Search NASA⌕ Search

SEARCH · Search NASA

Results for “analyzable function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Double-sided electron energy analyzer for measurement of non-Maxwellian electron energy distributions

Here, a double-sided electron energy analyzer is developed for studies of magnetic reconnection. It can measure electron energy distribution functions along two directions opposite to each other at the same time. Each side is composed of a floating reference grid, an energy selector grid, and a collector plate. The voltage of the selector grid is swept from –40 to 0 V with respect to the reference grid with a frequency of 1 MHz. This fast sweeping is required to resolve sub-Alfvénic changes in plasma quantities of the Magnetic Reconnection Experiment, where the typical Alfvénic time is a few microseconds. The reliability of the energy analyzer is checked in Maxwellian plasmas away from the reconnection region. In this case, the electron temperature computed from the electron energy distribution function agrees with measurements of a reference triple Langmuir probe. When it is located near the reconnection region, the temperatures of the tail electron population from both sides, facing into the electron flow and facing away from it, exceed the bulk electron temperature measured by the Langmuir probe by a factor of about 2.

47 OTHER INSTRUMENTATION↗
DOE OSTI2018

Elemental mapping and geochemical characterization of gas producing shales by laser induced breakdown spectroscopy

Laser induced breakdown spectroscopy (LIBS) has been used for the analysis of hydrocarbon bearing shale samples. Shale samples taken from a Marcellus gas well at depths ranging from 7498 to 7551 ft (2285.4–2301.5 m) were analyzed by LIBS using an 81 × 81 grid pattern covering an 8 × 8 mm area. The data collected from these experiments were used to construct 2D elemental maps for each sample including the hydrocarbon forming elements C and H. Results show that the spatial elemental composition of the shale varies due to the matrix of the rock, and as a function of the sample depth. The accuracy of the analysis was confirmed by analyzing a shale sample of known elemental concentrations and obtaining a good agreement between analyzed and reference values. It has been shown that LIBS can be used to determine elemental composition variations in hydrocarbon bearing shales in a laboratory setting. In conclusion, extending this capability into wellbores will enable producers to rapidly target resources with greater accuracy.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

Impact of acute temperature and air pollution exposures on adult lung function: A panel study of asthmatics

Background Individuals with respiratory conditions, such as asthma, are particularly susceptible to adverse health effects associated with higher levels of ambient air pollution and temperature. This study evaluates whether hourly levels of fine particulate matter (PM 2.5 ) and dry bulb globe temperature (DBGT) are associated with the lung function of adult participants with asthma. Methods and findings Global positioning system (GPS) location, respiratory function (measured as forced expiratory volume at 1 second (FEV 1 )), and self-reports of asthma medication usage and symptoms were collected as part of the Exposure, Location, and Lung Function (ELF) study. Hourly ambient PM 2.5 and DBGT exposures were estimated by integrating air quality and temperature public records with time-activity patterns using GPS coordinates for each participant (n = 35). The relationships between acute PM 2.5 , DBGT, rescue bronchodilator use, and lung function collected in one week periods and over two seasons (summer/winter) were analyzed by multivariate regression, using different exposure time frames. In separate models, increasing levels in PM 2.5 , but not DBGT, were associated with rescue bronchodilator use. Conversely DBGT, but not PM 2.5 , had a significant association with FEV 1 . When DBGT and PM 2.5 exposures were placed in the same model, the strongest association between cumulative PM 2.5 exposures and the use of rescue bronchodilator was identified at the 0–24 hours (OR = 1.030; 95% CI = 1.012–1.049; p-value = 0.001) and 0–48 hours (OR = 1.030; 95% CI = 1.013–1.057; p-value = 0.001) prior to lung function measure. Conversely, DBGT exposure at 0 hours (β = 3.257; SE = 0.879; p-value>0.001) and 0–6 hours (β = 2.885; SE = 0.903; p-value = 0.001) hours before a reading were associated with FEV 1 . No significant interactions between DBGT and PM 2.5 were observed for rescue bronchodilator use or FEV 1 . Conclusions Short-term increases in PM 2.5 were associated with increased rescue bronchodilator use, while DBGT was associated with higher lung function (i.e. FEV 1 ). Further studies are needed to continue to elucidate the mechanisms of acute exposure to PM 2.5 and DBGT on lung function in asthmatics.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2019

