Search NASA⌕ Search

SEARCH · Search NASA

Results for “ABRASIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Anti-reflection coatings applied by acid leaching process

The Magicote C process developed by S.M. Thompsen was evaluated for use in applying an antireflective coating to the cover plates of solar panels. The process uses a fluosilicic acid solution supersaturated with silica at elevated temperature to selectively attack the surface of soda-lime glass cover plates and alter the physical and chemical composition of a thin layer of glass. The altered glass layer constitutes an antireflective coating. The process produces coatings of excellent optical quality which possess outstanding resistance to soiling and staining. The coatings produced are not resistant to mechanical abrasion and are attacked to some extent by glass cleansers. Control of the filming process was found to be difficult.

Pastirik, E.↗
NASA NTRS1980

Spatial distribution of volatile compounds in graphite composites

The distribution of water and other volatile compounds such as acetone and phenol was measured as a function of depth in four graphite resin matrix composites. Precision abrasion mass spectrometry was used to qualitatively and quantitatively characterize the indigenous volatile compounds in the as received condition and after drying in an environmentally controlled oven. The total amount of water in the composites varied from 0.12 wt% to 1.1 wt% and the times required to dry the samples ranged from less than 96 h to much greater than 555 h.

Grayson, M. A.↗
NASA NTRS1981

Advanced turbine blade tip seal system

An advanced blade/shroud system designed to maintain close clearance between blade tips and turbine shrouds and at the same time, be resistant to environmental effects including high temperature oxidation, hot corrosion, and thermal cycling is described. Increased efficiency and increased blade life are attained by using the advanced blade tip seal system. Features of the system include improved clearance control when blade tips preferentially wear the shrouds and a superior single crystal superalloy tip. The tip design, joint location, characterization of the single crystal tip alloy, the abrasive tip treatment, and the component and engine test are among the factors addressed. Results of wear testing, quality control plans, and the total manufacturing cycle required to fully process the blades are also discussed.

Zelahy, J. W.↗
NASA NTRS1981

Development of silane-hydrolysate binder for UV-resistant thermal control coatings

Detailed characterizaton and formulation studies were performed on a methyltriakoxysilane hydrolysate as a binder for thermal control coatings. The binder was optimized by varying hydrolysis temperature, time, catalyst type, and water concentration. The candidate coating formulations, based on this binder with TiO2 pigment, were optimized via a detailed series of sprayed test panels that included the parameters of binder/pigment ratio, ethanol content, pigment particle size, coating thickness and cure conditions. A typical optimized coating was prepared by acetic acid catalyzed hydrolysis of methyltriethoxysilane with 3.25 mol-equivalents of water over a 24 hour period at room temperature. The resulting hydrolysate was directly mixed with pre-milled TiO2 (12 grams pigment/26 grams binder) to yield a sprayable consistency. Panels were sprayed to result in a nominal cure coating thickness of 2 mils. Cure was affected by air drying for 24 hr at room temperature plus 72 hr at 150 F. These coatings are typically extremely tough and abrasion-resistant, with an absorptance (alpha) of 0.20 and emittance (e) of 0.89. No significant coating damage was observed in the mandrel bend test, even after exposure to thermal cycling from -160 to 160 F. Vacuum exposure of the coatings for 930 hours at 1 equivalent UV sun resulted in no visible degradation and no significant increase in absorptance.

Patterson, W. J.↗
NASA NTRS1980

Tribological properties of silicon carbide in metal removal process

This paper reviews material properties of adhesion, friction and wear of single-crystal silicon carbide in contact with metals and alloys involved in a metal removal process such as grinding. The tribological properties in the metal removal processes are divided into properties which remove metal by adhesion between sliding surfaces, and metal removal by silicon carbide sliding against a metal, indenting it, and plowing a series of grooves or furrows. The paper also deals with fracture and deformation characteristics of the silicon carbide surface; the adhesion, friction and metal transfer to silicon carbide is related to the relative chemical activity of the metals. Atomic size and content of alloying elements play a dominant role in controlling adhesion and friction properties of alloys. The friction and abrasive wear decrease as the shear strength of the bulk metal increases.

