Search NASA⌕ Search

SEARCH · Search NASA

Results for “FRICTION FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Experimental Studies of Flow Separation of the NACA 2412 Airfoil at Low Speeds

Wind tunnel tests have been conducted on an NACA 2412 airfoil section at Reynolds number of 2.2 x 10(exp 6) and Mach number of 0.13. Detailed measurements of flow fields associated with turbulent boundary layers have been obtained at angles of attack of 12.4 degrees, 14.4 degrees, and 16.4 degrees. Pre- and post-separated velocity and pressure survey results over the airfoil and in the associated wake are presented. Extensive force, pressure, tuft survey, hot-film survey, local skin friction, and boundary layer data are also included. Pressure distributions and separation point locations show good agreement with theory for the two layer angles of attack. Boundary layer displacement thickness, momentum thickness, and shape factor agree well with theory up to the point of separation. There is considerable disparity between extent of flow reversal in the wake as measured by pressure and hot-film probes. The difference is attributed to the intermittent nature of the flow reversal.

Seetharam, H. C.↗

Effect of Stress Ratio on the Fatigue Behavior of a Friction Stir Processed Cast Al-Si-Mg Alloy

The effect of friction stir processing (FSP) on the fatigue life of a cast Al-7Si-0.6Mg alloy at a stress ratio of R=0 was evaluated. Two types of specimen geometry were used for the FSPed condition, through-thickness processed and partial thickness processed. FSP enhanced the fatigue life by a factor of 15 for the through thickness processed samples at lower stress amplitudes. This is different from the FSP specimens tested at R=-1 and similar stress amplitudes where a 5 times improvement in fatigue life was observed. In light of these observations, various closure mechanisms were examined.

36 MATERIALS SCIENCE↗

A hybrid stochastic-deconvolution model for large-eddy simulation of particle-laden flow

We develop a hybrid model for large-eddy simulation of particle-laden turbulent flow, which is a combination of the approximate deconvolution model for the resolved scales and a stochastic model for the sub-grid scales. The stochastic model incorporates a priori results of direct numerical simulation of turbulent channel flow, which showed that the parameters in the stochastic model are quite independent of Reynolds and Stokes number. In order to correctly predict the flux of particles towards the walls an extra term should be included in the stochastic model, which corresponds to the term related to the well-mixed condition in Langevin models for particle dispersion in inhomogeneous turbulent flow. The model predictions are compared with results of direct numerical simulation of channel flow at a frictional Reynolds number of 950. The inclusion of the stochastic forcing is shown to yield a significant improvement over the approximate deconvolution model for the particles alone when combined with a Stokes dependent weight-factor for the well-mixed term.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Geomechanical Characterization and Modeling of the Newark Basin

To ensure long-term safety and containment during geologic carbon sequestration operations, understanding reservoir and cap rock behavior under increased pressure conditions is essential. In particular, the risk of induced seismicity has recently emerged as one of the largest concerns for geologic carbon sequestration and other injection operations. Little observational data are available about induced seismicity risks from carbon dioxide injection. However, an increasing number of earthquakes in the continental United States and worldwide are being attributed to human activities that involve other types of underground injection. Analysis of these events suggests that the net injected volume is one of the key factors, and a prolonged injection of large volumes of carbon dioxide is projected to have high potential for triggering similar seismic events. Increased pore pressure may activate an existing critically stressed discontinuity by reducing its frictional resistance to slip, and cause cap rock failure. Even when facture slip does not produce large seismic events felt by humans or cause visible damage, it can increase formation permeability and compromise cap rock integrity, thus increasing the risk of leakage. The Geomechanical Properties of Mesozoic Basins project performed unique research in the Newark Basin by combining detailed laboratory characterization and rock core testing with novel field operations performed on wireline to measure in-situ stress conditions.

58 GEOSCIENCES↗

Measurements of wind friction speeds over lava surfaces and assessment of sediment transport

Wind velocity profiles were obtained over alluvial plains, lava flows, and a cinder cone in the Mojave Desert to determine the wind shear and the potential for particle transport. It was found that aerodynamic roughness for winds increases nearly a factor of 5 as flow crosses from the alluvium to the lava surface, resulting in wind shear that is 21 percent greater. Thus, wind erosion and sand flux may be substantially enhanced over the lava field. Moreover, wind flow turbulence is enhanced in the wake of the cinder cone, which also increases erosion and sediment transportation by the wind.

