Search NASA⌕ Search

SEARCH · Search NASA

Results for “polyurethanes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 649 records · Page 36

Modeling the measured effect of a nitroplasticizer (BDNPA/F) on cookoff of a plastic bonded explosive (PBX 9501)

Here, we have used a modified version of the Sandia Instrumented Thermal Ignition (SITI) experiment to develop a pressure-dependent, five-step ignition model for a plastic bonded explosive (PBX 9501) consisting of 95 wt% octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazoncine (HMX), 2.5 wt% Estane® 5703 (a polyurethane thermoplastic), and 2.5 wt% of a nitroplasticizer (NP): BDNPA/F, a 50/50 wt% eutectic mixture bis(2,2-dinitropropyl)-acetal (BDNPA) and bis(2,2-dinitropropyl)-formal (BDNPF). The five steps include desorption of water, decomposition of the NP to form NO2, reaction of the NO2 with Estane® and HMX, and decomposition of HMX. The model was fit using our experiments and successfully validated with experiments from five other laboratories with scales ranging from about 2 g to more than 2.5 kg of PBX. Our experimental variables included density, confinement, free gas volume, and temperature. We measured internal temperatures, confinement pressure, and ignition time. In some of our experiments, we used a borescope to visually observe the decomposing PBX. Our observations included the endothermic β–δ phase change of the HMX, a small exothermic temperature excursion in low-density unconfined experiments, and runaway ignition. We hypothesize that the temperature excursion in these low density experiments was associated with the NP decomposing exothermically within the PBX sample. This reactant-limited temperature excursion was not observed with our thermocouples in the high-density experiments. For these experiments, we believe the binder diffused to the edges of our high density samples and decomposed next to the highly conductive wall as confirmed by our borescope images.

42 ENGINEERING↗

Performance assessment of 3D printed multi-material energy absorber for automotive bumper: pedestrian lower extremity protection

Designing an energy absorber for automotive bumpers involves balancing low-speed and high-speed impacts to ensure safety, reduce repair costs, and meet regulatory standards. Here, this study explores a novel design using multi-material 3D printing and structural optimization to fabricate a lightweight and cost-efficient energy absorber. The design effectively dissipates energy in low-speed collisions and minimizes force transmission in high-speed pedestrain impacts, helping to meet both safety and performance requirements. The energy absorber design combines 20% carbon fiber-reinforced acrylonitrile butadiene styrene (CF-ABS) and thermoplastic polyurethane (TPU) for optimal stiffness and flexibility. It uses 3D-printed lattice structures optimized through finite element simulations to help meet both low-speed and high-speed impact requirements. Full-scale energy absorbers were 3D-printed using optimized CF-ABS/TPU blends and tested under high-speed impact using the Flexible Pedestrian Legform Impactor (Flex-PLI). For fair comparison, a baseline bumper with a traditional triangular lattice structure, also 3D-printed from the same CF-ABS/TPU materials, was similarly tested. Interestingly, both the optimized and baseline 3D-printed energy absorbers showed nearly identical performance, successfully meeting injury limits. Their performances were also benchmarked against an injection-molded energy absorber. While both 3D-printed and injection-molded designs met injury limits, the 3D-printed absorber exhibited a higher tibia bending moment, indicating an opportunity for further optimization. A Techno-Economic Analysis compared the costs of producing energy absorbers using traditional manufacturing and 3D printing. The analysis highlighted that 3D printing offers cost benefits for low to medium production volumes, with the total cost per energy absorber at ∼ $\$$74, compared to traditional methods that become economical beyond 2000 units.

Additive manufacturing↗

Pressure drop of two-phase dry-plug flow in round mini-channels: Effect of moving contact line

In the present experimental study, the pressure drop of the two-phase dry-plug flow (dry wall condition at the gas portions) in round mini-channels was investigated. The air-water mixtures were flowed through the round mini-channels made of polyurethane and Teflon, respectively, with their inner diameters ranging from 1.62 to 2.16 mm. In the dry-plug flow regime, the pressure drop measured became larger either by increasing the liquid superficial velocity or by decreasing the gas superficial velocity due to the increase of the number of the moving contact lines in the test section. In such a case, the role of the moving contact lines turned out to be significant. Therefore, a pressure drop model of dry-plug flow was proposed through modification of the dynamic contact angle analysis taking account of the energy dissipation by the moving contact lines, which represents the experimental data within the mean deviation of 4%. (author)

