Search NASA⌕ Search

SEARCH · Search NASA

Results for “FORGING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Co-extrusion of Discontinuously, Non-centric Steel-reinforced Aluminum

The process of manufacturing discontinuously non-centric steel reinforced aluminum by means of co-extrusion has been examined. By this process semi-finished reinforced profiles can be fabricated for further treatment through forging techniques. Therefore, steel reinforcement elements consisting of E295GC were inserted into conventional aluminum billets and co-extruded into two different solid profiles; a rectangle one by an extrusion ratio of 10.1:1 and a round one by 4.8:1. The used aluminum alloy is EN AW-6060. The billet temperature as well as the ram speed were varied to investigate their influence on the position of the reinforcement elements inside the strand. The measurement was done by a video measurement system, called Optomess A250, after milling off the strand. The distances between the elements in longitudinal direction were nearly constant, apart from the rear part of the strand. The same was observed for the distance of the steel elements to the profile edge. This due to the inhomogeneous material flow in the transverse weld, related to the billet-to-billet extrusion. The rotation of the reinforcement elements occurs because the elements flow nearby the shear zone. Further, micrographs were made to investigate the embedding situation and the grain size distribution. The embedding of the reinforcement elements were good in the solid round profile, but in the rectangle profile were found some kind of air pocket. The grain size of the aluminum alloy close to the steel elements is much smaller than in the other parts of the solid round profile.

36 MATERIALS SCIENCE↗

Investigation of the Workability and Response of Ti-6Al-4V Titanium alloys at Lower Elevated Temperature and Higher Strain Rate

Titanium and its alloys have a wide range of applications in various industries such as aerospace, medical, automotive and even commercial products. However, formability of titanium alloys has always been an issue. This study presents the results of an investigation on the workability and response of Ti-6Al-4V deformed at different strain rates and lower elevated temperatures with different initial microstructures. Compression tests of cylindrical specimens were performed at various temperatures (300 deg. C, 400 deg. C, 450 deg. C, 500 deg. C) and at different strain rates (0.001 s{sup -1}, 0.02 s{sup -1} and 0.1 s{sup -1}). The effects of strain rate, temperature and initial microstructure on the workability of the Ti alloy were investigated. Based on these experimental results, workability maps for the respective initial microstructures were developed. Results showed that temperature played an important role in the formability of Ti-6Al-4V titanium alloys unlike strain rate. In addition, feasibility study on Multi-Directional Forging (MDF) was performed and positive results were obtained. It was demonstrated that Ti-6Al-4V titanium alloys can undergo severe plastic deformation at lower elevated temperature (400-500 deg. C) and at a higher strain rate of 0.1 s{sup -1}.

36 MATERIALS SCIENCE↗

Study of Forming of Magnesium Alloy by Explosive Energy

Magnesium alloy is an attractive next generation material due to its high specific strength with low weight. However, magnesium alloys has few slip lines with close-packed hexagonal lattice, and generally poor ductility at room temperature, therefore it is difficult to form this material by cold forging. It is well known that the speed of deformation of metallic materials rapidly changes at the high strain rate. For some metallic materials, it is reported that the ductility also increases at the high strain rate with this speed effect. In this study, a series of high speed impulsive compressive tests were carried. By using explosives for shock wave loading, the velocity in this experiment reached 100 m/s that can't be easily obtained in normal experiment. In this paper, the possibility of forming the AZ31 extrusion magnesium alloy using explosive-impulsive pressure is investigated. And improved ductility by the effect of high-rate deformation is observed with this alloy.

36 MATERIALS SCIENCE↗

Physical model assisted probability of detection in nondestructive evaluation

Nondestructive evaluation is used widely in many engineering and industrial areas to detect defects or flaws such as cracks inside parts or structures during manufacturing or for products in service. The standard statistical model is a simple empirical linear regression between the (possibly transformed) signal response variables and the (possibly transformed) explanatory variables. For some applications, such a simple empirical approach is inadequate. An important alternative approach is to use knowledge of the physics of the inspection process to provide information about the underlying relationship between the response and explanatory variables. Use of such knowledge can greatly increase the power and accuracy of the statistical analysis and enable, when needed, proper extrapolation outside the range of the observed explanatory variables. This paper describes a set of physical model-assisted analyses to study the capability of two different ultrasonic testing inspection methods to detect synthetic hard alpha inclusion and flat-bottom hole defects in a titanium forging disk.

