Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Friction stir welded AM50 and AZ31 Mg alloys: Microstructural evolution and improved corrosion resistance

One of the major drawbacks of Mg alloys is poor weldability, caused by porosity formation during conventional fusion welding processes. Friction Stir Welding (FSW) is promising technique in this context since it is a solid state technique. Contradicting results were published in the literature regarding the FSWed Mg alloys joint's properties. Current research was performed in order to investigate the microstructure and corrosion properties of FSWed Mg alloys, studying representatives of two commercial families: wrought AZ31-H24 and die cast AM50. It was found that in both alloys recrystallization occurred during the FSW. In AM50 the mechanism of the recrystallization was continuous, manifested by dislocation rearrangement into sub grain boundaries. In AZ31 discontinuous recrystallization had occurred through grain boundaries migration - twins rotated with respect to the matrix, turning into low angle grain boundaries. Corrosion resistance has improved during the FSW in both alloys to different extents. In the AM50 alloy, the nugget exhibited significantly higher surface potential than the base metal mainly due to the higher Al concentration in the matrix of the nugget, resulting from the dissolution of Al-enrichment and β-Mg{sub 17}Al{sub 12} phase. In the AZ31 alloy, no change in Al concentration had occurred, and the surface potential measured in the nugget was only slightly higher than in the base metal. These results underline the appropriateness of the FSW for Mg alloys since during the conventional welding deterioration of the corrosion resistance occurs. - Highlights: • Following FSW, AZ31-H24 experienced discontinuous recrystallization. • In AZ31 grain boundaries migration occurred, thus twins rotated. • In die cast AM50 continuous recrystallization occurred during the FSW. • In AM50 - dislocations rearranged into sub grain boundaries. • Corrosion resistance has improved during the FSW in both alloys to different extent.

36 MATERIALS SCIENCE↗

On visualizing material flow and precipitate evolution during probeless friction stir spot welding of an Al-Li alloy

Highlights: • Severe thermal cycle and deformation refined grains and intermetallic particles in SZ. • T{sub 1} phases fully dissolved in SZ followed by re-precipitation of GP zone and δ′ phases. • The predominant flow direction remained in spiral-like pattern during P-FSSW. • Local abrasion existed in the lap-weld interface due to flow difference, forming joining. - Abstract: The precipitate evolution and material flow visualization during probeless friction stir spot welding (P-FSSW) of an Al-Li alloy has been investigated experimentally and numerically in this work. Due to severe heat input during welding, the main strengthening phases of T{sub 1} fully dissolved in the stir zone followed by the re-precipitation of GP zone and δ′ phases, assisted with the refinement of the intermetallic particles and grains. The history of material flow was three-dimensionally visualized with a tracer, studied with X-ray tomography. The experiments and the simulation results provided a consistent interpretation of a circumferential material flow which moved inwards radially near the top surface. Upward flow in the bottom sheet improved with dwell time, causing the interface to bend. Local abrasion between the two sheets due to flow difference led to the disruption of oxide layer, and formed a connection at the interface.

36 MATERIALS SCIENCE↗

Machine learning for ultrasonic nondestructive examination of welding defects: A systematic review

Recent years have seen a substantial increase in the application of machine learning (ML) for automated analysis of nondestructive examination (NDE) data. One of the applications of interest is the use of ML for the analysis of data from in-service inspection of welds in nuclear power and other industries. These types of inspections are performed in accordance with criteria described in the ASME Boiler and Pressure Vessel Code and require the use of reliable NDE techniques. The rapid growth in ML methods and the diversity of possible approaches indicate a need to assess the current capabilities of ML and automated data analysis for NDE and identify any gaps or shortcomings in current ML technologies as applied to the automated analysis of NDE data. In particular, there is a need to determine the impact of ML on the NDE reliability. This paper discusses the findings from a literature survey on the current state of ML for the automated analysis of data from ultrasonic NDE of weld flaws. It discusses an overview of ultrasonic NDE as used for weld inspections in nuclear power and other industries. Herein, data sets and ML models used in the literature are summarized, along with a generally applicable workflow for ML. Findings on the capabilities, limitations and potential gaps in feature selection, data selection, and ML model optimization are discussed. The paper identified several needs for quantifying and validating the performance of ML methods for ultrasonic NDE, including the need for common data sets.

