Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Ultrafine gradient microstructure induced by severe plastic deformation under sliding contact conditions in copper

Highlights: • Sliding contact produces a gradient microstructure by severe plastic deformation. • Nanohardness is increased strongly by grain size and dislocation hardening. • The texture components in the deformed layer correspond to pure shear. • Grain size distribution, boundary misorientation and KAM were analysed. • Strain induced effects compete with crystallisation to determine the microstructure. - Abstract: Sliding contact induces severe plastic deformation (SPD) at the surface of ductile materials and induces a microstructural gradient associated to a significant increase of hardness toward the surface. This gradient allows observing all stages of grain refinement in SPD, as illustrated here by the analysis of polycrystalline electrolytic copper tested in a coaxial tribometer. Materials tested in the cold-rolled state and after annealing were characterised by high-resolution electron backscattering diffraction and nano-indentation. The incremental plastic strain produces an ultrafine microstructure in the top layers, which gradually changes to the original size in unaffected material. In cold-rolled material, an intermediate recrystallised layer is observed. The separation of the Misorientation Angle Distribution (MAD) in a low-angle portion and a high angle portion allows characterising the accumulation of strain induced misorientation, while the Kernel Average Misorientation (KAM) provides information on the evolution of substructure at the finest levels. The results point toward a process where strain-induced effects compete continuously with recrystallisation, except for the surface layer in the cold-rolled material, where dynamic recrystallisation is dominant. Combining the information from KAM and subgrain size distribution, the measured hardness can be explained as a combination of grain size and dislocation hardening.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior and Microstructural Evolution of Antibacterial Austenitic Stainless Steel Containing 3.60% Cu

Hot deformation behavior of as-cast antibacterial austenitic stainless steel containing 3.60% copper was investigated in a temperature range of 900-1150 °C and strain rate range of 0.01-20 s{sup −1}. At strain rates higher than 1 s {sup −1}, the flow stress curves were corrected considering adiabatic heating. Kinetic analysis indicated that the hot deformation activation energy of steel was 376.02 kJ mol{sup −1}. The microstructural evolution under different temperatures was observed by optical microscopy. The nucleation sites for recrystallization and different orientations and twin ratios under different strain rates were analyzed by electron backscatter diffraction. The results showed that hot deformation was dominated by continuous dynamic recrystallization in the high-temperature and high-strain-rate region (1050-1150 °C, 1-20 s{sup −1}). On increasing the temperature and strain rate, the degree of recrystallization and twinning increased simultaneously. These phenomena promoted one another. Thus, the volume fraction of the recrystallized and twinned grains increased with the addition of Cu.

36 MATERIALS SCIENCE↗

Microchemical evolution of irradiated additive-manufactured HT9

The microstructural responses under 5 MeV Fe2 + single-ion-beam irradiation of three conditions of additive-manufactured (AM) HT9 steel using a powder-based directed energy deposition (DED) technique with and without postbuild heat treatments were investigated. Besides the observed dislocation loop formation and the absence of cavities at the irradiation condition of 50 dpa at 460 °C, Ni/Si/Mn-rich precipitates are found to form in all three conditions of AM-HT9, whereas Cu-rich clusters that arise from Cu uptake from the DED process are only observed in the heat-treated conditions, and not in the as-built (ASB) condition. Coprecipitation of the Cu- and Ni/Si/Mn-rich clusters occur near defect sinks such as line dislocations and grain boundaries in the heat-treated AM-HT9. The variation in microchemical evolution can be directly linked to the starting sink strength of the three AM-HT9 conditions, and the ASB condition with higher sink strength suppressed the responses observed in the postbuild heat-treated specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure evolution in TRIP-aided seamless steel tube during T-shape hydroforming process

Transformation-induced plasticity aided seamless steel tube comprising of ferrite, bainite, and metastable austenite was processed through forging, piercing, cold-drawing, and two-stage heat treatment. T-shape hydroforming is a classic forming method for experimental research and practical production. The current work studied austenite-to-martensite transformation and microcrack initiation and propagation of the tube during T-shape hydroforming using electron backscattering diffraction, scanning electron microscopy, and transmission electron microscopy. The strain distribution in the bcc-phase and fcc-phase was studied by evaluating changes in the average local misorientation. Compared to the compressive stress, metastable austenite with similar strain surrounding or inside the grains transformed easier under tensile loading conditions. The inclusions were responsible for microcrack initiation. The propagation of the cracks is hindered by martensite/austenite constituent due to transformation induced plasticity effect. The volume fraction of untransformed retained austenite decreased with increase in strain implying transformation-induced plasticity effect. - Highlights: • Hydroformed tubes processed via TRIP concept • EBSD provided estimate of micro local strain. • Retained austenite hinders propagation of microcracks.

