Search NASA⌕ Search

SEARCH · Search NASA

Results for “matrix diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Microstructure investigations of temperature effect on Al-UMo diffusion couples irradiated by swift Xe ions

Post-irradiation examination (PIE) results of microstructure in irradiated Al-UMo diffusion couples are reported here. These diffusion couples were irradiated by 60 MeV Xe ions at four different temperatures up to approximately 5.5 × 10 17 ions/cm 2 peak ion fluence. An Al-UMo interaction layer (IL) was found to form at all four investigated temperatures. The IL is homogeneously amorphous when formed up to 150 °C. At 215 °C, the (U,Mo)Al 3 nanocrystalline precipitates form within the amorphous IL matrix. Kirkendall voids with prominent temperature dependence were observed in both the Al layer and its interface with the IL. On the other hand, Xe bubbles were found to form in UMo and Al-UMo IL with different morphology. These microstructure features were quantitatively measured and are reported to provide valuable references for understanding the irradiation behavior of UMo/Al dispersion fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Increasing M 2 (dobdc) Loading in Selective Mixed-Matrix Membranes: A Rubber Toughening Approach

Mixed-matrix membranes (MMMs) were formed by incorporating M 2 (dobdc) (M = Mg, Ni; dobdc 4– = 2,5-dioxido-1,4-benzenedicarboxylate) metal–organic framework (MOF) nanoparticles in a series of poly(ether-imide) copolymers. Addition of the MOF nanoparticles improved the permeability of H 2 , N 2 , CH 4 , and CO 2 relative to the pure copolymer by increasing gas solubility and, in most cases, diffusivity. More limited improvements in diffusivity were observed for the more strongly adsorbing gases. Because of such transport considerations, improvements in permeability and selectivity were most pronounced for H 2 /CH 4 and H 2 /N 2 separations. Incorporation of a greater ether content within the copolymers led to the formation of defect-free MMMs by physically sealing polymer–MOF interfacial defects, allowing higher MOF loadings to be achieved. For Mg 2 (dobdc), selective, defect-free films could be formed with loadings of up to 51 wt %. However, at these high loadings, films became weak and brittle. The mechanical properties of the composite materials were therefore quantified by tensile tests and compared to those of the neat polymers used commercially for membrane film formation. High contents of flexible ether units and small MOF nanoparticle sizes were found to be necessary to form strong and ductile MMMs, although clear trade-offs exist between transport performance, MOF loading, and mechanical properties. In conclusion, these trade-offs are critically examined to evaluate the current limitations and potential benefits to forming M 2 (dobdc) MMMs using this rubber toughening approach.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Dehydration of multilamellar fatty acid membranes: Towards a computational model of the stratum corneum

The level of hydration controls the cohesion between apposed lamellae of saturated free fatty acids found in the lipid matrix of stratum corneum, the outermost layer of mammalian skin. This multilamellar lipid matrix is highly impermeable to water and ions, so that the local hydration shell of its fatty acids may not always be in equilibrium with the acidity and relative humidity, which significantly change over a course of days during skin growth. The homeostasis of the stratum corneum at each moment of its growth likely requires a balance between two factors, which affect in opposite ways the diffusion of hydrophilic species through the stratum corneum: (i) an increase in water order as the lipid lamellae come in closer contact, and (ii) a decrease in water order as the fraction of charged fatty acids is lowered by pH. Herein molecular dynamics simulations are employed to estimate the impact of both effects on water molecules confined between lamellae of fatty acids. Under conditions where membrane undulations are energetically favorable, the charged fatty acids are able to sequester cations around points of contact between lamellae that are fully dehydrated, while essentially maintaining a multilamellar structure for the entire system. This observation suggests that the undulations of the fatty acid lamellae control the diffusion of hydrophilic species through the water phase by altering the positional and rotational order of water molecules in the embedded/occluded “droplets.”

