Search NASA⌕ Search

SEARCH · Search NASA

Results for “composite optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Enhanced thermoelectric performance in Cu-intercalated BiTeI by compensation weakening induced mobility improvement

The low weighted carrier mobility has long been considered to be the key challenge for improvement of thermoelectric (TE) performance in BiTeI. The Rashba-effect-induced two-dimensional density of states in this bulk semiconductor is beneficial for thermopower enhancement, which makes it a prospective compound for TE applications. In this report, we show that intercalation of minor Cu-dopants can substantially alter the equilibria of defect reactions, selectively mediate the donor-acceptor compensation, and tune the defect concentration in the carrier conductive network. Consequently, the potential fluctuations responsible for electron scattering are reduced and the carrier mobility in BiTeI can be enhanced by a factor of two to three between 10 K and 300 K. The carrier concentration can also be optimized by tuning the Te/I composition ratio, leading to higher thermopower in this Rashba system. Cu-intercalation in BiTeI gives rise to higher power factor, slightly lower lattice thermal conductivity, and consequently improved figure of merit. Compared with pristine BiTe 0.98 I 1.02 , the TE performance in Cu 0.05 BiTeI reveals a 150% and 20% enhancement at 300 and 520 K, respectively. Ultimately, these results demonstrate that defect equilibria mediated by selective doping in complex TE and energy materials could be an effective approach to carrier mobility and performance optimization.

36 MATERIALS SCIENCE↗

Thermomechanical design optimization for low metal footprint in hybrid metal-polymer heat exchanger

Material and maintenance costs of metal-based heat exchangers surpass profits in waste heat recovery (WHR) from ultra-low temperature (<100C) sources [1]. A low-cost alternative like polymer pipes suffer from poor thermal conductivity (~0.2 W/mK), and a low overall heat transfer coefficient. Polymers’ thermal conductivity have previously been enhanced through systematic molecular alignment by stretching [2], chemical vapor deposition of extended polymers [3], surface grating [4], etc. However, these approaches suffer from scalability issues for WHR heat exchangers in terms of cost [3], and thermomechanical considerations [5]. In this work, we propose novel hybrid metal-polymer heat exchangers that are made from polymer-copper strips. Through finite element method (FEM) simulations, we first optimize the placement of copper around polymer strips to enhance the transverse thermal conductivity of the strips. The copper cladded polymer strips are wound helically in a roll-to-roll system to form the pipes for a heat exchanger. We then optimize the design of helically wound pipes to reduce thermomechanical strains to < 0.2 % at 100C and 40 psi working conditions. At 25 % volume fraction of copper in the pipe, we predict up to 20 % enhancement in overall heat transfer from a base polymer with a thermal conductivity of 0.2 W/mK. We also compare and contrast the thermomechanical performance of the optimized metal-polymer strips to random metal matrix composites. Finally, we experimentally verify the thermal conductivity of the optimized strips through bulk thermal conductivity and thermal interface resistance measurement setup. By systematically improving the design through FEM and experimental measurements, we provide an optimized design of hybrid metal-polymer pipes that provides a low metal footprint and cost-effective means for harvesting waste heat from ultra-low temperature sources. Thekdi, Arvind, and Sachin U. Nimbalkar. Oak Ridge National Lab, 2015 Shen, Sheng, et al. Nature nanotechnology 5.4 (2010): 251. Xu, Yanfei, et al. Science advances 4.3 (2018): 3031. Smith, M. K., Singh, V., Kalaitzidou, K., & Cola, B. A. (2015). ACS nano, 9(2), 1080-1088. Aymonier, C., Bortzmeyer, D., Thomann, R., & M&uuml;lhaupt, R. (2003). Chemistry of Materials, 15(25), 4874-4878.

