Search NASA⌕ Search

SEARCH · Search NASA

Results for “Morphology control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Photometric diversity of terrains on Triton

Voyager disk-resolved images of Triton in the violet (0.41 micrometers) and green (0.56 micrometer wavelengths have been analyzed to derive the photometric characteristics of terrains on Triton. Similar conclusions are found using two distinct but related definitions of photometric units, one based on color ratio and albedo properties (A. S. McEwen, 1990), the other on albedo and brightness ratios at different phase angles (P. Lee et al., 1992). A significant diversity of photometric behavior, much broader than that discovered so far on any other icy satellite, occurs among Triton's terrains. Remarkably, differences in photometric behavior do not correlate well with geologic terrain boundaries defined on the basis of surface morphology. This suggests that in most cases photometric properties on Triton are controlled by thin deposits superposed on underlying geologic units. Single scattering albedos are 0.98 or higher and asymmetry factors range from -0.35 to -0.45 for most units. The most distinct scattering behavior is exhibited by the reddish northern units already identified as the Anomalously Scattering Region (ASR), which scatters light almost isotropically with g = -0.04. In part due to the effects of Triton's clouds and haze, it is difficult to constrain the value of bar-theta, Hapke's macroscopic roughness parameter, precisely for Triton or to map differences in bar-theta among the different photometric terrains. However, our study shows that Triton must be relatively smooth, with bar-theta less than 15-20 degs and suggests that a value of 14 degs is appropriate. The differences in photometric characteristics lead to significantly different phase angle behavior for the various terrains. For example, a terrain (e.g., the ASR) that appears dark relative to another at low phase angles will reverse its contrast (become relatively brighter) at larger phase angles. The photometric parameters have been used to calculate hemispherical albedos for the units and to infer likely surface temperatures. Based on these results, we determine that all but the most southerly regions (i.e., mostly south of the equator) of the reddish northern terrains are likely to have been covered with deposits of nitrogen frost at the time of the Voyager flyby, in agreement with the suggestion from the photometry that these units are overlain by a thin veneer of material.

Hillier, J.↗

Assessment of Postflight Locomotor Performance Utilizing a Test of Functional Mobility: Strategic and Adaptive Responses

Space flight induces adaptive modification in sensorimotor function, allowing crewmembers to operate in the unique microgravity environment. This adaptive state, however, is inappropriate for a terrestrial environment. During a re-adaptation period upon their return to Earth, crewmembers experience alterations in sensorimotor function, causing various disturbances in perception, spatial orientation, posture, gait, and eye-head coordination. Following long duration space flight, sensorimotor dysfunction would prevent or extend the time required to make an emergency egress from the vehicle; compromising crew safety and mission objectives. We are investigating two types of motor learning that may interact with each other and influence a crewmember's ability to re-adapt to Earth's gravity environment. In strategic learning, crewmembers make rapid modifications in their motor control strategy emphasizing error reduction. This type of learning may be critical during the first minutes and hours after landing. In adaptive learning, long-term plastic transformations occur, involving morphological changes and synaptic modification. In recent literature these two behavioral components have been associated with separate brain structures that control the execution of motor strategies: the strategic component was linked to the posterior parietal cortex and the adaptive component was linked to the cerebellum (Pisella, et al. 2004). The goal of this paper was to demonstrate the relative contributions of the strategic and adaptive components to the re-adaptation process in locomotor control after long duration space flight missions on the International Space Station (ISS). The Functional Mobility Test (FMT) was developed to assess crewmember s ability to ambulate postflight from an operational and functional perspective. Sixteen crewmembers were tested preflight (3 sessions) and postflight (days 1, 2, 4, 7, 25) following a long duration space flight (approx 6 months) on the ISS. We have further analyzed the FMT data to characterize strategic and adaptive components during the postflight readaptation period. Crewmembers walked at a preferred pace through an obstacle course set up on a base of 10 cm thick medium density foam (Sunmate Foam, Dynamic Systems, Inc., Leicester, NC). The 6.0m X 4.0m course consisted of several pylons made of foam; a Styrofoam barrier 46.0cm high that crewmembers stepped over; and a portal constructed of two Styrofoam blocks, each 31cm high, with a horizontal bar covered by foam and suspended from the ceiling which was adjusted to the height of the crewmember s shoulder. The portal required crewmembers to bend at the waist and step over a barrier simultaneously. All obstacles were lightweight, soft and easily knocked over. Crewmembers were instructed to walk through the course as quickly and as safely as possible without touching any of the objects on the course. This task was performed three times in the clockwise direction and three times in the counterclockwise direction that was randomly chosen. The dependent measures for each trial were: time to complete the course (seconds) and the number of obstacles touched or knocked down. For each crewmember, the time to complete each FMT trial from postflight days 1, 2, 4, 7 and 25 were further analyzed. A single logarithmic curve using a least squares calculation was fit through these data to produce a single comprehensive curve (macro). This macro curve composed of data spanning 25 days, illustrates the re-adaptive learning function over the longer time scale term. Additionally, logarithmic curves were fit to the 6 data trials within each individual post flight test day to produce 5 separate daily curves. These micro curves, produced from data obtained over the course of minutes, illustrates the strategic learning function exhibited over a relative shorter time scale. The macro curve for all subjects exhibited adaptive motor learning patterns over the 25 day period. Howev, 9/16 crewmembers exhibited significant strategic motor learning patterns in their micro curves, as defined by m > 1 in the equation of the line y=m*LN(x) +b. These data indicate that postflight recovery in locomotor function involves both strategic and adaptive mechanisms. Future countermeasures will be designed to enhance both recovery processes.

