SEARCH · Search NASA

Results for “Temperature gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS1980

On the physics of a long decay X-ray event

The paper discusses the long decay X-ray event which appeared as an expanding loop system on the solar limb on 13-14 Aug. 1973 which was also observed temporally and spectrally. A one-dimensional hydrodynamic study was undertaken to investigate increasing and decreasing phases of the event; it was shown that the inferred temperature gradients along the loops during the heating phase are consistent with unrestricted dynamic and conductive flows along the magnetic field lines. It was concluded that it cannot be definitely stated that enhanced emission at the tops of the loops is due to pressure gradients along the field lines; also, the large emission measure variations in the 10 to the 5th to 10 to the 6th K plasma during the event's decline may be due to the temperature dependence of radiative decay within a multiloop configuration.

Krall, K. R.↗

NASA NTRS1981

Baroclinic instability of a rotating Hadley cell

The stability of a thin fluid layer between two rotating plates which are subjected to a horizontal temperature gradient is investigated. The solution for the stationary basic state is obtained in a closed form. It is pointed out that this solution identifies Ekman and thermal layers adjacent to the plates and interior temperature and velocity fields which are almost linear functions of height. The stability of that basic state with respect to infinitesimal zonal waves is then analyzed via the solution of the complete viscous linear equations for the perturbations. The character of the growth rates is found to be similar to those of the classical baroclinic waves. It is also found that the region of stability depends on the Prandtl number, the vertical stratification parameter, and both the meridional and zonal wavenumbers. The flow is generally unstable for small enough Ekman numbers and for Rossby numbers less than 10.

Antar, B. N.↗

NASA NTRS1983

Advanced methods for preparation and characterization of infrared detector materials

Crystals were prepared by the Bridgman-Stockbarger method with a wide range of crystal growth rates and temperature gradients adequate to prevent constitutional supercooling under diffusion-limited, steady-state, growth conditions. The longitudinal compositional gradients for different growth conditions and alloy compositions were calculated and compared with experimental data to develop a quantitative model of solute redistribution during the crystal growth of the alloys. Measurements were performed to ascertain the effect of growth conditions on radial compositional gradients. The pseudobinary HgTe-CdTe constitutional phase diagram was determined by precision differential-thermal-analysis measurements and used to calculate the segregation coefficient of Cd as a function of x and interface temperature. Experiments were conducted to determine the ternary phase equilibria in selected regions of the Hg-Cd-Te constitutional phase diagram. Electron and hole mobilities as functions of temperature were analyzed to establish charge-carrier scattering probabilities. Computer algorithms specific to Hg(1-x)CdxTe were developed for calculations of the charge-carrier concentration, charge-carrier mobilities, Hall coefficient, and Dermi Fermi energy as functions of x, temperature, ionized donor and acceptor concentrations, and neutral defect concentrations.

Broerman, J. G.↗

NASA NTRS2001

Shuttle Flight Experiment on USMP-4: In Situ Monitoring of Crystal Growth Using MEPHISTO

This reports on the MEPHISTO-4 experiment on the Space Shuttle Columbia, STS-87, November 19-December 5, 1997. Involved were NASA; the University of Florida at Gainesville; groups from France that developed and built the furnace; the National Institute of Standards and Technology; The University of New South Wales, Australia; and Purdue University. This was a solidification study in which three long rods of Bismuth- 1 at.% Tin were directionally solidified. The goals were to solidify in an environment free of natural convection; to determine the relationship among solidification growth velocity, growth mode, and temperature; and determine the diffusivity of Sn in Bi. The flight samples grew with a planar solid/liquid interface at velocities less than 3.4 gm/s, and cellular growth was present at velocities greater than 6.7 um/s; grain orientation influenced the planar to cellular transition. The temperature gradient in the liquid was 204 K/cm. The s/l interface was flat with slight concavity. Diffusion-dominated conditions were present during MEPHISTO-4. The Seebeck technique was used to determine the s/I interface temperature during growth, however, to date, analysis of the Seebeck results has not yielded a reliable measurement of the interface temperature. The partition coefficient for Bi alloyed with Sn was measured, k = 0.029.