C Rajagopal, Manjunath↗

Micropolar deep material network

This study extends the Deep Material Network (DMN), a physics-informed machine learning framework, to predict the homogenized mechanical response of composite materials with micropolar (Cosserat-type) constitutive behavior. This extension incorporates microstructure-dependent size effects, enabling accurate, efficient, and size-aware predictions for composites with complex internal architectures. While traditional, direct numerical simulation micropolar models effectively capture size effects by introducing extra local degrees of freedom, they bring significant computational challenges, particularly for multiscale analyses relevant to engineering applications. The micropolar DMN developed in this paper achieves high accuracy while significantly reducing computation time compared to micropolar direct numerical simulations. This advancement enables multiscale analyses and parameter studies that were previously impractical, such as high-cycle fatigue simulations and comprehensive investigations of internal length scale effects notably in size-dependent plastic response and the optimization of lattice structures. By uniting microstructure-sensitive modeling, physics-driven learning, and scalable surrogate modeling, the micropolar DMN paves the way for accelerated material design, large-scale parametric studies, and the reliable incorporation of size-dependent effects across a wide range of engineering applications, including optimization and next-generation composite design.

36 MATERIALS SCIENCE↗

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites. Topical Report

This project aimed to integrate, optimize, and validate the fiber orientation and length distribution models previously developed and implemented in the Autodesk® Simulation Moldflow® Insight (ASMI) software package for injection-molded long-carbon-fiber (LCF) thermoplastic composite structures. The project was organized into two phases. Phase 1 demonstrated the ability of the advanced ASMI package to predict fiber orientation and length distributions in LCF/polypropylene (PP) and LCF/polyamide-6, 6 (PA66) plaques within 15% of experimental results. Phase 2 validated the advanced ASMI package by predicting fiber orientation and length distributions within 15% of experimental results for a complex three-dimensional (3D) Toyota automotive part injection-molded from LCF/PP and LCF/PA66 materials. Work under Phase 2 also included estimate of weight savings and cost impacts for a vehicle system using ASMI and structural analyses of the complex part. The present report summarizes the completion of Phases 1 and 2 work activities and accomplishments achieved by the team comprising Pacific Northwest National Laboratory (PNNL); Purdue University (Purdue); Virginia Polytechnic Institute and State University (Virginia Tech); Autodesk, Inc. (Autodesk); PlastiComp, Inc. (PlastiComp); Toyota Research Institute North America (Toyota); Magna Exteriors and Interiors Corp. (Magna); and University of Illinois. Figure 1 illustrates the technical approach adopted in this project that progressed from compounding LCF/PP and LCF/PA66 materials, to process model improvement and implementation, to molding and modeling LCF/PP and LCF/PA66 plaques. The lessons learned from the plaque study and the successful validation of improved process models for fiber orientation and length distributions for these plaques enabled the project to go to Phase 2 to mold, model, and optimize the 3D complex part.

42 ENGINEERING↗

Critical role of solvation on CC13 porous organic cages for design of porous liquids

Efficient carbon capture requires the design of new materials with high CO 2 selectivity and gas adsorption capacity that can be incorporated into existing industrial processes. Porous liquids (PLs) are promising candidate materials that consist of a nanoporous host and a solvent forming a liquid with permanent porosity based on exclusion of the solvent from the interior of the nanoporous host. Stable PLs are based on solvent-nanoporous host interactions, which can be evaluated through molecular simulations. Here, time- and temperature-dependent density functional theory simulations were performed between four solvents, 2-bromophenol, 4-methylphenol, 2,4-dimethylphenol, and cyclohexanone and the CC13 porous organic cage (POC) as a prototypical PL composition. Overall, minimal reactions occurred in the PL including no changes in the POC structure. Additionally, POC-solvent coordination occurred through interactions of neighboring functional groups such as methyl/bromide and hydroxyl on the solvent molecules with the POC surface. Therefore, the location rather than the number of functional groups on the solvent molecule controls the POC-solvent interactions. Additionally, the POC pore window contracted or expanded up to 8% during solvation, which correlates with the experimental solubility and static solvent-POC binding, where solvents that caused less contraction of the POC pore window increased POC solubility. Finally, these results allow for the design of optimized POC-based PL compositions based on solvent-nanoporous host binding and variation in the pore window during solvation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Co-Optimization of Fuels & Engines (Co-Optima) Initiative: Recent Progress on Light-Duty Boosted Spark-Ignition Fuels/Engines

This presentation reports recent progress on light-duty boosted spark-ignition fuels/engines being developed under the Co-Optimization of Fuels and Engines initiative (Co-Optima). Co-Optima is focused on identifying fuel properties that optimize engine performance, independent of composition, allowing the market to define the best means to blend and provide these fuels. However, in support of this, we are pursuing a systematic study of blendstocks to identify a broad range of feasible options, with the objective of identifying blendstocks that can provide target ranges of key fuel properties, identifying trade-offs on consistent and comprehensive basis, and sharing information with stakeholders.