Warren, L. E.↗

Direct Imaging of the Structural and Morphological Evolution of Epitaxial LiCoO 2 Films during Charge and Overcharge

The capacity decay of layered cathodes in high-voltage applications underscores the need to utilize accurate and precise techniques to understand the underlying mechanisms. Here, we use well-defined epitaxial LiCoO 2 (LCO) films on SrRuO 3 /SrTiO 3 (SRO/STO) with controlled orientations and defect structures along with in situ electrochemical atomic force microscopy to probe the structural and morphological evolutions during the charge and overcharge processes. We quantitatively show the morphological changes in both the reversible delithiation regime and the irreversible over-delithiation regime and correlate the overall electrochemical behaviors to atomic scale defect evolutions in the films. Further, we also observe a significantly lower charging capacity for LCO/SRO/STO(111) compared to that of LCO/SRO/STO(001) films of the same thickness, which is ascribed to different types of atomic scale defects formed during the film growth process. Our high- resolution scanning transmission electron microscopy (STEM) and electron energy loss spectroscopy (EELS) studies reveal that the antiphase boundaries in LCO/SRO/STO(111) act as viable channels for Li migration but are more susceptible to irreversible phase transitions, which then block subsequent Li diffusion. The failure mechanisms developed here may provide insight into the design of future cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Explosive Soot Challenge (Final Report)

This project assembled a broad ensemble of modeling and experimentation tools to study the morphological and optical properties of detonation soots in explosive fireballs. A gram-scale hemispherical high explosive was studied in a low-pressure controlled environment using in-situ experimentation with diffusely illuminated visible absorption spectroscopy, particle sizing through light scattering techniques, and post-test collections with subsequent morphological analysis. Hydrocode modeling was performed to replicate the detonation flow observations, and subsequent aerosol kinetics models provided particle size distributions and extinction coefficients from the hydrocode results. Experimentally observed soot morphologies agreed with expectation from the literature - a bimodal distribution was found, brought upon by the particles growing to a size where their inertia and fluid wakes are non-negligible. The aerosol kinetics model did not replicate the observed bimodal size distribution for lack of a coagulation kernel to represent the behavior. To recover particulate optical properties, a spectrally resolved absorption spectroscopy method termed Spectral diffuse back-illuminated extinction imaging (SBI-EI) was developed and implemented on two explosive types. Inverting the absorption spectra using a Kramers-Kronig consistent method yielded the complex index of refraction for the soots produced by the explosives. This method resulted in an unrealistic index of refraction for one of the two explosives, and this is suspected to be due to the model neglecting scattering brought upon by the large particle sizes observed. In addition to the core work, three additional studies were performed in parallel. These investigated the impact of scattering on diffuse absorption spectroscopy, studied how soots oxidate and sublimate in a well-controlled shock tube, and laid the theoretical groundwork for a new collision kernel to replicate the bimodal size distribution from the observations. Summaries of these efforts are included at the end of this report.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Tailorable Micelle Morphology in Self-Assembling Block Copolymer Gels for Templating Nanoporous Ceramics

