Search NASA⌕ Search

SEARCH · Search NASA

Results for “PHASE VELOCITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Hot gas ingestion characteristics and flow visualization of a vectored thrust STOVL concept

A 9.2 percent scale short takeoff and vertical landing (STOVL) hot gas ingestion model was designed and built by McDonnell Douglas Corporation (MCAIR) and tested in the NASA Lewis Research Center 9- by 15-Foot Low Speed Wind Tunnel (LSWT). Hot gas ingestion, the entrainment of heated engine exhaust into the inlet flow field, is a key development issue for advanced short takeoff and vertical landing aircraft. The Phase 1 test program, conducted by NASA Lewis and McDonnell Douglas Corporation, evaluated the hot ingestion phenomena and control techniques and Phase 2 test program which was conducted by NASA Lewis are both reported. The Phase 2 program was conducted at exhaust nozzles temperatures up to 1460 R and utilized a sheet laser system for flow visualization of the model flow field in and out of ground effects. Hot gas ingestion levels were measured for the several forward nozzle splay configurations and with flow control/lift improvement devices which reduced the hot gas ingestion. The model support system had four degrees of freedom, heated high pressure air for nozzle flow, and a suction system exhaust for inlet flow. The headwind (freestream) velocity for Phase 1 was varied from 8 to 90 kn, with primary data taken in the 8 to 23 kn headwind velocity range. Phase 2 headwind velocity varied from 10 to 23 kn. Results of both Phase 1 and 2 are presented. A description of the model, facility, a new model support system, and a sheet laser illumination system are also provided. Results are presented over a range of main landing gear height (model height) above the ground plane at a 10 kn headwind velocity. The results contain the compressor face pressure and temperature distortions, total pressure recovery, compressor face temperature rise, and the environmental effects of the hot gas. The environmental effects include the ground plane temperature and pressure distributions, model airframe heating, and the location of the ground flow separation. Results from the sheet laser flow visualization test are also shown.

Johns, Albert L.↗
NASA NTRS2007

Experimental Evaluation of an Isolated Synthetic Jet IN Crossflow

The second case for this workshop builds upon the isolated synthetic jet of Case 1 by adding a crossflow, with no streamwise pressure gradient, for the developing jet to interact with. Formally, Case 2 examines the interaction of a single, isolated, synthetic jet and a fully turbulent zero-pressure gradient boundary layer. The resulting flow has many of the characteristics that need to be modeled with fidelity if the results of the calculations are to serve as the basis for research and design with active flow control devices. These include the turbulence in the boundary layer, the time-evolution of the large vortical structure emanating from the jet orifice and its subsequent interaction with and distortion by the boundary layer turbulence, and the effect of the suction cycle on the boundary layer flow. In a synthetic jet, the flow through the orifice and out into the outer flowfield alternates between an exhaust and a suction cycle, driven by the contraction and expansion of a cavity internal to the actuator. In the present experiment, the volume changes in the internal cavity are accomplished by replacing one of the rigid walls of the cavity, the wall opposite the orifice exit, with a deformable wall. This flexible wall is driven by a bottom-mounted moveable piston. The piston is driven electro-mechanically. The synthetic jet issues into the external flow through a circular orifice. In the present experiment, this orifice has a diameter of 0.250 inches (6.35 mm). The flow is conceptually similar to that documented in Schaeffler [1]. To document the flow, several measurement techniques were utilized. The upstream boundary conditions (in-flow conditions), and several key phase-averaged velocity profiles were measured with a 3-component laser-Doppler velocimetry system. Phase-averaged velocity field measurements were made with both stereo digital particle image velocimetry and 2-D digital particle image velocimetry as the primary measurement system. Surface pressure measurements were made utilizing an electronically scanned pressure system.