Inverse regression for ridge recovery: a data-driven approach for parameter reduction in computer experiments

Parameter reduction can enable otherwise infeasible design and uncertainty studies with modern computational science models that contain several input parameters. In statistical regression, techniques for sufficient dimension reduction (SDR) use data to reduce the predictor dimension of a regression problem. A computational scientist hoping to use SDR for parameter reduction encounters a problem: a computer prediction is best represented by a deterministic function of the inputs, so data comprised of computer simulation queries fail to satisfy the SDR assumptions. To address this problem, here we interpret SDR methods sliced inverse regression (SIR) and sliced average variance estimation (SAVE) as estimating the directions of a ridge function, which is a composition of a low-dimensional linear transformation with a nonlinear function. Within this interpretation, SIR and SAVE estimate matrices of integrals whose column spaces are contained in the ridge directions’ span; we analyze and numerically verify convergence of these column spaces as the number of computer model queries increases. Moreover, we show example functions that are not ridge functions but whose inverse conditional moment matrices are low-rank. Consequently, the computational scientist should beware when using SIR and SAVE for parameter reduction, since SIR and SAVE may mistakenly suggest that truly important directions are unimportant.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Online peak-aware energy scheduling with untrusted advice

This paper studies the online energy scheduling problem in a hybrid model where the cost of energy is proportional to both the volume and peak usage, and where energy can be either locally generated or drawn from the grid. Inspired by recent advances in online algorithms with Machine Learned (ML) advice, we develop parameterized deterministic and randomized algorithms for this problem such that the level of reliance on the advice can be adjusted by a trust parameter. We then analyze the performance of the proposed algorithms using two performance metrics: robustness that measures the competitive ratio as a function of the trust parameter when the advice is inaccurate, and consistency for competitive ratio when the advice is accurate. Since the competitive ratio is analyzed in two different regimes, we further investigate the Pareto optimality of the proposed algorithms. Our results show that the proposed deterministic algorithm is Pareto-optimal, in the sense that no other online deterministic algorithms can dominate the robustness and consistency of our algorithm. Furthermore, we show that the proposed randomized algorithm dominates the Pareto-optimal deterministic algorithm. Our large-scale empirical evaluations using real traces of energy demand, energy prices, and renewable energy generations highlight that the proposed algorithms outperform worst-case optimized algorithms and fully data-driven algorithms.

Lee, Russell↗
DOE OSTI2018

Structural, Electronic, Magnetic, and Optical Properties of Half-Heusler Alloys RuMnZ (Z = P, As): a First-Principle Study

Half-Heusler alloys RuMnZ (Z = P, As ) are studied in the framework of Density Functional Theory (DFT). Structural, electronic, magnetic, and optical properties are calculated and analyzed using the WIEN2k simulation code. All the calculations are done using the full potential linearized augmented plane wave (FP-LAPW) method. Equilibrium lattice parameters are found to be in the range 5.5–5.6 Å. Band gaps of the compounds and density of states (DoS) analysis reveal that the minority spin-down states are semi-conducting while the majority spin-up states are conducting confirming the half-metallic nature of the compounds. Hence, at Fermi level, states are 100 % polarized. The value of the total magnetic moment is found to be 2, i.e., M{sub Tot} = 2μ{sub B}. Several optical properties, including dielectric function, reflectivity, refractive index, conductivity, and absorption coefficient are calculated as well. It is revealed from the imaginary part of the dielectric function that the compounds are optically metallic.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Determination of Carbon Functional Groups in Pyrolysis Bio-Oils using 13 C NMR: Laboratory Analytical Procedure (LAP)