36 MATERIALS SCIENCE↗

Elevated temperature microstructure evolution of a medium-entropy CrCoNi superalloy containing Al,Ti

A new medium-entropy superalloy was produced based on the compositions of equiatomic CrCoNi and Ni-base superalloy Inconel 740H. Initial alloy design was performed using Thermo-Calc. The aging response and microstructural stability were assessed following heat treatment at temperatures between 600 and 900 °C and durations up to 100 h. Aging from a fully recrystallized state resulted in negligible grain growth and produced γ’ and σ phases. The same phases were present after aging from a cold-rolled state, but partially recrystallized microstructures resulted in multi-modal size distributions and heterogeneous spatial arrangements. Finally, room temperature hardness measurements were used to correlate aging conditions with quantitative precipitate measurements and mechanical properties.

36 MATERIALS SCIENCE↗

Sandy Soil Microaggregates: Rethinking Our Understanding of Hydraulic Function

Core Ideas Sandy soil microaggregates are comprised of a solid sand core encrusted with fines. Thick films control a significant proportion of water retention in coarse sandy soil. Three water pools drain sequentially: capillary water, thick films, and adsorptive films. Film seepage rates should be considered when irrigating sandy soil. This study investigated the peculiar structure of microaggregates in coarse sandy soils that exhibit only external porosity and investigated their control on soil hydrology. The microstructure underpins a hydrologic existence that differs from finer textured soils where aggregates have internal porosity. Understanding the impact of these microaggregates on soil hydrology will permit improved agricultural irrigation management and estimates associated with ecosystem capacity and resiliency. Microstructure was investigated using a digital microscope, and aspects of the structure were quantified by sedimentation and computed microtomography. Sandy soil microaggregates were observed to be comprised of a solid sand‐grain core that is coated with fines, presumably cemented by organic media. This microstructure leads to three distinct water pools during drainage: capillary water, followed by thick films (1–20 μm) enveloping the outer surfaces of the crusted microaggregates, followed by adsorbed thin films (<1 μm). The characteristics of the thick films were investigated using an analytical model. These films may provide as much as 10 to 40% saturation in the range of plant‐available water. Using lubrication theory, it was predicted that thick film drainage follows a power law function with an exponent of 2. Thick films may also have a role in the geochemical evolution of soils and in ecosystem function because they provide contiguous water and gas phases at relatively high moisture contents. And, because the rough outer crust of these microaggregates can provide good niches for microbial activity, biofilm physics will dominate thick film processes, and consequently hydrologic, biologic, and geochemical functions for coarse sandy soils.

Paradiś, Ashley↗

Crystal plasticity investigation of the microstructural factors influencing dislocation channeling in a model irradiated bcc material

We use a continuum crystal plasticity framework to study the effect of microstructure and mesoscopic factors on dislocation channeling and flow localization in an irradiated model bcc alloy. For simulated dislocation channeling characteristics we correlate the dislocation and defect densities in the substructure, local Schmid factor, and stress triaxiality, in terms of their temporal and spatial evolution. A metric is introduced to assess the propensity for localization and is correlated to the grain-level Schmid factor. We also found that localization generally takes place in grains with a local Schmid factor in the range 0.42 or higher. Surface slip step heights are computed at free surfaces and compared to relevant experiments.

36 MATERIALS SCIENCE↗

Synergistic effect of microstructure and defects on the initiation of fatigue cracks in additively manufactured Inconel 718