33 ADVANCED PROPULSION SYSTEMS↗

Development of integrated screening, cultivar optimization, and verification research (DISCOVR): A coordinated research-driven approach to improve microalgal productivity, composition, and culture stability for commercially viable biofuels production

To address major knowledge gaps and barriers to the commercial development of algal biomass for biofuels and co-products, a collaborative consortium, Development of Integrated Screening, Cultivar Optimization, and Verification Research (DISCOVR), was established in 2016. Funded by the U.S. Department of Energy (DOE) Bioenergy Technologies Office (BETO), this consortium constitutes a partnership between four DOE national laboratories - Pacific Northwest National Laboratory (PNNL), Los Alamos National Laboratory (LANL), the National Renewable Energy Laboratory (NREL), and Sandia National Laboratories (SNL) - and the Arizona Center for Algae Technology and Innovation (AzCATI) at Arizona State University. To address the barriers of strain selection for achieving high seasonal productivities with a suitable composition and culture resilience, a tiered strain down-selection pipeline is implemented. At Tier I, the temperature and salinity tolerance of strains is determined in flask cultures; at Tier II, the areal biomass productivity and composition is determined in climate-simulation photobioreactors; at Tier III, the productivity and culture stability are determined in outdoor raceways. The top performing strains move forward to long-term testing at the algae testbed site at AzCATI to generate annual biomass productivity data. Concurrent to the strain down-selection in the DISCOVR pipeline, hypotheses for increasing biomass productivity, shifting biomass composition to enhance intrinsic value, and improving culture stability and resistance to pests are also tested. Techno-economic analyses are carried out to determine whether promising findings from laboratory studies or proposed modifications in outdoor pond cultivation conditions translate into reductions in the minimum biomass selling price (MBSP). Notably, in the three years following the launch of DISCOVR, annual biomass productivity has increased from 11.7 to 17.6 g m -2 day -1 , resulting in an MBSP decrease from 824 to 611 $ ton -1 .

09 BIOMASS FUELS↗

Near-UV and blue wavelength excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} high efficiency red phosphors

Red phosphors with narrow emission around 615 nm (with FWHM~5–10 nm) having chemical compositions of A{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} (A=Mg, Sr) have been found to exhibit the highest luminescence amongst the molybdate–tungstate family when excited by sources in the 380–420 nm wavelength range. Thus they are most suitable for enhancing color rendering index and lowering color temperature in phosphor converted white LEDs (pc-WLEDs) with near-UV/blue LED excitation sources. The excitation band edge in the near UV/blue wavelength in the reported phosphor has been attributed to the coordination environment of the transition metal ion (Mo{sup 6+}, W{sup 6+}) and host crystal structure. Furthermore the quantum efficiency of the phosphors has been enhanced by adjusting activator concentration, suitable compositional alloying using substitutional alkaline earth metal cations and charge compensation mechanisms. - Graphical abstract: The charge transfer excitation of orthorhombic Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} is significantly higher than tetragonal CaMoO{sub 4}: Eu{sup 3+} phosphors making Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} prime candidates for fabrication of warm white phosphor-converted LEDs. - Highlights: • LED excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} phosphors were synthesized. • These phosphors are 10 times more intense than CaMoO{sub 4}: Eu{sup 3+} red phosphors. • Their intensity and efficiency were enhanced by materials optimization techniques. • Such techniques include compositional alloying, charge compensation, etc.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Robust Solar Receivers Using MAX Phase Materials