42 ENGINEERING↗

Improved detection of rough defects for ultrasonic NDE inspections based on finite element modeling of elastic wave scattering

Defects which posses rough surfaces greatly affect ultrasonic wave scattering behaviour, often reducing the magnitude of reflected signals. Ultrasonic inspections rely upon this response for detecting and sizing flaws. For safety critical components reliable characterisation is crucial. Therefore, providing an accurate means to predict reductions in signal amplitude is essential. An extension of Kirchhoff theory has formed the basis for the UK power industry inspection justifications. However, it is widely recognised that these predictions are pessimistic owing to analytical approximations. A numerical full field modelling approach does not fall victim to such limitations. Here, a Finite Element model is used to aid in setting a non-conservative reporting threshold during the inspection of a large pressure vessel forging that might contain embedded rough defects. The ultrasonic response from multiple rough surfaces defined by the same statistical class is calculated for normal incident compression waves. The approach is validated by comparing coherent scattering with predictions made by Kirchhoff theory. At lower levels of roughness excellent agreement is observed, whilst higher values confirm the pessimism of Kirchhoff theory. Furthermore, the mean amplitude in the specular direction is calculated. This represents the information obtained during an inspection, indicating that reductions due to increasing roughness are significantly less than the coherent component currently being used.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Analysis of critically refracted longitudinal waves

Fabrication processes, such as, welding, forging, and rolling can induce residual stresses in metals that will impact product performance and phenomena such as cracking and corrosion. To better manage residual stress tools are needed to map their distribution. The critically refracted ultrasonic longitudinal (LCR) wave is one such approach that has been used for residual stress characterization. It has been shown to be sensitive to stress and less sensitive to the effects of the texture of the material. Although the LCR wave is increasingly widely applied, the factors that influence the formation of the LCR beam are seldom discussed. This paper reports a numerical model used to investigate the transducers' parameters that can contribute to the directionality of the LCR wave and hence enable performance optimization when used for industrial applications. An orthogonal test method is used to study the transducer parameters which influence the LCR wave beams. This method provides a design tool that can be used to study and optimize multiple parameter experiments and it can identify which parameter or parameters are of most significance. The simulation of the sound field in a 2-D 'water-steel' model is obtained using a Spatial Fourier Analysis method. The effects of incident angle, standoff, the aperture and the center frequency of the transducer were studied. Results show that the aperture of the transducer, the center frequency and the incident angle are the most important factors in controlling the directivity of the resulting LCR wave fields.

42 ENGINEERING↗

Tensile properties of the modified 13Cr martensitic stainless steels

This paper reports the influence of Mo and Ni on the tensile properties of the modified 13Cr martensitic stainless steels in tempered condition. Four steels with different content of Mo and Ni were prepared by induction melting followed by hot forging, quenching and tempering. The experimental results showed that the addition of about 1% and 3% Mo has a beneficial effect to increase both the tensile strength and the elongation of the steels. On the contrary, the addition of about 3% Ni into the martensitic stainless steel results in decreasing of both the tensile strength and the elongation. Among the alloys investigated the 13Cr3Mo type steel exhibited largest tensile strength of 1348 MPa and largest elongation of 12%. The observation on the tensile fractured surfaces by using scanning electron microscope supported these findings.

36 MATERIALS SCIENCE↗

A proposed U.S./China theoretical/experimental collaborative effort on baryon resonance extraction

In this paper we discuss the reasons for our work towards establishing a new collaboration between Jefferson Lab (JLab) and the Institute of High Energy Physics (IHEP) in Beijing. We seek to combine experimentalists and theorists into a dedicated group focused on better understanding the current and future data from JLab and from the Beijing Electron Positron Collider (BEPC). Recent JLab results on the extraction of single- and double-polarization observables in both the 1{pi}- and 2{pi}-channel show their high sensitivity to small production amplitudes and therefore their importance for the extraction of resonance parameters. The Beijing Electron Spectrometer (BES) at the BEPC has collected high statistics data on J/{Psi} production. Its decay into baryon-antibaryon channels offers a unique and complementary way of probing nucleon resonances. The CEBAF Large Acceptance Spectrometer, CLAS, has access to N* form factors at high Q{sup 2}, which is advantageous for the study of dynamical properties of nucleon resonances, while the low-background BES results will be able to provide guidance for the search for less-dominant excited states at JLab. Moreover, with the recently approved experimental proposal Nucleon Resonance Studies with CLAS12 and the high-quality data streaming from BES-III and CLAS, the time has come for forging a new Trans-Pacific collaboration of theorists and experimentalists on NSTAR physics.

