SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Report describes Simulator for Imager for Mars Pathfinder (SIMP) computer program. SIMP generates "virtual reality" display of view through video camera on Mars lander spacecraft of Mars Pathfinder mission, along with display of pertinent textual and graphical data, for use by scientific investigators in planning sequences of activities for mission.
A report presents a study of five modeling and diagnostic computer programs considered for use in an integrated vehicle health management (IVHM) system during testing of liquefying-fuel hybrid rocket engines in the Hybrid Combustion Facility (HCF) at NASA Ames Research Center. Three of the programs -- TEAMS, L2, and RODON -- are model-based reasoning (or diagnostic) programs. The other two programs -- ICS and IMS -- do not attempt to isolate the causes of failures but can be used for detecting faults. In the study, qualitative models (in TEAMS and L2) and quantitative models (in RODON) having varying scope and completeness were created. Each of the models captured the structure and behavior of the HCF as a physical system. It was noted that in the cases of the qualitative models, the temporal aspects of the behavior of the HCF and the abstraction of sensor data are handled outside of the models, and it is necessary to develop additional code for this purpose. A need for additional code was also noted in the case of the quantitative model, though the amount of development effort needed was found to be less than that for the qualitative models.
A report discusses the continuing development of Windows Interface for Nominal Displacement Selection (WINDS), a computer program for automated analysis of images of the Sun and planets acquired by scientific instruments aboard spacecraft. WINDS is intended to afford capabilities for identification of features, measurement of displacements and velocities, analysis of terrain and of atmospheres, and synthesis of animation sequences of images of terrains and atmospheres from small sets of samples by use of velocity-based interpolation. A major element of WINDS will be a nonlinear correlator capable of tracking small features in complex image sequences. For dynamic image sequences, the correlator will enable compression of data by factors >100. In processing image data, WINDS will take account of such factors as texture in image data, rotation of features during measurement intervals, effects of viewing and solar illumination angles, and vertical structures of atmospheres. WINDS will also take account of positions, aiming directions, and fields of view of cameras to determine three-dimensional feature structures by use of triangulation and stereoscopic analysis techniques.
Multi-mission Encrypted Communication System (MECS) is a computer program that enables authorized, geographically dispersed users to gain secure access to a common set of data files via the Internet. MECS is compatible with legacy application programs and a variety of operating systems. The MECS architecture is centered around maintaining consistent replicas of data files cached on remote computers. MECS monitors these files and, whenever one is changed, the changed file is committed to a master database as soon as network connectivity makes it possible to do so. MECS provides subscriptions for remote users to automatically receive new data as they are generated. Remote users can be producers as well as consumers of data. Whereas a prior program that provides some of the same services treats disconnection of a user from the network of users as an error from which recovery must be effected, MECS treats disconnection as a nominal state of the network: This leads to a different design that is more efficient for serving many users, each of whom typically connects and disconnects frequently and wants only a small fraction of the data at any given time.
The Autonomous Power System (APS) brassboard is a 20 kHz power distribution system which has been developed at NASA Lewis Research Center, Cleveland, Ohio. The brassboard exists to provide a realistic hardware platform capable of testing artificially intelligent (AI) software. The brassboard's power circuit topology is based upon a Power Distribution Control Unit (PDCU), which is a subset of an advanced development 20 kHz electrical power system (EPS) testbed, originally designed for Space Station Freedom (SSF). The APS program is designed to demonstrate the application of intelligent software as a fault detection, isolation, and recovery methodology for space power systems. This report discusses both the hardware and software elements used to construct the present configuration of the brassboard. The brassboard power components are described. These include the solid-state switches (herein referred to as switchgear), transformers, sources, and loads. Closely linked to this power portion of the brassboard is the first level of embedded control. Hardware used to implement this control and its associated software is discussed. An Ada software program, developed by Lewis Research Center's Space Station Freedom Directorate for their 20 kHz testbed, is used to control the brassboard's switchgear, as well as monitor key brassboard parameters through sensors located within these switches. The Ada code is downloaded from a PC/AT, and is resident within the 8086 microprocessor-based embedded controllers. The PC/AT is also used for smart terminal emulation, capable of controlling the switchgear as well as displaying data from them. Intelligent control is provided through use of a T1 Explorer and the Autonomous Power Expert (APEX) LISP software. Real-time load scheduling is implemented through use of a 'C' program-based scheduling engine. The methods of communication between these computers and the brassboard are explored. In order to evaluate the features of both the brassboard hardware and intelligent controlling software, fault circuits have been developed and integrated as part of the brassboard. A description of these fault circuits and their function is included. The brassboard has become an extremely useful test facility, promoting artificial intelligence (AI) applications for power distribution systems. However, there are elements of the brassboard which could be enhanced, thus improving system performance. Modifications and enhancements to improve the brassboard's operation are discussed.
