SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Powered rotor installation, tunnel internal flow analysis using vortex ring, and flow field calculation of highly loaded systems in free air for V/STOL vehicles test program
A number of vortex shedding flowmeter designs for flow measurements in liquid oxygen ducts on the space shuttle main engines have been tested in a high head water flow test facility. The results have shown that a vortex shedding element or vane spanning the duct can give a linear response to an average flow velocity of 46 m/s (150 ft/s) in a 1 1/2 inch nominal (41 mm actual) diameter duct while a vane partially spanning the duct can give a linear response to velocities exceeding 55 m/s (180 ft/s). The maximum pressure drops across the flow sensing elements extrapolate to less than 0.7 MPa (100 psi) at 56 m/s (184 ft/s) for liquid oxygen. The test results indicate that the vanes probably cannot be scaled up with pipe size, at least not linearly.
Fluidic vortex valve warm gas flow control for rocket application
A viscous primary-secondary flow analysis designed for numerical solution by forward marching integration is applied to the tip vortex generation problem. Equations governing streamwise momentum, streamwise vorticity, and a gas law are solved in conjunction with equations governing scalar and vector surface potentials for the secondary velocities. The numerical method used combines a consistently split linearized block implicit (LBI) scheme for parabolic equations and a scalar iterative ADI scheme for elliptic equations. Computed results are presented for a wing of rectangular planform immersed in a high Reynolds number stream at 6 degrees incidence. The physical mechanism for generation of the tip vortex, as revealed by the analysis and computations, is discussed. Detailed flow results for the case of 6 degree incidence are included.
Flow phenomena and the relative performance associated with several devices for controlling turbulent separated flow were investigated at low speeds. Vortex-generating devices examined included: submerged vortex generators (Wheeler doublet and wishbone types), spanwise cylinders, large-eddy breakup devices (LEBU) at small angle of attack (alpha), and vortex-generator jets (VGJ). Dye flow visualization tests in a water tunnel indicated that wishbone vortex generators in the forward orientation shed horseshoe vortices; wishbone vortex generators oriented in the reverse direction and doublet vortex generators shed streamwise counterrotating vortices; a spanwise cylinder located near the wall and LEBUs at alpha = -10 deg produced eddies which rotated with the same sign as the mean vorticity in a turbulent boundary layer; and the most effective VGJs produced streamwise corotating vortices. Comparative wind tunnel tests conducted on a curved backward-facing ramp indicated that transferring momentum from the outer region of a turbulent boundary layer by embedded streamwise vortices is more effective than by transverse vortices for separation control applications.
A parametric cranked delta planform study has been conducted in the Langley 14- by 22-Foot Subsonic Tunnel with the following objectives: (1) to evaluate the vortex flap design methodology for cranked delta wings, (2) to determine the influence of leading-edge sweep and the outboard wing on vortex flap effectiveness, (3) to evaluate novel flow control concepts, and (4) to validate unstructured grid Euler computer code predictions with modeled vortex and trailing-edge flaps. Two families of cranked delta planforms were investigated. One family had constant aspect ratio, while the other had a constant nondimensional semispan location of the leading-edge break. The inboard leading-edge sweep of the planforms was varied between 68 deg., 71 deg., and 74 deg., while outboard leading-edge sweep was varied between 48 deg. and 61 deg. Vortex flaps for the different planforms were designed by an analytical vortex flap design method. The results indicate that the effectiveness of the vortex flaps was only slightly influenced by the variations in the parametric planforms. The unstructured grid Euler computer code was successfully used to model the configurations with vortex flaps. The vortex trap concept was successfully demonstrated.