43 PARTICLE ACCELERATORS↗

2019 Geothermal Design Challenge TM Overview

The U.S. Department of Energy (DOE) Geothermal Technologies Office (GTO), in partnership with the Frontier Observatory for Research in Geothermal Energy (FORGE) and the Idaho National Laboratory (INL), invited high school and university (undergraduate and graduate) teams to explore the future of geothermal energy and visualize the world of geothermal energy by participating in the 2019 Geothermal Design Challenge™. Teams of 2 or 3 members researched data, interpreted information and created a data visualization portfolio that told a compelling story about geothermal energy by answering the challenge question, “Where do you target your next production well to maximize geothermal reservoir performance?” The purpose of this document is to provide an overview of how the 2019 Geothermal Design Challenge™ was organized and conducted.

15 GEOTHERMAL ENERGY↗

2019 accomplishments: degradation of mechanical properties in structural metals and welds for FTS reservoirs

This report documents work in 2019 at SRNL in support of the Aging and Lifetimes program. Specimens for fracture toughness testing were prepared in prior years by thermally pre-charging samples, provided by Sandia National Laboratories, of welded types 304L and 21-6-9 stainless steels. These samples were pre-charged in 2017. The fracture toughness of the first aged specimens was measured and compared to historical data. The measurements of the 304L and 21-6-9 weld and particularly HAZ represent some of the first fracture data relevant to modern GTS reservoirs. This work represents an on-going collaboration between SRNL and SNL to understand tritium embrittlement of structural metals in Gas Transfer System reservoirs which informs lifetime assessments. Continued testing was conducted on ongoing historical studies, including the effects of very long-term aging, and the relative performance of differently forged stockpile relevant 304L and 316L samples. New samples were pre-charged with tritium and placed in a freezer for an aging study to allow helium to build into the material. The precharged samples consist of smooth and notched tensile samples of 304L stainless steel, as well as tube tensile samples of different thermal treatments supplied by Sandia National Laboratories. Their charging marks the beginning of a new sequence of studies to explore fundamental deformation mechanisms underpinning tritium embrittlement. At predesignated times, samples will be removed from aging and tested to provide data which will help develop an understanding of material degradation with increasing aging time. Also documented is progress in employing various advanced characterization techniques including high resolution electron microscopy, thermally programed desorption, and small angle x-ray scattering, as well as facilities renovations and equipment procurements in support of sustained tritium impacts on materials program at SRNL.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Lamination Model for Pressure-Assisted Sintering of Multilayered Porous Structures

This work describes a lamination model for pressure-assisted sintering of thin, multilayered, and porous structures based on the linear viscous constitutive theory of sintering and the classical laminated plate theory of continuum mechanics. A constant out-of-plane normal stress is assumed in the constitutive relation. The lamination relations between the force/moment resultants and the strain/curvature rates are presented. Numerical simulations were performed for a symmetric tri-layer laminate consisting of a 10% gadolinia doped ceria (Ce 0.9 Gd 0.1 O 1.95-δ ) composite structure, where porous layers were adhered to the top and bottom of a denser layer under uniaxially-applied pressures and the sinter forging conditions. The numerical results show that, compared with free sintering, the applied pressure can significantly reduce the sintering time required to achieve given layer thicknesses and porosities. Unlike free sintering, which results in a monotonic decrease of the laminate in-plane dimension, pressure-assisted sintering may produce an in-plane dimension increase or decrease, depending on the applied pressure and sintering time. Finally, the individual layers in the laminate exhibit different stress characteristics under pressure-assisted sintering.

42 ENGINEERING↗

On the preparation of TiAl alloy by direct reduction of the oxide mixtures in calcium chloride melt