Pyrolysis is a process that can be used to convert biomass to solid, liquid and gaseous products for use as renewable chemicals and fuels. The liquid fraction, known as “bio-oil” is complex and challenging to characterize, particularly by means of GC/MS, GPC, LC and FT-IR. NMR is capable of analyzing whole bio-oil samples and can provide quantitative results to characterize different functional groups or types of carbon present in bio-oil. This Laboratory Analytical Procedure (LAP) quantifies different carbon functional groups in whole bio-oil samples. This information can be used for comparisons between different pyrolysis experimental conditions or different upgrading processes and catalysts, and also allow for comparisons between bio-oils produced at different facilities.

09 BIOMASS FUELS↗
DOE OSTI2025

Bottomonium properties in the quark-gluon plasma from a lattice-QCD informed 𝑇-matrix approach

Recent computations of bottomonium correlation functions with extended sources in lattice-discretized quantum chromodynamics (lQCD) provide new insights into heavy-quark dynamics at distance scales which are of the order of the inverse temperature. We analyze these results employing the thermodynamic 𝑇-matrix framework, in a continued effort to interpret lQCD data for quarkonium correlation functions in a nonperturbative and self-consistently solved quantum-many-body approach to a strongly coupled quark-gluon plasma (QGP). Its key inputs are the in-medium driving kernel (potential) of the scattering equation and an interference function which implements 3-body effects in the quarkonium coupling to the thermal medium. A simultaneous description of lQCD results for the bottomonium correlators with extended operators and the previously analyzed Wilson line correlators only requires minor refinements of the potential but calls for stronger interference effects at larger separation of the bottom quark and antiquark. We then analyze the poles of the self-consistent 𝑇 matrices on the real axis to assess the survival of the various bound states. Here, we estimate the pertinent temperatures where the poles disappear for the various bottomonium states and discuss the relation to the corresponding peaks in the bottomonium spectral functions. We also recalculate the spatial diffusion coefficient of the QGP and find it to be similar to that in our previous study.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Comparative Density Functional Theory Study of Magnetic Exchange Couplings in Dinuclear Transition-Metal Complexes

Multicenter transition-metal complexes (MCTMs) with magnetically interacting ions have been proposed as components for information-processing devices and storage units. For any practical application of MCTMs as magnetic units, it is crucial to characterize their magnetic behavior, and in particular, the isotropic magnetic exchange coupling, J, between its magnetic centers. Due to the large size of typical MCTMs, density functional theory is the only practical electronic structure method for evaluating the J coupling. Here, we assess the accuracy of different density functional approximations for predicting the magnetic couplings of eight dinuclear transition-metal complexes, including five dimanganese, two dicopper, and one divanadium with known reliable experimental J couplings spanning from ferromagnetic to strong antiferromagnetic. The density functionals considered include global hybrid functionals which mix semilocal density functional approximations and exact exchange with a fixed admixing parameter, six local hybrid functionals where the admixing parameters are extended to be spatially dependent, the SCAN and r 2 SCAN meta-generalized gradient approximations (GGAs), and two widely used GGAs. We found that global hybrids tested in this work have a tendency to over-correct the error in magnetic coupling parameters from the Perdew–Burke–Ernzerhof (PBE) GGA as seen for manganese complexes. The performance of local hybrid density functionals shows no improvement in terms of bias and is scattered without a clear trend, suggesting that more efforts are needed for the extension from global to local hybrid density functionals for this particular property. The SCAN and r 2 SCAN meta-GGAs are found to perform as well as benchmark global hybrids on most tested complexes. We further analyze the charge density redistribution of meta-GGAs as well as global and local hybrid density functionals with respect to that of PBE, in connection to the self-interaction error or delocalization error.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Characterization of nuclear breakup as a function of hard-scattering kinematics using dijets measured by ATLAS in p+Pb collisions