The self-assembly of block copolymers offers opportunities for the facile organization and templating of inorganic nanomaterials. Here, we describe a morphology map for a poly(methyl methacrylate)-b-poly(n-butyl acrylate)-b-poly(methyl methacrylate) (PMMA-b-PnBA-b-PMMA) block copolymer/polycarbosilane system that allows for tunable control over nanoscale micelle geometry via manipulation of the preceramic polymer content. We produced gels with spherical, wormlike, and bicontinuous morphologies, which were processed to create silicon carbide-based ceramic structures with tunable nanoscale porosities. The role of the constituent polymers in influencing the structure and rheology of this system is discussed. The PMMA-b-PnBA-b-PMMA block copolymer/preceramic polymer system offers a number of advantages including: (i) commercial availability, (ii) rapid self-assembly kinetics, and (iii) successful conversion of the self-assembled nanostructure to ceramic via pyrolysis. Finally, this system may be useful for catalytic, structural, or thermal applications in both industrial and academic settings because of its ease of use and relatively inexpensive reagents.

36 MATERIALS SCIENCE↗

Controlling Factors Analyses of Sediment Dispersal From Source-to-Sink Systems of Lacustrine Rift Basin: A Case Study From Paleogene Shahejie-Dongying Formations of Nanpu Sag, Eastern China

Tectonic activity not only shapes the basic stratigraphic framework of rift basins, but also profoundly affects the sediment dispersal in rift basins. In this study, analyses of heavy mineral assemblages in different periods demonstrate that there are three obvious tectono-sedimentary evolutionary stages (E s 3 –E s 2 , E s 1 –E d 2 , and E d 1 , respectively) in the Paleogene provenance area of Nanpu Sag, and the volume of sand bodies increases from the bottom of the Paleogene Shahejie (E s ) Formation to the top of the Dongying (E d ) Formation in Nanpu Sag. Besides, this study comprehensively utilize the analyses of seismic interpretation, palynology, heavy mineral, and borehole core samples to investigate the controlling factors of sediment dispersal in the rift basin. The assemblages of heavy minerals in different periods reflect the rock composition and catchment area of different provenance areas, and their vertical differences reflect the evolution process of the provenance area and reflect the uplift-denudation process of the provenance area. The results reveal that the synergy of the evolution of tectonic activity and the adjustment of topographical evolution are the main controlling factors of sediment dispersal in Nanpu Sag, while climate change is not the main controlling factor. We conclude that an increased sediment supply rate in the long term reflects the control of tectonic activity on basin topography, rather than climate fluctuations. The differences in morphological modification result in differential sediment dispersal, which is principally related to the differential extrusion of the fault system. The catchment area and provenance distance adjustment is evidenced by the vertical changes of heavy mineral characteristics of single-well and interaction and linkage of boundary faults, and the adjustment of topography evolution. A consideration is that the interaction and linkage of boundary faults and complex subsidence history are multi-directional, and differential evolution of provenance area is universal in lacustrine rift basins, all of this highlights the adjustment of sediment pathways generated by this characteristic of rift basins and emphasizes the importance of controlling factors analyses in understanding differential sediment dispersal that presents in the rift basins. Besides, four sets of sediment dispersal patterns were delineated based on different developmental regions in the rift basin, which are fault segmental point and multi-stage fault terrace, single-stage fault terrace and axial fault valley, axial fault terrace, and paleo-terrace and axial fault valley, respectively. This study has a certain guiding significance for the prediction of the spatial distribution of sand bodies in the rift basin and the exploration of potential oil and gas targets in the rift basin.

Yu, Jifeng↗

Automation of Nanoparticle Synthesis Processes in a Plasma Environment Using LabVIEW