This work was supported by the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy under the Solar Energy Technologies Office Award Number 35928. The objective of the proposed effort was to develop and optimize additive manufacturing technologies for low-cost fabrication of high-temperature receivers using MAX phase-based materials (Ti 3 SiC 2 and Ti 3 AlC 2 ). MAX phase materials are a group of ternary metal carbides and nitrides where M stands for an early transition metal element, A is a group 13–16 element, and X is C and/or N. In Phase 1, the binder jetting additive manufacturing process was used to synthesize and characterize the Ti 3 SiC 2 MAX phase material. The typical process involved first producing a TiC preform using binder jetting followed by infiltration of the preform with silicon melt to form Ti 3 SiC 2 in situ. The reaction-infiltrated samples showed formation of MAX phase in the sample core; however, the surface showed cracking. Various process conditions—cooling rates, hold times, Si proportion, etc.—were varied to minimize the surface cracking. The fabricated MAX phase core was characterized by microstructure analysis and evaluations of mechanical properties such as hardness and thermal shock. In Phase 2, the focus included fabrication of Ti 3 SiC 2 MAX phase materials by spark plasma sintering (SPS) and synthesis of Ti 3 AlC 2 MAX phase materials by the Al melt infiltration process. It is expected that Al infiltration will not cause sample cracking, since Al does not expand during solidification. In addition, other processing approaches were investigated to fabricate the MAX phase materials, such as SPS with a graphite bedding approach for producing short-length Ti 3 AlC 2 MAX phase tubes for demonstration of prototypical Concentrating Solar Power receiver tubes. Fabricated samples underwent thermo-mechanical testing to validate the materials for the solar receiver application at temperatures >1000°C. In Phase 3, the effort focused on the development and optimization of the Ti-Al-C MAX phase composite material using the Al melt infiltration approach. We started with optimization of precursor powders and making preform structures by either pressing them in a die or using the binder jetting additive manufacturing process followed by Al melt infiltration. In addition, we investigated the formation of preform structures by cold isostatic pressing followed by Al melt infiltration for making Ti-Al-C MAX phase composite. Thermo-mechanical characterizations, such as creep, strength, and thermal shock, were conducted to establish the structures’ performance.

36 MATERIALS SCIENCE↗

Enhancing lithium storage performance of bimetallic oxides anode by synergistic effects

Spinel bimetallic transition metal oxide anode such as ZnMn 2 O 4 , has drawn increasing interest due to attractive bimetal interaction and high theoretical capacity. While it suffers from huge volume expansion and poor ionic/electronic conductivity. Nanosizing and carbon modification can alleviate these issues, while the optimal particle size within host is unclear yet. We here propose an in-situ confinement growth strategy to fabricate pomegranate-structured ZnMn 2 O 4 nanocomposite with calculated optimal particle size in mesoporous carbon host. Theoretical calculations reveal favorable interatomic interactions between the metal atoms. Further, by the synergistic effects of structural merits and bimetal interaction, the optimal ZnMn 2 O 4 composite achieves greatly improved cycling stability (811 mAh g -1 at 0.2 A g -1 after 100 cycles), which can maintain its structural integrity upon cycling. X-ray absorption spectroscopy analysis further confirms delithiated Mn species (Mn 2 O 3 but little MnO). Briefly, this strategy brings new opportunity to ZnMn 2 O 4 anode, which could be adopted to other conversion/alloying-type electrodes.

25 ENERGY STORAGE↗

Process Control Approach to Implement High Waste Loading Glass Formulations for Hanford Low Activity Waste Vitrification - 18435

Acceptable glass formulations for vitrification of Hanford low activity waste (LAW) at The Hanford Tank Waste Treatment and Immobilization Plant (WTP) must meet a variety of product quality, processability, and waste loading requirements. The glass formulation development work underpinning the WTP baseline LAW glasses was captured in a vitrification process control approach developed by the Vitreous State Laboratory (VSL) and Atkins Energy Federal EPC, Inc. that permits the calculation of the glass formulation required for each particular batch of LAW delivered to the LAW vitrification facility. Since that time, we have developed a wide range of glass formulations that achieve considerably higher waste loadings and which therefore are more economically attractive in terms of reduced amounts of glass produced and decreased time for treatment. That work was done in support of the Department of Energy's Office of River Protection program that is examining options to optimize the LAW facility and LAW glass waste form. Implementation of these high waste loading formulations at the WTP requires the development of a new LAW vitrification process control algorithm, which is the subject of this paper. Waste loadings in LAW glasses are typically limited by either the alkali loading for LAW with low sulfate content or the SO{sub 3} loading for LAW with high sulfate content. In the former case, waste loadings are limited by refractory corrosion and glass corrosion on the vapor hydration test (VHT) and product consistency test (PCT), all of which tend to increase with higher alkali concentrations. In the latter case, waste loadings are limited by the formation of a molten sulfate phase in the melter, which has deleterious effects. The LAW vitrification process control strategy must mitigate these effects while optimizing waste loadings. Given the composition of any LAW stream, the new LAW vitrification process control algorithm permits the calculation of a suitable high waste loading glass composition and the required glass forming additives such that all processing, waste loading, and product quality requirements are met. This algorithm was developed from data for a large number of glasses that were formulated, and characterized with respect to a variety of properties affecting processability and product quality; many of these formulations were also subjected to melter testing to verify acceptable processing characteristics, processing rates, and the absence of secondary sulfate phase formation. This paper describes the development of the present algorithm, comparisons to the present lower waste loading baseline WTP process control approach, and plans for further development and testing. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Carbon nanofibers (CNFs) dispersed in ultra-high performance concrete (UHPC): Mechanical property, workability and permeability investigation