This Letter analyzes the sensitivity of event geometry estimators to the initial-state kinematics of hard scattering in proton–lead collisions. This analysis uses dijets as a proxy for the parton–parton scattering configuration, correlating it with event geometry estimators, namely the energy deposited in the Zero-Degree Calorimeter and the transverse energy recorded in the Forward Calorimeter in the Pb-going direction. The analysis uses data recorded by the ATLAS detector at the Large Hadron Collider with a nucleon–nucleon center-of-mass energy of 8.16 TeV, corresponding to an integrated luminosity of 56 nb − 1 . The jets are measured within the pseudorapidity interval −2.8 < η < 4.5, where positive η values correspond to the direction of the proton beam. Results are presented as a function of the Bjorken-x of the parton originating from the proton, xp . Both event geometry estimators are found to be dependent on xp , with the energy deposited in the Zero-Degree Calorimeter about six times less sensitive to xp compared with the transverse energy deposited in the Forward Calorimeter.

Aad, G↗
DOE OSTI2023

Multielectrode electrochemical cell for in situ structural characterization of amorphous thin-film catalysts using high-energy X-ray scattering

A multielectrode-based electrochemical cell allows the structural characterization of an amorphous thin-film water oxidation catalyst under various electrochemical potentials using high-energy X-ray scattering and atomic pair distribution function (PDF) techniques. A multielectrode with five electrodes provides a sufficiently low background signal to enable high-energy X-ray scattering (HEXS) measurements and amplifies the extremely low HEXS signals from samples for high-resolution PDF analysis of in situ data from thin-film catalysts. Glassy carbon (GC) creates a relatively low intensity HEXS pattern and is used as a working electrode. Instead of a three-dimensional (3D) porous electrode architecture, the flat geometry of the electrode enables various deposition techniques to be used for the preparation of a highly conductive metal oxide layer. PDF analysis demonstrates high spatial resolution for a 230 nm thick amorphous iridium oxide film deposited on two roughened 60 µm thick GC electrodes. The PDF analysis resolves the domain size and distinguishes changes in fine structure which are directly correlated with the structure and function of the catalysts. In conclusion, the results bring the opportunity to analyze the structure of nanometre-scale amorphous thin-film catalysts in an electrolyte-compatible and compact 3D-printed electrochemical cell in a three-electrode configuration.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Genome-Wide Analysis of Terpene Synthase Gene Family in Mentha longifolia and Catalytic Activity Analysis of a Single Terpene Synthase

Terpenoids are a wide variety of natural products and terpene synthase (TPS) plays a key role in the biosynthesis of terpenoids. Mentha plants are rich in essential oils, whose main components are terpenoids, and their biosynthetic pathways have been basically elucidated. However, there is a lack of systematic identification and study of TPS in Mentha plants. In this work, we genome-widely identified and analyzed the TPS gene family in Mentha longifolia, a model plant for functional genomic research in the genus Mentha. A total of 63 TPS genes were identified in the M. longifolia genome sequence assembly, which could be divided into six subfamilies. The TPS-b subfamily had the largest number of genes, which might be related to the abundant monoterpenoids in Mentha plants. The TPS-e subfamily had 18 members and showed a significant species-specific expansion compared with other sequenced Lamiaceae plant species. The 63 TPS genes could be mapped to nine scaffolds of the M. longifolia genome sequence assembly and the distribution of these genes is uneven. Tandem duplicates and fragment duplicates contributed greatly to the increase in the number of TPS genes in M. longifolia. The conserved motifs (RR(X)8W, NSE/DTE, RXR, and DDXXD) were analyzed in M. longifolia TPSs, and significant differentiation was found between different subfamilies. Adaptive evolution analysis showed that M. longifolia TPSs were subjected to purifying selection after the species-specific expansion, and some amino acid residues under positive selection were identified. Furthermore, we also cloned and analyzed the catalytic activity of a single terpene synthase, MlongTPS29, which belongs to the TPS-b subfamily. MlongTPS29 could encode a limonene synthase and catalyze the biosynthesis of limonene, an important precursor of essential oils from the genus Mentha. This study provides useful information for the biosynthesis of terpenoids in the genus Mentha.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Universal trend of charge radii of even-even Ca–Zn nuclei

