SEARCH · Search NASA
Results for “Layered cathode”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Erosion behavior of composite Al-Cr cathodes in cathodic arc plasmas in inert and reactive atmospheres
Al{sub x}Cr{sub 1−x} composite cathodes with Al contents of x = 0.75, 0.5, and 0.25 were exposed to cathodic arc plasmas in Ar, N{sub 2}, and O{sub 2} atmospheres and their erosion behavior was studied. Cross-sectional analysis of the elemental distribution of the near-surface zone in the cathodes by scanning electron microscopy revealed the formation of a modified layer for all cathodes and atmospheres. Due to intermixing of Al and Cr in the heat-affected zone, intermetallic Al-Cr phases formed as evidenced by x-ray diffraction analysis. Cathode poisoning effects in the reactive N{sub 2} and O{sub 2} atmospheres were nonuniform as a result of the applied magnetic field configuration. With the exception of oxide islands on Al-rich cathodes, reactive layers were absent in the circular erosion zone, while nitrides and oxides formed in the less eroded center region of the cathodes.
Demarcating the Impact of Electrolytes on High–Nickel Cathodes and Lithium–Metal Anode
The ever-growing demand for low-cost, high-energy-density lithium-ion batteries (LIBs) makes high-nickel layered oxide cathodes, especially LiNiO 2 (LNO), one of the most appealing candidates. However, poor structural and surface instability that leads to a short cycle life remains a formidable challenge. Herein, a systematic investigation of LNO performance in two different electrolytes (a conventional carbonate-based LP57 electrolyte and an ether-based localized high-concentration electrolyte (LHCE)) with different charge cut-off voltages is presented. These findings show that the cathode-electrolyte reactivity is the main factor dictating the performance degradation of LNO at high voltages rather than bulk integrity. While LHCE can provide good stability beyond 4.2 V with a robust, uniform solid–electrolyte interphase (SEI) layer on the Li-metal anode, there is no significant difference in cyclability at 4.15 V (96% capacity retention after 200 cycles) for both LP57 and LHCE. From LNO symmetric cells, carbonate-based electrolyte is found to be good for LNO stability while ether-based electrolyte is beneficial toward Li-metal anode. Furthermore, a suitable electrolyte or a low cut-off voltage is necessary to maintain a decent cycle life. Altogether, this work highlights the impact of electrolyte and cut-off voltage on LNO and Li-metal, which can help guide the development of cells based on LNO.
Air stable organic-inorganic nanoparticles hybrid solar cells
A solar cell includes a low work function cathode, an active layer of an organic-inorganic nanoparticle composite, a ZnO nanoparticle layer situated between and physically contacting the cathode and active layers; and a transparent high work function anode that is a bilayer electrode. The inclusion of the ZnO nanoparticle layer results in a solar cell displaying a conversion efficiency increase and reduces the device degradation rate. Embodiments of the invention are directed to novel ZnO nanoparticles that are advantageous for use as the ZnO nanoparticle layers of the novel solar cells and a method to prepare the ZnO nanoparticles.
Sodium bromide electron-extraction layers for polymer bulk-heterojunction solar cells
Inexpensive and non-toxic sodium bromide (NaBr) was introduced into polymer solar cells (PSCs) as the cathode buffer layer (CBL) and the electron extraction characteristics of the NaBr CBL were investigated in detail. The PSCs based on NaBr CBL with different thicknesses (i.e., 0 nm, 0.5 nm, 1 nm, and 1.5 nm) were prepared and studied. The optimal thickness of NaBr was 1 nm according to the photovoltaic data of PSCs. The open-circuit voltage (V{sub oc}), short-circuit current density (J{sub sc}), fill factor (FF), and power conversion efficiency (PCE) of the PSC with 1 nm NaBr were evaluated to be 0.58 V, 7.36 mA/cm{sup 2}, 0.63, and 2.70%, respectively, which were comparable to those of the reference device with the commonly used LiF. The optimized photovoltaic performance of PSC with 1 nm NaBr was ascribed to the improved electron transport and extraction capability of 1 nm NaBr in PSCs. In addition, the NaBr CBL could prevent the diffusion of oxygen and water vapor into the active layer and prolong the lifetime of the devices to some extent. Therefore, NaBr layer could be considered as a promising non-toxic CBL for PSCs in future.
