SEARCH · Search NASA

Results for “active”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Localized, Non-Harmonic Active Flap Motions for Low Frequency In-Plane Rotor Noise Reduction

A first-of-its-kind demonstration of the use of localized, non-harmonic active flap motions, for suppressing low frequency, in-plane rotor noise, is reported in this paper. Operational feasibility is verified via testing of the full-scale AATD/Sikorsky/UTRC active flap demonstration rotor in the NFAC's 40- by 80-Foot anechoic wind tunnel. Effectiveness of using localized, non-harmonic active flap motions are compared to conventional four-per-rev harmonic flap motions, and also active flap motions derived from closed-loop acoustics implementations. All three approaches resulted in approximately the same noise reductions over an in-plane three-by-three microphone array installed forward and near in-plane of the rotor in the nearfield. It is also reported that using an active flap in this localized, non-harmonic manner, resulted in no more that 2% rotor performance penalty, but had the tendency to incur higher hub vibration levels.

FLAPS(CONTROL SURFACES)↗

NASA NTRS2012

Photospheric Magnetic Evolution in the WHI Active Regions

Sequences of line-of-sight (LOS) magnetograms recorded by the Michelson Doppler Imager are used to quantitatively characterize photospheric magnetic structure and evolution in three active regions that rotated across the Sun s disk during the Whole Heliosphere Interval (WHI), in an attempt to relate the photospheric magnetic properties of these active regions to flares and coronal mass ejections (CMEs). Several approaches are used in our analysis, on scales ranging from whole active regions, to magnetic features, to supergranular scales, and, finally, to individual pixels. We calculated several parameterizations of magnetic structure and evolution that have previously been associated with flare and CME activity, including total unsigned magnetic flux, magnetic flux near polarity-inversion lines, amount of canceled flux, the "proxy Poynting flux," and helicity flux. To catalog flare events, we used flare lists derived from both GOES and RHESSI observations. By most such measures, AR 10988 should have been the most flare- and CME-productive active region, and AR 10989 the least. Observations, however, were not consistent with this expectation: ARs 10988 and 10989 produced similar numbers of flares, and AR 10989 also produced a few CMEs. These results highlight present limitations of statistics-based flare and CME forecasting tools that rely upon line-of-sight photospheric magnetic data alone.

Welsch, B. T.↗

NASA NTRS2014

Multi-Source Autonomous Response for Targeting and Monitoring of Volcanic Activity

The study of volcanoes is important for both purely scientific and human survival reasons. From a scientific standpoint, volcanic gas and ash emissions contribute significantly to the terrestrial atmosphere. Ash depositions and lava flows can also greatly affect local environments. From a human survival standpoint, many people live within the reach of active volcanoes, and therefore can be endangered by both atmospheric (ash, debris) toxicity and lava flow. There are many potential information sources that can be used to determine how to best monitor volcanic activity worldwide. These are of varying temporal frequency, spatial regard, method of access, and reliability. The problem is how to incorporate all of these inputs in a general framework to assign/task/reconfigure assets to monitor events in a timely fashion. In situ sensing can provide a valuable range of complementary information such as seismographic, discharge, acoustic, and other data. However, many volcanoes are not instrumented with in situ sensors, and those that have sensor networks are restricted to a relatively small numbers of point sensors. Consequently, ideal volcanic study synergistically combines space and in situ measurements. This work demonstrates an effort to integrate spaceborne sensing from MODIS (Terra and Aqua), ALI (EO-1), Worldview-2, and in situ sensing in an automated scheme to improve global volcano monitoring. Specifically, it is a "sensor web" concept in which a number of volcano monitoring systems are linked together to monitor volcanic activity more accurately, and this activity measurement automatically tasks space assets to acquire further satellite imagery of ongoing volcanic activity. A general framework was developed for evidence combination that accounts for multiple information sources in a scientist-directed fashion to weigh inputs and allocate observations based on the confidence of an events occurrence, rarity of the event at that location, and other scientists' inputs. The software framework uses multiple source languages and is a general framework for combining inputs and incrementally submitting observation requests/reconfigurations, accounting for prior requests. The autonomous aspect of operations is unique, especially in the context of the wide range of inputs that includes manually inputted electronic reports (such as the Air Force Weather Advisories), automated satellite-based detection methods (such as MODVOLC and GOESVOLC), and in situ sensor networks.