Abbaschian, Reza↗

NASA NTRS2019

Systematic Error Cancellation for a Four-Port Interferometric Polarimeter

The Primordial Inflation Explorer (PIXIE) is an Explorer-class mission concept to measure the gravitational-wave signature of primordial inflation through its distinctive imprint on the linear polarization of thecosmic microwave background (CMB). Its optical system couples a polarizing Fourier transform spectrometerto the sky to measure the differential signal between orthogonal linear polarization states from two co-pointedbeams on the sky. The double differential nature of the four-port measurement mitigates beam-related systematic errors common to the two-port systems used in most CMB measurements. Systematic errors coupling unpolarized temperature gradients to a false polarized signal cancel to first order for any individual detector. Thiscommon-mode cancellation is performed optically, prior to detection, and does not depend on the instrumentcalibration. Systematic errors coupling temperature to polarization cancel to second order when comparing signals from independent detectors. We describe the polarized beam patterns for PIXIE and assess the systematicerror for measurements of CMB polarization.

Kogut, Alan J.↗

DOE OSTI2025

Neuromorphic heat transport effects in a molecular junction

Understanding energy transport at the nanoscale is an open and fundamental challenge in the molecular sciences with direct implications for the design of new electronics, computing devices, and materials. While nanoscale energy transport under steady-state conditions has been studied extensively, there is much less known about energy transport under time-dependent driving forces, particularly in the far-from-equilibrium regime. In this work, we use nonequilibrium molecular dynamics simulations and stochastic thermodynamics to investigate energy transport in a well-studied nanoscale system—a molecular junction—subjected to a time-periodic temperature gradient. The primary observation is that molecular junctions can exhibit heat transport hysteresis, a phenomenon in which the heat flux through a system depends not only on the instantaneous value of a time-dependent temperature bias but also on the temporal history of that bias. The presented findings illustrate that molecular junctions can exhibit the specific memory effect—heat transport hysteresis—that is essential for the design of thermal neuromorphic computers. This work elucidates a potential pathway toward the realization of such devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS1987

On the control of flexible structures by applied thermal gradients

Thermal, elastic, and feedback analyses are applied to the case of a beam with a distributed thermal actuator. The actuator is capable of producing a thermal gradient across the section of the beam. One candidate for such an actuator uses the Peltier effect, which appears in certain semiconductors. These devices act as heat pumps when a voltage is applied, causing a temperature gradient. It is shown that the thermal gradients can induce deflection in the beam. If the thermal gradients are applied in the proper sense to a vibrating beam, it is possible to increase the vibration damping exhibited by the structure. Experimental results are given for a cantilever beam, whose first vibrational mode damping ratio was increased from 0.81 to 7.4 percent with a simple lead compensation.

Edberg, D. L.↗

NASA NTRS1987

Control of flexible structures by applied thermal gradients

Edberg, Donald L.↗

NASA NTRS1993

Study of bubble behavior in weightlessness (effects of thermal gradient and acoustic stationary wave) (M-16)

The aim of this experiment is to understand how bubbles behave in a thermal gradient and acoustic stationary wave under microgravity. In microgravity, bubble or bubbles in a liquid will not rise upward as they do on Earth but will rest where they are formed because there exists no gravity-induced buoyancy. We are interested in how bubbles move and in the mechanisms which support the movement. We will try two ways to make bubbles migrate. The first experiment concerns behavior of bubbles in a thermal gradient. It is well known than an effect of surface tension which is masked by gravity on the ground becomes dominant in microgravity. The surface tension on the side of the bubble at a lower temperature is stronger than at a higher temperature. The bubble migrates toward the higher temperature side due to the surface tension difference. The migration speed depends on the so-called Marangoni number, which is a function of the temperature difference, the bubble diameter, liquid viscosity, and thermal diffusivity. At present, some experimental data about migration speeds in liquids with very small Marangoni numbers were obtained in space experiments, but cases of large Marangoni number are rarely obtained. In our experiment a couple of bubbles are to be injected into a cell filled with silicon oil, and the temperature gradient is to be made gradually in the cell by a heater and a cooler. We will be able to determine migration speeds in a very wide range of Marangoni numbers, as well as study interactions between the bubbles. We will observe bubble movements affected by hydrodynamical and thermal interactions, the two kinds of interactions which occur simultaneously. These observation data will be useful for analyzing the interactions as well as understanding the behavior of particles or drops in materials processing. The second experiment concerns bubble movement in an acoustic stationary wave. It is known that a bubble in a stationary wave moves toward the node or the loop according to whether its diameter is larger or smaller than that of the main resonant radius. In our experiment fine bubbles will be observed to move according to an acoustic field formed in a cylindrical cell. The existence of bubbles varies the acoustic speed, and the interactive force between bubbles will make the bubble behavior collective and complicated. This experiment will be very useful to development of bubble removable technology as well as to the understanding of bubble behavior.