Understanding the Low Voltage Hysteresis of Anionic Redox in Na2Mn3O7
Explore the source record for details and available documents.
Next-Generation Cobalt-Free Cathodes – A Prospective Solution to the Battery Industry's Cobalt Problem
Lithium-ion batteries are overreliant on cobalt containing cathodes. Current projections estimate that hundreds of millions of electric vehicles (EVs) will be on the road by 2050, and this ever-growing demand threatens to deplete global cobalt reserves at an alarming rate. Moreover, cobalt supply chain issues have significantly increased cobalt prices throughout the last decade. As such, energy storage research and development need to reduce the reliance on cobalt to meet ever-growing demand for lithium-ion batteries. The present review summarizes the science and technology gaps and potential of numerous cobalt-free Li-ion cathodes including layered, spinel, olivine, and disordered rock-salt systems. Despite the promising performance of these Co-free cathodes, scale-up and manufacturing bottlenecks associated with these materials must also be addressed to enable widespread adoption in commercial batteries. Overall, this review broadly highlights the enormous promise of “zero-cobalt” Li-ion batteries to enable sustainable production of EVs in the coming decades.
Stable Cycling with Intimate Contacts Enabled by Crystallinity–Controlled PTFE–Based Solvent–Free Cathodes in All–Solid–State Batteries
All-solid-state batteries (ASSBs) employing Li-metal anodes and inorganic solid electrolytes are attracting great attention due to high safety and energy density for next-generation energy storage devices. However, the volume change of cathode active materials can cause contact loss, resulting in charge carrier isolation, heterogeneous current distribution, and poor electrochemical properties in ASSBs. Here, a simple, yet effective, solvent-free electrode engineering approach with polytetrafluoroethylene (PTFE) as a binder for ASSBs is reported, enabling intimate contact and stable interfaces with the cathode. It is substantiated that the crystallinity of PTFE can be controlled depending on the heat history, and highly crystalline PTFE displays robust mechanical properties. High-nickel LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode prepared with crystalline PTFE show improved cycle and rate performances in ASSBs. In addition, it is revealed that the intimate contact between cathode particles with a stable cathode electrolyte layer is maintained during cycling by postmortem studies. Furthermore, this simple engineering method can be applied to prepare cathodes with a variety of active materials and solid electrolytes in ASSBs.
Evolution of the Electrode–Electrolyte Interface of LiNi 0.8 Co 0.15 Al 0.05 O 2 Electrodes Due to Electrochemical and Thermal Stress
For layered oxide cathodes, impedance growth and capacity fade related to reactions at the cathode–electrolyte interface (CEI) are particularly prevalent at high voltage and high temperatures. At a minimum, the CEI layer consists of Li 2 CO 3 , LiF, reduced (relative to the bulk) metal-ion species, and salt decomposition species, but conflicting reports exist regarding their progression during (dis)charging. Utilizing transport measurements in combination with X-ray and nuclear magnetic resonance spectroscopy techniques in our work, we study the evolution of these CEI species as a function of electrochemical and thermal stress for LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA) particle electrodes using a LiPF 6 ethylene carbonate:dimethyl carbonate (1:1 volume ratio) electrolyte. Although initial surface metal reduction does correlate with surface Li 2 CO 3 and LiF, these species are found to decompose upon charging and are absent above 4.25 V. While there is trace LiPF 6 breakdown at room temperature above 4.25 V, thermal aggravation is found to strongly promote salt breakdown and contributes to surface degradation even at lower voltages (4.1 V). An interesting finding of our work was the partial reformation of LiF upon discharge, which warrants further consideration for understanding CEI stability during cycling.
