Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONCRETE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

3D printing of calcined clay-limestone-based cementitious materials

This paper aims to investigate the influences of high Portland cement substitutions (>60 wt%) by low-grade calcined clay (CC) and limestone (LF) on 3D concrete printability, stiffness evolution and early-age hydration. Results show that, with the same dosage of admixtures (superplasticizer and viscosity modifier), increasing LF and CC content reduced the slump, flowability and initial material flow rate, and significantly improved the buildability of fresh mixtures, which can be attributed to the reduced water film thickness (WFT). Furthermore, the stiffness evolution and SSA{sub total} development up to the first 3 h were accelerated by increasing CC content, which can also be linked to the change of WFT, and consumption of superplasticizer for the dispersion induced by hydration products. Additionally, the dilution effect on compressive strength and hydration caused by the high cement replacement was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental evidence for the acceleration of slag hydration in blended cements by the addition of CaCl2

Cements with high substitution rates of ground granulated blast furnace slags (GGBS) have the potential to significantly lower CO{sub 2} emissions of concrete, but their early age strength is often below those of traditional OPC cements. One way of mitigating this drawback is to use accelerating admixtures. In this study, the effect of CaCl{sub 2} additions on the hydration of blended cements was investigated by measuring compressive strength, porosity, heat release and propagation of ultrasound in blends containing 70 wt% of GGBS. The onset of formation of aluminate phases was monitored using in-situ XRD. The effect of CaCl{sub 2} on slag hydration was isolated by replacing GGBS by an inert quartz filler. Results showed that compressive strength values at one, two and seven days were increased by 50% by the CaCl{sub 2} addition. The increases in compressive strength corresponded to a reduction in pore space. GGBS hydration contributed to the heat development, structuration and compressive strength of the blended cements from 15 h. The addition of CaCl{sub 2} led to an earlier onset of the GGBS reaction, at around 10 h, and increased the rate of GGBS hydration during the first seven days. The time of onset of the GGBS contribution was also the moment when AFm precipitation started. In CaCl{sub 2}-containing blends, Cl was incorporated in AFm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding geopolymer binder-aggregate interfacial characteristics at molecular level

The interfacial characteristics of geopolymer binder to aggregate composites are poorly understood, especially at molecular level. Herein, molecular models are developed to study, for the first time, the geopolymer-aggregate interface. Chemically, various forms of interfacial bonding are characterized, including Al-O-Si bonding through condensation reactions, NaO and H-bonding. An atomic-level interfacial transition zone (ITZ) is identified, attributed to the concentration of –OH groups. Increasing the Si/Al ratio of geopolymer is found to decrease the ITZ density, but have limited effect on the ITZ width. A heterogeneous diffusion characteristic occurs in geopolymer, due to the weak interfacial interaction. Mechanically, lowering the Si/Al ratio promotes the interfacial strength due to the stronger interfacial interaction and higher cross-linking degree in geopolymer. Under loading the interfacial fracture undergoes three stages: crack propagation, chain bridging (including aluminosilicate and ionic bridging) and breakage. The above atomic-level findings may facilitate a better design of geopolymer concrete in engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Argon broad ion beam sectioning and high resolution scanning electron microscopy imaging of hydrated alite

Highlights: • The native fibrous outer and dense inner C-S-H structure are preserved by using low energy argon broad ion beam sectioning. • Possible artefacts of the preparation and imaging of hydrated alite are shown and discussed. • An approach for a semi automated pore analysis of the obtained high resolution images is demonstrated. Scanning electron microscopy (SEM) imaging is able to visualize micro- to nano-structures of cement and concrete. A prerequisite is that the sample preparation preserves the native structure of the specimen. In this study, argon broad ion beam (BIB) sectioning is compared to state-of-the-art sample preparation (resin embedding, polishing) for hydrated alite. Additionally, it is investigated if during BIB, sample cooling is beneficial to avoid deterioration of cement hydrates. The aim is to quantitatively measure pore size distributions in hardened alite pastes. Therefore, not only optimized sample preparation but also optimized imaging conditions are investigated. Finally, it is demonstrated that by image analysis pores down to a diameter of 5 nm in hydrated alite pastes can be quantitatively analysed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Alkali-silica reaction products and cracks: X-ray micro-tomography-based analysis of their spatial-temporal evolution at a mesoscale