Schaeffler, Norman W.↗
DOE OSTI2018

Complementary Probes of Dark Energy using Galaxy Clusters

Here, we have built a framework to constrain Dark Energy (DE) using the spatial distributions, number counts, and escape velocities of galaxy clusters in the context of next generation spectroscopic surveys. In the ΛCDM paradigm, galaxy clusters trace the expansion of the Universe in three different ways. (1.) Spatial distribution:The baryon acoustic oscillations (BAO) formed during recombination are imprinted into the spatial distribution of clusters. The locations of the BAO are standard-rulers which map the length-scale of the sound horizon. Statistical measures like the two-point correlation function and the power spectrum can be used to trace the scale of the BAO and thus the expansion history of the Universe.(2.) Number counts: Galaxy clusters are identified as peaks above a threshold in the underlying matter density field. Galaxies attract onto these peaks over time until gravity loses the battle against the accelerating expansion of space. The number and mass of galaxy clusters over time is sensitive to the strength of the DE and the amount of matter in the Universe.(3.) Escape velocity:The radius-velocity phase-space of galaxies within clusters has a sharp edge which traces the escape velocity of galaxies. This escape velocity is a combination of the local Newtonian gravitational potential and the acceleration of the expansion of the Universe. Weak lensing mass profiles of clusters can be used to predict the escape velocity profile from just the gravitational Newtonian component. In an expanding or contracting Universe, the observed phase-space escape velocity surface would be modified from this prediction.We built the large-scale structure covariances from mock catalogs which we can now use in the likelihood analyses to constrain Dark Energy models. We have developed the analytical framework to conduct the joint likelihood analysis of the bias function and the abundance function in order to constrain DE through their redshift evolution.We have investigated a new Dark Energy test that uses the weak lensing prediction of the grav-itational potential compared to the observed escape velocity profile from galaxy clusters. We have made predictions on the improvement in the Dark Energy figure-of-merit from this new test. We have also investigated the predicted enhancements of the cluster escape velocity profiles from modifi-cations to gravity. This effort can help rule out model classes of modified gravity as alternatives to Dark Energy.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

Maximal energy extraction under discrete diffusive exchange

Waves propagating through a bounded plasma can rearrange the densities of states in the six-dimensional velocity-configuration phase space. Depending on the rearrangement, the wave energy can either increase or decrease, with the difference taken up by the total plasma energy. In the case where the rearrangement is diffusive, only certain plasma states can be reached. It turns out that the set of reachable states through such diffusive rearrangements has been described in very different contexts. Building upon those descriptions, and making use of the fact that the plasma energy is a linear functional of the state densities, the maximal extractable energy under diffusive rearrangement can then be addressed through linear programming.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

Stereoscopy of dust density waves under microgravity: Velocity distributions and phase-resolved single-particle analysis

Experiments on dust-density waves have been performed in dusty plasmas under the microgravity conditions of parabolic flights. Three-dimensional measurements of a dust density wave on a single particle level are presented. The dust particles have been tracked for many oscillation periods. A Hilbert analysis is applied to obtain trajectory parameters such as oscillation amplitude and three-dimensional velocity amplitude. While the transverse motion is found to be thermal, the velocity distribution in wave propagation direction can be explained by harmonic oscillations with added Gaussian (thermal) noise. Additionally, it is shown that the wave properties can be reconstructed by means of a pseudo-stroboscopic approach. Finally, the energy dissipation mechanism from the kinetic oscillation energy to thermal motion is discussed and presented using phase-resolved analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1988

Effects of excitation level on the stability of an axisymmetric mixing layer

The effect of various levels of excitation on the stability and development of an axisymmetric mixing layer was studied experimentally. The flow was excited axisymmetrically by a single speaker placed at the base of the plenum chamber. Measurements of mean and phase-averaged velocity profiles were made using an array of hot-wire probes. The measured profiles were compared to eigenfunctions calculated from linear, viscous stability theory. It is shown that the theoretical predictions, based on measured profiles of mean velocity, compare very well with the phase-averaged measurements, even when the local disturbance reaches levels as high as 24 percent of the jet speed. The cumulative effect of excitation on the mean flow is examined as a function of local Strouhal number as well as excitation level.

