Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A practical control strategy for demand flexibility with ensured occupant comfort in grid-interactive efficient buildings

This study proposes a practical and simplified demand response (DR) control strategy from the perspective of grid-interactive efficient buildings (GEBs), aiming to secure demand flexibility while ensuring occupant thermal comfort. Focusing on summer on-peak periods, a linear demand response (LDR) strategy that integrates cooling setpoint adjustment and lighting dimming was designed, and its performance was quantitatively evaluated. A case study was conducted using EnergyPlus-based simulations for a U.S. DOE small office prototype building under summer on-peak weather conditions. Compared with a conventional rapid demand response (RDR) strategy, the proposed LDR approach gradually reduced electrical loads while maintaining occupant thermal comfort indices, including predicted mean vote (PMV) and predicted percentage of dissatisfied (PPD), within acceptable comfort ranges. Quantitative analysis of demand flexibility using the grid-interactive impact index (GII) and the flexibility strength index (FSI) showed that the LDR strategy provided approximately 12.5% demand flexibility during DR periods and achieved an electricity cost reduction of about 8.8%. In addition, the results of the part-load ratio (PLR)-based cooling system performance analysis showed that, in the on-peak period, the LDR strategy exhibited improved cooling performance compared with the baseline. Overall, this study shows the potential of a practical DR control strategy that can simultaneously achieve occupant comfort and demand flexibility without relying on complex advanced control technologies.

Jung, Dong Eun↗
DOE OSTI2021

Fourier-like Thermal Relaxation of Nanoscale Explosive Hot Spots

Hot spots are local regions of high temperature that are widely considered to govern explosive initiation. Hot spot dynamics rests on a delicate balance between heat generation due to chemical reactions and heat loss through thermal conduction, making accurate determinations of the conductivity under extreme conditions a key component of predictive explosive models. We develop here an approach to directly determine the thermal transport properties of explosive hot spots with realistic initial structures through a combination of molecular dynamics (MD) and diffusive heat equation (HEq) modeling. Effective thermal conductivity values are determined by fitting HEq models to MD predictions of long timescale hot spot relaxation. The approach is applied to model hot spots in the molecular crystalline explosive 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) for a range of shock strengths and two limiting cases for impact orientation. Isotropic and anisotropic HEq models yield similar results, despite TATB exhibiting some of the largest and most anisotropic thermal conductivity values for explosive near normal conditions. The conductivity is found to be a strong function of density, which parametrically captures dependence on temperature, pressure, and material state. The associated root-mean-square errors of the fitted HEq models are approximately 5% of MD predicted final equilibrium temperatures. Here, the conductivity values determined here for TATB hot spots are considerably larger than those used in a prior hot spot criticality study, which may significantly impact predictions for critical hot spot sizes. The approach provides a convenient foundation for determining the effective thermal conductivity for hot spot problems in other explosives and directly yields information on reasonable approximations that might be taken in higher-level models for those materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Modifying Interface Solvation and Oxygen Reduction Electrocatalysis with Hydrophobic Species

Ionic liquid interlayers improve the oxygen reduction reaction (ORR) kinetics on bulk and nanostructured catalysts for both Pt and alloyed-Pt materials. Despite the demonstrated performance enhancement at the half-cell and membrane electrode assembly level, the mechanism of the improvement is not fully understood. In this work, we combine single-crystal experiments with microkinetic modeling to uncover the origin of the ORR kinetic improvement on Pt(111) in the presence of ionic liquids and hydrophobic cations. With the incorporation of a modified Frumkin isotherm, our model accurately simulates the disorder–order transition observed in hydroxyl and bisulfate adsorption on Pt(111) under acidic conditions. Voltametric analysis shows that ionic liquids impact solvation to break so-called scaling relations between the adsorption strength of OH ad and O ad , but these effects have little impact on ORR activity. Instead, destabilized OH ad reduces the overall hydroxyl (spectator) coverage, resulting in higher availability of active sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The impact of the electric field of metal ions on the vibrations and internal hydrogen bond strength in alkali metal ion di- and triglycine complexes

Using infrared predissociation spectroscopy of cryogenic ions, we revisit the vibrational spectra of alkali metal ion (Li+, Na+, K+) di- and triglycine complexes. We assign their most stable conformation, which involves metal ion coordination to all C=O groups and an internal NH⋯NH2 hydrogen bond in the peptide backbone. An analysis of the spectral shifts of the OH and C=O stretching vibrations across the different metal ions and peptide chain lengths shows that these are largely caused by the electric field of the metal ion, which varies in strength as a function of the square of the distance. The metal ion–peptide interaction also remotely modulates the strength of internal hydrogen bonding in the peptide backbone via the weakening of the amide C=O bond, resulting in a decrease in internal hydrogen bond strength from Li+ > Na+ > K+.