36 MATERIALS SCIENCE↗

Influence of vibrational treatment on thermomechanical response of material under conditions identical to friction stir welding

A molecular dynamics model was constructed to describe material loading on the atomic scale by the mode identical to friction stir welding. It was shown that additional vibration applied to the tool during the loading mode provides specified intensity values and continuous thermomechanical action during welding. An increase in additional vibration intensity causes an increase both in the force acting on the workpiece from the rotating tool and in temperature within the welded area.

42 ENGINEERING↗

The use of the taguchi method and a neural-genetic approach to optimize the quality of a pulsed Nd:YAG laser welding process

In the production process of lithium-ion secondary batteries, the lap-joint quality of the safety vent and the cathode lead influences the product quality and production efficiency. A pulsed Nd:YAG laser welding machine was employed herein. The welding parameters that influence the pulsed Nd:YAG laser welding quality was evaluated by measuring the tensile-shear strength. In this study, the Taguchi method was used to perform the initial optimization of the process parameters. A neural network (NN) with the Levenberg–Marquardt back-propagation algorithm was adopted to develop the nonlinear relationship between factors and the response. Then, a genetic algorithm based on a well-trained NN model was applied to determine the optimal factor settings. Experimental results illustrated the proposed approach.

42 ENGINEERING↗

Physical processes involved in strip electrode welding using the method of slatted splicing

Physical processes that take place in a strip electrode during welding using the slatted splicing technique are considered. Flowing of the welding current in the electrode is shown to be the key process which determines electrode heating and melting. Technological receipts are proposed that allow obtaining high-quality welds by the method of slatted splicing.

36 MATERIALS SCIENCE↗

Effect of Electron Beam Oscillation Figures on Weld Surface Condition and Cross Sectional Morphology [Slides]

Overview - Problem: Preliminary experiments showed weld depth and surface condition are not consistent among different oscillation figures. Investigation: 1. Study the circle and concentric circle figures, and directional variants of these; 2. Measure the effect of frequency on the figure; 3. Produce beam figures of equal diameter; 4. Produce welds using equal diameter beam figures 5. Correlate weld depth, surface condition, and root defects with the beam figure.

42 ENGINEERING↗

Influence of Aluminum Coatings on the Quality of Weld Joints

The application of a longitudinal magnetic field in welding aluminum coated sheet is considered. A special welding head is used to produce weld joints of satisfactory quality. Findings are obtained regarding the formation and metallographic structure of the metal in the seam, with the segregation of aluminum over its cross section. The formation of composite structure is noted.

42 ENGINEERING↗

In Situ Study on Fracture Behavior of Thick-Section Friction Stir-Welded AA 5083 Alloy

Friction stir welding (FSW) produces a gradient microstructure with distinct metallurgical zones. Here, the present study focuses on characterizing the fracture behavior during uniaxial loading across thick-section FSW joint in nonheat-treatable 5083 aluminum alloy. The hardness variation is linked to microstructural features across the weld zones through correlative microscopy. Notably, the heat-affected zone (HAZ) exhibits a lower hardness of 75 HV, while the thermomechanically affected zone (TMAZ) and stir zones (SZ) display a hardness of around 79HV. A marginal difference in hardness in HAZ prompts strain localization in HAZ on the advancing side of the weld, resulting in offset in fracture from the SZ, which is captured through in situ monitoring of the tensile test. Further, the postdeformation analysis reveals crack propagation along the maximum shear stress plane due to the coalescence of microvoids resulting from the fracturing and debonding of second-phase particles. Overall, this study provides valuable insight for optimizing the FSW process of AA 5083 alloy for thick-section applications.

36 MATERIALS SCIENCE↗

Surface engineering to enhance heat generation and joint strength in dissimilar materials AZ31 and DP590 ultrasonic welding

A multiscale simulation approach was developed and employed to optimize the sheet surface conditions for higher interfacial temperature and joint strength in ultrasonic welding of magnesium alloy AZ31 and dual-phase steel DP590. First, a mesoscale model was used to study the relationship between friction coefficient and surface roughness, which can be modified by various engineering methods. Then a macroscopic process model was employed to study the effects of surface roughness on heat generation, indicating that a temperature increase can be achieved with rougher surfaces on two sides of both DP590 and AZ31 sheets. Samples prepared by sanding and filing, as well as grinding, were first characterized for surface roughness and then welded under ultrasonic vibration. An infrared camera was used to measure temperatures in situ for model validation. Overall, lap shear test results for the welded joint showed that the joint strength can be improved by 10~25% using filing and round grinding methods as a result of the enhanced heat generation and mechanical interlocking on the interface.