A finite analytic (FA) numerical solution is developed for unsteady two-dimensional Navier-Stokes equations. The FA method utilizes the analytic solution in a small local element to formulate the algebraic representation of partial differential equations. The combination of linear and exponential functions that satisfy the governing equation is adopted as the boundary function, thereby improving the accuracy of the finite analytic solution. Two flows, one a starting cavity flow and the other a vortex shedding flow behind a rectangular block, are solved by the FA method. The starting square cavity flow is solved for Reynolds number of 400, 1000, and 2000 to show the accuracy and stability of the FA solution. The FA solution for flow over a rectangular block (H x H/4) predicts the Strouhal number for Reynolds numbers of 100 and 500 to be 0.156 and 0.125. Details of the flow patterns are given. In addition to streamlines and vorticity distribution, rest-streamlines are given to illustrate the vortex motion downstream of the block.
Mean-flow measurements of a supersonic turbulent streamwise vortex are presented. This vortex was produced by the injection of a swirling flow along the centerline of a supersonic airstream at Mach 3. Directional Mach number distributions, obtained via a five-hole flow-angularity probe, reveal vortex characteristics similar to those of the incompressible case, even though rotational Mach numbers up to 0.8 were obtained. This work is the first step of a study of the supersonic vortex breakdown phenomenon.
Flow visualization studies were conducted in a small pilot wind tunnel to determine qualitative effects of blowing a discrete jet essentially parallel to the leading edge of a 45 deg-swept trapezoidal wing featuring leading- and trailing-edge flaps. Test parameters included wing angle-of-attack, jet momentum coefficient, leading- and trailing-edge flap deflections, and nozzle chordwise displacement. Results of this study indicate that blowing from a reflection plane over the wing enhances the leading-edge vortex and delays vortex bursting to higher angles-of-attack and greater span distances. Increased blowing rates decrease vortex size, growth rate, and vertical displacement above the wing surface at a given span station and also extend the spanwise effectiveness of lateral blowing. Deflection of a leading-edge flap delays the beneficial effects of spanwise blowing to higher angles-of-attack. Nozzle chordwise locations investigated for the wing with and without leading-edge flap deflection appear equally effective in enhancing the separated leading-edge flow.
Amplitude and surface pressure measurements for circular cylinder in vortex flow-excited oscillation
A numerical investigation of a viscous incompressible fluid with constant properties within a vortex sink rate sensor is undertaken. A computer program was developed, for obtaining the numerical solution of the Navier-Stokes equations, assuming laminar flow, having general prescribed inlet conditions and axisymmetric boundary conditions. Computational results for various viscous flows and assorted boundary conditions have been obtained. In the vortex chamber, the radial momentum is conserved, whereas the axial momentum is negligible. In the sink region, the radial and tangential velocities, as well as the tangential vorticities, have significantly high values. In the sink tube, the radial momentum is negligible. The radial momentum within the vortex chamber is converted to the axial momentum in the sink tube. A change in the flow rate had an appreciable effect within the sensor and particularly near the sink tube entrance. As the flow rate was increased, both the tangential velocity and tangential vorticity increased rapidly. At the higher flow rates, vortices were produced at the corner of the entrance section of the sink tube.
A three dimensional, forward-marching, viscous flow analysis is applied to the tip vortex generation problem. The equations include a streamwise momentum equation, a streamwise vorticity equation, a continuity equation, and a secondary flow stream function equation. The numerical method used combines a consistently split linearized scheme for parabolic equations with a scalar iterative ADI scheme for elliptic equations. The analysis is used to identify the source of the tip vortex generation process, as well as to obtain detailed flow results for a rectangular planform wing immersed in a high Reynolds number free stream at 6 degree incidence.
Laminar incompressible viscous flow in short cylindrical vortex chamber with finite swirl ratio
Results of an experimental study are presented on the effectiveness of a vortex generator (VG) in preventing lift-off of a jet-in-cross-flow (JICF). The study is pertinent to film-cooling applications and its relevance to NASA programs is first briefly discussed. In the experiment, the jet issues into the boundary layer at an angle of 20deg to the free-stream. The effect of a triangular, ramp-shaped VG is studied while varying its geometry and location. Detailed flow-field properties are obtained for a case in which the height of the VG and the diameter of the orifice are comparable to the approach boundary layer thickness. The VG produces a streamwise vortex pair with vorticity magnitude three times larger (and of opposite sense) than that found in the JICF alone. Such a VG appears to be most effective in keeping the jet attached to the wall. The effect of parametric variation is studied mostly from surveys ten diameters downstream from the orifice. Results over a range of jet-to-freestream momentum flux ratio (1<J<11) show that the VG has a significant effect even at the highest J covered in the experiment. When the VG height is halved there is a lift-off of the jet. On the other hand, when the height is doubled, the jet core is dissipated due to larger turbulence intensity. Varying the location of the VG, over a distance of three diameters from the orifice, is found to have little impact.