This work presents an automated control system for the synthesis of nanomaterials by plasma-enhanced chemical vapor deposition (PECVD), implemented using the LabVIEW software environment. The main objective of the study is to develop an integrated hardware-software platform that enables sequential control of the key stages of the PECVD process, including vacuum chamber preparation, pressure monitoring, working gas supply, plasma ignition, power matching, cyclic nanomaterial growth, and optical monitoring of nanoparticles in the plasma environment. The use of LabVIEW made it possible to integrate actuator control, experimental parameter acquisition, and realtime process visualization within a single automated system. The automated cycle begins with evacuation of the reaction chamber to a predefined base pressure. Transition to the next stage is permitted only after the specified pressure threshold has been reached, ensuring reproducible initial conditions for each experiment. The program then controls the supply of the working gas through mass flow controllers (MFCs). In this work, two gas-flow control modes were considered: analog control using a 0-5 V voltage signal and digital communication via RS-232 interface. It was shown that the analog approach requires accurate scaling of the control voltage, since applying 5 V corresponds to full-scale opening of the controller and results in the maximum gas flow. In contrast, the RS232 interface enables the gas flow rate to be specified directly in sccm, improving the accuracy, flexibility, and convenience of gas-environment control. After pressure stabilization, LabVIEW initiates RF plasma ignition and executes the RF matching algorithm aimed at minimizing reflected power and improving the stability of the plasma process. A separate software module implements the cyclic nanomaterial growth mode, in which the plasma-on time, plasma duration, and total number of synthesis cycles are predefined. This approach makes it possible to control material accumulation on the substrate and to correlate the process parameters with the morphological characteristics of the resulting nanostructures. The final module of the system is designed for optical monitoring of the nanoparticle cloud density in dusty plasma. For this purpose, the change in the intensity of laser radiation passing through the plasma region is recorded using a photodetector and a Keithley 2401 measuring unit connected to LabVIEW via RS-232 interface. The difference between the initial and modified optical signal intensity is used as a diagnostic parameter characterizing the formation and temporal evolution of nanoparticles. The developed system demonstrates that LabVIEW can be effectively applied not only for the automation of individual instruments, but also for the implementation of a complete digital control cycle for PECVD-based nanomaterial synthesis.

PECVD↗

Coupled morphological and convective instabilities in a microgravity environment

The role of convection during crystal growth from the melt is discussed in terms of dimensionless groups of material parameters and control variables. The limitations of such analyses and of models in which the crystal-melt interface is treated as a rigid boundary are reviewed. The interaction of thermosolutal convective instabilities with morphological instabilities is discussed for unidirectional solidification, emphasizing suppression of convective instabilities in a microgravity environment and/or a static magnetic field.

Sekerka, R. F.↗

Unveiling Morphology and Crystallinity Dynamics in Ni x Mn 1– x CO 3 Cathode Precursors through Batch-Mode Coprecipitation

This study delves into the synthesis and control of Ni x Mn 1–x CO 3 , a critical class of Mn-rich, Co-free precursors vital for cathode-oxide materials in energy storage and conversion technologies. Employing batch-mode coprecipitation, we systematically generated samples with varying Ni concentrations (x = 0, 0.1, 0.3, 0.5, 0.7, and 0.9) and conducted a comprehensive analysis of their compositions, crystallinities, transition-metal distributions, and particle morphologies through both experimental and computational methods. A significant variation in particle size and crystallinity was observed, contingent on the Ni content. Further, a pivotal transition emerged at Ni concentrations above x = ~0.5, transforming uniform morphologies, such as spherical, monodisperse, pseudo-single-crystalline particles, into bimodal, polycrystalline structures. Furthermore, the study highlights the role of Ni–ammonia complexes leading to Ni-deficient precipitates and underscores the importance of ammonia concentration in achieving precise Ni content control. This study unveils critical reaction conditions governing Mn-rich precursor properties that are vital for cathode-oxides, emphasizing the need for meticulous synthetic control and offering the potential for practical applications in advanced energy storage and conversion systems.

25 ENERGY STORAGE↗

A combination interferometric and morphological image processing approach to rapid quality assessment of additively manufactured cellular truss core components

Advanced manufacturing (AM) processes such as laser powder bed fusion (LPBF) are increasingly capable of fabricating components with useful and unprecedented mechanical properties by incorporating complex internal bracing structures. From the standpoint of quality control and assessment, however, internally complex assemblies present significant build-verification challenges. Here we propose a hybrid approach to the inspection involving the application of computer-aided speckle interferometry (CASI) and morphological image processing as a rapid, inexpensive, and facile method for AM quality control. The described methodology has low capital equipment costs, is full-field and non-contact, can be used in an industrial setting, and has very low requirements in terms of operator training and expertise. Consisting primarily of the combination of image processing software with a simple optical system of variable sensitivity, the method is shown to be effective for inspection of a titanium honeycomb component subjected to differential pressure. Results are compared to those achieved with computed tomography (CT), immersion ultrasound testing (UT), and optical holographic interferometry. Here we propose several possible processing strategies for automated quality assessment based on this powerful hybrid approach.