This paper presents experimental data on the effect of carbon nano-fiber (CNF) dispersion on mechanical behavior, workability, and permeability of ultra-high-performance concrete containing CNF (UHPC-CNF). The addition of CNFs in concrete has been shown to provide improved performance. However, an inhomogeneous distribution of CNFs in the cement matrix can result in no impact or decreased mechanical performance. Due to the van der Waal's forces and hydrophobic surface properties of the CNFs, good dispersion in mix fluids and cement paste is challenging. Experimental studies of UHPC-CNF with different dispersion methods are provided. Further mixing with optimized UHPC paste allowed for the investigation of the optimal dosage of CNFs, impact on porosity, compressive strength, flexural strength, hydration rate, and slump. Scanning electron microscopy (SEM) analysis visually revealed the effect of dispersion. Our results indicate that shear mixing and subsequent ultrasonic dispersion with chemical surfactants can provide a well-dispersion liquid admixture of CNFs resulting in high mechanical performance of UHPC-CNFs composites. The water permeability and chloride resistance of optimized UHPC-CNFs composites were further evaluated with the wicking test and ponding test to reveal improved performance for these properties as well.

36 MATERIALS SCIENCE↗

Design of a Composite Membrane with Patches

This paper is concerned with minimization and maximization problems of eigenvalues. The principal eigenvalue of a differential operator is minimized or maximized over a set which is formed by intersecting a rearrangement class with an affine subspace of finite co-dimension. A solution represents an optimal design of a 2-dimensional composite membrane {Omega}, fixed at the boundary, built out of two different materials, where certain prescribed regions (patches) in {Omega} are occupied by both materials. We prove existence results, and present some features of optimal solutions. The special case of one patch is treated in detail.

97 MATHEMATICS AND COMPUTING↗

An Investigation into the Effects of Process Conditions on the Tribological Performance of Pack Carburized Titanium with Limited Oxygen Diffusion

In the present study, a new pack carburization technique for titanium has been investigated. The aim of this treatment is to produce a titanium carbide/oxycarbide layer atop of an extended oxygen diffusion zone [α-Ti(O)]. The effects of treatment temperature and pack composition have been investigated in order to determine the optimal conditions required to grant the best tribological response. The resulting structural features were investigated with particular interest in the carbon and oxygen concentrations across the samples cross section. The optimization showed that a temperature of 925 °C with a pack composition of 1 part carbon to 1 part energizer produced surface capable of withstanding a contact pressure of ≈ 1.5 GPa for 1 h. The process resulted in TiC surface structure which offers enhanced hardness (2100 HV) and generates a low friction coefficient (μ ≈ 0.2) when in dry sliding contact with an alumina (Al{sub 2}O{sub 3}) ball. The process also produced an extended oxygen diffusion zone that helps to improve the load bearing capacity of the substrate.

36 MATERIALS SCIENCE↗

Status Report on the Fabrication of Fuel Cladding Chemical Interaction Test Articles for ATR Irradiations

