Search NASA⌕ Search

SEARCH · Search NASA

Results for “Panelized”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Investigation of the reactions of skin panels in relation to duration of acoustical loading

Certain characteristics of the reactions of typical skin panels of a passenger aircraft to acoustical loading are being investigated, for development of an objective method of diagnostics for skin condition, under the operations and maintenance sections of civil aviation. There are a number of difficulties connected with the solution of this problem. The reactions of skin panels exposed to the noises of the exhaust jets are dependent on the aircraft operating conditions, the geometric parameters and limiting conditions of the panels.

Kvitka, V. Y.↗
NASA NTRS1974

Thermal-Structural Evaluation of TD Ni-20Cr Thermal Protection System Panels

The results of a thermal-structural test program to verify the performance of a metallic/radiative Thermal Protection System (TPS) under reentry conditions are presented. This TPS panel is suitable for multiple reentry, high L/D space vehicles, such as the NASA space shuttle, having surface temperatures up to 1200 C (2200 F). The TPS panel tested consists of a corrugation-stiffened, beaded-skin TD Ni-20Cr metallic heat shield backed by a flexible fibrous quartz and radiative shield insulative system. Test conditions simulated the critical heating and aerodynamic pressure environments expected during 100 repeated missions of a reentry vehicle. Temperatures were measured during each reentry cycle; heat-shield flatness surveys to measure permanent set of the metallic components were made every 10 cycles. The TPS panel, in spite of localized surface failures, performed its designated function.

Eidinoff, H. L.↗
NASA NTRS1974

Techniques for aerothermal tests of large, flightweight thermal protection panels in a Mach 7 wind tunnel

Recently developed experimental techniques permit evaluating thermal performance and structural integrity of full-scale panel concepts applicable to reentry and hypersonic vehicles in the Langley 8-foot high-performance structures tunnel. Rate and magnitude of surface heating and differential-pressure loading are independently controlled. Realistic temperature distributions are radiantly preheated into the panel prior to aerodynamic heating, and stream conditions are preselected to sustain the preheat surface heating input during aerodynamic exposure. During tunnel start and shutdown, panels are shielded outside the stream from potentially damaging transient acoustics and buffeting and are then rapidly inserted into the hypersonic flow. Infrared radiometry provides detailed surveys of surface temperatures.

Deveikis, W. D.↗
NASA NTRS1974

Advanced beaded and tubular structural panels. Volume 1: Design and analysis

A study was conducted to exploit the efficiency of curved elements in the design of lightweight structural panels under combined loads of axial compression, inplane shear, and bending. Data cover analytical procedures for optimum panel design, static strength analyses, results of panel design studies, and correlation of theory with test results.

Greene, B. E.↗
NASA NTRS1974

Substantiation Data for Advanced Beaded and Tubular Structural Panels. Volume 3: Testing

The test program is described, which was conducted to provide the necessary experimental data to verify the design and analysis methods developed for beaded and tubular panels. Test results are summarized and presented for all local buckling and full size panel tests. Selected representative test data from each of these tests is presented in detail. The results of this program established a valid analysis and design procedure for circular tube panels. Test results from three other configurations show deformational modes which are not adequately accounted for in the present analyses.

Hedges, P. C.↗
NASA NTRS1974

Advanced beaded and tubular structural panels. Volume 2: Fabrication

A study was conducted to exploit the efficiency of curved elements in the design of lightweight structural panels under combined loads of axial compression, inplane shear, and bending. A summary of the total program (analysis, fabrication and test) is presented in document NASA CR-2514. Detailed descriptions of the analysis effort and of the panel tests are contained in supplementary documents NASA CR-132460 and NASA-CR-132515 respectively. Data are also given on the development of economical fabrication techniques to minimize the effects of fabrication limitations on optimum panel designs.

Musgrove, M. D.↗
NASA NTRS1975

On an integro-differential equation model for the study of the response of an acoustically coupled panel

The response of a clamped panel to supersonically convected turbulence is considered. A theoretical model in the form of an integro-differential equation is employed that takes into account the coupling between the panel motion and the surrounding acoustic medium. The kernels of the integrals, which represent induced pressures due to the panel motion, are Green's functions for sound radiations under various moving and stationary sources. An approximate analysis is made by following a finite-element Ritz-Galerkin procedure. Preliminary numerical results, in agreement with experimental findings, indicate that the acoustic damping is the controlling mechanism of the response.

Yen, D. H. Y.↗
NASA NTRS1976

The ACT transport: Panacea for the 80's or designer's illusion (panel discussion)

A panel discussion was held which attempted to make an objective and pragmatic assessment of the standing of active control technology. The discussion focused on the standing of active control technology relative to civil air transport applications, the value as opposed to the cost of the projected benefits, the need for research, development, and demonstration, the role of government and industry in developing the technology, the major obstacles to its implementation, and the probable timing of the full utilization of active control technology in commercial transportation. An edited transcription of the prepared statements of the panel members and the subsequent open discussion between the panel and the audience is presented.