Davies, Ashley G.↗

NASA NTRS2013

Variability of a Stellar Corona on a Time Scale of Days: Evidence for Abundance Fractionation in an Emerging Coronal Active Region

Elemental abundance effects in active coronae have eluded our understanding for almost three decades, since the discovery of the first ionization potential (FIP) effect on the sun. The goal of this paper is to monitor the same coronal structures over a time interval of six days and resolve active regions on a stellar corona through rotational modulation. We report on four iso-phase X-ray spectroscopic observations of the RS CVn binary EI Eri with XMM-Newton, carried out approximately every two days, to match the rotation period of EI Eri. We present an analysis of the thermal and chemical structure of the EI Eri corona as it evolves over the six days. Although the corona is rather steady in its temperature distribution, the emission measure and FIP bias both vary and seem to be correlated. An active region, predating the beginning of the campaign, repeatedly enters into our view at the same phase as it rotates from beyond the stellar limb. As a result, the abundances tend slightly, but consistently, to increase for high FIP elements (an inverse FIP effect) with phase. We estimate the abundance increase of high FIP elements in the active region to be of about 75% over the coronal mean. This observed fractionation of elements in an active region on time scales of days provides circumstantial clues regarding the element enrichment mechanism of non-flaring stellar coronae.

Nordon, R.↗

NASA NTRS2017

Evaluation and Certification of Ambersorb 4652 for use in Activated Carbon Ion Exchange Filters for the International Space Station

In order to reduce the infiltration of dimethylsilanediol (DMSD) and other organosilicon containing species through the Multifiltration Beds (MF Beds), an alternate activated carbon was found to replace the obsolete Barnabey Cheney 580-26 activated carbon. The carbon that removed the most organosilicon compounds in testing1 was a synthetic activated carbon named Schunk 4652 which later became Ambersorb 4652. Since activated carbon has a large capacity for iodine (I2), and is used in the Activated Carbon Ion Exchange (ACTEX) filters on the International Space Station (ISS), testing was performed on the Ambersorb 4652 carbon to determine the effectiveness of the material for use in ACTEX filters to remove iodine. This work summarizes the testing and the certification of Ambersorb 4652 for use in the ACTEX filters for the ISS.

Adam, Niklas↗

NASA NTRS2016

Statistical Correlation of Low-Altitude ENA Emissions with Geomagnetic Activity from IMAGE MENA Observations

Plasma sheet particles transported Earthward during times of active magnetospheric convection can interact with exospheric/thermospheric neutrals through charge exchange. The resulting Energetic Neutral Atoms (ENAs) are free to leave the influence of the magnetosphere and can be remotely detected. ENAs associated with low-altitude (300-800 km) ion precipitation in the high-latitude atmosphere/ionosphere are termed low-altitude emissions (LAEs). Remotely observed LAEs are highly nonisotropic in velocity space such that the pitch angle distribution at the time of charge exchange is near 90deg. The Geomagnetic Emission Cone of LAEs can be mapped spatially, showing where proton energy is deposited during times of varying geomagnetic activity. In this study we present a statistical look at the correlation between LAE flux (intensity and location) and geomagnetic activity. The LAE data are from the MENA imager on the IMAGE satellite over the declining phase of solar cycle 23 (2000-2005). The SYM-H, AE, and Kp indices are used to describe geomagnetic activity. The goal of the study is to evaluate properties of LAEs in ENA images and determine if those images can be used to infer properties of ion precipitation. Results indicate a general positive correlation to LAE flux for all three indices, with the SYM-H showing the greatest sensitivity. The magnetic local time distribution of LAEs is centered about midnight and spreads with increasing activity. The invariant latitude for all indices has a slightly negative correlation. The combined results indicate LAE behavior similar to that of ion precipitation.