Radii of nuclear charge distributions carry information about the strong and electromagnetic forces acting inside the atomic nucleus. Whereas the global behavior of nuclear charge radii is governed by the bulk properties of nuclear matter, their local trends are affected by quantum motion of proton and neutron nuclear constituents. The measured differential charge radii δ$\langle$$r^{2}_{c}$$\rangle$ between neutron numbers N = 28 and N = 40 exhibit a universal pattern as a function of n = N – 28 that is independent of the atomic number. In this work, we analyze this remarkable behavior in even-even nuclei from calcium to zinc using two state-of-the-art theories based on quantified nuclear interactions: the ab initio coupled cluster theory and nuclear density functional theory. Both theories reproduce the smooth rise of differential charge radii and their weak dependence on the atomic number. By considering a large set of isotopic chains, we show that this trend can be captured by just two parameters: the slope and curvature of δ$\langle$$r^{2}_{c}$$\rangle$(n). We demonstrate that these parameters show appreciable model dependence, and the statistical analysis indicates that they are not correlated with any single model property, i.e., they are impacted by both bulk nuclear properties as well as shell structure.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Depth and microtopography influence microbial biogeochemical processes in a forested peatland

Background and aims: Peat-accumulating wetlands have undulating surfaces of raised areas (hummocks) and depressions (hollows). Hummock-hollow microtopography in relation to the water table influences the distribution of plant species, root density, and microbial community composition, which could in turn alter carbon (C) and nitrogen (N) cycling within peatlands. We used paired hummock and hollow cores from a boreal, forested peatland to assess how microtopography influences peatland microbial function and, in turn, ecosystem C and N cycling. Methods: The peat was analyzed for microbial biomass and potential enzyme activity in 10 cm depth increments relative to the water table, resulting in two increments for hollows and three for hummocks, which has a raised increment above the water table. Results: Across hummocks and hollows, microbial C and N and fungal biomass generally decreased with depth from the peat surface. In contrast, potential enzyme activity often increased with depth, but this varied within enzyme functional groups according to topography, depth, or both. The potential enzyme activity of C-N degrading peptidases, for example, differed across the five topography × depth increments with the lowest rate in the aerated hummocks. Hummocks compose approximately 66% of the land area at our study site and would therefore underestimate C turnover by an average of 25% if solely used to extrapolate patterns across a forested bog. Conclusion: In conclusion, our results suggest that asynchrony in C and N cycling across the undulating surface of forested peatlands impacts our ability to accurately predict biogeochemical cycling across this important ecosystem.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Kinetic simulations of ignited mode cesium vapor thermionic converters

Cesium vapor thermionic converters are an attractive method of converting high-temperature heat directly to electricity, but theoretical descriptions of the systems have been difficult due to the multi-step ionization of Cs through inelastic electron–neutral collisions. This work presents particle-in-cell simulations of these converters, using a direct simulation Monte Carlo collision model to track 52 excited states of Cs. Here, these simulations show the dominant role of multi-step ionization, which also varies significantly based on both the applied voltage bias and pressure. The electron energy distribution functions are shown to be highly non-Maxwellian in the cases analyzed here. A comparison with previous approaches is presented, and large differences are found in ionization rates due especially to the fact that previous approaches have assumed Maxwellian electron distributions. Finally, an open question regarding the nature of the plasma sheaths in the obstructed regime is discussed. The one-dimensional simulations did not produce stable obstructed regime operation and thereby do not support the double-sheath hypothesis.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Accurate and Data‐Efficient Micro X‐ray Diffraction Phase Identification Using Multitask Learning: Application to Hydrothermal Fluids