ION is a system of ground support software for the ion and neutral mass spectrometer (INMS) instrument aboard the Cassini spacecraft. By incorporating commercial off-the-shelf database, Web server, and Java application components, ION offers considerably more ground-support-service capability than was available previously. A member of the team that operates the INMS or a scientist who uses the data collected by the INMS can gain access to most of the services provided by ION via a standard pointand click hyperlink interface generated by almost any Web-browser program running in almost any operating system on almost any computer. Data are stored in one central location in a relational database in a non-proprietary format, are accessible in many combinations and formats, and can be combined with data from other instruments and spacecraft. The use of the Java programming language as a system-interface language offers numerous capabilities for object-oriented programming and for making the database accessible to participants using a variety of computer hardware and software.
Methods of modeling the detection time or latency period of a hardware fault in a digital system are proposed that explain how a computer detects faults in a computational mode. The objectives were to study how software reacts to a fault, to account for as many variables as possible affecting detection and to forecast a given program's detecting ability prior to computation. A series of experiments were conducted on a small emulated microprocessor with fault injection capability. Results indicate that the detecting capability of a program largely depends on the instruction subset used during computation and the frequency of its use and has little direct dependence on such variables as fault mode, number set, degree of branching and program length. A model is discussed which employs an analog with balls in an urn to explain the rate of which subsequent repetitions of an instruction or instruction set detect a given fault.
A technique for real-time estimation of stability and control derivatives (derivatives of moment coefficients with respect to control-surface deflection angles) was used to support a flight demonstration of a concept of an indirect-adaptive intelligent flight control system (IFCS). Traditionally, parameter identification, including estimation of stability and control derivatives, is done post-flight. However, for the indirect-adaptive IFCS concept, parameter identification is required during flight so that the system can modify control laws for a damaged aircraft. The flight demonstration was carried out on a highly modified F-15 airplane (see Figure 1). The main objective was to estimate the stability and control derivatives of the airplane in nearly real time. A secondary goal was to develop a system to automatically assess the quality of the results, so as to be able to tell a learning neural network which data to use. Parameter estimation was performed by use of Fourier-transform regression (FTR) a technique developed at NASA Langley Research Center. FTR is an equation- error technique that operates in the frequency domain. Data are put into the frequency domain by use of a recursive Fourier transform for a discrete frequency set. This calculation simplifies many subsequent calculations, removes biases, and automatically filters out data beyond the chosen frequency range. FTR as applied here was tailored to work with pilot inputs, which produce correlated surface positions that prevent accurate parameter estimates, by replacing half the derivatives with predicted values. FTR was also set up to work only on a recent window of data, to accommodate changes in flight condition. A system of confidence measures was developed to identify quality-parameter estimates that a learning neural network could use. This system judged the estimates primarily on the basis of their estimated variances and of the level of aircraft response. The resulting FTR system was implemented in the Simulink software system and auto-coded in the C programming language for use on the Airborne Research Test System (ARTS II) computer installed in the F-15 airplane. The Simulink model was also used in a control room that utilizes the Ring Buffered Network Bus hardware and software, making it possible to evaluate test points during flights. In-flight parameter estimation was done for piloted and automated maneuvers, primarily at three test conditions. Figure 2 shows results for pitching moment due to symmetric stabilator actuations for a series of three pitch doublet maneuvers (in a doublet maneuver, a command to change attitude in a given direction by a given amount is followed immediately by a command to change attitude in the opposite direction by the same amount). A time window of 5 seconds was used. The portions of the curves shown in red are those that passed the confidence tests. The technique showed good convergence for most derivatives for both kinds of maneuvers - typically within a few seconds. The confidence tests were marginally successful, and it would be necessary to refine them for use in an IFCS.