In this study, we propose a laboratory-scale methodology, based on X-ray micro-tomography and caesium (Cs) as a contrast agent, to advance the understanding of cracking due to alkali-silica reaction (ASR) in concrete. The methodology allows achieving a completely non-destructive and time-lapse characterization of the spatial-temporal patterns of both the cracks and the ASR products. While Cs addition slightly accelerated the ASR kinetics, the crack patterns, with and without Cs addition, were statistically equivalent. Cracks with ASR products appeared first in the aggregates, close to the interface with the cement paste. They propagated afterwards towards the aggregates interior. Some products were then extruded for several mm into air voids and cracks in the cement paste. This process suggests that, in the early stage, the ASR products may be a low-viscosity gel that can flow away from the source aggregate and may settle later elsewhere as a rigid phase, upon calcium uptake.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Discontinuous micro-fibers as intrinsic reinforcement for ductile Engineered Cementitious Composites (ECC)

Engineered Cementitious Composites (ECC) have demonstrated superior mechanical and durability performance than conventional concrete. In the micromechanical reinforcing system of ECC, fibers play a pivotal role in establishing the ultrahigh tensile ductility and autogenous crack width control. This article reviews the state-of-the-art of discontinuous micro-fibers as intrinsic reinforcement of ECC regarding technical performance as well as environmental and economic impacts. Mechanical properties of ECC made with different micro-fibers, man-made or natural, and their embodied energy, emissions and material cost, are comprehensively surveyed. Further, studies on fiber hybridization are discussed regarding the combination of different types of fibers to form synergetic reinforcements that mitigate total material cost, and potentially enhance the composite performance. Lastly, recommendations on fiber selections are highlighted and directions for future research are suggested.

42 ENGINEERING↗
DOE OSTI2023

Multi-fidelity physics-informed machine learning for probabilistic damage diagnosis

Machine learning (ML) models are gaining popularity in structural health monitoring (SHM) because of their ability to learn the complex relationship between damage and sensor data. However, the lack of sufficient experimental data for structures with different degrees of damage is a key problem in training ML models for SHM. This problem can be alleviated by using physics-based models to generate the required training data to build physics-informed ML (PIML) models for SHM. However, it takes significant computational effort to perform enough high-fidelity simulations of the diagnostic test. It is thus desirable to know whether the available computational resource budget should be expended on numerous low-fidelity physics simulations, or a small number of high-fidelity simulations, or their combination. In this paper, we investigate this aspect of generating adequate training data for PIML, by constructing multi-fidelity PIML models. We evaluate the performance of several PIML models, trained with different amounts of low-fidelity and high-fidelity data, in locating hidden cracks in concrete structures using a nonlinear dynamics-based diagnosis technique. Here, we find that high-fidelity physics simulations that do not cover the (test and damage) parameter space do not improve the performance of diagnostic PIML models built using data from many low-fidelity physics simulations.

42 ENGINEERING↗
DOE OSTI2021

Grizzly Development for Light Water Reactor and Advanced Reactor Applications in Fiscal Year 2021

This report summarizes work performed during Fiscal Year (FY) 2021 at Idaho National Laboratory (INL) for the U.S. Department of Energy’s Nuclear Engineering Advanced Modeling and Simulation (NEAMS) program for the Structural Materials and Chemistry Technical Area in the work package entitled “MS-21IN050106 - Structural Materials - INL.” This effort mainly focused on development and application of capabilities for engineering-scale analysis of nuclear reactor structural components in the Grizzly and BlackBear codes. These efforts include performance improvements and application of models for high-temperature component response, cluster dynamics modeling of precipitation in light water reactor pressure vessel steel, engineering-scale capability development in the areas of concrete simulation and reactor pressure vessel analysis, and preparation for and conducting an independent assessment of the adherence of these codes to software quality standards.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Biopolymer Modified Cementitious Systems with Radically Superior Strength and Durability