Azuma, H.↗

NASA NTRS2005

Depth-Penetrating Luminescence Thermography of Thermal- Barrier Coatings

A thermographic method has been developed for measuring temperatures at predetermined depths within dielectric material layers . especially thermal-barrier coatings. This method will help satisfy a need for noncontact measurement of through-the-thickness temperature gradients for evaluating the effectiveness of thermal- barrier coatings designed to prevent overheating of turbine blades, combustor liners, and other engine parts. Heretofore, thermography has been limited to measurement of surface and near-surface temperatures. In the thermographic method that is the immediate predecessor of the present method, a thermographic phosphor is applied to the outer surface of a thermal barrier coating, luminescence in the phosphor is excited by illuminating the phosphor at a suitable wavelength, and either the time dependence of the intensity of luminescence or the intensities of luminescence spectral lines is measured. Then an emissivity-independent surface-temperature value is computed by use of either the known temperature dependence of the luminescence decay time or the known temperature dependence of ratios between intensities of selected luminescence spectral lines. Until now, depth-penetrating measurements have not been possible because light of the wavelengths needed to excite phosphors could not penetrate thermal-barrier coating materials to useful depths. In the present method as in the method described above, one exploits the temperature dependence of luminescence decay time. In this case, the phosphor is incorporated into the thermal-barrier coat at the depth at which temperature is to be measured. To be suitable for use in this method, a phosphor must (1) exhibit a temperature dependence of luminescence decay time in the desired range, (2) be thermochemically compatible with the thermal-barrier coating, and (3) exhibit at least a minor excitation spectral peak and an emission spectral peak, both peaks being at wavelengths at which the thermal-barrier coating is transparent or at least translucent. Conventional thermographic phosphors are not suitable because they are most efficiently excited by ultraviolet light, which does not penetrate thermal- barrier coating materials. (Typical thermal-barrier coating materials include or consist of various formulations of yttria-stabilized zirconia.) Only a small fraction of phosphor candidates have significant excitation at wavelengths long enough (>500 nm) for sufficient penetration of thermal-barrier coatings. One suitable phosphor material . yttria doped with europium (Y2O3:Eu) . has a minor excitation peak at 532 nm and an emission peak at 611 nm. In experiments, this material was incorporated beneath a 100-microns-thick thermal-barrier coating and subjected to excitation and measurement by the luminescence-decay-time technique. These experiments were found to yield reliable temperature values up to 1,100 C. At the time of reporting the information for this article, a search for suitable phosphors other than (Y2O3:Eu) was continuing.

Eldridge, Jeffrey↗

NASA NTRSDate not supplied

Using Digital Image Correlation for Material Testing at Cryogenic Temperatures

Recent efforts were made to parametrize an aluminum alloy at cryogenic temperatures to calibrate finite element models simulating material deformation. Digital image correlation (DIC) was used to measure material properties using front/back strains of specimens during tensile tests. Data acquired from DIC was compared to physical extensometer measurements. Two camera pairs (front and back) were mounted via aluminum extrusion to the exterior of an environmental chamber of a hydraulic test stand. Images were taken through single-pane optical glass windows of the environment chamber. Positive pressure bags encased the cameras, attaching to the perimeter of the glass to keep out moisture and prevent windows from frosting. Figure 1 shows the environmental setup and the camera setup during cryogenic testing. Some of the challenges during testing at cryogenic temperatures include the gaseous flow of liquid nitrogen in the optical path of the mounted cameras, frost buildup on the windows as seen in Figure 1b, and frost on the test coupon. The temperature gradient present during the introduction of liquid nitrogen into the chamber can increase the projection error of images captured of the specimen. Figure 2 shows the estimated projection error from DIC as a function of temperature during the cool down process. This presentation addresses some of the concerns and observations when using DIC for testing at cryogenic temperatures using methods of isolated camera system and techniques for maintaining the glass panel clear from frost.

