Search NASA⌕ Search

SEARCH · Search NASA

Results for “Implementation Plan”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Annual Report of Monitoring at Barnes, Kansas, in 2016

In 2006, the CCC/USDA assumed responsibility for the site investigation relating to potential carbon tetrachloride contamination. Initially, the CCC/USDA developed and implemented a work plan for targeted groundwater sampling and monitoring well installation (KDHE 2009). The investigation and subsequent monitoring (Argonne 2008a-d, 2009a,b, 2010, 2011, 2012, 2013, 2015a,b, 2016) were performed by the Environmental Science Division of Argonne National Laboratory. The reports of environmental investigations at Barnes are summarized.

54 ENVIRONMENTAL SCIENCES↗

Report of the Sixth Regional Review Meeting of the Radiological Security Partnership.

The Sri Lanka Atomic Energy Regulatory Commission (AERC) and the United States Department of Energy (U.S. DOE) co-hosted the 6th Regional Review Meeting on Radiological Security involving representatives from over 20 countries, the International Atomic Energy Agency (IAEA), the International Criminal Police Organization (INTERPOL), and the World Institute for Nuclear Security. The purpose of the event was to discuss the implementation of, and plans for, high-activity radioactive source security (RSS). The U.S. DOE’s National Nuclear Security Administration (NNSA) Office of Radiological Security (ORS) fully sponsored this review meeting. Participants were welcomed to Colombo, Sri Lanka, and the meeting was formally opened by Nirmali Karunarathna of the Sri Lanka Atomic Energy Regulator Council who emphasized the strong partnerships among the participants. The opening Ceremony and Lamp Lighting included dignitaries from the sponsoring countries. Robert Hilton, Deputy Chief of Mission at the U.S. Embassy in Colombo, and Kristin Hirsch of the ORS gave other opening remarks that highlighted the social benefit from radiological sources in medicine, industry, and agriculture, while stressing the importance of addressing the risks associated with the malicious use of radiological sources. Emphasis was placed on the importance of partnerships among all the participants to help ensure the success of securing radiological materials throughout the world and the opportunity to share information and experiences. AERC was acknowledged with special thanks for hosting this event. A participant list is included as Attachment A, and the meeting agenda is provided as Attachment B. All presentations were made available to participants. The following sections summarize the meeting’s presentations, discussions, issues, suggestions, and recommendations.

61 RADIATION PROTECTION AND DOSIMETRY↗

Development of NDE/NDT Tools for High-Volume & High-Speed Inspection of CFRP Structures in Automotive Manufacturing

Main advantages of the air-coupled ultrasound testing (ACUT) and electromagnetic testing (EMT) techniques for NDE of CFRP composites were non-contact sensing, scalability for high-speed inspection, cost-effectiveness, and non-hazardous operation. Despite these advantages, no systems that would satisfy the project requirements were commercially available. Hence, one of the major efforts of the Michigan State University (MSU) team at the initial stage of the project was to close this technological gap by developing, optimizing, and validating array sensors that would provide sufficient sensitivity, spatial coverage, and resolution for robust defect detection. Optimization of the ACUT and EMT sensor designs was performed using experimentally validated finite element models. Initial experiments using array probes were conducted on relatively flat CFRP samples. In parallel, the MSU team designed and assembled a portable platform with two robotic arms. The robots were equipped with newly designed sensors that enabled high-speed NDE of curved CFRP parts. Presently, the developed robotic platform can be used as a demo/template NDE system, which is easily adaptable to manufacturing environments and in-line NDE. The ACUT NDE system developed by the MSU team used a high-power 4-channel pulser receiver for parallel data acquisition. The array probes were designed by stacking commercially available ACUT transducers, which operated in the frequency range between 100 kHz and 500 kHz. MSU optimized the excitation procedure and developed wave focusing cones so as to reduce the crosstalk between the transducers and to provide higher pulse repletion frequency (PRF). The through-transmission (TT) and single-side access (SSA) inspection modes were successfully implemented. In the TT-ACUT, structural defects in CFRP were detected by passing ultrasonic waves through the test part. Hence, the ACUT transmitters and receivers needed to be placed on the opposite sides of the test part. In the SSA-ACUT, guided waves (GW) were excited in the test part using the transmitters and were sensed by the receivers from the same side. Multi-channel TT-ACUT and SSA-ACUT provided high-speed NDE, and were successfully validated on CFRP test samples with interlaminar delaminations and other embedded defects The EM techniques developed by the MSU team included: 1) eddy current testing (ECT), 2) capacitive imaging (CI) and hybrid dual-mode imaging. In ECT, structural damage was detected in CFRP using coils sensor arrays. In ECT, the excitation magnetic field is generated by passing an alternating current through a coil, which is placed above the test sample. The excitation field penetrates the conductive sample and induces the eddy currents in its transect. In turn, the eddy currents generate the reaction field, which affects the total field sensed by a coil. Hence, the presence of structural flaws will alter the eddy current flow and the picked-up signal. ECT is mostly sensitive to local changes of the electric conductivity of the test sample, and CFRPs are mostly conductive in the direction of carbon fibers. Hence, ECT was well suited for the detection of fiber damage/fiber irregularities. The MSU team developed printed circuit boards (PCB) with coil sensor arrays optimized for NDE of CFRP. Unlike most commercial probes designed for ECT of metallic structures, the MSU array probes were designed for operation in [1-10] MHz frequency range, which was optimal for low-conductive CFRP. Multiple sensing topologies (coil groups excitation/sensing arrangements) were implemented and successfully validated. Capacitive Imaging (CI) technique developed by MSU was complementary to ECT. In contrast to ECT, which was sensitive to local changes of the electrical conductivity, the CI was sensitive to local changes of the dielectric constant. Therefore, CI could provide information about matrix damage/matrix irregularities in CFRP. The MSU CI sensor arrays were made of multiple circular or rectangular open-plate capacitors printed on PCB. Sensors of this type are not commercially available. In addition to ECT and CI, the MSU team developed a hybrid (dual-mode) inductive/capacitive measurement technique that synergistically combined the benefits of inductive and capacitive sensing for rapid NDE of fiber reinforced polymer (FRP) composite structures. Fiber damage and fiber irregularities in FRPs were detected by configuring hybrid sensors as coil sensors. Similarly, matrix damage, matrix irregularities and interlaminar delaminations were detected by configuring hybrid sensors as capacitive sensors. ECT and CI were performed sequentially by means of electronic switching. Hence, eliminating the need for mounting two separate sensor arrays on the probe. Portable robotic platform was developed by MSU for multi-technique high-speed NDE of CFRP test parts. The platform had two 6-axis robots, which enabled inspection of curved parts in approximately a 6×6×6 ft 3 active scan area. On the software side, the MSU team integrated scripts for NDE hardware control with scripts for robot motion control. MSU also implemented automated path planning for the robots, reconstruction of part’s surfaces via stereovision, 3D rendering of inspection data, and image processing algorithms for enhanced defect detection. Automotive composite parts manufactured by Plasan Composites from Phase I were used to validate the ACUT and EMT techniques on representative testbeds. Among those parts were three X-braces for a Dodge Viper, one composite calibration plaque with known defects at known locations, and four other test sections, including sections from a front splitter, a corner section from a composite hood, and a high-pressure RTM panel made using non crimp fabric. Other test samples included CFRP and GFRP calibration plates with fiber/matrix defects fabricated at MSU/CVRC.