A Review of the Use of Immobilized Ionic Liquids in the Electrochemical Conversion of CO2
This paper is a review on the application of imidazolium-based ionic liquids tethered to polymer backbones in the electrochemical conversion of CO2 to carbon monoxide and formic acid. These tethered ionic liquids have been incorporated into novel anion ion exchange membranes for CO2 electrolysis, as well as for ionomers that have been incorporated into the cathode catalyst layer, providing a co-catalyst for the reduction reaction. In using these tethered ionic liquids in the cathode catalyst composition, the cell operating current increased by a factor of two or more. The Faradaic efficiencies also increased by 20–30%. This paper provides a review of the literature, in addition to providing some new experimental results from Dioxide Materials, in the electrochemical conversion of CO2 to CO and formic acid.
Scalable and Cost-Effective Barrier Layer Coating to Improve Stability and Performance of SOFC Cathode
During this project, a dense GDC barrier layer was deposited on YSZ substrate to prevent chemical reaction between LSCF and YSZ by a cost-effective EPD method. PPy was used as the agent to make YSZ conductive. Highly compact GDC green layer was obtained by the EPD process in an ethanol-based suspension. The deposition rate on PPy coated YSZ is slower than that on graphite because the charge transfer process is the rate-determining step. The main resistance is from the ion accumulation/depletion zone. The H + ions reduced at the cathode consist of free H + ions and absorbed H + ions corresponding to the unavoidable electrochemical reaction and deposition, respectively. A factor f was introduced to reflects EPD efficiency and describe the competitive relationship between deposition and electrochemical reaction during EPD process. f is in the range from 0 to 0.5 which is determined by the amount ration between free H + ions and absorbed H + ions at the suspension/deposit interface and the conductivity of the cathode. f decreases with the increase of current density or applied voltage and the conductivity of the cathode. GDC thin layers formed by DC-EPD in a thickness range of 5-8 µm were successfully densified at as low as 1300 °C and the adhesion between GDC and YSZ was good. The densification temperature can be further reduced to 1250 °C when AC-EPD was used to replace DC-EPD. The deposition rate increases with the increase of duty cycle and voltage ratio. The deposition rate increases with the increase of frequency from 10 Hz to 500 Hz, while decrease when the frequency increases from 500 Hz to 5000 Hz. Desorption of absorbed charge carrier is easy and irreversible. The deposition rate is independent on the conductivity of the cathode when the electrochemical reaction can be ignored with a high frequency. Inter-diffusion of cation ions between the electrolyte and barrier layer has been systematically characterized via 3-D atom probe, TEM, and other techniques. No measurable Sr transport occurs across the GDC layer with a thickness of 1.5 – 6 μm at a LSCF processing temperature of 1000 °C. However, Sr transport does occur across GDC layer with a thickness of 1.5 or 3 μm at a higher LSCF sintering temperature (1000 °C or 1200 °C). The primary pathway are open pores or grain boundaries in the GDC. The observed zirconate layer is discontinuous even for the most extreme conditions (1.5 μm GDC, 1200 °C LSCF sintering temperature). Increasing the thickness of GDC to 4.5 μm can effectively suppress any zirconate formation measurable by SEM-EDX. Cobalt is observed at grain boundaries within the GDC, suggesting some depletion of Co from the LSCF layer that may ultimately impact electrode performance.