Mackler, D. A.↗

NASA NTRS2016

Active Full-Shell Grazing-Incidence Optics

MSFC has a long history of developing full-shell grazing-incidence x-ray optics for both narrow (pointed) and wide field (surveying) applications. The concept presented in this paper shows the potential to use active optics to switch between narrow and wide-field geometries, while maintaining large effective area and high angular resolution. In addition, active optics has the potential to reduce errors due to mounting and manufacturing lightweight optics. The design presented corrects low spatial frequency error and has significantly fewer actuators than other concepts presented thus far in the field of active x-ray optics. Using a finite element model, influence functions are calculated using active components on a full-shell grazing-incidence optic. Next, the ability of the active optic to effect a change of optical prescription and to correct for errors due to manufacturing and mounting is modeled.

Full-shell↗

NASA NTRS2017

Observations, Modeling, and Predictions of Solar Activity From the Deep Interior to the Corona

Solar activity is a manifestation of magnetic self-organization processes that involve complex dynamical coupling of various layers of the Sun acting over a broad range of spatial and temporal scales. Synergy of observational, theoretical, and modeling efforts is key to understanding solar activity variation, dynamics, and evolution and to developing reliable physics-based forecasts of long-term solar cycles and short-term activity manifestations, “seasons of solar activity”, such as periods of enhanced flaring and CME activity. The session welcomes observers, modelers, and theoreticians to share their results and ideas and to discuss current challenges, development of emerging fields (such as data assimilation), and the analysis of historical and modern observational data using theoretical modeling, interpretations, and predictions.

Deep Interior↗

NASA NTRS1995

Transient Structure Current Generated by the Activation of a Squib Device

Experimental measurements of the currents in pyro-activation circuits show that a structure current is generated during the pyro-activation process. This current is a transient current and is an intense source of electromagnetic interference. Analysis has indicated that the noise voltage induced on candidate victim circuits is sufficient to cause circuit upset and/or latchup. A survey of flight anomaly records has also correlated the occurrence of anomalies with the pyro-activation process. Detailed analyses, taking the spacecraft cabling configuration and circuit sensitivities into account, have shown that the structure current induced noise voltage could definitely be the cause of the anomalies. The threat of the structure current due to pyro-activation can be alleviated by isolating the pyro-activation circuit from ground and by proper arrangement of the cables in sensitive circuits.

pyrotechnic↗

NASA NTRSDate not supplied

Assessment of Crew Time for Maintenance and Repairs Activities for Lunar Surface Missions

NASA is currently evaluating different methods to predict how much time crewmembers will spend conducting repair and maintenance activities on future space missions. As mission scope and spacecraft architectures change, it will be necessary to understand how crew repair and maintenance timelines are impacted by mission operations and technology changes. Past work has been done using historical ISS data to accurately predict crew habitation and operation timelines, resulting in the development of NASA’s Exploration Crew Time Model (ECTM). However, understanding crew maintenance and repair requirements has posed a unique challenge due to the complexity of available datasets, the probabilistic nature of sub-system failures, and the impacts of reliability growth on failure rates. This paper presents a methodology to collect and condition empirical repair and maintenance time data from available data sets, to extrapolate from that data to estimate projected maintenance and repair times for a lunar Surface Habitat, and to assess how uncertainty in repair time could impact utilization time on the lunar surface. NASA International Space Station (ISS) maintenance and crew time data are logged into two central databases, the Maintenance Data Collection (MDC) and the Operations Planning Timeline Integration System (OPTimIS) respectively. Separately, each of these two datasets capture only portions of the complete set of data required to generate an accurate assessment of crew time spent on maintenance activities at a sub-system level. MDC provides a detailed catalog of failure events and an overview of the failure’s required maintenance and OPTimIS provides a description of crew activities and crew time durations dedicated to maintenance. To create a more useful crew time estimate for maintenance timelines, the authors developed a methodology to capture relevant data from each set and combine and utilize that data by linking crew time requirements to specific components. The authors compare the failure logs in the MDC to crew activity logs pulled from OPTimIS and then process the data to estimate required repair times for each failure event. Data is also classified by the outcome of each repair event, whether the failed component was replaced or whether it was repaired in place. The entire maintenance activity dataset is then categorized based on the class of failed component to allow for a statistically significant sample size for each class and to provide accurate crew time estimates for any components lacking relevant data. This resultant component repair time data can be used in the future to generate Mean Time To Repair (MTTR) estimates and confidence intervals for each class of component based on a probabilistic distribution of documented maintenance events. These improved MTTR values can then be applied to candidate element sub-system architectures, along with component Mean Time Between Failure (MTBF) data to generate distributions for potential required system crew repair time estimates for a given mission. Repair time distributions can then be used to develop more accurate crew schedules and to assess potential available utilization time.