The results of a study of test data taken on the simplex strapdown navigation system were presented. That system consisted of the following components: strapdown platform, altimeter, digital computer, tape recorder, typewriter, and power source. The objective of these tests was to isolate error sources which may cause degradation of the system's accuracy and to recommend appropriate changes to the system test procedures or computer software. The following recommendations were made: (1) addition of a gyro compassing alignment program into the navigation program, (2) addition of line drivers at the signal processor end of the transmission line, (3) need for extensive laboratory testing to determine sensor misalignments, biases, and scale factors, (4) need to stabilize the power source to prevent transients during power transfer, (5) need to isolate and eliminate the source of the large noise inputs.
A computer code, NASCAP (NASA Charging Analyzer Program), has been developed by Systems, Science and Software under contract to NASA-LeRC to simulate the charging of a complex spacecraft in geosynchronous orbit. The capabilities of the NASCAP code include a fully three-dimensional solution of Poisson's equation about an object having considerable geometrical and material complexity, particle tracking, shadowing in sunlight, calculation of secondary emission, backscatter and photoemission, and graphical output. A model calculation shows how the NASCAP code may be used to improve our understanding of the spacecraft-plasma interaction.
An overview of the knowledge acquisition component of the Bauhaus, a prototype computer aided software engineering (CASE) workstation for the development of domain-specific automatic programming systems (D-SAPS) is given. D-SAPS use domain knowledge in the refinement of a description of an application program into a compilable implementation. The approach to the construction of D-SAPS was to automate the process of refining a description of a program, expressed in an object-oriented domain language, into a configuration of software parts that implement the behavior of the domain objects.
The desire to integrate newly available, graphically-oriented Computed Aided Software Engineering (CASE) tools with existing software design approaches is changing the way Program Design Language (PDL) or Process Description Language is used for large system development. In the approach documented here, Software Engineers use graphics tools to model the problem and to describe high level software design in diagrams. An Ada-based PDL is used to document low level design. Some results are provided along with an analysis for each of three smaller General Electric (GE) Ada development projects that utilized variations on this approach. Finally some considerations are identified for larger scale implementation.
Our intuition is that comprehension of visual representations is often quicker than of equivalent text. In the work described in this paper, we explore the application of this intuition to programming languages. The goal of this project is to create visual representation of segments of computer programs that improve the maintenance and reusability of this code. We describe a software tool, a program browser, that provides a visual representation of the function call graph of any C program. This tool is the first in a series of tools that aids program comprehension, making reuse of existing programs more likely. The development of the program browser is itself an example of code reuse as described in the section on implementation. Although our intuition is that some visual display of programs aid understandability, we are looking for experimental verification. Several human factors experiments in this area have contradicted this intuition. We describe reasons for these contradictions, and potential solutions to overcome them.
The potential for serious health risks from solar particle events (SPE) and galactic cosmic rays (GCR) is a critical issue in the NASA strategic plan for the Human Exploration and Development of Space (HEDS). The excess cost to protect against the GCR and SPE due to current uncertainties in radiation transmission properties and cancer biology could be exceedingly large based on the excess launch costs to shield against uncertainties. The development of advanced shielding concepts is an important risk mitigation area with the potential to significantly reduce risk below conventional mission designs. A key issue in spacecraft material selection is the understanding of nuclear reactions on the transmission properties of materials. High-energy nuclear particles undergo nuclear reactions in passing through materials and tissue altering their composition and producing new radiation types. Spacecraft and planetary habitat designers can utilize radiation transport codes to identify optimal materials for lowering exposures and to optimize spacecraft design to reduce astronaut exposures. To reach these objectives will require providing design engineers with accurate data bases and computationally efficient software for describing the transmission properties of space radiation in materials. Our program will reduce the uncertainty in the transmission properties of space radiation by improving the theoretical description of nuclear reactions and radiation transport, and provide accurate physical descriptions of the track structure of microscopic energy deposition.