This project was a pioneering study of the effect of nanochitin additives on setting time, rheological, and mechanical properties of cementitious materials. Chitin is the second most abundant biopolymer in nature after cellulose and is readily available from byproducts of the growing seafood industry. In this study, chitin powder from shrimp shells was processed into chitin nanocrystals (ChNCs) and chitin nanofibers (ChNFs). Ch-Cs delayed initial and final set times with their high ionic surface charges likely by electrostatic repulsion. The viscosity of fresh cement paste increased with Ch-NFs, while Ch-NCs did not significantly affect rheological properties. The distinct effects of the two nanochitin forms are attributed to the mobility of the different morphologies of the rod-like ChNCs vs. the entangled and restrained network of the ChNFs. Nanochitin forms showed encouraging results by significantly increasing flexural strength by ~40% at the optimum concentration of 0.05 wt% and significant increases in fracture energy. These bio-additives were found promising and future studies should continue to evaluate their use in concrete.

36 MATERIALS SCIENCE↗
DOE OSTI2023

New England Aqua Ventus I: 100% Hull Design (Final Technical Report)

This report serves as the final technical report for the US Department of Energy (DOE) award DE-EE0006713 (Award 6713). The project is titled “New England Aqua Ventus I Offshore Wind Advanced Technology Demonstration Project 100% Front-End Engineering and Design (FEED)”. The New England Aqua Ventus I (NEAV) project demonstrates a unique prestressed concrete semi-submersible floating hull technology, called VolturnUS. The technology is applicable to harness nearly 60% of the US offshore wind resource within 50 miles of the coast. The hull will be demonstrated at full-scale with a commercial scale wind turbine connected to the grid in the Northeast US off Monhegan Island, Maine for 20 years.

17 WIND ENERGY↗
DOE OSTI2024

Finding of adverse effect and proposed mitigation for the removal of three primary resources and twenty-four accessory resources within the mercury historic district, area 23, nevada national security site, nye county, nevada

The U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) proposes the removal of three primary resources and 24 accessory resources in Mercury on the Nevada National Security Site (NNSS) in Nye County, Nevada. The majority of the resources are concrete pads that have previously been recorded as either primary resources or accessory resources thereof within the Mercury Historic District (MHD). They represent the former locations of environmental support program buildings including a greenhouse (MHD Resource C312), warehouses (Resource C293), offices (Resource C314), dormitories (Resource C298), and two of unknown purpose (Resource C292). The other resources include a buried storage tank and sidewalks.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Improved digital construction binder solution utilizing calcium aluminate additive for Infrastructure Scale Additive Manufacturing

Oak Ridge National Laboratory (ORNL) worked with Kerneos Inc., a Division of Imerys USA, Inc. to develop an improved digital construction binder using calcium aluminate additives produced by Kerneos along with locally available concrete materials. When the two-stage (2K) binder formulation was added to commercially available Portland Limestone Cement and sand to form a digital construction mortar, its strength exceeded a number of commercially available digital construction binders both at early and later ages. At the same time, the developed formulation showed precise control of setting time after addition and showed very low shrinkage making it a strong, reliable, and easily customizable alternative to fixed proprietary digital construction binders.

36 MATERIALS SCIENCE↗
DOE OSTI2025

3D Printing of Cement-Based Materials Using Seawater for Simulated Marine Environments

Global demand for adaptable and rapidly deployable construction solutions in offshore, coastal, and fluvial environments continues to rise, driven by pressing needs to develop energy platforms, improve coastal resilience, and support emergency response in the face of natural disasters. Increased investment in human-made coastal infrastructure, such as piers, support structures for power lines, offshore wind farms, and seawall protection systems, further underscores this trend. This study investigates the development of printable concrete mixtures for underwater environments using seawater as a replacement for freshwater, using a 3D printing syringe-based extrusion system. The effect of seawater addition and the printing medium (in air vs. underwater) was assessed via rheological and mechanical performance characterization. The results indicate rheological properties are favorable for seawater adoption by producing mixtures with higher yield stress and viscosity with the same levels of admixtures used for freshwater. Seawater-based mixtures demonstrated superior dimensional stability compared to freshwater counterparts, maintaining cross-sectional geometry, while compressive strength results showed no statistical differences between in-air and underwater samples. However, flexural strength was significantly influenced by geometry and printing medium. These findings establish critical rheological parameters for printable underwater mixtures and highlight the need for optimized curing strategies and layer bonding techniques to improve interfacial strength in underwater 3D printing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Void-Engineered Metamaterial Delay Line with Built-In Impedance Matching for Ultrasonic Applications