42 ENGINEERING↗

Estimate of the allowable dimensions of diagnosed defects in category III and IV welded pipeline joints{sup 1}

An approach for estimating the permissible dimensions of technological defects in butt welded joints in category III and IV pipelines is described. The allowable size of a welding defect is determined from the condition of compliance with the specifications on strength for a reference cross section (damaged joint) of the pipeline taking into account its weakening by a given defect.With regard to the fairly widespread discovery of technological defects in butt welded joints during diagnostics of auxiliary pipelines for thermal electric power plants, the proposed approach can be used in practice by repair and consulting organizations.

42 ENGINEERING↗

An Alternative Frictional Boundary Condition for Computational Fluid Dynamics Simulation of Friction Stir Welding

For better application of numerical simulation in optimization and design of friction stir welding (FSW), this paper presents a new frictional boundary condition at the tool/workpiece interface for computational fluid dynamics (CFD) modeling of FSW. The proposed boundary condition is based on an implementation of the Coulomb friction model. Using the new boundary condition, the CFD simulation yields non-uniform distribution of contact state over the tool/workpiece interface, as validated by the experimental weld macrostructure. It is found that interfacial sticking state is present over large area at the tool-workpiece interface, while significant interfacial sliding occurs at the shoulder periphery, the lower part of pin side, and the periphery of pin bottom. Due to the interfacial sticking, a rotating flow zone is found under the shoulder, in which fast circular motion occurs. The diameter of the rotating flow zone is smaller than the shoulder diameter, which is attributed to the presence of the interfacial sliding at the shoulder periphery. For the simulated welding condition, the heat generation due to friction and plastic deformation makes up 54.4 and 45.6% of the total heat generation rate, respectively. In conclusion, the simulated temperature field is validated by the good agreement to the experimental measurements.

36 MATERIALS SCIENCE↗

Microstructural and Electrochemical Evaluation of Fusion Welded Low-Nickel and 304 SS at Different Heat Input

The present research study investigates the effect of heat input using E 308 electrode (controlled by welding current, i.e., 70, 85 and 100 A) on microstructure, mechanical properties and corrosion behavior of low-nickel and 304 stainless steel (SS) weldments produced by shielded metal arc welding technique. SEM investigation shows that with the higher heat input, δ-ferrite content was reduced. Dendrite and inter-dendritic length is also reduced by lowering the heat input. For all the heat inputs, it is observed that δ-ferrite content was higher in 304 stainless steel (SS) as compared to that of low-nickel austenitic stainless steel (Cr-Mn SS). Considering the heat input for Cr-Mn SS, coarse grains were observed in the heat-affected zone region. For low heat input (LHI), tensile fracture surface has exhibited river-like pattern with dimple appearance. Corrosion studies show better pitting resistance for low heat input (LHI) samples due to higher δ-ferrite present in the weld region. Similarly, higher interphase corrosion resistance is observed in both the SS grades causing more dissolution in the LHI samples.

36 MATERIALS SCIENCE↗

Improving Joint Formation and Tensile Properties of Dissimilar Friction Stir Welding of Aluminum and Magnesium Alloys by Solving the Pin Adhesion Problem

Friction stir welding (FSW), as a solid-state welding technology invented by TWI in 1991, has potential to join dissimilar Al/Mg alloys. In this study, the pin adhesion phenomenon affecting joint quality during FSW of 6061-T6 aluminum and AZ31B magnesium alloys was investigated. The adhesion phenomenon induced by higher heat input easily transformed the tapered-and-screwed pin into a tapered pin, which greatly reduced the tool’s ability to drive the plasticized materials and further deteriorated joint formation. Under the condition without the pin adhesion, the complex intercalated interlayer at the bottom of stir zone was beneficial to mechanical interlocking of Al/Mg alloys, improving tensile properties. However, the formation of intermetallic compounds was still the main reason of the joint fracture, significantly deteriorating tensile properties. Under the welding speed of 60 mm/min without the pin adhesion phenomenon, the maximum tensile strength of 107 MPa and elongation of 1.2% were achieved.