Traditional analysis of highly distorted micro X‐ray diffraction (μ‐XRD) patterns from hydrothermal fluid environments is a time‐consuming process, often requiring substantial data preprocessing and labeled experimental data. Herein, the potential of deep learning with a multitask learning (MTL) architecture to overcome these limitations is demonstrated. MTL models are trained to identify phase information in μ‐XRD patterns, minimizing the need for labeled experimental data and masking preprocessing steps. Notably, MTL models show superior accuracy compared to binary classification convolutional neural networks. Additionally, introducing a tailored cross‐entropy loss function improves MTL model performance. Most significantly, MTL models tuned to analyze raw and unmasked XRD patterns achieve close performance to models analyzing preprocessed data, with minimal accuracy differences. This work indicates that advanced deep learning architectures like MTL can automate arduous data handling tasks, streamline the analysis of distorted XRD patterns, and reduce the reliance on labor‐intensive experimental datasets.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Enhancing Early Systems R&D Capabilities with Systems —Theoretic Process Analysis

Systems engineering today faces a wide array of challenges, ranging from new operational environments to disruptive technological — necessitating approaches to improve research and development (R&D) efforts. Yet, emphasizing the Aristotelian argument that the “whole is greater than the sum of its parts” seems to offer a conceptual foundation creating new R&D solutions. Invoking systems theoretic concepts of emergence and hierarchy and analytic characteristics of traceability, rigor, and comprehensiveness is potentially beneficial for guiding R&D strategy and development to bridge the gap between theoretical problem spaces and engineering-based solutions. In response, this article describes systems–theoretic process analysis (STPA) as an example of one such approach to aid in early-systems R&D discussions. STPA—a ‘top-down’ process that abstracts real complex system operations into hierarchical control structures, functional control loops, and control actions—uses control loop logic to analyze how control actions (designed for desired system behaviors) may become violated and drive the complex system toward states of higher risk. By analyzing how needed controls are not provided (or out of sequence or stopped too soon) and unneeded controls are provided (or engaged too long), STPA can help early-system R&D discussions by exploring how requirements and desired actions interact to either mitigate or potentially increase states of risk that can lead to unacceptable losses. This article will demonstrate STPA's benefit for early-system R&D strategy and development discussion by describing such diverse use cases as cyber security, nuclear fuel transportation, and US electric grid performance. Together, the traceability, rigor, and comprehensiveness of STPA serve as useful tools for improving R&D strategy and development discussions. In conclusion, leveraging STPA as well as related systems engineering techniques can be helpful in early R&D planning and strategy development to better triangulate deeper theoretical meaning or evaluate empirical results to better inform systems engineering solutions.

42 ENGINEERING↗
DOE OSTI2024

ReactionMechanismSimulator.jl: A modern approach to chemical kinetic mechanism simulation and analysis

Abstract We present ReactionMechanismSimulator.jl (RMS), a modern differentiable software for the simulation and analysis of chemical kinetic mechanisms, including multiphase systems. RMS has already been applied to problems in combustion, pyrolysis, polymers, pharmaceuticals, catalysis, and electrocatalysis. RMS is written in Julia, making it easy to develop and allowing it to take advantage of Julia's extensive numerical computing ecosystem. In addition to its extensive library of optimized analytic Jacobians, RMS can generate and use Jacobians computed using automatic differentiation and symbolically generated analytic Jacobians. RMS is demonstrated to be faster than Cantera and Chemkin in several benchmarks. RMS also implements an extensive set of features for analyzing chemical mechanisms, including a library of easy‐to‐call plotting functions, molecular structure resolved flux diagram generation, crash analysis, traditional sensitivity analysis, transitory sensitivity analysis, and an automatic mechanism analysis toolkit. RMS implements efficient adjoint and parallel forward sensitivity analyses. We also demonstrate the ease of adding new features to RMS.

Johnson, Matthew S.↗