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Embedded Ge nanocrystals in SiO{sub 2} synthesized by ion implantation

200 nm thick SiO{sub 2} layers grown on Si substrates were implanted with 150 keV Ge ions at three different fluences. As-implanted samples were characterized with time-of-flight secondary ion mass spectrometry and Rutherford backscattering spectrometry to obtain depth profiles and concentration of Ge ions. As-implanted samples were annealed at 950 °C for 30 min. Crystalline quality of pristine, as-implanted, and annealed samples was investigated using Raman scattering measurements and the results were compared. Crystalline structure of as-implanted and annealed samples of embedded Ge into SiO{sub 2} matrix was studied using x-ray diffraction. No secondary phase or alloy formation of Ge was detected with x-ray diffraction or Raman measurements. Scanning transmission electron microscope measurements were done to get the nanocrystal size and localized information. The results confirmed that fluence dependent Ge nanocrystals of different sizes are formed in the annealed samples. It is also observed that Ge is slowly diffusing deeper into the substrate with annealing.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Development and Demonstration of an In-Situ Tritium Scavenger

The objective of this project was to use an inherent feature of salt-cooled reactors towards the capture and removal of tritium from the primary coolant system: the presence of the graphite moderator. The fuel elements fluoride-salt cooled high-temperature (FHR) reactors consist of a graphite matrix that encapsulates TRISO fuel particles, and the total fuel element surface area of Mark I PB-FHR is 7780 m 2 . Therefore the FHR fuel inherently provides removable graphite of high surface area. The goal of this project was to understand the transport of tritium across the salt-graphite interface. The following was achieved: 1. Electrochemical techniques were demonstrated for studying the entry, diffusion, and trapping of hydrogen isotopes in graphite. 2. Electrochemical techniques were used to demonstrate the relationship between galvanic corrosion between graphite and stainless steel 316 and hydrogen uptake in graphite. 3. Electrochemical techniques were demonstrated for studying the dissolution and diffusion of hydrogen isotopes in molten FLiBe. 4. Thermodynamic reference electrodes were tested for FLiBe and FLiNaK. 5. Electrochemical techniques were demonstrated as an in-salt hydrogen thermal desorption measurement, which had previously only been achieved in gas environments. 6. FLiBe exposure of graphite lead to graphite fluorination and an increase of defects, which indicate an increase of reactive carbon sites available for tritium uptake. 7. TRIDENT modeling was used to perform sensitivity analysis of FHR design parameters on tritium uptake fraction in graphite, showing high sensitivity to tritium diffusivity and solubility. 8. A cross-cutting effort with another NEUP-funded project was initiated for application of the SAM mass-transport module to system-scale tritium modeling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Understanding grain boundary segregation under irradiation: A mesoscale modeling study

Grain boundaries (GBs) are an important component in the design of irradiation resistant materials as they play a crucial role as point defect sinks for non-equilibrium vacancies and self-interstitials. However, in the presence of sustained point defect fluxes, the coupled transport of atomic components with inherently different diffusivities often leads to radiation-induced segregation (RIS), with undesired effects on properties such as intergranular corrosion and stress-assisted cracking. In this talk, we investigate the fundamental mechanisms leading to GB segregation in BCC FeCr-based alloys using multiscale modeling and experiments. A phase-field model is employed to account for both thermodynamic and kinetic segregation mechanisms. The full Onsager transport matrix is derived using kinetic Monte Carlo, molecular dynamics, and kinetic cluster expansion (KineCluE) calculations. The thermodynamics of GB segregation is described via an atomic density-based modification to the CALPHAD free energy. The modeling predictions are then compared against segregation data from atom probe characterization for various temperatures, compositions, and neutron irradiation conditions. We will conclude by discussing the utility of the multiscale modeling approach to shed light on the fundamental mechanisms leading to solute-GB interaction.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Impact of acidic pH on plant cell wall polysaccharide structure and dynamics: insights into the mechanism of acid growth in plants from solid-state NMR

Acidification of plant primary cell walls causes cell wall expansion and plant growth. To understand how acidic pH affects the molecular structure and dynamics of wall polysaccharides, we have now characterized and compared Arabidopsis thaliana primary cell walls in neutral (pH 6.8) and acidic (pH 4.0) conditions using solid-state NMR spectroscopy. Quantitative 13C solid-state NMR spectra indicate that the pH 4.0 cell wall has neutral galacturonic acid residues in homogalacturonan (HG) and rhamnogalacturonan (RG). 13C INEPT spectra, which selectively detect highly dynamic polymers, indicate that some of the HG and RG chains in the interfibrillar region have become more dynamic in the acidic wall compared to the neutral cell wall, whereas other chains have become more rigid. Consistent with this increased dynamic heterogeneity, C–H dipolar couplings and 2D 13C–13C correlation spectra indicate that some of the HG backbones are partially aggregated in the acidic cell wall. Moreover, 2D correlation spectra measured with long mixing times indicate that the acidic cell wall has weaker cellulose–pectin interactions, and water-polysaccharide 1H spin diffusion data show that cellulose microfibrils are better hydrated at low pH. Taken together, these results indicate a cascade of chemical and conformational changes of wall polysaccharides due to cell wall acidification. These changes start with neutralization of the pectic polysaccharides, which disrupts calcium crosslinking of HG, causes partial aggregation of the interfibrillar HG, weakens cellulose–pectin interactions, and increases the hydration of both cellulose microfibrils and matrix polysaccharides. These molecular-level structural and dynamical changes are expected to facilitate polysaccharide slippage, which underlies cell wall loosening and expansion, and may occur both independent of and as a consequence of protein-mediated wall loosening.