Method of protecting sulfur cathode materials for alkali metal-sulfur secondary battery
Provided is a method of producing a rechargeable alkali metal-sulfur cell, comprising: (a) providing an anode layer; (b) providing particulates comprising primary particles of a sulfur-containing material encapsulated or embraced by a thin layer of a conductive sulfonated elastomer composite, wherein the conductive sulfonated elastomer composite comprises from 0% to 50% by weight of a conductive reinforcement material dispersed in a sulfonated elastomeric matrix material, and the conductive sulfonated elastomer composite has a thickness from 1 nm to 10 μm, a fully recoverable tensile strain from 2% to 500%, a lithium ion conductivity from 10−7 S/cm to 5×10−2 S/cm, and an electrical conductivity from 10−7 S/cm to 100 S/cm; (c) forming the particulates, a resin binder, and an optional conductive additive into a cathode layer; and (d) combining the anode layer, the cathode layer, an optional porous separator, and an electrolyte to form the alkali metal-sulfur cell.
Impact of Anode to Cathode Crossover in Lithium‐metal Batteries With High‐Nickel Cathodes
The advancement of high-energy-density lithium-metal batteries (LMBs) is hindered by the chemical instability of both lithium-metal anode and high-nickel layered oxide cathodes. While cathode-to-anode crossover is well-documented, the reverse process of anode-to-cathode crossover remains underexplored. Here, we systematically investigate such crossovers and the degradation pathway in pouch cells with a localized high-concentration electrolyte, comparing NMC622, NMC811, and NMC90 cathodes paired with lithium-metal and graphite anodes. Despite delivering higher initial capacities, LMBs exhibit faster capacity fade under long-term cycling at 45 °C. To isolate cathode-side degradation, galvanostatic electrochemical impedance spectroscopy (GEIS) measurements of cycled cathodes paired with delithiated lithium iron phosphate (LFP) counter electrodes reveal significantly higher charge-transfer resistance in cathodes cycled with lithium-metal. Surface characterization via X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) reveals greater electrolyte decomposition on cathodes cycled with lithium metal, leading to thicker, more organic-rich cathode–electrolyte interphases (CEIs), consistent with the elevated charge-transfer resistance observed in GEIS measurements. Notably, NMC90 shows the most pronounced CEI thickening, linking higher cathode surface reactivity to greater susceptibility to anode-to-cathode crossover. This work presents compelling evidence of crosstalk degradation originating from lithium-metal anodes and underscores the importance of cross-interface stability for the design of durable LMBs.
Investigation of Cathodes for Next Generation High Energy: Lithium-ion Batteries and Post
Recently, anionic activity, oxygen redox reaction, has been discovered in the electrochemical processes, providing extra reversible capacity for lithium-rich layered oxide cathode. However, the huge irreversible capacity loss in the first charge–discharge cycle and voltage degradation during cycling process prevent their utilization in LIBs. Herein, modified carbonate co-precipitation synthesis without addition of chelating agent is introduced to obtain meso-structure controlled Li-rich layered oxides. This unique design not only decreases surface area compared with the sample with dispersive particles, but also increases overall structure mechanical stability compared with the sample with larger secondary particles as observed by TXM. As a result, the voltage decay and capacity loss during long term cycling have been minimized to a large extent.
Engineering the solid oxide fuel cell electrocatalyst infiltration technique for industrial use
We explore various parameters for infiltrating La 0.6 Sr 0.4 CoO 3-δ (LSCo) into the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) – Ce 0.8 Sm 0.2 O 2 (SDC) cathode of a planar solid oxide fuel cell (SOFC) using an automated solution dispensing technique for commercial deployment of infiltrated SOFCs by industry. Substrate temperature, chelating agent concentration, and surfactant type were explored to develop a 1-step infiltration process for delivering 8–10 weight percent of LSCo electrocatalyst to the cathode active layer. Finally, the results confirm increased fuel cell performance and durability by optimizing the infiltrate solution for increased transport into the cathode's microstructure.