42 ENGINEERING↗

Investigation of the dynamic stress–strain response of compressible polymeric foam using a non-parametric analysis

Dynamic stress–strain response of rigid closed-cell polymeric foams is investigated in this work by subjecting high toughness polyurethane foam specimens to direct impact with different projectile velocities and quantifying their deformation response with high speed stereo-photography together with 3D digital image correlation. The measured transient displacement field developed in the specimens during high stain rate loading is used to calculate the transient axial acceleration field throughout the specimen. A simple mathematical formulation based on conservation of mass is also proposed to determine the local change of density in the specimen during deformation. By obtaining the full-field acceleration and density distributions, the inertia stresses at each point in the specimen are determined through a non-parametric analysis and superimposed on the stress magnitudes measured at specimen ends to obtain the full-field stress distribution. Furthermore, the process outlined above overcomes a major challenge in high strain rate experiments with low impedance polymeric foam specimens, i.e. the delayed equilibrium conditions can be quantified.

42 ENGINEERING↗

On the Need for Comprehensive Validation of Deformable Image Registration, Investigated With a Novel 3-Dimensional Deformable Dosimeter

Purpose: To introduce and evaluate a novel deformable 3-dimensional (3D) dosimetry system (Presage-Def/Optical-CT) and its application toward investigating the accuracy of dose deformation in a commercial deformable image registration (DIR) package. Methods and Materials: Presage-Def is a new dosimetry material consisting of an elastic polyurethane matrix doped with radiochromic leuco dye. Radiologic and mechanical properties were characterized using standard techniques. Dose-tracking feasibility was evaluated by comparing dose distributions between dosimeters irradiated with and without 27% lateral compression. A checkerboard plan of 5-mm square fields enabled precise measurement of true deformation using 3D dosimetry. Predicted deformation was determined from a commercial DIR algorithm. Results: Presage-Def exhibited a linear dose response with sensitivity of 0.0032 ΔOD/(Gy∙cm). Mass density is 1.02 g/cm{sup 3}, and effective atomic number is within 1.5% of water over a broad (0.03-10 MeV) energy range, indicating good water-equivalence. Elastic characteristics were close to that of liver tissue, with Young's modulus of 13.5-887 kPa over a stress range of 0.233-303 kPa, and Poisson's ratio of 0.475 (SE, 0.036). The Presage-Def/Optical-CT system successfully imaged the nondeformed and deformed dose distributions, with isotropic resolution of 1 mm. Comparison with the predicted deformed 3D dose distribution identified inaccuracies in the commercial DIR algorithm. Although external contours were accurately deformed (submillimeter accuracy), volumetric dose deformation was poor. Checkerboard field positioning and dimension errors of up to 9 and 14 mm, respectively, were identified, and the 3D DIR-deformed dose γ passing rate was only γ{sub 3%/3} {sub mm} = 60.0%. Conclusions: The Presage-Def/Optical-CT system shows strong potential for comprehensive investigation of DIR algorithm accuracy. Substantial errors in a commercial DIR were found in the conditions evaluated. This work highlights the critical importance of careful validation of DIR algorithms before clinical implementation.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Towards functionalized lignin and its derivatives for high-value material applications

In pursuit of low-carbon development, the production of diverse functional materials from renewable resources, especially lignocellulosic biomass, is of vital importance. Lignin is a major component of lignocellulose, and it is nature's only true high-volume aromatic polymer, which has the advantages of biodegradability, biocompatibility, and low acquisition cost. After modification by a variety of physicochemical strategies, it can be applied as an alternative to basic industrial materials, including polyurethanes, phenolic, and epoxy resins, which stands comparably to conventional synthetic polymers in terms of both performance and reduced cost. To further unlock the potential of lignin, an alluring opportunity is the exploitation of lignin for high-value materials, especially nanomaterials, that find extensive applications in energy and environment areas. This review provides a systematic summary and perspective of research that has been devoted to lignin transformation to high-value materials, ranging from industrially well-established engineering materials to the recently emerged nanomaterials that were used for energy and environment applications. Latest cutting-edge innovations on lignin modification, controlled depolymerization, and assembly during the last five years are summarized. Structure-function relationships of lignin materials in terms of their specific applications are analyzed. Furthermore, challenges and future opportunities for lignin conversion to high-value materials are also provided. We wish this review will stimulate further advances in lignin based high-value materials, and promote “waste” into “wealth”.