biofuels (including algae and biomass), bio-inspir↗
DOE OSTI2025

Speciation mapping of the oxidation layer on aged uranium dioxide using scanning transmission x-ray spectromicroscopy

In this study, UO 2 was aged in humid air and prepared as a thin section using a focused ion beam (FIB) instrument. The specimen was measured using synchrotron radiation spectromicroscopy techniques at the Beamline 11.0.2 STXM end station of the Advanced Light Source (ALS). Non-negative matrix factorization (NMF) methods were used to identify and map three component x-ray absorption near-edge structure (XANES) spectra in the oxygen K-edge data, revealing a surface layer of U 4 O 9 with a thickness of 206 ± 21 nm, and the bulk of the sample remaining as UO 2 . Uranium N 4,5 -edge XANES spectromicroscopy supports these results. The diffusion-controlled parabolic rate constant for UO 2 oxidation to U 4 O 9 was calculated from the observed layer thickness and compared to literature values. Complementary transmission electron microscopy (TEM) was used to image the sample and identify the phases present in various regions, confirming the STXM results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Investigation of Coupled Processes in Fractures and the Bordering Matrix via a Micro‐Continuum Reactive Transport Model

Abstract In multi‐mineral fractured rocks, the altered porous layer on the fracture surface resulting from preferential dissolution of the fast‐reacting minerals can have profound impacts on subsequent chemical‐physical alteration of the fractures. This study adopts the micro‐continuum approach to provide further understanding of reactive transport processes in the altered layer (AL), and mass exchanges with the bordering matrix and fracture. The modeling framework couples the Darcy‐Brinkman‐Stokes (DBS) solver in COMSOL Multiphysics and the geochemical modeling capability of CrunchFlow. Three‐dimensional steady state simulations with systematically varied chemical‐physical parameters of the AL were performed to examine the impacts of individual factors and processes. Our simulation results confirm previous observations that dissolution of the fast‐reacting mineral (i.e., calcite) is largely controlled by diffusion across the AL. We also show that dissolution of the slow‐reacting mineral (i.e., dolomite), which controls AL development and fracture enlargement, increases with surface area and has a complex dependence on different local rate‐limiting processes. In particular, advection can result in evident spatial variations in the local dissolution rates of dolomite, although it does not affect the bulk chemistry significantly. The difference in the spatial patterns between simulations with and without advection in the AL is more noticeable in the locations with smaller apertures, with up to 20% difference in local reaction rates. Therefore, it is important to include a full depiction of advection, diffusion, and reactions for accurately capturing local dynamics that control long‐term fracture evolution.

58 GEOSCIENCES↗
DOE OSTI2025

Determining hexavalent chromium transport properties in alkaline nuclear waste using nuclear magnetic resonance spectroscopy

This study focuses on the transport properties of hexavalent chromium, specifically the chromate anion, to improve predictive models and environmental remediation strategies for Cr(VI) migration. Using 53 Cr Nuclear Magnetic Resonance (NMR) spectroscopy, the research quantifies chromate in multicomponent electrolytes replicating nuclear waste conditions at the Hanford Site in Washington State. The consistency of the 53 Cr NMR signal integral with chromate concentration, despite varying matrix compositions, establishes it as a reliable concentration indicator. The transport properties of chromate in an alkaline solution were assessed using relaxation-based measurements via saturation recovery and Carr-Purcell-Meiboom-Gill experiments, determining spin-lattice and spin-spin relaxation times. These measurements, combined with the Bloembergen-Purcell-Pound equation, helped estimate the rotational correlation time and the 53 Cr self-diffusion coefficient using Stokes-Einstein-Debye and Stokes-Einstein equations. Direct measurements were obtained through pulsed field gradient stimulated echo 53 Cr NMR spectroscopy. Monte Carlo simulations further estimated uncertainty propagation. The results enhance comprehension of chromate transport and highlight prospects for identifying transport properties of NMR-active nuclei, traditionally considered unreachable.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Influence of substrate composition on size and chemical state of ion beam synthesised Co nanoparticles – Towards fabrication of electrodes for energy devices