Fatigue cracks in additively manufactured (AMed) Inconel 718 (IN-718) in machined surface condition often initiate from persistent slip bands (PSBs) unlike other popular AM alloys such as 17-4 PH stainless steel or Ti-6Al-4V, where fatigue crack initiation is exclusively from volumetric defects; therefore, a competition between PSB- vs. defect- mediated crack initiation clearly exists. To shed light on the factors governing the competition, this study investigates the characteristics of cyclic strain localization, PSB formation, and crack initiation via crystal plasticity (CP) modeling of cyclic loading on polycrystalline aggregates which are then validated by experiments. In this work, a physics-based, free slip distance (FSD) dependent slip strength evolution law is proposed, which is shown to enable the CP model to simulate the heterogeneous strain distribution in IN-718. Implementing a crack initiation criterion based on strain contrast, the locations and lives for crack initiation can also be calculated. It is shown that both FSD and resolve shear stress influence the strain localization and crack initiation behaviors. The distribution of a localization parameter calculated based on the multiplication of FSD and Schmid factor within a grain is found to correlate well with the locations of PSBs. The maximum values of the localization parameters within a microstructure are shown to correlate well with the experimentally obtained crack initiation lives. The presence of volumetric defects in IN-718 generally do not impact strain localization behavior unless their size is large compared to the grain size.

42 ENGINEERING↗

Atomistic Simulations in Support of UO{sub 2} Fuel Performance Modeling

Large fission gas atoms such as Xe have very low solubility in the UO{sub 2} fuel matrix, which drives precipitation and growth of intra-granular fission gas bubbles, segregation of gas atoms to grain boundaries and evolution of intergranular bubbles. The inter-granular bubbles develop percolation networks leading to release of the fission gas. Fission gas bubbles induce fuel swelling and the fuel thermal conductivity is reduced by both fission gas bubbles and dispersed gas atoms. When fission gas is released from the fuel to the plenum, the pressure on the clad walls increases and the gap thermal conductivity decreases. All of these detrimentally affect fuel performance. The thermal conductivity of UO{sub 2} is low across a wide temperature range compared to iso-structural materials such as ThO{sub 2}, which is caused by the coupling between phonons carrying heat and uranium spins or magnetism providing a scattering mechanism with very low mean free path. For in-pile conditions the thermal conductivity is further reduced due to, for example, radiation damage, generation of fission products and fission gases and fuel microstructure evolution. This results in a complex burn-up dependent thermal conductivity. Thermal conductivity and fission gas evolution are two of the most important properties determining UO{sub 2} nuclear fuel performance. Both properties have significant uncertainty. In order to reduce this uncertainty, new models are being developed based on multi-scale simulations that attempt to improve the description of material properties and also couple them to the microstructure state of the material. In this paper we highlight atomistic calculations and simulations used to develop meso-scale models of the evolution of fission gases and thermal conductivity in UO{sub 2}. Literature examples of the application of these results and the corresponding models to fuel performance simulations will also be given. (author)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Studies on Bio-acceptability of Thermo-Mechanically Processed Mg-4Li-0.5Ca Alloy and Its Microstructural Correlation

In this study, in vitro corrosion behavior of rolled Mg-4Li-0.5Ca (wt.%) alloy at three temperatures (250, 300 and 350 °C) with 75% reduction and subsequent short annealing at 200 °C for 10 min was systematically investigated. Microstructural evaluation, Mg{sub 2}Ca precipitation and defects like twins were characterized by an optical microscope, scanning electron microscope and x-ray diffraction. Micrographs reveal an increase in grain size and comparatively reduction in twins density population with an increase in hot rolling temperature and subsequent short annealing. In vitro corrosion tests like dynamic bio-corrosion immersion test, hydrogen evolution test and electrochemical linear polarization test were carried out in simulated body fluid. From in vitro corrosion tests, it is observed that the alloy rolled at 350 °C and subsequently short-annealed shows better bio-corrosion resistance than other hot-rolled and short-annealed alloys. This is due to low twins density and uniformly dispersed Mg{sub 2}Ca compound throughout the matrix.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior of Aluminum Alloys AA7010 and AA7075

The hot deformation behavior of high-strength aluminum alloys AA7010 and 5 was studied through hot isothermal compression testing in the temperature regime of 623-723 K (at an interval of 25 K) and at varying strain rates (0.001 to 10 s{sup −1}). The safe zone of hot workability of both the alloys was determined using the instability criteria and correlating with the microstructure evolution. Zener–Hollomon parameters were calculated, and constitutive equations were also derived. Common characteristics observed in both the alloys were adiabatic shear band formation at a temperature of 623 K and strain rate of 10 s{sup −1} and flow localization at combination of all temperatures and high strain rate of 10 s{sup −1} with evolution of very fine recrystallized (DRX) grains. High-temperature resistance to deformation, large extent of recrystallization and relatively larger zone of stable deformation and higher activation energy in Al alloy AA7010 were observed as compared to AA7075. Considering the role of precipitates, dynamic recrystallization was found to have significant role in governing the hot deformation behavior of the alloys. Prediction of constitutive equations was found to be more accurate at higher temperatures and at moderate-to-high strain rates with relatively less error in AA7075 alloy as compared to AA7010 alloy.