Chemistry↗
DOE OSTI2024

Utilizing integrated neutron diffraction and elastoplastic self-consistent crystal plasticity model to quantitatively assess the strengthening mechanism in Al–12.5Ce and Al–12.5Ce–0.4Mg alloys

An integrated in-situ neutron diffraction and elastic plastic self-consistent crystal plasticity (EPSC-CP) modeling scheme is performed on a binary Al–12Ce alloy and a ternary Al–12Ce–0.4Mg alloys. Using this scheme, the constitutive parameters, i.e. elastic constants and slip system parameters of individual phases can be calibrated which can be used in microstructure-based CP models to predict materials performance. From this study, it is shown that the elastic constants of Al 11 Ce 3 intermetallics calculated from density function theory calculation in the literature are rather accurate. When applied to the EPSC-CP model, the lattice strains of both the binary and ternary alloys are correctly predicted as compared with experiments, and large lattice strain differences between Al (100) plane and Al 11 Ce 3 (010) plane are demonstrated. The slip system parameters calibrated by the scheme shows that the addition of 0.4 wt% Mg in the alloy has little influence on the critical resolved shear stress of initial dislocation glide in the Al matrix which caused plastic yield in the material. This can be explained by the very dilute Mg solute content in the Al solid solution, causing large spacing of Al–Mg lattice misfit sites and little impact on resistance of dislocation glide at initial yield. The 0.4 wt% Mg addition, on the other hand, has a large influence on the hardening term in the slip system parameters, indicating those Al–Mg misfit sites do help dislocation accumulation during the deformation. The impact of dilute Mg addition on the Al slip system parameters is also reflected in the flow behavior of the ternary alloy: little impact on the yield stress, but a large impact on working hardening and tensile strength of the materials which is consistent with the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The road to atomically thin metasurface optics

Abstract The development of flat optics has taken the world by storm. The initial mission was to try and replace conventional optical elements by thinner, lightweight equivalents. However, while developing this technology and learning about its strengths and limitations, researchers have identified a myriad of exciting new opportunities. It is therefore a great moment to explore where flat optics can really make a difference and what materials and building blocks are needed to make further progress. Building on its strengths, flat optics is bound to impact computational imaging, active wavefront manipulation, ultrafast spatiotemporal control of light, quantum communications, thermal emission management, novel display technologies, and sensing. In parallel with the development of flat optics, we have witnessed an incredible progress in the large-area synthesis and physical understanding of atomically thin, two-dimensional (2D) quantum materials. Given that these materials bring a wealth of unique physical properties and feature the same dimensionality as planar optical elements, they appear to have exactly what it takes to develop the next generation of high-performance flat optics.

Brongersma, Mark L.↗
DOE OSTI2017

Assessing Occupant and Outdoor Air Impacts on Indoor Air Quality in New California Homes

In 2008 the State of California adopted new building codes that required the use of mechanical ventilation systems in homes that meet the requirements of ASHRAE Standard 62.2. The standard requires both a dwelling unit mechanical ventilation system and exhaust fans in kitchens and bathrooms. A field study was undertaken to evaluate the IAQ and ventilation performance of homes built to these requirements. For ventilation system performance, the airflows of all mechanical ventilation systems were measured and their use was monitored for a one-week period. To evaluate IAQ, key pollutants were measured indoors and outdoors during the week, and occupants completed satisfaction surveys. The key pollutants included: formaldehyde, humidity, PM2.5 and NO2. Passive samplers were used to determine average concentrations for the week. Active samplers were used to develop time-series results that can be used to correlate pollutant concentrations with occupant activities. Other ventilation/IAQ related parameters were also recorded, such as stove top temperatures to indicate cooking, exterior door contact switches to know when large openings were being used for ventilation and sensors to determine when clothes dryers were being used. The building envelope and duct leakage were measured to enable estimates of infiltration and duct leakage effects. This paper presents an overview of the test procedures and preliminary results from several homes. The results show that although average concentrations may be reasonable compared to available standards (with the exception of formaldehyde), occupants have a strong impact on pollutant variability and source strength and that outdoor concentrations cannot be ignored. Overall, these mechanically ventilated homes have reasonable IAQ. The homes and duct systems are moderately tight, though not excessively so, by US standards. Significant concerns have been expressed regarding compliance with the ventilation requirements in the California building code. However, almost all the ventilation systems in this study complied with the ventilation air flow requirements and on average were significantly higher than the minimum required air flow rates.