A one-step approach to synthesize ultrafine transition metal particles (size < 5 nm) in carbon substrates is highly desirable for fabricating electrodes for energy devices. Herein, cobalt ion implantation into amorphous carbon films (a:C) and hydrogenated amorphous carbon films (a:CH) was explored, with the aim of synthesizing ultrafine metallic cobalt nanoparticles at room temperature. Co ions of 30 keV energy were implanted into the carbon films to achieve a Co areal density of 1.0 ± 0.1 × 10 17 atoms cm -2 . Rutherford backscattering measurements revealed that hydrogenated amorphous carbon films gave a broader Co depth distribution compared to the amorphous carbon films. Further, cross-sectional TEM analysis revealed that hydrogenated carbon films suppressed metallic Co nanoparticle aggregation, leading to the creation of ultrafine Co nanoparticles (size < 5 nm). Co L-edge X-ray absorption spectroscopy measurements confirmed the formation of predominantly metallic Co nanoparticles by ion implantation. Results conclusively demonstrate that the presence of hydrogen (~ 28 at%) in the carbon matrix facilitates the synthesis of ultrafine metallic Co nanoparticles during Co ion implantation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Structural and Morphological Features of TiNi-Based Powder Manufactured by the Method of Hybrid-Calcium Reduction

An investigation of the structural features and surface morphology of a PV-N55T45 TiNi-based powder manufactured by the method of hybrid-calcium reduction is performed. The TiNi intermetallic compound is found in a two-phase state – B2 and В19′, and the following secondary phases are revealed: Ti{sub 2}Ni, Ti{sub 4}Ni{sub 2}(О, N, С), TiNi{sub 3}, and Ti{sub 3}Ni{sub 4}. It is observed that TiNi-based powder has dual – compact and spongy – morphology. The compact powder particles consist of oval coarse grains of TiNi separated by a massive Ti{sub 2}Ni interlayer. In the spongy particles, in contrast to the compact ones, the TiNi-phase prevails in the form of a single conglomerate of fine grains measuring 10–20 μm. In the Ni-enriched regions of the TiNi matrix the B19′-martensite is observed in multiple structural-morphological variants. In the compact particles the martensite structure represents orthogonal twin plates having different orientations within one grain. In the spongy particles, there is a different type of the martensite structure with multiple crystals of the B19′-martensite with the pyramidal lath morphology. On the surface of certain particles there is terraced relief formed due to bulk diffusion of atoms, surface diffusion of adatoms, and their interaction with the substrate defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

A Galerkin method with two-dimensional Haar basis functions for the computation of the Karhunen–Loève expansion

We study the numerical approximation of a homogeneous Fredholm integral equation of second kind associated with the Karhunen–Loève expansion of Gaussian random fields. We develop, validate, and discuss an algorithm based on the Galerkin method with two-dimensional Haar wavelets as basis functions. The shape functions are constructed from the orthogonal decomposition of tensor-product spaces of one-dimensional Haar functions, and a recursive algorithm is employed to compute the matrix of the discrete eigenvalue system without the explicit calculation of integrals, allowing the implementation of a fast and efficient algorithm that provides considerable reduction in CPU time, when compared with classical Galerkin methods. Numerical experiments confirm the convergence rate of the method and assess the approximation error and the sparsity of the eigenvalue system when the wavelet expansion is truncated. We illustrate the numerical solution of a diffusion problem with random input data with the present method. In this problem, accuracy was retained after dropping the coefficients below a threshold value that was numerically determined. A similar method with scaling functions rather than wavelet functions does not need a discrete wavelet transform and leads to eigenvalue systems with better conditioning but lower sparsity.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2014

Controlling diffusion for a self-healing radiation tolerant nanostructured ferritic alloy

Diffusion plays a major role in the stability of microstructures to extreme conditions of high temperature and high doses of irradiation. In nanostructured ferritic alloys, first principle calculations indicate that the binding energy of vacancies is reduced by the presence of oxygen, titanium and yttrium atoms. Therefore, the number of free vacancies available for diffusion can be greatly reduced. The mechanical properties of these alloys, compared to traditional wrought alloys of similar composition and grain structure, is distinctly different, and the ultrafine grained alloy is distinguished by a high number density of Ti–Y–O-enriched nanoclusters and solute clusters, which drives the mechanical response. When a displacement cascade interacts with a nanocluster, the solute atoms are locally dispersed into the matrix by ballistic collisions, but immediately a new nanocluster reforms due to the local supersaturation of solutes and vacancies until the excess vacancies are consumed. Furthermore, the result of these processes is a structural material for advanced energy systems with a microstructure that is self-healing and tolerant to high doses of radiation and high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Graphene foam integrated with lithium titanate as anode of Li ion batteries