Under an SBIR (Small Business Innovative Research) contract with Goddard Space Flight Center, (NAS5-32730), Frederick A. Costello, Inc., has developed a low cost computer program for integrating thermal modeling with other engineering disciplines. TCON(tm) Concurrent Engineering Software enables graphical user-interface programs to create three dimensional models. This technology reduces time, and facilitates accuracy while performing these applications. TCON(tm) has been sold to NASA and major US industries.
AiResearch Manufacturing Company, a division of the Garrett Corporation, is engaged in manufacturing a broad variety of products of the aerospace, energy, metals, transit, and marine industries. Products such as fuel controls and rotating accessories for gas turbines are produced by another Garrett division. Computerized analysis is employed to determine how well proposed seals will stand up to stress. For such analysis, AiResearch uses a computer program supplied by COSMIC known as VISCEL. Program saves engineers time in development of software and contributes to improved efficiency in seal analysis.
One of NASA's key goals is to increase the safety and reduce the cost of space transportation. Thus, a key element of NASA's new Integrated Space Transportation Plan is to develop new propulsion, structures, and operations for future generations of reusable launch vehicles (RLVs). As part of this effort to develop the next RLV, the ClCT Program's Computing, Networking, and Information Systems (CNIS) Project is developing and demonstrating collaborative software technologies that use the collective power of the NASA Grid to accelerate spacecraft design. One of these technologies, called AeroDB, automates the execution and monitoring of computational fluid dynamics (CFD) parameter studies on the NASA Grid. About the NASA Grid The NASA Grid, or Information Power Grid,. is being developed to leverage the distributed resources of NASA's many computers. instruments, simulators, and data storage systems. The goal is to use these combined resources to sdve difficult NASA challenges, such as iimulating the entire flight of a space vehicle from ascent to descent.To realize the vision of the NASA Grid, the CNIS Project is developing the software framework and protocols for building domain-specific environments and interfaces, new Grid services based on emerging industry standards, and advanced networking and computing testbeds to support new Grid-based applications such as AeroDB.
This presentation discusses fractured leads on field-programmable gate array (FPGA) during flight vibration. Actions taken to determine root cause and resolution of the failure include finite element analysis (FEA) and vibration testing and scanning electron microscopy (with X-ray microanalysis) and energy dispersive spectrometry (SEM/EDS) failure assessment. Bonding methods for surface mount parts is assessed, including critical analysis and assessment of random fatigue damage. Regarding ceramic quad flat pack (CQFP) lead fracture, after disassembling the attitude control electronics (ACE) configuration, photographs showed six leads cracked on FPGA RTSX72SU-1 CQ208B package located on the RWIC card. An identical package (FPGA RTSX32SU-1 CQ208B) mounted on the RWIC did not results in cracked pins due to vibration. FPGA lead failure theories include workmanship issues in the lead-forming, material defect in the leads of the FPGA packages, and the insecure mounting of the board in the card guides, among other theories. Studies were conducted using simple calculations to determine the response and fatigue life of the package. Shorter packages exhibited more response when loaded by out-of-plane displacement of PCB while taller packages exhibit more response when loaded by in-plane acceleration of PCB. Additionally, under-fill did not contribute to reducing stress in leads due to out-of-plane PCB loading or from component twisting, as much as corner bonding. The combination of corner bond and under-fill is best to address mechanical and thermal S/C environment. Test results of bonded parts showed reduced (dampened) amplitude and slightly shifted peaks at the un-bonded natural frequency and an additional response at the bonded frequency. Stress due to PCBB out-of-plane loading was decreased on in the corners when only a corner bond was used. Future work may address CQFP fatigue assessment, including the investigation of discrepancy in predicted fatigue damage, as well as comparing fatigue life and fatigue damage cycle ration computed using FEA and Miner's rule to results from a fatigue assessment software program.