36 MATERIALS SCIENCE↗

Minimized aging of isocyanurate-based rigid cellular foams for buildings through tailored barrier facers and optimized formulation

The thermal resistivity (h·ft 2 ·°F/Btu/in.) of closed-cell rigid foam insulation materials significantly decreases over time. Diffusion-tight facers are designed to significantly enhance initial thermal resistivity and long-term thermal performance by preventing gas diffusion into the foam cells and inhibiting the escape of low thermal conductivity blowing agents. In addition to the gas diffusion property of the facer film, adhesion between the foam and the facer is crucial for achieving diffusion-tight bonding. Here, this study addresses the challenge of thermal aging by investigating how facer film properties and foam formulation influence the durability of thermal performance. A systematic evaluation was conducted to understand the effects of polymeric barrier films, surface treatments, facer coverage, and foam matrix rigidity on thermal resistivity over time. Key findings reveal that diffusion-tight facers, particularly those with metallized layers and compatible heat seal layers, significantly reduce gas exchange and improve foam-facer adhesion. The optimized system, incorporating barrier facers and a tailored polyisocyanurate foam formulation, achieved initial and aged thermal resistivity values after 200 days of approximately 8.3 and 7.4 h ft 2 ·°F/Btu/in., respectively representing only a 10 % reduction compared to a 17 % reduction observed in control samples without facers. Notably, polyurethane spray foams with facers exhibited only a 4 % reduction in thermal resistivity, compared to a 23 % decrease in control samples, demonstrating nearly six times better retention of thermal performance. This innovative facer technology presents a promising solution for reducing energy costs and represents a significant advancement in optimizing energy management for building envelopes in future technologies. This technology can also be adapted for other applications that necessitate the preservation of long-term thermal performance.

Wanasinghe, Shiwanka Vidarshi [Oak Ridge National ↗

Property optimized energy absorber for automotive bumpers utilizing multi-material and structural design strategies

This study proposes a novel design for automotive bumper using optimized lattice structures and multi-materials to balance low-speed collision and high-speed pedestrian impact performance. Different blends of 20 % carbon fiber-reinforced acrylonitrile butadiene styrene with thermoplastic polyurethane were used to tailor material properties. The energy absorber features lattice structures with customized mechanical responses, created by varying the incline angle θ from 0 to 180°. We conducted 576 finite element simulations on a half-scale model to optimize energy absorption and stiffness, leading to 66 optimized designs that met both low-speed and high-speed impact criteria. Two sub-scale optimized energy absorbers with different peak forces—both meeting low-speed impact requirements—were 3D printed and validated through drop-weight testing. The one with lower peak stress demonstrated a more compliant response, exhibiting approximately 90 % lower initial peak force and an increase in energy absorption of around 33 % (from 24 J to 32 J). Compared to the baseline triangular lattice, the optimized absorber increased energy absorption by 68 % from (19 J to 32 J) and reduced peak stress by 70 %. It also showed near-complete recovery with minimal fractures, making it suitable for repeated use. This design improves safety while offering a lightweight, durable, and cost-effective bumper system.

36 MATERIALS SCIENCE↗

Characterization of CO 2 flux through hollow-fiber membranes using pH modeling

CO 2 must be delivered efficiently during large-scale microalgal cultivation. Bubbleless mass-transfer via diffusion through hollow-fiber membranes (HFM) can achieve much higher CO 2 -transfer efficiency than traditional sparging systems. Here this study developed and used a model to compute accurate values for the CO 2 flux (J CO 2 ), overall mass-transfer coefficient (K L ), and overall volumetric mass-transfer coefficient (K L a) based on the rate of change of pH in batch experiments. A composite HFM comprised of two macroporous polyethylene layers and a nonporous polyurethane layer was tested for CO 2 transfer to a sodium carbonate solution using a range of total pressures, inlet CO 2 concentrations, and open-end versus closed-end modes of operation. The model accurately computed J CO2 and K L a for pH values above 8. Key trends are that (i) JCO2 and KLa increased with increasing average inlet CO 2 partial pressure; (ii) open-end HFMs performed better than closed-end HFMs when the supplied CO 2 was less than 100%; and (iii) the available membrane area used for CO 2 mass-transfer decreased as the inlet CO 2 partial pressure decreased due to depletion of CO 2 inside the membrane, especially for closed-end HFMs, since inert gases could not be vented.