Samet, M. M.↗
NASA NTRS1976

Vibratory hub load data reduction and analysis from the reverse velocity rotor wind tunnel test, phase 2B

The vibratory hub loads data analysis from the reverse velocity rotor wind tunnel test is reported. Vibratory loads were obtained from the rotating hub balance and also by synthesis of generalized coordinates from the blade flap bending moments. Load trends were defined as a function of speed, rotor thrust and 2 per rev cyclic from each of the data methods. These trends were compared to determine the degree of agreement between each method and provide substantiation for the generalized coordinate approach.

Taylor, R. B.↗
NASA NTRS1999

Buoyancy Driven Shear Flows of Bubble Suspensions

In this work the gas volume fraction and the root-mean-squared fluid velocity are measured in buoyancy driven shear flows of bubble suspensions in a tall, inclined, rectangular channel. The experiments are performed under conditions where We << 1a nd Re >> 1, for which comparisons are made with kinetic theory and numerical simulations. Here Re = gamma(a(exp 2)/nu is the Reynolds number and We = rho(gamma(exp 2))a(exp 3)/sigma is the Weber number; gamma is the shear rate, a is the bubble radius, nu is the kinematic viscosity of the liquid, rho is the density of the liquid, and sigma is the surface tension of the gas/liquid interface. Kang et al. calculated the bubble phase pressure and velocity variance of sheared bubble suspensions under conditions where the bubbles are spherical and the liquid phase velocity field can be approximated using potential flow theory, i.e. We= 0 and Re >> 1. Such conditions can be achieved in an experiment using gas bubbles, with a radius of O(0.5mm), in water. The theory requires that there be no average relative motion of the gas and liquid phases, hence the motivation for an experimental program in microgravity. The necessity of performing preliminary, Earth based experiments, however, requires performing experiments where the gas phase rises in the liquid, which significantly complicates the comparison of experiments with theory. Rather than comparing experimental results with theory for a uniform, homogeneous shear flow, experiments can be compared directly with solutions of the averaged equations of motion for bubble suspensions. This requires accounting for the significant lift force acting on the gas phase when the bubbles rise parallel to the average velocity of the sheared suspension. Shear flows can be produced in which the bubble phase pressure gradient, arising from shear induced collisions amongst the bubbles, balances a body force (centrifugal or gravitational) on the gas phase. A steady, non-uniform gas volume fraction can be measured, from which the bubble phase pressure gradient can be obtained and compared to theory and numerical simulations. The presence of bounding walls further complicates the experiments, since the detailed interactions of the bubbles with bounding walls is not well understood, especially in the presence of gravity, where the momentum and energy exchange depends on the inclination of the wall.

Koch, D. L.↗
DOE OSTI2017

Chorus Waves Modulation of Langmuir Waves in the Radiation Belts

Using high-resolution waveforms measured by the Van Allen Probes, we report a novel observation in the radiation belts. Namely, we show that multiband, discrete, rising-tone whistler-mode chorus emissions exhibit a one-to-one correlation with Langmuir wave bursts. Moreover, the periodic Langmuir wave bursts are generally observed at the phase location where the chorus wave E || component is oriented opposite to its propagation direction. The electron measurements show a beam in phase space density at the particle velocity that matches the parallel phase velocity of the chorus waves. Based on this evidence, we conclude that the chorus waves accelerate the suprathermal electrons via Landau resonance, and generate a localized electron beam in phase space density. Consequently, the Langmuir waves are excited locally and are modulated by the chorus wave phase. As a result, this microscale interaction between chorus waves and high frequency electrostatic waves provides a new insight into the nonlinear wave-particle interaction process.