Walker, IS↗
DOE OSTI2023

Modeling Solids in Nuclear Astrophysics with Smoothed Particle Hydrodynamics

Abstract Smoothed particle hydrodynamics (SPH) is a frequently applied tool in computational astrophysics to solve the fluid dynamics equations governing the systems under study. For some problems, for example when involving asteroids and asteroid impacts, the additional inclusion of material strength is necessary in order to accurately describe the dynamics. In compact stars, that is white dwarfs and neutron stars, solid components are also present. Neutron stars have a solid crust, which is the strongest material known in nature. However, their dynamical evolution, when modeled via SPH or other computational fluid dynamics codes, is usually described as a purely fluid dynamics problem. Here, we present the first 3D simulations of neutron star crustal toroidal oscillations including material strength with the Los Alamos National Laboratory SPH code FleCSPH. In the first half of the paper, we present the numerical implementation of solid material modeling together with standard tests. The second half is on the simulation of crustal oscillations in the fundamental toroidal mode. Here, we dedicate a large fraction of the paper to approaches that can suppress numerical noise in the solid. If not minimized, the latter can dominate the crustal motion in the simulations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1976

Advances in engineering science, volume 1

Proceedings from a conference on engineering advances are presented, including materials science, fracture mechanics, and impact and vibration testing. The tensile strength and moisture transport of laminates are also discussed.

Source record↗
NASA NTRS1992

Atomic data and spectral analysis of carbon, nitrogen, oxygen and silicon ions observed with the International Ultraviolet Explorer

According to the plan presented in the original proposal we have now completed most of the atomic calculations involving collision strengths and rate coefficients for electron impact excitation of C II, N III, and O IV ions. These have been reported in the first two publications appended with this report. We have now moved into the applications phase of the project with the new data being used to analyze the International Ultraviolet Explorer (IUE) observations of a variety of objects, as described in the third publication recently submitted (also appended). The analysis and interpretation of archival data will continue well into the next year with several collaborators that the PI and Co-PI are involved with. In addition, the atomic calculations on Si II have been started.

Pradhan, Anil K.↗
NASA NTRS1993

Low and high velocity impact response of thick hybrid composites

The effects of low and high velocity impact on thick hybrid composites (THC's) were experimentally compared. Test Beams consisted of CFRP skins which were bonded onto an interleaved syntactic foam core and cured at 177 C (350 F). The impactor tip for both cases was a 16 mm (0.625 inch) steel hemisphere. In spite of the order of magnitude difference in velocity ranges and impactor weights, similar relationships between impact energy, damage size, and residual strength were found. The dependence of the skin compressive strength on damage size agree well with analytical open hole models for composite laminates and may enable the prediction of ultimate performance for the damaged composite, based on visual inspection.

Hiel, Clement↗
NASA NTRS2002

Foreign Object Damage Behavior of Two Gas-turbine Grade Silicon Nitrides by Steel Ball Projectiles at Ambient Temperature

Foreign object damage (FOD) behavior of two commercial gas-turbine grade silicon nitrides, AS800 and SN282, was determined at ambient temperature through strength testing of flexure test specimens impacted by steel-ball projectiles with a diameter of 1.59 mm in a velocity range from 220 to 440 m/s. AS800 silicon nitride exhibited a greater FOD resistance than SN282, primarily due to its greater value of fracture toughness (K(sub IC)). Additionally, the FOD response of an equiaxed, fine-grained silicon nitride (NC132) was also investigated to provide further insight. The NC132 silicon nitride exhibited the lowest fracture toughness of the three materials tested, providing further evidence that K(sub IC) is a key material parameter affecting FOD resistance. The observed damage generated by projectile impact was typically in the forms of well- or ill-developed ring or cone cracks with little presence of radial cracks.

Choi, Sung R.↗
NASA NTRS2004

Foreign Object Damage in Flexure Bars of Two Gas-Turbine Grade Silicon Nitrides

Foreign object damage (FOD) behavior of two commercial gas-turbine grade silicon nitrides, AS800 and SN282, was determined at ambient temperature through strength testing of flexure test specimens impacted by steel ball projectiles with a diameter of 1.59 mm in a velocity range from 220 to 440 m/s. AS800 silicon nitride exhibited a greater FOD resistance than SN282, primarily due to its greater value of fracture toughness (K(sub lc)). The use of an additional equiaxed, fine-grained silicon nitride (NC132) showed that fracture toughness was a key material parameter affecting FOD resistance. The observed damages generated by projectile impact were typically in the forms of well- or ill-developed ring and cone cracks with little presence of radial cracks.