Greeley, Ronald↗

Features of the microstructure development under conditions, reproducing the process of friction stir welding. Molecular-dynamics study

Friction stir welding is a recently developed technology which is used in various branches of modern engineering. The basis of this technology is the friction of the rotating cylindrical or specially shaped tool between two metal plates brought together either to meet their ends of one above another with the overlap. When applying the FSW process in various economical sectors, the important task is to study the mechanisms and identify the physical laws and factors leading to formation of structural inhomogeneities and discontinuities in the weld seam. This paper analyzes the basic mechanisms behind the structural state generation in the material subjected to severe plastic deformation and heating. To investigate the atomic mechanisms of structural changes in FSW, the modeling at atomic scale has been carried out. Results of work can be a basis for new knowledge about the microstructure evolution in FSW.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Numerical modeling of geomechanical processes related to CO 2 injection within generic reservoirs

In this project generic anticline structures have been used for numerical modeling analyses to study the influence of geometrical parameters, fluid flow boundary conditions, in situ stress regime and inter-bedding friction coefficient on geomechanical risks such as fracture reactivation and fracture generation. The resulting stress states for these structures are also used to determine safe drilling directions and a methodology for wellbore trajection optimization is developed that is applicable for non-Andersonian stress states. The results of the fluid flow simulation show that the type of fluid flow boundary condition is of utmost importance and has significant impact on all injection related parameters. It is recommended that further research is conducted to establish a method to quantify the fluid flow boundary conditions for injection applications. The results of the geomechanical simulation show that in situ stress regime is a crucial, if not the most important, factor determining geomechanical risks. For extension and strike slip stress regimes anticline structures should be favored over horizontally layered basin as they feature higher ΔP c magnitudes. If sedimentary basins are tectonically relaxed and their state of stress is characterized by the uni-axial strain model the basin is in exact frictional equilibrium and fluids should not be injected. The results also show that low inter bedding friction coefficients effectively decouple layers resulting in lower ΔP c magnitudes, especially for the compressional stress regime.

54 ENVIRONMENTAL SCIENCES↗

K_Road (KRoad)

KRoad is a 2-dimensional, lightweight, vehicle driver simulator that uses 3-dimensional vehicle driving model considerations, i.e. state-of-the-art friction models, and enables the driver to make control decisions with less computation time and programmer effort required than is with full-fidelity 3d simulators. KRoad is fully compatible with OpenAI gym, and contains a factored gym framework for composing gyms from various components (process, reward function, observation function, termination conditions, etc.). KRoad is additionally compatible with the RLlib distributed reinforcement learning environment, running under the Ray distributed python framework.

Tripp, CharlesEdison [National Renewable Energy La↗

Active vibration control in microgravity environment

The low gravity environment of the space station is suitable for experiments or manufacturing processes which require near zero gravity. An experiment was fabricated to test the validity of the active control process and to verify the flow and control parameters identified in a theoretical model. Zero gravity is approximated in the horizontal plane using a low friction air bearing table. An analog control system was designed to activate calibrated air jets when displacement of the test mass is sensed. The experiment demonstrates that an air jet control system introduces an effective damping factor to control oscillatory response. The amount of damping as well as the flow parameters, such as pressure drop across the valve and flow rate of air, are verified by the analytical model.

Gerhold, Carl H.↗

Mechanical strength and tribological behavior of ion-beam deposited boron nitride films on non-metallic substrates

An investigation was conducted to examine the mechanical strength and tribological properties of boron nitride (BN) films ion-beam deposited on silicon (Si), fused silica (SiO2), gallium arsenide (GaAs), and indium phosphide (InP) substrates in sliding contact with a diamond pin under a load. The results of the investigation indicate that BN films on nonmetallic substrates, like metal films on metallic substrates, deform elastically and plastically in the interfacial region when in contact with a diamond pin. However, unlike metal films and substrates, BN films on nonmetallic substrates can fracture when they are critically loaded. Not only does the yield pressure (hardness) of Si and SiO2 substrates increase by a factor of 2 in the presence of a BN film, but the critical load needed to fracture increases as well. The presence of films on the brittle substrates can arrest crack formation. The BN film reduces adhesion and friction in the sliding contact. BN adheres to Si and SiO2 and forms a good quality film, while it adheres poorly to GaAs and InP. The interfacial adhesive strengths were 1 GPa for a BN film on Si and appreciably higher than 1 GPa for a BN film on SiO2.