58 GEOSCIENCES↗
NASA NTRS2012

Reconfigurable Wave Velocity Transmission Lines for Phased Arrays

This presentation discussed a novel phased array with an emphasis to simplify the array feed. Specifically, we will demonstrate a simple, low cost feeding approach by mechanically controlling the substrate thickness. The array feed lines are constructed from parallel plate transmission lines whose thickness are adjusted to control their effective dielectric constant (Epsilon_eff). As a result the phase delay/excitation at each array element will be adjusted per desired beam direction. The proposed antenna elements will be overlapping dipoles operating over a 2:1 bandwidth in the Ku-Band spectrum. Preliminary simulation and experimental demonstration of such an array will be presented.

Host, Nicholas Keith↗
DOE OSTI2015

The silicon and calcium high-velocity features in type Ia supernovae from early to maximum phases

The high-velocity features (HVFs) in optical spectra of type Ia supernovae (SNe Ia) are examined with a large sample including very early-time spectra (e.g., t < −7 days). Multiple Gaussian fits are applied to examine the HVFs and their evolutions, using constraints on expansion velocities for the same species (i.e., Si ii 5972 and Si ii 6355). We find that strong HVFs tend to appear in SNe Ia with smaller decline rates (e.g., Δm{sub 15}(B) ≲ 1.4 mag), clarifying that the finding by Childress et al. for the Ca-HVFs in near-maximum-light spectra applies both to the Si-HVFs and Ca-HVFs in the earlier phase. The Si-HVFs seem to be more common in rapidly expanding SNe Ia, which is different from the earlier result that Ca-HVFs are associated with SNe Ia that have slower Si ii 6355 velocities at maximum light (i.e., V{sup Si}{sub max}). Moreover, SNe Ia with both stronger HVFs at early phases and larger V{sup Si}{sub max} are found to have noticeably redder B−V colors and to occur preferentially in the inner regions of their host galaxies, while those with stronger HVFs but smaller V{sup Si}{sub max} show opposite tendencies, suggesting that these two subclasses have different explosion environments and their HVFs may have different origins. We further examine the relationships between the absorption features of Si ii 6355 and Ca ii IR lines, and find that their photospheric components are well correlated in velocity and strength but that the corresponding HVFs show larger scatter. These results cannot be explained with ionization and/or thermal processes alone, and different mechanisms are required for the creation of HVF-forming regions in SNe Ia.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1988

On the preferred mode of jet instability

The preferred mode of instability was investigated in an axisymmetric air jet of moderate Reynolds number. Natural instabilities are shown to scale with local shear-layer thickness and the preferred mode is shown to be a shear-layer instability. The spatial evolution of the preferred mode was examined by exciting the flow acoustically and then mapping the phase-locked velocity fluctuations. Throughout the potential core region the phase-locked profiles are shown to agree with the eigensolutions of the Orr-Sommerfeld stability equations provided the calculations are based on measured, mean velocity profiles. The excitation intensity was varied from low levels, where the flow was merely tagged, to high levels where the mean flow was substantially distorted, and over that range of excitation there was no apparent deterioration in the agreement with stability predictions.

Petersen, R. A.↗
NASA NTRS1985

Enhanced ion outflows measured by the DE 1 high altitude plasma instrument in the dayside plasmasphere during the recovery phase

Ion flow velocities both parallel and perpendicular to the magnetic field, and including the effects of spacecraft charging and spacecraft velocity, have been measured during the recovery phase of two large magnetic storms on October 14 and 21 of 1981. These measurements were made both inside and outside the plasmasphere and indicate unreported yet substantial outflows of ions within the dayside plasmasphere (October 14). Combined data from instruments on board the Dynamics Explorer satellite, including the high altitude plasma instrument, the energetic ion composition spectrometer, the retarding ion mass spectrometer, and the plasma wave instrument, indicate that these ions are most likely dominantly O(+) at energies at least as low as 5 eV. The nightside pass (October 21), which occurred during the recovery phase of a similar storm, showed no plasmaspheric outflows. The results indicate that a large contribution to the outflux into the dayside plasmasphere during the recovery period is due to E greater than 5 eV ions.