Miyoshi, K.↗
NASA NTRS1980

Low-cost conversion of polycrystalline silicon into sheet by HEM and FAST

The conversion of polycrystalline silicon to sheet form (the wafers produced are 10 cm x 10 cm cross section with minimum surface damage) by the Heat Exchanger Method (HEM) and multi-wire Fixed Abrasive Slicing Technique (FAST), as a means of reducing the cost of solar arrays for adaptation of photovoltaic technology for terrestrial applications, is given. A schematic of a HEM furnace, which includes a silica crucible, and developments in the HEM process are presented. A new machine for slicing with wire was designed and fabricated. The high-speed slicer has been used to slice 19 wafers per cm from 10 cm diameter crystals. Both HEM and FAST are low-cost processes and they have the potential of giving one of the lowest add-on costs ($6.24 and $6.48 per square meter of sheet respectively, with the combination add-on cost of $14.87 per square meter) of this conversion.

Khattak, C. P.↗
NASA NTRS1981

Dynamics of solid dispersions in oil during the lubrication of point contacts. I - Graphite

A Hertzian contact is lubricated with dispersed graphite in mineral oils under boundary lubrication conditions. The contacts are optically observed under pure rolling, combined rolling and sliding, and pure sliding conditions. The contact is formed with a steel ball on the flat surface of a glass disk. Under pure rolling and combined rolling and sliding conditions, it is found that, for low speeds, a graphite film can form which will separate the contacting surfaces. In contrast, under pure sliding conditions, graphite accumulates at the inlet and sweeps around the contact, but very little of graphite passes through the contact. The accumulated graphite appears to act as a barrier which reduces the supply of oil available to the contact for boundary lubrication. Friction data show no clear short-term beneficial or detrimental effect caused by addition of graphite to the base oil. However, during pure sliding, more abrasion occurs on the polished balls lubricated with the dispersion than on those lubricated with the base oil alone.

Cusano, C.↗
NASA NTRS1983

Improved Fluidized-Bed Gas Injector

Gas-injection cone in fluidized-bed reactor for coating particles with silicon or carbon cooled and protected from abrasion by stream of gas flowing over surface of cone. Hot particles entering reaction zone are coated with silicon or carbon supplied by thermal decomposition of suitable gas injected into reaction zone.

Hogle, R. A.↗
NASA NTRS1983

Development of Silane Hydrolysate Binder for Thermal-Control Coatings

Technical report describes theoretical and experimental development of methyltriethoxysilane (MTES) hydrolysate binder for white, titanium dioxidepigmented thermal-control coatings often needed on satellites. New coating is tougher and more abrasion-resistant than conventional coating, S-13G, which comprises zinc oxide in hydroxyl-therminated dimethylsiloxane binder.

Patterson, W. J.↗
NASA NTRS1981

Icing tunnel tests of a composite porous leading edge for use with a liquid anti-ice system

The efficacy of liquid ice protection systems which distribute a glycol-water solution onto leading edge surfaces through a porous skin was demonstrated in tests conducted in the NASA Lewis icing research tunnel using a composite porous leading edge panels. The data obtained were compared with the performance of previously tested stainless steel leading edge with the same geometry. Results show: (1) anti-ice protection of a composite leading edge is possible for all the simulated conditions tested; (2) the glycol flow rates required to achieve anti-ice protection were generally much higher than those required for a stainless steel panel; (3) the low reservoir pressures of the glycol during test runs indicates that more uniform distribution of glycol, and therefore lower glycol flow rates, can probably be achieved by decreasing the porosity of the panel; and (4) significant weight savings can be achieved in fluid ice protection systems with composite porous leading edges. The resistance of composite panels to abrasion and erosion must yet be determined before they can be incorporated in production systems.

Kohlman, D. L.↗
NASA NTRS1981

Elucidation of wear mechanisms by ferrographic analysis

The use of ferrographic analysis in conjunction with light and scanning electron microscopy is described for the elucidation of wear mechanisms taking place in operating equipment. Example of adhesive wear, abrasive wear, corrosive wear, rolling element fatigue, lubricant breakdown, and other wear modes are illustrated. In addition, the use of magnetic solutions to precipitate nonmagnetic debris from aqueous and nonaqueous fluids is described.

Jones, W. R., Jr.↗
NASA NTRS1981

Composite seal for turbomachinery

A gas path seal suitable for use with a turbine engine or compressor is provided. A shroud wearable or abradable by the abrasion of the rotor blades of the turbine or compressor shrouds the rotor blades. A compliant backing surrounds the shroud. The backing is a yieldingly deformable porous material covered with a thin ductile layer. A mounting fixture surrounds the backing.