FeCrAl alloys are a promising new class of alloys for light water reactor (LWR) applications due to their superior oxidation and corrosion resistance in high temperature environments. The current R&D efforts have focused on the alloy composition and processing routes to generate nuclear grade FeCrAl alloys with optimized properties for enhanced accident tolerance while maintaining properties needed for normal operation conditions. Therefore, the composition and processing routes must be optimized to maintain the high temperature steam oxidation (typically achieved by increasing the Cr and Al content) while still exhibiting properties conducive to normal operation in a LWR (such as radiation tolerance where reducing Cr content is favorable). Within this balancing act is the addition of understanding the influence on composition and processing routes on the FeCrAl alloys for fuel-cladding chemical interactions (FCCI). Currently, limited knowledge exists on FCCI for the FeCrAl-UO 2 clad-fuel system. To overcome the knowledge gaps on the FCCI for the FeCrAl-UO2 clad-fuel system a series of fueled irradiation tests have been developed for irradiation in the Advanced Test Reactor (ATR) housed at the Idaho National Laboratory (INL). The first series of tests has already been reported. These tests used miniaturized 17x17 PWR fuel geometry rodlets of second-generation FeCrAl alloys fueled with industrial Westinghouse UO 2 fuel. These rodlets were encapsulated within a stainless steel housing.To provide high fidelity experiments and more robust testing, a new series of rodlets have been developed deemed the Accident Tolerant Fuel Experiment #1 Oak Ridge National Laboratory FCCI test (ATF-1 ORNL FCCI). The main driving factor, which is discussed in detail, was to provide a radiation environment where prototypical fuel-clad interface temperatures are met while still maintaining constant contact between industrial fuel and the candidate cladding alloys, hence promoting FCCI between the fuel-clad systems. The other factor was to develop a test bed where multiple candidate alloys could be evaluated within a single irradiation test train, thereby reducing overall costs and increasing efficiency in alloy screening efforts. A collaboration between ORNL and INL was developed to facilitate the completion of the test bed for FCCI testing. The report highlights the activities related to the development of the ATF-1 ORNL FCCI rodlets for irradiation in INL’s ATR as part of the on-going ATF-1 experiments.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Synthesis and Characterization of MoNb Films Superconducting at 100-200 mK

We have developed a new transition-edge sensor material with critical temperature (T-c) in the range 100-200 mK. The new material is a solid solution of two superconducting components, MoxNb1-x, co-sputtered from two high-purity single-component targets (Mo and Nb). The T-c has a minimum (dT(c)/dx = 0) at an intermediate concentration of the components. We have optimized the deposition parameters and composition to provide films with a sharp superconducting transition at ~ 150 mK. We investigated structural features of the films and surface morphology using X-ray diffraction (XRD) and scanning electron microscopy. The XRD measurements indicate that the grown films are polycrystalline, with a preferred orientation along the (110) crystal direction and a clear correlation between superconducting properties and film microstructure.

superconducting alloys↗

Highly Efficient Removal of Lead Ions from Aqueous Solutions Using Chitosan/Rice Husk Ash/Nano Alumina with a Focus on Optimization by Response Surface Methodology: Isotherm, Kinetic, and Thermodynamic Studies

In the present study, an adsorbent named chitosan/rice husk ash/nano-γ alumina was prepared and used for the removal of lead ions from aqueous solutions. It was characterized by FESEM, FTIR, XRD, and BET. The important and interactive effects of some considered parameters, such as the initial lead ion concentration, pH, adsorbent mass and contact time, were estimated and optimized by using the central composite design (CCD). The Maximum adsorption efficiency of lead ions under optimum conditions, including the pH of 5, adsorbent mass of 0.01 g, the initial lead ion concentration of 30 ppm, and the contact time of 105 min, was achieved to be 90.98%. The adsorption kinetic was consistent with the pseudo-second-order model (R{sup 2} = 0.9967). The lead adsorption isotherms were well fitted to the Langmuir model, indicating the maximum adsorption capacity of 181.82 mg g{sup −1}. Thermodynamic parameters (R{sup 2}: 0.9200, ΔH°: − 22871.81 kJ mol{sup −1}, ΔG{sup °}: − 10.63 kJ mol{sup −1}, and ΔS{sup °}: 118.37 kJ mol{sup −1} K{sup −1}) were calculated and indicating adsorption process was exothermic and spontaneous in the temperature range of 283.15–313.15 k. The maintenance above 70% capacity of the adsorbent was observed by the regeneration study of chitosan/rice husk ash/nano-γ alumina after six cycles. Comparison of adsorption efficiency of the studied adsorbent and other adsorbents in the removal of lead ions was also done in this paper. Consequently, the excellent properties of the presented nanocomposite could make it an ideal adsorbent for the removal of lead ions from aqueous solutions. Graphical Abstract: .

77 NANOSCIENCE AND NANOTECHNOLOGY↗