Joseph Cochran↗

NASA NTRS1959

On Fully Developed Channel Flows: Some Solutions and Limitations, and Effects of Compressibility, Variable Properties, and Body Forces

An examination of the effects of compressibility, variable properties, and body forces on fully developed laminar flow has indicated several limitations on such streams. In the absence of a pressure gradient, but presence of a body force (e.g., gravity), an exact fully developed gas flow results. For a liquid this follows also for the case of a constant streamwise pressure gradient. These motions are exact in the sense of a Couette flow. In the liquid case two solutions (not a new result) can occur for the same boundary conditions. An approximate analytic solution was found which agrees closely with machine calculations.In the case of approximately exact flows, it turns out that for large temperature variations across the channel the effects of convection (due to, say, a wall temperature gradient) and frictional heating must be negligible. In such a case the energy and momentum equations are separated, and the solutions are readily obtained. If the temperature variations are small, then both convection effects and frictional heating can consistently be considered. This case becomes the constant-property incompressible case (or quasi-incompressible case for free-convection flows) considered by many authors. Finally there is a brief discussion of cases wherein streamwise variations of all quantities are allowed but only a such form that independent variables are separable. For the case where the streamwise velocity varies inversely as the square root distance along the channel a solution is given.

Maslen, Stephen H.↗

DOE OSTI2025

Thermal mechanical assessment of a SiC-SiC-composite clad fuel pin concept in a light water reactor environment

Accident Tolerant Fuels (ATFs) are designed to increase coping time following an accident scenario while preserving or improving current steady state reactor operational performance. A potential ATF concept is SiC-SiC composite claddings. Fuel performance simulations were conducted on a SiC-SiC based cladding concept utilizing a multilayered approach for improved performance. This cladding concept referred to as the Duplex concept is a duplex structure composed of a monolithic SiC layer placed on the outside of a SiC-SiC composite. A liquid metal is added to fuel-cladding gap for improved heat dissipation from the fuel. The monolithic SiC layer is used to improve the coolant corrosion characteristics and protect the SiC-SiC composite layer from exposure to the coolant. The fuel performance code BISON was used to conduct fuel performance simulations on the cladding concepts. Comparisons are made with a current prototypic fuel rod design (UO 2 fuel enclosed in Zircaloy-4 cladding). Representative steady-state cases were considered for normal power and two cycle power histories. Additionally, a PCI ramp case was simulated to analyze potential anticipated operational occurrences. Transient response during a Loss of Coolant Accident and a Reactivity Initiated Accident were also simulated. This computational study demonstrated that for normal operating conditions, the SiC concept cladding performed as well as the baseline for the standard power cases evaluated. The ramping evaluations indicate potential fracturing of the SiC-SiC composite of the composite cladding compared to the Zircaloy-4 cladding due to the temperature gradient and the subsequent differential thermal conductivity degradation and swelling across the composite thickness. In conclusion, the rod fails early at low enthalpy for RIA but survives a LOCA with minimal material loss due to high temperature steam corrosion.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1982

Modelling of TGS growth in space

Attention is called to the necessity of programming the temperature downward in order to maintain a constant growth rate in the absence of convection. Trial and error numerical computations are performed to find the first approximation for the required isothermal dissolution period, linear ramp, and polynomial temperature variation period. The linear ramp rate is limited by the specified maximum temperature gradient. The isothermal dissolution turns out to be unnecessary. The linear ramp must be stopped before the polynomial period is begun in order to avoid overshooting the specified maximum growth rate. After a few hours, the temperature profile approaches steady-state behavior.