42 ENGINEERING↗

Anisotropy evolution of elastomeric foams during uniaxial compression measured via in-situ X-ray computed tomography

We have characterized the three-dimensional evolution of microstructural anisotropy of a family of elastomeric foams during uniaxial compression via in-situ X-ray computed tomography. Flexible polyurethane foam specimens with densities of 136, 160 and 240 kg/m 3 were compressed in uniaxial stress tests both parallel and perpendicular to the foam rise direction, to engineering strains exceeding 70%. The uncompressed microstructures show slightly elongated ellipsoidal pores, with elongation aligned parallel to the foam rise direction. The evolution of this microstructural anisotropy during deformation is quantified based on the autocorrelation of the image intensity, and verified via the mean intercept length as well as the shape of individual pores. Trends are consistent across all three methods. In the rise direction, the material remains transversely anisotropic throughout compression. Anisotropy initially decreases with compression, reaches a minimum, then increases up to large strains, followed by a small decrease in anisotropy at the largest strains as pores collapse. Compression perpendicular to the foam rise direction induces secondary anisotropy with respect to the compression axis, in addition to primary anisotropy associated with the foam rise direction. In contrast to compression in the rise direction, primary anisotropy initially increases with compression, and shows a slight decrease at large strains. These surprising non-monotonic trends and qualitative differences in rise and transverse loading are explained based on the compression of initially ellipsoidal pores. Microstructural anisotropy trends reflect macroscopic stress-strain and lateral strain response. These findings provide novel quantitative connections between three-dimensional microstructure and anisotropy in moderate density polymer foams up to large deformation, with important implications for understanding complex three-dimensional states of deformation.

36 MATERIALS SCIENCE↗

Versatile coating with multifunctional performance for solar steam generation

In this work, a new kind of material, composite complex coating (CCC), with multifunctional performance has been developed for solar steam generation. The CCC has many advantages: (a) Scalability. The fabrication process is facile and mild; it can be realized in aqueous solution at room temperature, without high pressure, toxic organic solvents, or complex equipment. (b) Cost-effectiveness. The reagents used for preparation of CCC are low-cost and readily available. (c) Universality and stability. CCC firmly adheres on surfaces of various substrates with diverse shapes (cotton, filter paper, wood, polyurethane sponge, and even chemically inert and highly hydrophobic polyvinylidene fluoride membranes), and can withstand rinsing treatment (3000 r/min for 96 h), cyclic frost-thaw test (-18 °C ⇌ 30 °C, 90 times), and both high and low pH environments. In addition, many other reported coatings, such as carbon black, fail under similar process strain. (d) Anti-crude oil-fouling property. The CCC possesses stable superhydrophilicity and underwater superoleophobicity, which collectively endow substrates with the ability to resist fouling by oils. (e) Broad and strong light absorption. CCC can transform various substrates with diverse shapes into black materials with broadband light absorption due to its d-d transitions and rough surface. Together, these properties of CCC enable substrates with nearly any structural design to be easily transformed into photothermal materials for efficient solar steam generation. Furthermore, as a proof of concept, poplar wood is treated with CCC, achieving a water evaporation rate of ~1.8 kg m-2 h-1 (one sun), which is a record among wood-based photothermal materials.

14 SOLAR ENERGY↗

Diffusion-limited hydrolysis in polymeric materials

Polymer degradation under aggressive environmental stressors often develops heterogeneities due to diffusion-limited reaction phenomena. This is well established for diffusion-limited oxidation (DLO), which is known to occur for most polymeric materials at elevated temperatures but has been less summarized for the conditions of diffusion-limited hydrolysis (DLH). Here, an overview of hydrolysis for several materials and a computational model, analogous to the underlying equations for DLO, able to define this diffusion-reaction system is presented. A systematic study of the influence of various parameters, such as water diffusivity, reaction rate and order, and a more in-depth focus on residual isocyanate hydrolysis in a polymeric methylene diphenyl diisocyanate (pMDI) based polyurethane (PU) foam is given. For this system, we present experimental data for model ‘input’ parameters and discuss predictions for different conditions. We conceptually compare the behavior of diffusion-limited oxidation to that of diffusion-limited hydrolysis (DLH). With the mathematical framework and key material properties presented herein, any DLH phenomena following Fickian diffusion behavior can be understood, modeled, and predicted.