Choi, Sung R.↗
NASA NTRS2012

Meridional Flow in Solar Cycle 24: The Impact on the Polar Magnetic Fields

Axisymmetric flows, Differential Rotation and Meridional Flow (MF), were measured by tracking the motion of magnetic elements on the surface of the Sun using data obtained by the Helioseismic and Magnetic Imager (HMI) on the NASA Solar Dynamics Observatory (SDO) Mission. HMI provides the highest resolution full ]disk magnetograms available to date. This dramatically reduces the noise in axisymmetric flows, particularly at high latitudes (i.e. near the poles). The MF was found to vary greatly from one Carrington Rotation to the next. Furthermore, a distinct north ]south difference was found in the MF at high latitudes: Flow in the South was persistently weaker than flow in the North. Conclusions will be drawn concerning the MF variability, north ]south differences, and the impact on the polar magnetic field strengths and the timing of their reversals.

Upton, Lisa↗
NASA NTRS2018

Sandwich Structure Risk Reduction in Support of the Payload Adapter Fitting

Reducing risk for utilizing honeycomb sandwich structure for the Space Launch System payload adapter fitting includes determining what parameters need to be tested for damage tolerance to ensure a safe structure. Specimen size and boundary conditions are the most practical parameters to use in damage tolerance inspection. The effect of impact over core splices and foreign object debris between the facesheet and core is assessed. Effects of enhanced damage tolerance by applying an outer layer of carbon fiber woven cloth is examined. A simple repair technique for barely visible impact damage that restores all compression strength is presented.

Nettles, A. T.↗
NASA NTRS2018

A Critical Review of the Measurement of Ice Adhesion to Solid Substrates

Ice adhesion is an issue spanning a wide range of technical fields. In the aerospace industry, ice accretion has led to a large number of casualties and costs the industry billions of dollars every year. To design effective anti-/de-icing systems, the adhesion of ice to surfaces must be understood. In this review paper, the authors surveyed for papers providing methods for the measurement of ice adhesion. 113 papers were identified for comparison, with data being extracted from 58 papers with common test surfaces (aluminum, steel, Teflon® (Chemours), and polyurethane). The methods used were categorized and data were compared based on their precision and the trends they demonstrated. Conceptual problems were identified with the tests used in the literature and discussed, and open questions relevant to testing the adhesion of ice were identified. Several key parameters affecting ice adhesion identified from the literature were temperature, surface roughness, strain rate, and impact velocity. Their effects on adhesion strength were discussed. While researching this topic, it was discovered that many papers did not report the strain rate in their tests, and the vast majority of papers did not correct their data for stress concentrations on the surface, either of which has been shown to cause variation in the data by one order of magnitude. Data compared from the literature typically spanned one to three orders of magnitude. The causes of these variations were discussed.

Andrew H. Work↗
NASA NTRSDate not supplied

TPSAS-NF1676L-25778-DND

Testing required to design and certify aircraft structures has increased dramatically with the growth in use of composite materials, and the development time and cost have become an issue as industry looks towards the next generation of aircraft. To help address this challenge, NASA has formed an industry-spanning consortium with the goal of cutting by 30% today's 10-year timeline for developing and certifying composite aircraft structures. This goal is to be achieved by infusing leading edge, physics-based tools to improve the prediction of the response and failure of composite aerospace structures. The plan for the public-private partnership of NASA, the FAA, airframe manufacturers, aircraft engine manufacturers, and several universities is to conduct joint research under the five-year Advanced Composites Program (ACP). The emphasis of the ACP project is the development of damage prediction and non-destructive inspection methods capabilities that are sufficiently reliable to enable a reduction in the element and subcomponent testing necessary for design and certification. ACP also is expected to create rapid design tools to speed preliminary design and improve safety and performance. A critical element of this research concerns the residual strength of postbuckled stiffened panels with impact damage. This presentation will discuss different aspects of ongoing research on the prediction of structural collapse due to skin/stiffener separation. In particular, the presentation will examine issues that must be addressed in the analysis, such as R-curve toughening, delamination migration, bridging, as well as some unexpected effects of ply orientation.

Carlos G Davila↗