Metamaterials exhibit unique ultrasonic properties that are not always achievable with traditional materials. However, the structures and geometries needed to achieve such properties are often complex and difficult to obtain using common fabrication techniques. In the present research work, we report a novel metamaterial acoustic delay line with built-in impedance matching that is fabricated using a common 3D printer. Delay lines are commonly used in ultrasonic inspection when signals need to be separated in time for improved sensitivity. However, if the impedance of the delay line is not perfectly matched with those of both the sensor and the target medium, a strong standing wave develops in the delay line, leading to a lower energy transmission. The presented metamaterial delay line was designed to match the acoustic impedance at both the sensor and target medium interfaces. This was achieved by introducing graded engineered voids with different densities at both ends of the delay line. The measured impedances of the designed metamaterial samples show a good match with the theoretical predictions. The experimental test results with concrete samples show that the acoustic energy transmission is increased by 120% and the standing wave in the delay line is reduced by over a factor of 2 compared to a commercial delay line.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Determination of Elastic Coefficients for a Composite with Crossing Steel - 20086

For a composite material with an embedding of crossing reinforcement bars, the elastic coefficients are calculated by solving a boundary-value problem (elastostatic problem). The background material is concrete whereas the bars are made of steel. The bars cross each other horizontally at a right angle. The boundary-value problem is solved numerically by using 3-D quadratic basis functions in ABAQUS{sup R}. Under external shear loading conditions, the effective elastic coefficients on the macroscale are quite larger for a cross-section in which the bars are immediately below the ones in the cross-section normal to it. The shear modulus in the off-plane direction is about one and half times larger than that in the in-plane direction. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Amphiphilic Block Copolymers for Flocculation and Hydrophobization of Legacy Waste Suspensions in Flotation Driven Dewatering Operations

There exists a degrading legacy fuel pond at the Sellafield site (UK), known as the First-Generation Magnox Storage Pond (FGMSP). After being placed into a passive care and maintenance regime resulting in a long storage period, the fuel rods, primarily their cladding, corroded in the pond forming magnesium hydroxide based sludges and suspended material. These ponds are a grave concern to the British government in terms of hazard and risk reduction. Therefore, decommissioning of these ponds is a top priority beginning with the contaminant retrievals process [1]. The pond has accumulated significant quantities of waste materials amongst the skips of fuel, including but not limited to: large inventories of corroded Magnox sludge, fuel rod fragments, metal fragments (from fuel skips), concrete degradation products (from the pond infrastructure), wind-blown sand, and other materials such as bird guano and animal remains. This challenge requires a chemically robust technology to complete sludge retrievals [2]. As nuclear is different, a more stringent process operation criteria is required. From the criteria, flotation was selected as a viable technology. Flotation involves the application of collector molecules which modify the hydrophobicity of suspended particles allowing them to adsorb to rising bubbles. As some particles lack inertia for flotation due to their size, dual flocculant/collector agents can be deployed for greater particle recovery, in this case, amphiphilic diblock copolymers. Two copolymers of Poly(acrylic acid)-b-poly(n-butyl acrylate) (or PAA-b-PnBA), of different hydrophobic chain lengths (PBA) were synthesized for flotation campaigns. Flotation has shown promise to be a valuable rapid dewatering strategy for decommissioning of legacy waste ponds whilst upholding the required operational criteria. This research has shown: PAA-b-PnBA copolymers promote flocculation of Mg(OH){sub 2} particulates. Diblock copolymers retain more fluid than traditional surfactant based collectors wrt. relative particulate recovery performance- where longer PnBA chain length polymers performed best. Performance appears to be hydrodynamically limited due to over-flocculation of Mg(OH){sub 2}. Potential to combine with sedimentation for high particle recovery with low fluid carryover.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