36 MATERIALS SCIENCE↗

Cohesive and adhesive degradation in PET-based photovoltaic backsheets subjected to ultraviolet accelerated weathering

Delamination between layers in photovoltaic (PV) backsheets is often reported in the literature, causing voids that can collect moisture, diminish module backside heat dissipation, and reduce the backsheet’s effectiveness as a physical barrier. While backsheets with weathering-resistant fluoropolymer outer layers have traditionally been used in modules, more recent backsheets using non-fluoropolymer outer layers, such as polyethylene terephthalate (PET), have been developed. These backsheets have shown signs of premature degradation, and their adhesion degradation, in particular, has not been widely studied. In the present work, the single cantilever beam (SCB) adhesion test was used to quantify the adhesion energy in two commercially available PET-based backsheets. To study the effect of minor changes in formulation, the backsheets were obtained from same manufacturer and product line but during different years. To study the effect of environmental variables on adhesion degradation, the backsheets were subjected to artificial weathering at controlled temperature, humidity, and ultraviolet (UV) radiation in an indoor weathering chamber, and the adhesion energy was quantified at several intervals of exposure time. Layering structure, composition, and adhesion failure mode were compared between the backsheets, using Raman and infrared spectroscopy and thermogravimetric analysis. The results show a large difference in initial (unexposed) adhesion energy between the backsheets, despite very similar structures and compositions. Following exposure, adhesion energy dropped significantly, primarily due to thermo-hydrolytic degradation of the polyurethane (PU)-based adhesive layers. Significant UV-induced adhesion degradation of the PET outer layer surface was also observed. The study represents an important step in understanding adhesion degradation in PET-based backsheets, suggesting ways in which adhesion integrity – and, correspondingly, module service life – can be improved.

14 SOLAR ENERGY↗

CRISPR/Cas9 editing of p-COUMAROYL-CoA:MONOLIGNOL TRANSFERASE 1 in maize alters phenolic metabolism, lignin structure, and lignin-first biomass processing

Valorization of lignocellulosic biomass for sustainable production of high-value chemicals is challenged by the complexity of lignin, a phenolic biopolymer. Beyond the classical lignin monomers derived from p-coumaryl, coniferyl, and sinapyl alcohol, grass lignins incorporate substantial amounts of monolignol p-coumarates that are produced by p-COUMAROYL-CoA:MONOLIGNOL TRANSFERASE (PMT). Here, the CRISPR/Cas9-mediated mutation of ZmPMT1 in maize enabled the design of biomass depleted in p-coumaroylated lignin and enriched in guaiacyl lignin. Lignin-first biorefining of stem biomass from zmpmt1 mutants by reductive catalytic fractionation (RCF) generated a lignin oil depleted in carboxylates and enriched in guaiacyl-derived alcohols, which are desirable substrates for bio-based polyurethane synthesis. Furthermore, the reported lignin engineering in maize is a promising strategy for designing a dual-purpose crop, providing both food and feed, along with a renewable feedstock for the production of plant-based chemicals.

59 BASIC BIOLOGICAL SCIENCES↗

Exploring strain rate effects upon 3D materials using high speed in situ X-ray tomoscopy

Cellular materials are ubiquitous in our modern society. They may be stochastic gas-blown foams (e.g., polyurethane), foamed starches (e.g., cereals), or, in this case, 3D printed microlattices. Failure in these materials is often driven by surface or sub-surface defects, which may be nucleated at a surface roughness, an interior void, or inclusion interfaces that may not be typically observable. Obfuscating our understanding further, bulk materials are known to exhibit strain-rate-dependent mechanical response, making a subsurface understanding of damage even more critical. For the first time, an in situ uniaxial mechanical loading stage that simultaneously rotates specimens up to 18 Hz was fielded at a synchrotron for 3D tomographic imaging. This capability opens a plethora of materials science opportunities to explore strain rate effects in materials and examining deformation, fracture, and delamination’s (in composites) for a complete 3D picture (movie) of material response. We demonstrate the deformation of 3D printed polymer lattice structures, of three different material types, at 0.25, 1.1, and 2.2 s −1 strain rates. We successfully imaged the 3D deformation of these materials and can directly compare the same printed structure to the three material types at three strain rates, all in 3D. Material point method simulations were applied to one of the materials to better understand the role of voids on the 3D printed structure’s performance.