Structural and chemical evolutions of a magnesium vanadium oxide cathode under electrochemical cycling in magnesium batteries
The design of cathode materials that remain chemically and structurally stable during repetitive ion insertion and extraction poses a significant challenge in developing multivalent batteries. The cycling stability of traditional metal oxide-based cathode is challenged by sluggish diffusion of multivalent cations and parasitic reactivity at interfacial regimes, including the cathode electrolyte interphase layer (CEI). Understanding the reactions at the cathode-electrolyte interface, particularly those induced by non-stoichiometric surface layers, is a crucial design parameter for both cathode materials and electrolytes. Here, in this study, we employed multimodal analysis, including in situ and ex situ X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (TEM) and electrochemical impedance spectroscopy (EIS) to examine the surface reactions and subsequent structural and chemical evolutions of the CEI on high voltage magnesium vanadium oxide (MgV 2 O 4 ) spinel cathode during the Mg 2+ insertion/extraction processes. The results revealed that the presence of non-stoichiometric surface layers in the magnesium vanadium oxide cathode drive the decomposition of bis(trifluoromethanesulfonyl)imide (TFSI - ) anion, leading to the formation of the CEI layer. The CEI layer could inhibit the Mg 2+ ion transfer processes. Accompanying this reactivity-driven degradation, the magnesium vanadium oxide cathode undergoes pulverization, forming clusters of nanosized particles. This process likely improves cycling ability by creating new intercalation sites and shortening the diffusion pathway for the Mg 2+ cations. This study demonstrates that controlling surface stoichiometry and engineering morphological properties are critical design parameters for high performance cathodes for multivalent batteries.
Ionic Interdiffusion at Cathode|Solid-Electrolyte Interface: A Machine Learning–Assisted Multiscale Investigation and Mitigation Strategies
Future lithium batteries are expected to use solid electrolytes to achieve higher energy density and fast charge capabilities. However, most solid electrolytes are thermodynamically unstable against layered oxide cathodes. In this study, the stability of LiCoO2 (LCO) cathode with Li10GeP2S12 (LGPS) solid electrolyte is investigated using ab initio molecular dynamics (AIMD) and machine learning molecular dynamics (MLMD). The propensity of ionic interdiffusion, formation of a passivating interphase layer, and corresponding decay in cell performance is addressed using a continuum model. Large-scale MLMD simulations confirm that the LCO|LGPS interface permits interdiffusion of cobalt (Co) and other ionic species, leading to the formation and growth of a resistive interphase and to dramatic capacity fade even in the first cycle. We examine the literature evidence that incorporating a thin layer of LiNb0.5Ta0.5O3 (LNTO) between LCO and LGPS prevents the interdiffusion of ions. Atomistic simulations suggest that substituting lithium (Li) in LNTO with Co is thermodynamically unfavorable, thereby inhibiting ionic interdiffusion. The stable Nb5+/Ta5+ states form a rigid metal-oxide framework, which consequently also prevents the substitution of niobium (Nb) or tantalum (Ta). However, continuum-level analysis suggests that the higher mechanical stiffness of LNTO can lead to interfacial delamination between the LCO and LNTO. This phenomenon reduces the effectiveness of the protective layer. This paper, therefore, highlights the need to develop novel interlayers that balance low ionic interdiffusion with low mechanical stiffness.
Lithium-Doping Stabilized High-Performance P2–Na 0.66 Li 0.18 Fe 0.12 Mn 0.7 O 2 Cathode for Sodium Ion Batteries
While sodium-ion batteries (SIBs) hold great promise for large-scale electric energy storage and low speed electric vehicles, the poor capacity retention of the cathode is one of the bottlenecks in the development of SIBs. Following a strategy of using lithium doping in the transition-metal layer to stabilize the desodiated structure, we have designed and successfully synthesized a novel layered oxide cathode P2–Na 0.66 Li 0.18 Fe 0.12 Mn 0.7 O 2 , which demonstrated a high capacity of 190 mAh g –1 and a remarkably high capacity retention of ~87% after 80 cycles within a wide voltage range of 1.5–4.5 V. Furthermore, the outstanding stability is attributed to the reversible migration of lithium during cycling and the elimination of the detrimental P2–O2 phase transition, revealed by ex situ and in situ X-ray diffraction and solid-state nuclear magnetic resonance spectroscopy.