Miyoshi, Kazuhisa↗

Mechanical strength and tribological behavior of ion-beam-deposited boron nitride films on non-metallic substrates

An investigation was conducted to examine the mechanical strength and tribological properties of boron nitride (BN) films ion-beam deposited on silicon (Si), fused silica (SiO2), gallium arsenide (GaAs), and indium phosphide (InP) substrates in sliding contact with a diamond pin under a load. The results of the investigation indicate that BN films on nonmetallic substrates, like metal films on metallic substrates, deform elastically and plastically in the interfacial region when in contact with a diamond pin. However, unlike metal films and substrates, BN films on nonmetallic substrates can fracture when they are critically loaded. Not only does the yield pressure (hardness) of Si and SiO2 substrates increase by a factor of 2 in the presence of a BN film, but the critical load needed to fracture increases as well. The presence of films on the brittle substrates can arrest crack formation. The BN film reduces adhesion and friction in the sliding contact. BN adheres to Si and SiO2 and forms a good quality film, while it adheres poorly to GaAs and InP. The interfacial adhesive strengths were 1 GPa for a BN film on Si and appreciably higher than 1 GPa for a BN film on SiO2.

Miyoshi, Kazuhisa↗

Finite Element Modeling of the Fiber-Matrix Interface in Polymer Composites

Polymer composites are used in numerous industries due to their high specific strength and high specific stiffness. Composites have markedly different properties than both the reinforcement and the matrix. Of the several factors that govern the final properties of the composite, the interface is an important factor that influences the stress transfer between the fiber and matrix. The present study is an effort to characterize and model the fiber-matrix interface in polymer matrix composites. Finite element models were developed to study the interfacial behavior during pull-out of a single fiber in continuous fiber-reinforced polymer composites. A three-dimensional (3D) unit-cell cohesive damage model (CDM) for the fiber/matrix interface debonding was employed to investigate the effect of interface/sizing coverage on the fiber. Furthermore, a two-dimensional (2D) axisymmetric model was used to (a) analyze the sensitivity of interface stiffness, interface strength, friction coefficient, and fiber length via a parametric study; and (b) study the shear stress distribution across the fiber-interface-matrix zone. It was determined that the force required to debond a single fiber from the matrix is three times higher if there is adequate distribution of the sizing on the fiber. The parametric study indicated that cohesive strength was the most influential factor in debonding. Moreover, the stress distribution model showed the debonding mechanism of the interface. It was observed that the interface debonded first from the matrix and remained in contact with the fiber even when the fiber was completely pulled out.

36 MATERIALS SCIENCE↗

Measurement of local internal friction in metallic glasses

Atomic force acoustic microscopy (AFAM), an advanced scanning probe microscopy technique, has been used to measure local elastic properties with a spatial resolution given by the tip-sample contact radius. AFAM is based on inducing out-of-plane vibrations in the specimen. The vibrations are sensed by the AFM cantilever from by the photodiode signal when its tip is in contact with the material under test. To measure local damping, the inverse quality factor Q{sup −1} of the resonance curve is usually evaluated. Here, from the contact-resonance spectra obtained, we determine the real and imaginary part of the contact stiffness k* and from these two quantities the local damping factor Q{sub loc}{sup −1} is obtained which is proportional to the imaginary part γ of the contact stiffness. The evaluation of the data is based on the cantilever's mass distribution with damped flexural modes and not on an effective point-mass approximation for the cantilever’s motion. The given equation is simple to use and has been employed to study the local Q{sub loc}{sup −1} of amorphous PdCuSi metallic glass and its crystalline counterpart as a function of position of the AFM tip on the surface. The width of the distribution changes dramatically from the amorphous to the crystalline state as expected from the consequences of the potential-energy landscape picture. The center value of the distribution curve for Q{sub loc}{sup −1} coincides very well with published data, based on global ultrasonic or internal friction measurements. This is compared to Q{sub loc}{sup −1} measured in crystalline SrTiO{sub 3}, which exhibits a narrow distribution, as expected.