36 MATERIALS SCIENCE↗

Planetary geological studies

A global data base was assembled for the study of Mars crater ejecta morphology. The craters were classified as to morhology using individual photographic prints of Viking orbiter frames. Positional and scale information were derived by fitting digitized mosaic coordinates to lattitude-longitude coordinates of surface features from the Mars geodetic control net and feature coordinates from the U.S.G.S. series of 1:5,00,000 scale shaded relief maps. Crater morphology characteristics recorded are of two classes - attributes of each ejecta deposit and other crater charactersitics. Preliminary efforts to check the data base with findings of other workers are described.

Blasius, K. R.↗

Focused Electron Beam-Based 3D Nanoprinting for Scanning Probe Microscopy: A Review

Scanning probe microscopy (SPM) has become an essential surface characterization technique in research and development. By concept, SPM performance crucially depends on the quality of the nano-probe element, in particular, the apex radius. Now, with the development of advanced SPM modes beyond morphology mapping, new challenges have emerged regarding the design, morphology, function, and reliability of nano-probes. To tackle these challenges, versatile fabrication methods for precise nano-fabrication are needed. Aside from well-established technologies for SPM nano-probe fabrication, focused electron beam-induced deposition (FEBID) has become increasingly relevant in recent years, with the demonstration of controlled 3D nanoscale deposition and tailored deposit chemistry. Moreover, FEBID is compatible with practically any given surface morphology. In this review article, we introduce the technology, with a focus on the most relevant demands (shapes, feature size, materials and functionalities, substrate demands, and scalability), discuss the opportunities and challenges, and rationalize how those can be useful for advanced SPM applications. As will be shown, FEBID is an ideal tool for fabrication/modification and rapid prototyping of SPM-tipswith the potential to scale up industrially relevant manufacturing.

36 MATERIALS SCIENCE↗

Precision Control of Thermal Transport in Cryogenic Single-Crystal Silicon Devices

We report on the diffusive-ballistic thermal conductance of multi-moded single-crystal silicon beams measured below 1 K. It is shown that the phonon mean-free-path is a strong function of the surface roughness characteristics of the beams. This effect is enhanced in diffuse beams with lengths much larger than, even when the surface is fairly smooth, 510 nm rms, and the peak thermal wavelength is 0.6 microns. Resonant phonon scattering has been observed in beams with a pitted surface morphology and characteristic pit depth of 30 nm. Hence, if the surface roughness is not adequately controlled, the thermal conductance can vary significantly for diffuse beams fabricated across a wafer. In contrast, when the beam length is of order, the conductance is dominated by ballistic transport and is effectively set by the beam cross-sectional area. We have demonstrated a uniformity of +/-8% in fractional deviation for ballistic beams, and this deviation is largely set by the thermal conductance of diffuse beams that support the micro-electro-mechanical device and electrical leads. In addition, we have found no evidence for excess specific heat in single-crystal silicon membranes. This allows for the precise control of the device heat capacity with normal metal films. We discuss the results in the context of the design and fabrication of large-format arrays of far-infrared and millimeter wavelength cryogenic detectors.

multi-moded single-crystal silicon beams↗

Dynamic Motions of Topological Defects in Nematic Liquid Crystals under Spatial Confinement

Abstract Topological defects (TDs) have become a sensational topic due to their significant influence on the unusual optical and physiochemical characteristics of the material. To facilitate their application across a wide range of disciplines it is desirable to analyze and gain fundamental understanding of TDs in both equilibrium and nonequilibrium systems. Liquid crystals (LCs) are considered an ideal system for study given the direct visualization of TDs and a straightforward analyzation process. In addition to the equilibrium morphology of LC TDs, it is also of great interest to track and control the formation and annihilation of defects during thermodynamic processes. However, controlling the dynamic behavior of formed defects remains a challenge. Here, nematic LCs confined in a cell exhibiting surfaces with periodic anchoring conditions containing surface topography are relied on. The effects of patterned surface characteristics such as width, periodicity, and degree of curvature on defects dynamic motion, stabilization, and annihilation are explored. The computational experiments recapitulate the TDs transition path and provide free energy‐based predictions of critical distances for defect annihilation. Taken together, this simple approach offers a promising opportunity to control the dynamics of TDs in LCs through chemical patterned surfaces with topography.