36 MATERIALS SCIENCE↗

Investigation of Hydrogen Embrittlement Susceptibility of X80 Weld Joints by Thermal Simulation

The objective of this study was to investigate the hydrogen embrittlement (HE) susceptibility and influence mechanism of X80 weld joints. Slow strain rate testing (SSRT) under in situ H-charging, combined with microstructure and fracture analysis, was performed on the base metal (BM), weld metal (WM), thermally simulated fine-grained heat-affected zone (FGHAZ) and coarse-grained heat-affected zone (CGHAZ). Results showed that the WM and simulated HAZ had a greater degree of high local strain distribution than the BM; compared to the CGHAZ, the FGHAZ had lower microhardness and more uniformly distributed stress. SSRT results showed that the weld joint was highly sensitive to HE; the HE index decreased in the following sequence: FGHAZ, WM, CGHAZ and BM. The effect of the microstructure on HE was mainly reflected in microstructure, local stress distribution and microhardness.

36 MATERIALS SCIENCE↗

Effect of Heat Exposure on the Fatigue Properties of AA7050 Friction Stir Welds

This work examines the effect of heat exposure on the subsequent monotonic and fatigue properties of friction stir-welded AA7050. Mechanical characterization tests were conducted on friction stir-welded specimens as-welded (AW) and specimens heated to 315 °C in air for 20 min. Monotonic testing revealed high joint efficiencies of 98% (UTS) in the AW specimens and 60% in the heat-damaged (HD) specimens. Experimental results of strain-controlled fatigue testing revealed shorter fatigue lives for the HD coupons by nearly a factor of four, except for the highest strain amplitude tested. Postmortem fractography analysis found similar crack initiation or propagation behavior between the AW and HD specimens; however, the failure locations for the AW were predominantly in the heat-affected zone, while the HD specimens also failed in the stir zone. Microhardness measurements revealed a relatively uniform strength profile in the HD group, accounting for the variety of failure locations observed. The differences in both monotonic and cyclic properties observed between the AW and HD specimens support the conclusion that the heat damage (315 °C at 20 min) acts as an over-aging and a quasi-annealing treatment.

36 MATERIALS SCIENCE↗

Effect of Rotation Speed on the Microstructure and Mechanical Properties of Friction-Stir-Welded CuSn6 Tin Bronze

Four-mm-thick CuSn6 tin bronze plates were friction stir welded at a constant tool traverse speed of 100 mm min{sup −1}. Favorable joints could be obtained with rotation speeds ranging from 600 to 1000 rev min{sup −1}, and groove was found on the surface of the joint under 400 rev min{sup −1}. The microstructure of the weld nugget zone was characterized by equiaxed recrystallized grains with heterogeneity along the thickness direction. Moreover, the grain size of the thermo-mechanically affected zone and stir zone increased with the increase in rotation speed. Hardness of the stir zone was higher than that of other zones due to microstructural refinement. There was little change in tensile properties of the defect-free welded joints. During tensile test, all of the defect-free joints were fractured at heat-affected zone with typical plastic fracture.

36 MATERIALS SCIENCE↗

Effect of Boron Content on Hot Ductility and Hot Cracking Susceptibility in 316L Austenitic Stainless Steel for Welding Components

Liquation cracking may occur in the heat-affected zone during welding. Two factors influence this phenomenon: the tensile stresses generated during welding and the potential loss of ductility due to the presence of a liquid film at grain boundaries depending on their chemical composition. Gleeble hot ductility tests have been used to study the combined effect of boron content and holding time on ductility drop in the liquation temperature range of a 316L type austenitic stainless steel. It is shown that high boron contents and short holding times promote the loss of ductility in this temperature range. Secondary ion mass spectrometry has been used to correlate mechanical results to boron distribution either at grain boundaries or in the bulk. Other welding tests have been performed to confirm the influence of boron content on hot cracking sensitivity of AISI 316L stainless steels. Results indicate that cracks appear on all specimens but at different strain levels. The higher the boron content is, the more the specimen exhibits tendency to hot cracking.

36 MATERIALS SCIENCE↗