Liu, L. C.↗

NASA NTRS1999

DS-2 Mars Microprobe Battery

In January of 1999 the NM DS-2 Mars microprobe will be launched to impact on Mars in December. The technical objectives of the missions are to demonstrate: key technologies, a passive atmospheric entry, highly integrated microelectronics which can withstand both low temperatures and high decelerations, and the capability to conduct in-situ, surface and subsurface science data acquisition. The scientific objectives are to determine if ice is present below the Martian surface, measure the local atmospheric pressure, characterize the thermal properties of the martian subsurface soil, and to estimate the vertical temperature gradient of the Martian soil. The battery requirements are 2-4 cell batteries, with voltage of 6-14 volts, capacity of 550 mAh at 80C, and 2Ah at 25C, shelf life of 2.5 years, an operating temperature of 60C and below, and the ability to withstand shock impact of 80,000 g's. The technical challenges and the approach is reviewed. The Li-SOCL2 system is reviewed, and graphs showing the current and voltage is displayed, along with the voltage over discharge time. The problems encountered during the testing were: (1) impact sensitivity, (2) cracking of the seals, and (3) delay in voltage. A new design resulted in no problems in the impact testing phase. The corrective actions for the seal problems involved: (1) pre weld fill tube, (2) an improved heat sink during case to cover weld and (3) change the seal dimensions to reduce stress. To correct the voltage delay problem the solutions involved: (1) drying the electrodes to reduce contamination by water, (2) assemblage of the cells within a week of electrode manufacture, (3) ensure electrolyte purity, and (4) provide second depassivation pulse after landing. The conclusions on further testing were that the battery can: (1) withstand anticipated shock of up to 80,000 g, (2) meet the discharge profile post shock at Mars temperatures, (3) meet the required self discharge rate and (4) meet environmental requirements.

Frank, H.↗

NASA NTRS1994

Springtime microwave emissivity changes in the southern Kara Sea

Springtime microwave brightness temperatures over first-year ice are examined for the southern Kara Sea. Snow emissivity changes are revealed by episodic drops in the 37- to 18-GHz brightness temperature gradient ratio measured by the Nimbus 7 scanning multichannel microwave radiometer. We suggest that the negative gradient ratios in spring 1982 result from increased scatter at 37 GHz due to the formation of a near-surface hoar layer. This interpretation is supported by the results of a surface radiation balance model that shows the melt signature occurring at below freezing temperatures but under clear-sky conditions with increased solar input to the surface. Published observations from the Greenland ice cap show a surface hoar layer forming under similar atmospheric conditions owing to the increased penetration and absorption of solar radiation just below the surface layer. In spring/early summer 1984 similar gradient ratio signatures occur. They appear to be due to several days of freeze-thaw cycling following the movement of a low-pressure system through the region. These changes in surface emissivity represent the transition from winter to summer conditions (as defined by the microwave response) and are shown to be regional in extent and to vary with the synoptic circulations.

Crane, Robert G.↗

NASA NTRS1975

Evidence for the nonuniform distribution of microwave attenuating clouds in the atmosphere of Venus - Mariner 2

Data obtained by Mariner 2 in three microwave-radiometer scans of Venus are reanalyzed using model Venusian atmospheres based on observations by Veneras 4 through 8 as well as by Mariners 5 and 10. It is noted that a previous analysis of this microwave data revealed a CO2 percentage and surface pressures that were considerably lower than those measured in situ as well as a longitudinal temperature gradient that was much larger than that indicated by the more recent measurements. The reanalysis shows that the measured scan ratios require different average values of microwave-cloud opacity for each scan and that the anomalous temperature decrease observed in the south polar region of the terminator scan requires a very opaque microwave cloud between local zenith angles of 40 and 70 deg. It is suggested that a nonuniform microwave-attenuating cloud is located below the IR and visible cloud deck of Venus.

Jones, D. E.↗

NASA NTRS1980

The effect of reduced gravity on solidification microstructures of NH4Cl-H2O alloys

The effect of gravity on the columnar-to-equiaxed microstructural transition was studied in small samples of NH4Cl-H2O. The behavior of the samples during laboratory (one gravity) experiments was contrasted with their behavior during a (low gravity) sounding rocket flight. In one gravity, the columnar zone accounted for 25 to 100 pct of the structure, depending on the superheat and orientation of the chill. Grain multiplication occurred by showering and by convection induced dendrite arm remelting. Convection was caused by both thermal gradients and solutal gradients. In low gravity, however, completely columnar structures were obtained; all grain multiplication mechanisms were entirely suppressed. Reduced gravity also modified the thermal conditions and caused the liquid to cool more slowly. This resulted in a steeper temperature gradient in the liquid ahead of the solidification interface. 'Big bang' type nucleation occurred in two of the samples, distributing nuclei throughout the liquid. Despite this, an equiaxed zone did not form, indicating that the most significant effect of low gravity on this experiment was modification of the thermal conditions.

Papazian, J. M.↗