If the discrete vortex lattice is considered as an approximation to the surface-distributed vorticity, then the concept of the generalized principal part of an integral yields a residual term to the vorticity-induced velocity field. The proper incorporation of this term to the velocity field generated by the discrete vortex lines renders the present vortex lattice method valid for supersonic flow. Special techniques for simulating nonzero thickness lifting surfaces and fusiform bodies with vortex lattice elements are included. Thickness effects of wing-like components are simulated by a double (biplanar) vortex lattice layer, and fusiform bodies are represented by a vortex grid arranged on a series of concentrical cylindrical surfaces. The analysis of sideslip effects by the subject method is described. Numerical considerations peculiar to the application of these techniques are also discussed. The method has been implemented in a digital computer code. A users manual is included along with a complete FORTRAN compilation, an executed case, and conversion programs for transforming input for the NASA wave drag program.
An experiment is conducted on the effectiveness of a vortex generator (VG) in preventing lift-off of a jet-in-cross-flow (JICF), with film-cooling application in mind. The jet issues into the boundary layer at an angle of 20 to the free-stream. The effect of a triangular ramp-shaped VG is studied while varying its geometry and location. Detailed flow-field properties are documented for a specific case in which the height of the VG and the diameter of the orifice are comparable to the approach boundary layer thickness. This combination of VG and JICF produce a streamwise vortex pair with vorticity magnitude three times larger (and of opposite sense) than that found in the JICF alone. Such a VG appears to be most effective in keeping the jet attached to the wall. While most of the data are taken at a jet-to-freestream momentum flux ratio (J) of 2, limited surveys are done for varying J. The VG is found to have a significant effect even at the highest J (=11) covered in the experiment. Effect of parametric variation is studied mostly from surveys ten diameters downstream from the orifice. When the VG height is halved there is a lift-off of the jet. On the other hand, when the height is doubled, the jet core is dissipated due to larger turbulence intensities. Varying the location of the VG, over a distance of three diameters from the orifice, is found to have little impact. Rounding off the edges of the VG with increasing radius of curvature progressively diminishes the effect. However, a small radius of curvature may be quite tolerable in practice.
An automated approach is presented that extracts visual and quantitative data from vortex cores produced by Navier-Stokes simulations of rotorcraft in hover mode. This approach extracts contiguous rotor tip vortex-core trajectories, cross-flow velocity profiles, and vortex-core diameter variation with wake age (azimuth angle). This automated approach is faster and more accurate than a conventional manual approach. Moreover, this new approach allows for an efficient way to quantitatively compare vortex-core profiles from different flow simulations, e.g., grid resolution studies, and validate computed results with experimental data
The fractional step and the pseudocompressibility methods for the solution of the incompressible Navier-Stokes equations are outlined. The fractional step method is based on finite-volume formulation and uses the pressure and the volume fluxes across the faces of each cell as dependent variables. The momentum equations are solved implicitly and the Poisson equation for the pressure is solved by using the multigrid method. The pseudocompressibility approach uses an implicit-higher-order-upwind differencing scheme for the convective terms together with the Gauss-Seidel line relaxation method. The dependent variables in the pseudocompressibility approach are the pressure and the cartesian velocity components in unstaggered mesh orientation. The 90-degree square duct flow, the wing-tip vortex wake flow and unsteady turbulent flows over an oscillating NACA 0015 airfoil are computed using both the fractional step and the pseudocompressibility methods. The results obtained from two different schemes are compared against experimental measurements.