In recent years, TiAl-based intermetallic alloys are being increasingly considered for application in areas such as (i) automobile/transport sector (passenger cars, trucks and ships) (ii) aerospace industry (jet engines and High Speed Civil Transport propulsion system) and (iii) industrial gas turbines. These materials offer excellent (i) high temperature properties (at higher than 6000C) (ii) mechanical strength and (iii) resistance to corrosion and as a result have raised renewed interest. The combination of these properties make them possible replacement materials for traditional nickel-based super-alloys, which are nearly as twice as dense (than TiAl based alloys). Since the microstructures of these intermetallic alloys affect, to a significant extent, their ultimate performance, further improvements (by way of alteration/modification of these microstructures), have been the subject matter of intense research investigations. It has now been established that the presence of alloy additives, such as niobium, tantalum, manganese, boron, chromium, silicon, nickel and yttrium etc, in specific quantities, impart marked improvement to the properties, viz. fatigue strength, fracture toughness, oxidation resistance and room temperature ductility, of these alloys. From a number of possible alloy compositions, {gamma}-TiAl and Ti-Al-Nb-Cr have, of late, emerged as two promising engineering alloys/materials. . The conventional fabrication process of these alloys include steps such as melting, forging and heat treatment/annealing of the alloy compositions. However, an electrochemical process offers an attractive proposition to prepare these alloys, directly from the mixture of the respective oxides, in just one step. The experimental approach, in this new process, was, therefore, to try to electrochemically reduce the (mixed) oxide pellet to an alloy phase. The removal of oxygen, from the (mixed) oxide pellet, was effected by polarizing the oxide pellet against a graphite electrode in a pool of molten calcium chloride at a temperature of 9000C. The dominant mechanism of the oxygen removal was the ionization of oxygen followed by its subsequent discharge, as CO2/CO, at the anode surface. The removal of oxygen from the oxide mixture helped form the alloy in situ. The presentation shall cover the detailed experimental results pertaining to the preparation, evaluation and characterization of Ti-47Al-2Nb-2Cr (atom%) alloy.

36 MATERIALS SCIENCE↗

EFFECT OF HUMIDITY LEVEL ON THE CREEP PROPERTIES OF ALLOY 903 AT 650 C

Alloy 903 (FeNiCo+Nb) is currently used for certain components in industrial gas turbines for low coefficient of thermal expansion applications. A variance in creep behavior for material quality control evaluations suggested a possible effect of moisture level on stress rupture properties. To investigate the role of water vapor on the creep properties of alloy 903, controlled laboratory experiments were conducted at 650 C with 0 to 100% relative humidity. The water content was controlled by flowing dry air through a water bath at a constant temperature. A significant decrease of lifetime was observed in the presence of water vapor, which is likely related to grain boundary embrittlement by the inward diffusion of hydrogen. The increase of the microstructure grain aspect ratio by different forging processes generally improved the rupture lifetime and elongation in air. However, all specimens had reduced lifetime in the presence of water vapor despite the microstructure grain aspect ratios.

08 HYDROGEN↗

Potential Experimental Topics for EGS Collab Experiment 3

To facilitate the success of FORGE, the DOE GTO has initiated a new research effort, the EGS Collab project, which will utilize readily accessible underground facilities that can refine our understanding of rock mass response to stimulation and provide a test bed at intermediate (~10 m) scale for the validation of thermal-hydrological-mechanical-chemical modeling approaches as well as novel monitoring tools. The first two EGS Experiments 1 and 2 are planned be performed under different stress/fracture conditions, and will evaluate different stimulation processes: Experiment 1 will focus on hydrofracturing of a competent rock mass, while Experiment 2 will concentrate on hydroshearing of a rock mass that contains natural fractures. Experiment 3 is scheduled to begin in 2019 will build off the lessons learned in Experiments 1 and 2 and will investigate alternate stimulation and operation methods to improve heat extraction in an EGS reservoir. This paper evaluates potential experiments that could potentially be conducted in Experiment 3. The two technical parameters defining energy extracted from EGS reservoirs with the highest economic uncertainty and risk are the production well flow rates and the reservoir thermal drawdown rate. A review of historical and currently on-going EGS studies has identified that over 1/2 of the projects have identified heat extraction challenges during their operation associated with these two parameters as well as some additional secondary issues. At present, no EGS reservoir has continuously produced flow rates on the order of 80 kg/s. Short circuiting (i.e. early thermal breakthrough) has been identified in numerous cases. In addition, working fluid loss (i.e. the difference between the injected fluid mass and the extracted fluid mass as compared to the injected mass) has been as high as 90%. Finally, the engineering aspects of operating a true EGS multi-fracture reservoir such as repairing/modifying fractures and controlling working fluid fluxes within multiple fractures for the effective EGS fracture management has not been sufficiently studied. To examine issues such as these, EGS Collab Experiment 3 may be conducted in the testbeds prepared for Experiments 1 and 2 by improving the previously performed stimulations, or conducted at a new site performing new stimulations with alternate method. Potential experiments may include using different stimulation and working fluids, evaluating different stimulation methods, using proppants to enhance permeability, and other high-risk high-reward methods that can be evaluated at the 10-m scale environment.

15 GEOTHERMAL ENERGY↗