36 MATERIALS SCIENCE↗

Advancing the Performance of Lithium-Rich Oxides in Concert with Inherent Complexities: Domain-Selective Substitutions

Historically, modifications to Li- and Mn-rich (LMR) cathodes have been studied in relation to their efficacy in solving challenges such as oxygen loss and voltage fade, which are inherent to the activation process of these electrodes. However, even in the presence of these phenomena, well-optimized LMR cathodes show considerable promise as earth-abundant options, particularly if other barriers to implementation can be overcome or mitigated. As the complex mechanisms of LMR electrodes are known to stem from the local, chemical inhomogeneities that define the nanocomposite domain nature of these oxides, strategies aimed at manipulating the performance of activated electrodes, irrespective of voltage fade, through domain-selective modifications, could prove instructive. In this work, we use a novel synthesis process aimed at influencing the site occupancy of substituted Sn 4+ , as an example 4+ cation, into a Co-free Li 1.13 Mn 0.57(1–x) Sn 0.57x Ni 0.3 O 2 LMR oxide. We show that Sn 4+ can be selectively substituted into Li-rich environments. The consequences are revealed to be both chemical and morphological, and the domain-selective doping strategy provides a knob for directed control of the low state-of-charge impedance behavior. In conclusion, these results reveal new clues and insights with respect to further advancing the practical relevance of LMR cathode particles and electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrobiogeochemical Controls on the Delivery of Dissolved Organic Matter to Boreal Headwater Streams

Understanding controls on the delivery of dissolved organic matter (DOM) from terrestrial to aquatic systems is key for constraining carbon balances and fluxes in boreal headwater catchments. The largest export of DOM generally occurs during intense periods of water delivery to the landscape (e.g., rain events); however, the timing and magnitude of DOM is complicated by geomorphological, hydrometeorological, and biogeochemical variability. To better assess mechanisms controlling the delivery of DOM to boreal streams, DOM was investigated in two morphologically distinct catchments of an experimental forest watershed in western Newfoundland, one dominated by low relief wetlands and the other by steep hillslopes. The DOM was compared during two fall storms of similar magnitude but contrasting moisture conditions during the autumn transition. Variable concentrations and optical character highlighted antecedent conditions are important for the delivery of DOM to boreal streams. Concentration-discharge relationships with stream hydrograph separation analysis suggest preferential flowpaths through shallow mineral horizons as a key pathway for delivery of DOM in the hillslope dominated catchment compared to rapid input from near-stream wetlands in the low relief catchment. Loss of DOM via preferential pathways suggests an additional mechanism for surface soil carbon loss not directly informed by lateral flow and soil hydrology, which has important implications for our conceptualization and modeling of carbon fluxes in boreal systems. These results suggest watershed scale responses of DOM in boreal headwater catchments are complex, and better linkages between catchment scale hydrology and landscape hydrobiogeochemistry are required to constrain terrestrial to aquatic carbon fluxes in boreal landscapes.

54 ENVIRONMENTAL SCIENCES↗

Evolution of micro-pores in Ni–Cr alloys via molten salt dealloying

Porous materials with high specific surface area, high porosity, and high electrical conductivity are promising materials for functional applications, including catalysis, sensing, and energy storage. Molten salt dealloying was recently demonstrated in microwires as an alternative method to fabricate porous structures. The method takes advantage of the selective dissolution process introduced by impurities often observed in molten salt corrosion. This work further investigates molten salt dealloying in bulk Ni–20Cr alloy in both KCl–MgCl 2 and KCl–NaCl salts at 700 °C, using scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction (XRD), as well as synchrotron X-ray nano-tomography. Micro-sized pores with irregular shapes and sizes ranging from sub-micron to several microns and ligaments formed during the process, while the molten salt dealloying was found to progress several microns into the bulk materials within 1–16 h, a relatively short reaction time, enhancing the practicality of using the method for synthesis. The ligament size increased from ~ 0.7 μm to ~ 1.3 μm in KCl–MgCl 2 from 1 to 16 h due to coarsening, while remaining ~ 0.4 μm in KCl–NaCl during 16 h of exposure. The XRD analysis shows that the corrosion occurred primarily near the surface of the bulk sample, and Cr 2 O 3 was identified as a corrosion product when the reaction was conducted in an air environment (controlled amount sealed in capillaries); thus surface oxides are likely to slow the morphological coarsening rate by hindering the surface diffusion in the dealloyed structure. 3D-connected pores and grain boundary corrosion were visualized by synchrotron X-ray nano-tomography. This study provides insights into the morphological and chemical evolution of molten salt dealloying in bulk materials, with a connection to molten salt corrosion concerns in the design of next-generation nuclear and solar energy power plants.

36 MATERIALS SCIENCE↗