Bill, R. C.↗
NASA NTRS1982

Harmonic well matter densities and Pauli correlation effects in heavy-ion collisions

A generalized optical model heavy ion reaction theory is extended to include correlation effects between projectile and target constituents according to the Pauli exclusion principle. These correlation effects are significant for accurately predicting cross sections for projectile nucleus abrasions, but are relatively unimportant for determining total and absorption cross sections for heavy ion collisions. For lighter nuclei, predictive capabilities were also improved by developing an analytic method for extracting their nuclear single particle density distributions from experimentally measured harmonic well charge density distributions. This improved theory is compared with previous theoretical predictions and recent experimental results.

Townsend, L. W.↗
NASA NTRS1982

Proceedings of the Low-Cost Solar Array Wafering Workshop

The technology and economics of silicon ingot wafering for low cost solar arrays were discussed. Fixed and free abrasive sawing wire, ID, and multiblade sawing, materials, mechanisms, characterization, and innovative concepts were considered.

Morrison, A. D.↗
NASA NTRS1982

Design and use of multiple blade slurry sawing in a production atmosphere

The technique and uses of the multiple blade slurry (MBS) saw are considered. Multiple bands of steel are arranged in a frame and the frame is reciprocated with the steel bands to a workpiece, while simultaneously applying abrasive at the point of contact. The blades wear slots in the workpiece and progress through the piece resulting in several parts of wafers. The transition to MBA from diamond slicing is justified by savings resulting from minimized kerf losses, minimized subsurface damage, and improved surface quality off the saw. This allows wafering much closer to finished thickness specifications. The current state of the art MBS technology must be significantly improved if the low cost solar array (LSA) goals are to be attained. It is concluded that although MBS will never be the answer to every wafering requirement, the economical production of wafers to LSA project specifications will be achieved.

Lynah, F. P., Jr.↗
NASA NTRS1982

Sensitivity analysis of add-on price estimate for select silicon wafering technologies

The cost of producing wafers from silicon ingots is a major component of the add-on price of silicon sheet. Economic analyses of the add-on price estimates and their sensitivity internal-diameter (ID) sawing, multiblade slurry (MBS) sawing and fixed-abrasive slicing technique (FAST) are presented. Interim price estimation guidelines (IPEG) are used for estimating a process add-on price. Sensitivity analysis of price is performed with respect to cost parameters such as equipment, space, direct labor, materials (blade life) and utilities, and the production parameters such as slicing rate, slices per centimeter and process yield, using a computer program specifically developed to do sensitivity analysis with IPEG. The results aid in identifying the important cost parameters and assist in deciding the direction of technology development efforts.

Mokashi, A. R.↗
NASA NTRS1982

System for slicing wafers

A newly patented process for slicing silicon wafers that has distinct advantages over methods now widely used is described. The primary advantage of the new system is that it allows the efficient slicing of a number of ingots simultaneously at high speed. The cutting action is performed mechanically, most often with diamond particles that are transported to the cutting zone by a fluid vehicle or have been made an integral part of the blade by plating or impregnation. The new system uses a multiple or ganged band saw, arranged and spaced so that each side, or length, segment of a blade element, or loop, provides a cutting function. Each blade is maintained precisely in position by guides as it enters and leaves each ingot. The cutting action is performed with a conventional abrasive slurry composed of diamond grit suspended in an oil- or water-based vehicle. The distribution system draws the slurry from the supply reservoir and pumps it to the injection tubes to supply it to each side of each ingot. A flush system is provided at the outer end of the work-station zone. In order to reduce potential damage, a pneumatically driven flushing fluid is provided.

Source record↗
NASA NTRS1982

Exit chipping in ID sawing of silicon crystals

The processes involved in exit chipping which may occur in the internal diameter diamond sawing of silicon crystals were examined. An interpretation of chipping observations is given in terms of crack propagation as acted upon by the sawing stresses. Since the exit chips are roughly parallel to saw marks, the general locus of the crack must be determined by contact stresses although the exact locus depends on already existing subfractures located in the kerf region which are caused by more than one abrasive particle. The crack starts at either edge since these are weak areas in flexure. In the more extensive "saw fracture", the fracture plane often changes part-way across the slice to be other than parallel to the saw mark because the speed of the crack accelerates beyond the speed of the blade travel; i.e., outstrips the advance of the contact stress field. The influences of various external factors on the opening of the crack are divided into two types: factors that wedge the crack apart and those that bend the slice away from the crystal. From a consideration of these factors, conditions for minimizing exit chipping are defined.

Dyer, L. D.↗