Crew Time↗

NASA NTRS2021

Technical Note: AQMEII4 Activity 1: Evaluation of Wet and Dry Deposition Schemes as an Integral Part of Regional-scale Air Quality Models

We present in this technical note the research protocol for phase 4 of the Air Quality Model Evaluation International Initiative (AQMEII4). This research initiative is divided into two activities, collectively having three goals: (i) to define the current state of the science with respect to representations of wet and especially dry deposition in regional models, (ii) to quantify the extent to which different dry deposition parameterizations influence retrospective air pollutant concentration and flux predictions, and (iii) to identify, through the use of a common set of detailed diagnostics, sensitivity simulations, model evaluation, and reduction of input uncertainty, the specific causes for the current range of these predictions. Activity 1 is dedicated to the diagnostic evaluation of wet and dry deposition processes in regional air quality models (described in this paper), and Activity 2 to the evaluation of dry deposition point models against ozone flux measurements at multiple towers with multiyear observations (to be described in future submissions as part of the special issue on AQMEII4). The scope of this paper is to present the scientific protocols for Activity 1, as well as to summarize the technical information associated with the different dry deposition approaches used by the participating research groups of AQMEII4. In addition to describing all common aspects and data used for this multi-model evaluation activity, most importantly, we present the strategy devised to allow a common process-level comparison of dry deposition obtained from models using sometimes very different dry deposition schemes. The strategy is based on adding detailed diagnostics to the algorithms used in the dry deposition modules of existing regional air quality models, in particular archiving diagnostics specific to land use–land cover (LULC) and creating standardized LULC categories to facilitate cross-comparison of LULC-specific dry deposition parameters and processes, as well as archiving effective conductance and effective flux as means for comparing the relative influence of different pathways towards the net or total dry deposition. This new approach, along with an analysis of precipitation and wet deposition fields, will provide an unprecedented process-oriented comparison of deposition in regional air quality models. Examples of how specific dry deposition schemes used in participating models have been reduced to the common set of comparable diagnostics defined for AQMEII4 are also presented.

Air Quality Model Evaluation International Initiat↗

NASA NTRS2020

Event-Driven Modeling and Execution of Robotic Activities and Contingencies in the Europa Lander Mission Concept Using BPMN

TRACE (Traceable Robotic Activity Composer and Executive) is a tool designed to address the model-ing, verification, and execution of planned and con-tingent activities during robotic space missions. These activities can be modeled (i.e., planned) graph-ically in TRACE using the Business Process Model and Notation (BPMN) language. This standardized language is used to model a sequence of robotic ac-tivities tied together by logical constructs, events, and time. TRACE includes verification tools to en-sure feasibility before mission models are executed by TRACE’s executive, which is integrated into the autonomy subsystem via a connector. In this paper, we describe TRACE in detail as it would apply to a conceptual Europa Lander surface mission with planned excavation and sample collection activities, as well as, contingency activities when execution is off-nominal—all highlighting our novel use of BPMN as a lingua franca for the pipeline from mis-sion planning to autonomous execution.

Lim, Grace↗

NASA NTRSDate not supplied

A Review of Options for a National Lab for Microgravity/Orbital Activities in LEO

NASA’s Office of Technology, Policy, and Strategy (OTPS) performs data-driven assessments to inform the Agency’s development of policy and strategy. OTPS works across NASA, the US government, industry, and academia to incorporate relevant stakeholder input to data-driven assessments regarding the future of NASA. OTPS conducted a study with the goal of identifying potential models to ensure that NASA and its government-sponsored user communities can successfully complete activities in low-Earth orbit (LEO) in a post-International Space Station (ISS) (i.e. 2030s) timeframe. Given the expectation that one or more Commercial LEO Destinations will replace the ISS by 2030, NASA leadership is considering next steps for microgravity research and other activities in LEO. This task is particularly challenging due to the uncertain future of the LEO ecosystem. Future scenarios may range from a robust environment with multiple platform options and new activities to an austere environment with few platform options and deflated momentum among user communities. Both extreme futures, along with any number of scenarios in between, have serious implications for the future of LEO and NASA’s role in it. It is therefore imperative that NASA consider its prioritized activities for the 2030 timeframe and identify potential business and operating models that will provide continuity for government-sponsored activities. The results of this NASA OTPS study will be presented, along with a discussion of how specific engagement models could enable NASA and other entities to achieve their goals in the 2030 timeframe.