36 MATERIALS SCIENCE↗

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗

Toucan: A performance portable, scalable implementation of the DECA algorithm

In the field of additive manufacturing (AM), cellular automata (CA) is extensively used to simulate microstructural evolution during solidification. However, while traditional CA approaches are relatively fast, they still require a substantial number of time steps, are limited to moderate volumes, and are relatively difficult to improve through parallelism due to the highly localized nature of the solidification front. Here, to address these issues of time to solution and load balancing, we introduce Toucan, a parallel, performance-portable, and scalable code written in C++ with the Kokkos library that leverages the discrete event inspired cellular automata (DECA) algorithm to perform parallel-in-time (PinT) grain growth simulations. Toucan effectively mitigates load balancing issues by distributing the computational workload more evenly across processors, enhancing scalability and efficiency. We conduct both strong and weak scaling studies on up to 64 GPUs on the Frontier supercomputer, demonstrating that Toucan significantly outperforms the current state-of-the-art, time-stepped CA code, ExaCA, on both single and multi-GPU simulations. Even in AM-specific weak scaling scenarios, Toucan maintains near-ideal scaling, in contrast to the linear increase observed with ExaCA due to the moving laser raster pattern. This study highlights Toucan’s potential to transform microstructural simulations in AM by radically improving both efficiency and scalability over existing methods.

36 MATERIALS SCIENCE↗

Assessment of metadynamic recrystallization in single copper particle impacts by focused ion beam tomography

We study single Cu-on-Cu impacts relevant to cold spray deposition and quantitatively analyze the metadynamic recrystallization (mDRX) that takes place after the impact by virtue of lingering impact adiabatic heat. Unlike prior studies, the current full 3D tomographic analysis of the mDRX volume shows that mDRX is extremely common in such impacts, although it is often missed when examining 2D sections. We also report an unexpected trend: there is a “sour spot” for mDRX at velocities about 20–40 % above the velocity for particle adhesion. This non-monotonic trend is contrary to the expectations based on increasing adiabatic heating with velocity. With a schematic model, we show that the trend can be explained on the basis of heat transfer: cooling of the heat-affected region is limited by transport through the bonded regions at the particle-substrate interface. Thus, bonding has a prominent role in the heat dissipation process and the best bonded particles most rapidly bulk quench, avoiding mDRX. Here, the developed semi-empirical model aligns with the experimental findings and may help inform microstructural evolution during cold spray and post-spray processing.

FIB-SEM tomography↗

Friction surface layer deposition of triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high entropy alloy: Process optimization and microstructural evolution

A high-strength Co-free triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high-entropy alloy (HEA) was successfully fabricated using Friction Surface Layer Deposition (FSLD), a bulk manufacturing method. Multiple single-layer deposits were produced by varying forging force (F) and traverse speeds (T r ) to optimize the process parameters. The optimized conditions (F = 40 kN & T r = 200 mm/min) were then applied to manufacture a scaled-up multi-layer specimen. The initial microstructure of the HEA consisted of coarse grains of the soft FCC-phase, long columnar dendrites of the hard BCC-phase, and small precipitates of the harder B2-phase within the BCC-dendrites. During FSLD, the FCC-matrix underwent continuous dynamic recrystallization due to high-temperature severe plastic deformation, forming finer equiaxed grains. Simultaneously, the BCC-dendrites fractured into smaller fragments, some of which experienced partial growth and coarsening under applied stress, resulting in an hourglass morphology. In contrast, the small B2-precipitates within the BCC-fragments dissolved during the elevated temperatures of FSLD and reprecipitated as substantially finer precipitates during continuous cooling post-FSLD. Additionally, the orientation relationships between the FCC and BCC/B2 phases were completely destroyed by the severe thermoplastic deformation inherent to FSLD. The microstructural refinements led to a substantial improvement in hardness from 177 HV to 283 HV, driven by Hall-Petch strengthening. The increased number of interfaces, including coherent BCC-B2 interfaces, potentially enhances the sink strength and radiation tolerance of the HEA, making it a promising candidate for nuclear applications. In conclusion, this study also highlights FSLD as a versatile technique for achieving tunable properties in HEAs, with detailed schematics illustrating the complex mechanisms of phase transformations during processing.