Graphical abstract: Integrated graphene foam supported LTO electrodes are synthesized via a hydrothermal method and exhibit a noticeable electrochemical performance as cathode of Li ion batteries. - Highlights: • Integrated graphene foam supported LTO electrodes are synthesized. • Self-supported GF/LTO electrodes show high electrochemical performance. • Integrated porous architecture is favorable for capacity enhancement. - Abstract: In this work, we construct a binder-free electrode by integrating Li{sub 4}Ti{sub 5}O{sub 12} (LTO) nanoparticles onto free-standing graphene foam (GF) via hydrothermal method. The CVD-grown GF is used as the backbone for the deposition of LTO nanoparticles of 20–50 nm. Enhanced reaction kinetics including fast ion/electron transfer is achieved with the help of conductive GF matrix. The electrochemical performance of the VG/LTO as the anode of Li ion batteries (LIBs) are studied and demonstrated with a capacity of 171 mAh g{sup −1} at 1 C, and good cycles with a capacity retention of 77%. High-rate capability is also verified with a capacity of 108 mAh g{sup −1} at 10 C. The designed porous integrated architecture is favorable for the diffusion of ion/electrons, and good contact with the electrolyte. Our results provide a new way for developing high-performance anode of LIBs.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Effect of the size of nanoparticles on their dissolution within metal-glass nanocomposites under sustained irradiation

We investigate the dissolution law of metallic nanoparticles (NPs) under sustained irradiation. The system is composed of isolated spherical gold NPs (4–100 nm) embedded in an amorphous silica host matrix. Samples are irradiated at room temperature in the nuclear stopping power regime with 4 MeV Au ions for fluences up to 8 × 10{sup 16 }cm{sup −2}. Experimentally, the dependence of the dissolution kinetics on the irradiation fluence is linear for large NPs (45–100 nm) and exponential for small NPs (4–25 nm). A lattice-based kinetic Monte Carlo (KMC) code, which includes atomic diffusion and ballistic displacement events, is used to simulate the dynamical competition between irradiation effects and thermal healing. The KMC simulations allow for a qualitative description of the NP dissolution in two main stages, in good agreement with the experiment. Moreover, the perfect correlation obtained between the evolution of the simulated flux of ejected atoms and the dissolution rate in two stages implies that there exists an effect of the size of NPs on their dissolution and a critical size for the transition between the two stages. The Frost-Russell model providing an analytical solution for the dissolution rate, accounts well for the first dissolution stage but fails in reproducing the data for the second stage. An improved model obtained by including a size-dependent recoil generation rate permits fully describing the dissolution for any NP size. This proves, in particular, that the size effect on the generation rate is the principal reason for the existence of two regimes. Finally, our results also demonstrate that it is justified to use a unidirectional approximation to describe the dissolution of the NP under irradiation, because the solute concentration is particularly low in metal-glass nanocomposites.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Phase-field simulations of fission gas bubble growth and interconnection in U-(Pu)-Zr nuclear fuel

Abstract The growth and interconnection of fission gas bubbles in the hotter central regions of U-(Pu)-Zr nuclear fuel has been simulated with a phase-field model. The Cahn-Hilliard equation was used to represent the two-phase microstructure, with a single defect species. The volume fraction of the bubble phase and surface area of the bubble-matrix interface were determined during growth and interconnection. Surface area increased rapidly during the initial stages of growth, then slowed and finally decreased as bubble interconnection began and coarsening acted to reduce surface area. The fraction of the bubbles vented to a simulation domain boundary, f V , was quantified as a measure of the microstructure’s interconnectivity and plotted as a function of porosity p . The defect species diffusivity was varied; although changes in diffusivity significantly affected the microstructure, the plots of f V vs. p did not change significantly. The percolation threshold p c was calculated to be approximately 0.26, depending on the assumed diffusivity and using an initial bubble number density based on experimental observations. This is slightly smaller than the percolation threshold for continuum percolation of overlapping 3D spheres. The simulation results were used to parameterize two different engineering-scale swelling models for U-(Pu)-Zr in the nuclear fuel performance code BISON.

Aagesen, Larry K. (ORCID:000000034936676X)↗