36 MATERIALS SCIENCE↗

Efficient microwave absorption with V n+1 C n T x MXenes

The availability of MXenes and other two-dimensional conductive nanomaterials with tunable surface chemistry has reshaped the field of electromagnetic protection. However, the high electrical conductivity and low dielectric loss of titanium-based MXenes lead to strong reflection of electromagnetic waves, even when combined with polymers to form composites. Here, we report on the ability of vanadium-based MXenes to provide broadband microwave absorption. Polyurethane composites with ~2 wt % V n+1 C n T x can absorb 90% of electromagnetic waves covering the entire X band. In addition, pure V n+1 C n T x films of submicrometer thickness can provide effective electromagnetic interference shielding. The free electron transport, surface terminations, native defects, and layers arrangement in composites have profound effects on electronic and dielectric properties of V n+1 C n T x MXenes. This study points toward a new frontier for development of thin and highly absorbing MXene-based electromagnetic protection materials.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Identification of Known and Novel Monomers for Poly(hydroxyurethanes) from Biobased Materials

Sourcing polymers from biobased materials is desirable for a transition to a more sustainable world. However, finding new monomers sourced from biobased molecules requires extensive experimental effort, due to the fact that most biomolecules lack the functional groups or properties needed to serve as a monomer in a particular polymeric system without chemical modification. In this work, we demonstrate a computational screening method to obtain monomers of a non-isocyanate polyurethane (NIPU), polyhydroxyurethane (PHU), from biomolecules. Our method generates candidate monomers from a list of 15 selected biobased starting molecules by performing chemical transformations that are standard to chemical catalysis and organic synthesis on these starting molecules and then screening the results for molecules with moieties that can be used as monomers for a PHU. Product molecules from two generations of reaction, a total number of 20,057, were analyzed automatically to identify molecules that have two or more epoxy or cyclic carbonate functional groups as candidates for further derivatization. These 21 candidate molecules were then subjected to another two generations of reaction, producing a set of 17,913 additional molecules. Further scrutiny of this set for desired functional groups characterizing PHUs and querying against the PubChem database was carried out, and 15 known molecules that are commercially available were identified, with the desirable features that they are predicted to be derived from biobased starting molecules in four or fewer steps. Moreover, molecule space generated from this process was primarily comprised of molecules that were not known to PubChem, indicating the framework also has the ability to generate novel candidate monomers that originate from biobased starting points.

36 MATERIALS SCIENCE↗

Scale-Up of a Two-Stage Cu-Catalyzed Alkaline-Oxidative Pretreatment of Hybrid Poplar

A two-stage alkaline-oxidative pretreatment of hybrid poplar was investigated at scale (20 L reactor volume) with the goals of understanding how reaction conditions as well as interstage mechanical refining impact downstream process responses. The pretreatment comprises a first stage of alkaline delignification (alkaline pre-extraction) followed by a second delignification stage employing Cu-catalyzed alkaline hydrogen peroxide with supplemental O 2 (O 2 -enhanced Cu-AHP). Increasing pre-extraction severity (i.e., temperature and alkali loading) and pre-treatment oxidation (increasing H 2 O 2 loading) were found to increase mass and lignin solubilization in each stage. Lignin recovered from the first stage was subjected to oxidative depolymerization and led to aromatic monomer yields as high as 23.0% by mass. As a result, lignins recovered from the second stage Cu-AHP pretreatment liquors were shown to exhibit aliphatic hydroxyl contents more than six-fold higher than for a typical hardwood kraft lignin, indicating these lignins could serve as a biobased polyol for a range of polyurethane applications.

09 BIOMASS FUELS↗