Source record↗
NASA NTRS1976

Analysis of panel dent resistance

An analytical technique for elastic-plastic deformation of panels was developed, which is employed to analyze the denting mechanisms of panels resulting from point projectile impacts and impulsive loadings. The correlations of analytical results with the experimental measurements are considered quite satisfactory. The effect of elastic springback on the dent resistance analysis is found to be very significant for the panel (122 cm x 60.9 cm x 0.076 cm) subjected to a point projectile impact at 16.45 m/sec. While the amount of springback decreases as the loading speed increases, the effect due to the strain rate hardening of material, such as low carbon steel, becomes more dominant and is demonstrated in the analysis of dent resistance of a rectangular steel plate impulsively loaded.

Ni, C. M.↗
NASA NTRS1976

On the radiation of sound from baffled finite panels

Theoretical and experimental research on structural-acoustic interaction is reviewed. The emphasis is upon the radiation from and acoustic loading of baffled rectangular plates and membranes. The topics discussed include a criterion for strong radiation loading, the mass law for a finite panel, numerical calculation of the radiation impedance of a finite panel in the presence of a parallel mean flow, and experimental determination of the effect of vibration amplitude and Mach number upon panel radiation efficiency.

Leehey, P.↗
NASA NTRS1976

Advanced surface paneling method for subsonic and supersonic flow

Numerical results illustrating the capabilities of an advanced aerodynamic surface paneling method are presented. The method is applicable to both subsonic and supersonic flow, as represented by linearized potential flow theory. The method is based on linearly varying sources and quadratically varying doublets which are distributed over flat or curved panels. These panels are applied to the true surface geometry of arbitrarily shaped three dimensional aerodynamic configurations.

Erickson, L. L.↗
NASA NTRS1976

Fabrication and evaluation of advanced titanium and composite structural panels

Advanced manufacturing methods for titanium and composite material structures are being developed and evaluated. The focus for the manufacturing effort is the fabrication of full-scale structural panels which replace an existing shear panel on the upper wing surface of the NASA YF-12 aircraft. The program involves design, fabrication, ground testing, and Mach 3 flight service of full-scale structural panels and laboratory testing of representative structural element specimens.

Bales, T. T.↗
NASA NTRS1977

Flight service evaluation of Kevlar-49/epoxy composite panels in wide-bodied commercial transport aircraft

Kevlar-49 fairing panels, installed as flight service components on three L-1011s, were inspected after three years' service, and found to be performing satisfactorily. There are six Kevlar-49 panels on each aircraft, including sandwich and solid laminate wing-body panels, and 150 C service aft engine fairings. The service history to date indicates that Kevlar-49 epoxy composite materials have satisfactory service characteristics for use in aircraft secondary structure.

Stone, R. H.↗
NASA NTRS1976

Stresses in acoustically excited panels and shuttle insulation tiles

Natural vibration and acoustic response results are presented for a 36 x 18 inch panel with 18 6 x 6-inch tiles of 1.0, 1.6 and 2.3 inch thicknesses. Computed results for an untiled panel are compared with experiments performed earlier. Natural frequency and acoustic response comparisons are also given for independent analyses performed upon tiled and untiled panels. The results indicate the general applicability of the computer programs developed for use as shuttle design and analysis tools.

Otalvo, I. U.↗
NASA NTRS1977

Minimum-mass design of filamentary composite panels under combined loads: Design procedure based on a rigorous buckling analysis

A procedure is presented for designing uniaxially stiffened panels made of composite material and subjected to combined inplane loads. The procedure uses a rigorous buckling analysis and nonlinear mathematical programing techniques. Design studies carried out with the procedure consider hat-stiffened and corrugated panels made of graphite-epoxy material. Combined longitudinal compression and shear and combined longitudinal and transverse compression are the loadings used in the studies. The capability to tailor the buckling response of a panel is also explored. Finally, the adequacy of another, simpler, analysis-design procedure is examined.

Stroud, W. J.↗
NASA NTRS1979

Low-cost graphite/epoxy structural panels

Manufacturing process precures components of composite panels prior to assembly. Process separately cures the graphite/epoxy skin, stiffener ribs, and stiffener grid. After curing, panels are assembled using special adhesive. With implementation of cost effective manufacturing techniques, uses of graphite-epoxy laminate panels may be found in other areas such as auto industry.

Lager, J. R.↗
NASA NTRS1979

Voltage regulator for solar panels

Shunt voltage regulators for solar panels uses internal resistance of panel to control its output voltage. Regulator can be scaled up for high-current solar panels by adding more transistors.

Casad, T. A.↗