Menietti, J. D.↗
DOE OSTI2014

An approach to improving transporting velocity in the long-range ultrasonic transportation of micro-particles

In existing ultrasonic transportation methods, the long-range transportation of micro-particles is always realized in step-by-step way. Due to the substantial decrease of the driving force in each step, the transportation is lower-speed and stair-stepping. To improve the transporting velocity, a non-stepping ultrasonic transportation approach is proposed. By quantitatively analyzing the acoustic potential well, an optimal region is defined as the position, where the largest driving force is provided under the condition that the driving force is simultaneously the major component of an acoustic radiation force. To keep the micro-particle trapped in the optimal region during the whole transportation process, an approach of optimizing the phase-shifting velocity and phase-shifting step is adopted. Due to the stable and large driving force, the displacement of the micro-particle is an approximately linear function of time, instead of a stair-stepping function of time as in the existing step-by-step methods. An experimental setup is also developed to validate this approach. Long-range ultrasonic transportations of zirconium beads with high transporting velocity were realized. The experimental results demonstrated that this approach is an effective way to improve transporting velocity in the long-range ultrasonic transportation of micro-particles.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Collective modes in excitonic insulators: Effects of electron-phonon coupling and signatures in the optical response

Here, we consider a two-band spinless model describing an excitonic insulator (EI) on the two-dimensional square lattice with anisotropic hopping parameters and electron-phonon (el-ph) coupling, inspired by the EI candidate Ta 2 NiSe 5 . We systematically study the nature of the collective excitations in the ordered phase which originates from the interband Coulomb interaction and the el-ph coupling. When the ordered phase is stabilized only by the Coulomb interaction (pure EI phase), its collective response exhibits a massless phase mode in addition to the amplitude mode. We show that in the BEC regime, the signal of the amplitude mode becomes less prominent and that the anisotropy in the phase-mode velocities is reduced. Through coupling to the lattice, the phase mode acquires a mass and the signal of the amplitude mode becomes less prominent. Importantly, the character of the softening mode at the boundary between the normal semiconductor phase and the ordered phase depends on the parameters. In particular, we point out that even for el-ph coupling smaller than the Coulomb interaction, the mode that softens to zero at the boundary can have a phonon character. We also discuss how the collective modes can be observed in the optical conductivity. Furthermore, we study the effects of nonlocal interactions on the collective modes and show the possibility of realizing a coexistence of an in-gap mode and an above-gap mode split off from the single-amplitude mode in the system with local interactions only.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Computational Analysis of the Impact of Boundary Conditions on a Particle-Laden Flow: A Case Study in a Pressurized Oxy-Coal Combustor

Designing an effective burner is vital for the development of coal combustion technologies. Because of high pressure, the volumetric fraction of the coal particles in the injected fuel in a pressurized oxy-combustion (POC) burner approaches or even exceeds the limitations allowed by the commercial computational fluid dynamics codes (e.g., Ansys Fluent). Consequently, for such high particle volumetric fractions, the interplay between the particles, the fluid flow, and the burner wall needs to be re-evaluated. The present computational work is a first step in a systematic analysis of the roles of various characteristics involved in the POC process, such as the method of particle release, its location, and the particle size. Specifically, pulverized coal is burned under an elevated pressure of 15 bar in an O 2 /CO 2 environment. A 100 kW, a POC combustor, is modeled with Ansys Fluent using the Reynolds-averaged Navier−Stokes approach. It is revealed that for this pilot-scale, pressurized burner, the gas phase flow velocity in the near-wall region exhibits anomalies. With the major focus on POC, this work aims to eliminate/reduce the impact of high particle loading on the gas-phase flow. To scrutinize the role of particle loading in the near-wall region and eliminate the impact of this velocity on POC downstream, the particle−gas interplay in the boundary layer is investigated by means of the computational simulations incorporating the coupling between the turbulent flow and the particles. It is found that the tuning of the particle release location makes the gas-phase flow velocity in the presence of particles consistent with the pure gas flow velocity profile. The particles size is also found to have a significant impact on the particle trajectory.

CFD↗