Erica Marie Rodgers Heusinkveld↗

NASA NTRSDate not supplied

Simulation of etch pit formation through active sites in carbon fiber micro-structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation as a result of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gasses such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRS2023

The 2023 Meteor Shower Activity Forecast for the Lunar Surface

The purpose of this document is to provide a forecast of major meteor shower activity on the lunar surface. While the predictions in this document are for the surface, spacecraft orbiting the Moon at low altitudes will encounter meteoroids at similar rates. Most annual showers are expected to display typical activity, but the eta Aquariids (ETA) are expected to display more than double their typical activity level. A complete discussion of expected meteor shower activity in 2023 is available in the meteor shower activity forecast for low Earth orbit [1].

Althea Moorhead↗

NASA NTRSDate not supplied

Imdr Regio: The Geology of A Possible Active Hot Spot on Venus and A Target for Future Exploration By the ESA Envision Mission.

With Venus being the focus of future new missions like ESA’s EnVision, we need to look for target sites for future investigations on Venus. The different instruments will help to study the planet in a unprecedented detail. In particular, the VenSAR instrument will map the 20% of the surface of Venus at a resolution of 5 to 10 meters/pixel, so it gets crucial to select what areas of Venus deserve to be targeted for such a high-resolution mapping. We propose here Imdr Regio as a good candidate location for combined high resolution SAR mapping and for study with the rest of the mission instruments (e.g., Subsurface Radar Sounder). Imdr Regio is a large topographic rise that extends approximately from 35ºS-50ºS and 195ºE-225ºE between the volcanic plains of Helen, Nsomeka and Wawalag Planitiae. Imdr Regio was classified as a volcano-dominated topographic rise with a minimum-maximum diameter of 1200-1400 km and a swell height of 1.6 km. The southeast of Imdr Regio is dominated by Idunn Mons (46.5ºS/214.5ºE). Studies using the 1 µm (derived) surface emissivity from the Venus Express mission of the volcanic flows surrounding Idunn Mons suggest that high emissivity values in the volcano flanks are related to relatively unweathered basaltic rock and therefore indicative of a recent or even ongoing volcanic activity. We have carried out geologic mapping in the area to constrain volcanic and tectonic structures, and the geologic history of the large topographic rise. This geologic mapping reveals that different styles of volcanism are present across Imdr Regio and that this volcanic activity takes place in all the hot spot in close relation with the formation of a rift throughout all time represented by in the area. The first stages on the evolution of this large volcano are characterized by the formation of a radial fracture system and contemporaneous large sheet flows. These large sheet flows are locally difficult to distinguish from regional plains and are also deformed by regional N-trending wrinkle ridges. After this initial phase, multiple overlapping digitate flow units form the flanks and summit of the volcano and are contemporaneous with NW-SE trending fractures and graben of Olapa Chasma, a rift system that cross the topographic rise. To the northwest another large volcano also presents a system of radial fractures but lacks clear large sheet flows. Numerous pit chains are associated to fractures and graben, suggesting that transport of magma under the surface is important. The geologic history based on the mapping suggests that activity in Imdr Regio started with the emplacement of a plume/diapir in the southeast, which resulted in the formation of a radial dyke system and the emplacement of large sheet flows in Idunn Mons. The presence of other large volcanoes to the northwest suggests the presence of another magmatic source (plume or diapir). After this initial stage, volcanism continues in Idunn Mons and activity in the topographic rise is strongly related to the formation of Olapa Chasma. Rift-related volcanic flows postdate these other volcanoes and are contemporaneous with the late activity in Idunn Mons. Monogenetic volcanism is present in the rift and in all the units that are in the area.

I. López↗

NASA NTRSDate not supplied

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

DSMC↗