time imposed on the alloy forging in T851 temper condition. The findings in this paper present useful information for the selection of appropriate heat treatment condition to facilitate control of the corrosion behavior which is of great significance for their fatigue performance.

36 MATERIALS SCIENCE↗

Microstructure evolution in TRIP-aided seamless steel tube during T-shape hydroforming process

Transformation-induced plasticity aided seamless steel tube comprising of ferrite, bainite, and metastable austenite was processed through forging, piercing, cold-drawing, and two-stage heat treatment. T-shape hydroforming is a classic forming method for experimental research and practical production. The current work studied austenite-to-martensite transformation and microcrack initiation and propagation of the tube during T-shape hydroforming using electron backscattering diffraction, scanning electron microscopy, and transmission electron microscopy. The strain distribution in the bcc-phase and fcc-phase was studied by evaluating changes in the average local misorientation. Compared to the compressive stress, metastable austenite with similar strain surrounding or inside the grains transformed easier under tensile loading conditions. The inclusions were responsible for microcrack initiation. The propagation of the cracks is hindered by martensite/austenite constituent due to transformation induced plasticity effect. The volume fraction of untransformed retained austenite decreased with increase in strain implying transformation-induced plasticity effect. - Highlights: • Hydroformed tubes processed via TRIP concept • EBSD provided estimate of micro local strain. • Retained austenite hinders propagation of microcracks.

36 MATERIALS SCIENCE↗

Effects of Al-5Ti-1B master alloy on the microstructural evaluation of a highly alloyed aluminum alloy produced by SIMA process

This study was undertaken to investigate the influence of Al-5Ti-1B master alloy on the structural characteristics of Al-12Zn-3 Mg-2.5Cu aluminum alloy. The optimum amount of Ti containing master alloy for proper grain refining was selected as 6 wt.%. A modified strain-induced, melt-activated (SIMA) process for semi-solid processing of alloys was proposed. In order to examine the effectiveness of the modified SIMA process, the recrystallized microstructures of the Al alloy (Al-12Zn-3 Mg-2.5Cu) prepared by the modified SIMA processes were macroscopically. The modified SIMA process employed casting, warm multi-forging, recrystallization and partial melting instead of the conventional process. Reheating condition to obtain a fine globular microstructure was optimized. The microstructure evolution of reheated Al-12Zn-3 Mg-2.5Cu aluminum alloy was characterized by SEM (Scanning electron microscopy) and optical microscopy. In this study the relation between the induced strain with size and shape of grain size has been studied. Results indicated that with the increase of strain sphericity of particles, their size decreases and sphericity takes place in less reahiting time.

36 MATERIALS SCIENCE↗