36 MATERIALS SCIENCE↗

A Multi-Stage Wear Model for Grid-to-Rod Fretting of Nuclear Fuel Rods

The wear of fuel rod cladding against the supporting structures in the cores of pressurized water nuclear reactors (PWRs) is an important and potentially costly tribological issue. Grid-to-rod fretting (GTRF), as it is known, involves not only time-varying contact conditions, but also elevated temperatures, flowing hot water, aqueous tribo-corrosion, and the embrittling effects of neutron fluences. The multi-stage, closed-form analytical model described in this paper relies on published out-of-reactor wear and corrosion data and a set of simplifying assumptions to portray the conversion of frictional work into wear depth. The cladding material of interest is a zirconium-based alloy called Zircaloy-4, and the grid support is made of a harder and more wear-resistant material. Focus is on the wear of the cladding. The model involves an incubation stage, a surface oxide wear stage, and a base alloy wear stage. The wear coefficient, which is a measure of the efficiency of conversion of frictional work into wear damage, can change to reflect the evolving metallurgical condition of the alloy. Wear coefficients for Zircaloy-4 and for a polyphase zirconia layer were back-calculated for a range of times required to wear to a critical depth. Inputs for the model, like the friction coefficient, are taken from the tribology literature in lieu of in-reactor tribological data. Concepts of classical fretting were used as a basis, but are modified to enable the model to accommodate the complexities of the PWR environment. Factors like grid spring relaxation, pre-oxidation of the cladding, multiple oxide phases, gap formation, impact, and hydrogen embrittlement are part of the problem definition but uncertainties in their relative roles limits the ability to validate the model. Sample calculations of wear depth versus time in the cladding illustrate how GTRF wear might occur in a discontinuous fashion during months-long reactor operating cycles. A means to account for grid/rod gaps and repetitive impact effects on GTRF wear is proposed

fretting↗

On the Scaling and Growth Limit of Fluvial Dunes

Abstract Bedforms emerge in a variety of shapes and sizes when a granular erodible surface is subject to a strong enough shear flow, as observed in topographic data from submarine canyons, rivers, deserts, and planetary bodies. The two salient features of bedforms are the ability to collectively transport particles, and to generate form drag thus increasing flow resistance. These two mechanisms are in competition and contribute to force bedforms of increasing size migrating more slowly. In a dedicated large‐scale open channel flow facility, hierarchies of fluvial bedforms were generated and measured in equilibrium conditions. The corresponding scale‐dependent migration velocity and mass flux contributions were quantified in the wave number and frequency domains. Experimental results are paired with a validated set of theoretical models to demonstrate that ripples or dunes reach an equilibrium state when drag partitioning ensures high enough frictional drag to sustain the bedload transport of sediment, and low enough form drag to enable the migration of the largest bedform size. This mechanism is inferred to constrain the growth of bedforms when sediment supply is not the limiting factor.

58 GEOSCIENCES↗

Determining the Mean Frictional Coefficient in Metal Cutting

An analytical formula is derived for determining the frictional coefficient at cutter–blank contact, on the basis of the cutting equations and the shear angle, and is verified by means of experimental data. This formula may be used to calculate the cutting parameters, without constraints on the significant factors.

42 ENGINEERING↗

Physical Properties of Moist, Fermented Corn Grain after Processing by Grinding or Milling

A novel biomass production system, integrating the co-harvesting and co-storage of moist corn grain and stover, promises a reduction in delivered feedstock costs. In this innovative method, the dry grain traditionally utilized for feed or biofuel production will now be processed at a considerably greater moisture content. The adoption of this approach may necessitate a substantial redesign of existing material handling infrastructure to effectively accommodate the handling and storage of moist grain after processing by milling or grinding. A comprehensive study was conducted to quantify the physical properties of this grain after processing with a knife processor or a hammermill. The geometric mean particle size, bulk and tapped density, sliding angle, material coefficient of friction, and discharged angle of repose were quantified. Five grain treatments, either fermented or unfermented, and having different moisture contents, were used. After processing, the moist, fermented ground grain exhibited a significantly smaller particle size compared to the dry grain. Additionally, both moist processed grains resulted in a decreased bulk density and increased material sliding angle, friction coefficient, and angle of repose. The examined metrics collectively suggest that handling, mixing, and storing moist ground grain will pose significant challenges compared to conventional dry ground grain. This increased difficulty may lead to substantially higher costs, a crucial factor that must be carefully considered when evaluating the overall economics of implementing this new biomass production system using combined harvesting and storage of corn grain and stover.

Blazer, Keagan J.↗

Tidal rigidity of Phobos

A novel scenario is proposed in which the orbital eccentricity of Phobos results from several gravitational resonance excitations within the past one billion years, assuming that tidal friction in Phobos has had only a small effect on its orbit. Both the primordial eccentricity and inclination may have been much smaller than presently observed. Constraints imposed on tidal friction in Phobos by the apparent age of its surface, which is greater than one billion years, in addition to those of the gravitational resonance excitation scenario, can be satisfied only if the product of the rigidity and the Q factor is greater than 10 to the 12th dynes/sq cm. In view of the fact that the Q factor is only about 100, so that the rigidity must be greater than 10 to the 10th dynes/sq cm, Phobos should have substantial internal strength.

Yoder, C. F.↗