Additive Manufacturing↗

Mesoscale modeling of restructuring in high burnup UO 2 fuel

Here, this work aims to simulate the restructuring behavior observed in different regions of high burnup fuel, providing a first-of-its-kind restructuring model for the dark zone and rim region of high-burnup UO 2 fuel. We employed a grand-potential-based phase-field model to concurrently evaluate subgrain formation and the growth of fission gas bubbles within the fuel. An energy-based subgrain formation criterion was introduced to simulate the restructuring process. The effects of different initial conditions and different modeling parameters were systematically studied to capture how each of these parameters influences the characteristics of the restructured fuel. Subgrain formation was observed to begin around existing fission gas bubbles and proceed toward triple junctions, grain boundaries, and grain interiors. Restructuring was demonstrated to be influenced by a combination of initial dislocation densities, burnup rate, subgrain formation rate, and temperature. Under a given subgrain formation rate, the rate of restructuring increases with rising fuel temperature. A restructuring bias was observed within the microstructure, due to the variation in defect accumulation when comparing different grains. Microstructures corresponding to the dark zone and rim region can be obtained by parameterizing the model with the appropriate defect production rate, as determined based on the burnup rate and temperature. Furthermore, bubble size and distribution do not significantly affect the rate of restructuring. The predicted microstructures are consistent with experimental observations of the restructured regions. Finally, we present a correlation demonstrating the evolution of the restructuring volume fraction as a function of local burnup.

UO2↗

The Modified Void Nucleation and Growth Model (MNAG) for Damage Evolution in BCC Ta

A void coalescence term was proposed as an addition to the original void nucleation and growth (NAG) model to accurately describe void evolution under dynamic loading. The new model, termed as modified void nucleation and growth model (MNAG model), incorporated analytic equations to explicitly account for the evolution of the void number density and the void volume fraction (damage) during void nucleation, growth, as well as the coalescence stage. The parameters in the MNAG model were fitted to molecular dynamics (MD) shock data for single-crystal and nanocrystalline Ta, and the corresponding nucleation, growth, and coalescence rates were extracted. The results suggested that void nucleation, growth, and coalescence rates were dependent on the orientation as well as grain size. Compared to other models, such as NAG, Cocks–Ashby, Tepla, and Tonks, which were only able to reproduce early or later stage damage evolution, the MNAG model was able to reproduce all stages associated with nucleation, growth, and coalescence. The MNAG model could provide the basis for hydrodynamic simulations to improve the fidelity of the damage nucleation and evolution in 3-D microstructures.

36 MATERIALS SCIENCE↗

Use of High Magnetic Field to Control Microstructural Evolution in Metallic and Magnetic Materials

The Amendment 1, referred to as Phase 2, to the original CRADA NFE-06-00414 added tasks 3 through 7 to the original statement of work that had two main tasks that were successfully accomplished in Phase 1 of this project. In this Phase 2 CRADA extension, extensive research and development activities were conducted using high magnetic field processing effects for the purpose of manipulating microstructure in the SAE 5160 steel to refine grain size isothermally and to develop nanocrystalline spacing pearlite during continuous cooling, and to enhance the formability/forgability of the non-ferrous precipitation hardening magnesium alloy AZ90 by applying a high magnetic field during deformation processing to investigate potential magnetoplasticity in this material. Significant experimental issues (especially non-isothermal conditions evolving upon insertion of an isothermal sample in the high magnetic field) were encountered in the isothermal phase transformation reversal experiments (Task 4) that later were determined to be due to various condensed matter physics phenomenon such as the magnetocaloric (MCE) effect that occurs in the vicinity of a materials Curie temperature. Similarly the experimental deformation rig had components for monitoring deformation/strain (Task 3) that were susceptible to the high magnetic field of the ORNL Thermomagnetic Processing facility 9-T superconducting magnet that caused electronic components to fail or record erroneous (very noisy) signals. Limited experiments on developing nanocrystalline spacing pearlite were not sufficient to elucidate the impact of high magnetic field processing on the final pearlite spacing since significant statistical evaluation of many pearlite colonies would need to be done to be conclusive. Since extensive effort was devoted to resolving issues for Tasks 3 and 7, only results for these focused activities are included in this final CRADA report along with those for Task 7 (described in the Objectives Section of this report).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