36 MATERIALS SCIENCE↗

Well-Controlled Hydro-thermo-chemical Stimulation of a Coso Geothermal Well to Enhance Productivity

The goal of this project was to demonstrate controlled fracturing and permeability increase to enhance resource production and power generation at Coso. It was planned to stimulate at least two intervals in the Well 73-18RD with zonal isolation using advanced high-temperature packer technology. The anticipation was that a hydraulic fracture would form in one zone and in the second zone natural fractures would reopen, shear and extend, thereby increasing fluid communication in the field. In both cases, the intent was to carefully design the stimulation to take advantage of the relative roles of hydraulic pressure, thermal stress and chemical (“hydro-thermo-chemical”) dissolution. The project had planned to use the Welltec Annular Barrier (WAB) system developed as part of another DOE-funded project which was on schedule to be ready for field deployment. If successful, the Coso Operating Company would incorporate this approach into their ongoing well maintenance in other wells increasing the total MWs produced. The project had multiple tasks and the objective of Task 1 was to develop a workover plan, to build a geologic model, to design a stimulation program, and to work with the operating and services companies to develop a detailed budget and obtain the necessary permits and sundry notices. In Phase 2 the workover plan would be implemented, the designed stimulation would be carried out, and subsequently the well would logged and tested to measure the impact of stimulation. Per sponsor request, a Pre-Task 1 activity with a Go/No Go decision point was scheduled in Task 1.

02 PETROLEUM↗

Accelerating Informed Local Climate Action by Improving Access to DOE Predictive Modeling and Science-Based Tools

The threat of climate change is becoming increasingly urgent, and local governments across the United States are working to develop and implement climate action plans to reduce greenhouse gas emissions and mitigate the impacts of climate change. At the same time, the U.S. Department of Energy's Office of Science, Earth and Environmental Systems Sciences Division (EESSD) has been developing a range of tools and technologies to help predict the potential multi-faceted impacts from climate change given varying environmental and socioeconomic scenarios. However, local governments have been slow to engage with these scientific assets due to a lack of understanding and awareness. The DOE researchers interviewed highlighted three primary types of resources that could benefit local governments and climate practitioners: climate models, modeled datasets, and scientific journal articles. Although many of these resources are open source and available to the public, there were several challenges identified in translating these resources and their research insights directly to decision-makers.

54 ENVIRONMENTAL SCIENCES↗

Feasibility and Qualitative Risk Assessment of Fuel Cell Electric Bus Use for Emergency Backup Power for Airport Applications

Airports rely on robust backup power systems to maintain critical operations during emergencies. This paper investigates the feasibility of using hydrogen fuel cell electric buses (FCEBs) as emergency backup power sources, focusing on their technical specifications, operational challenges, and associated risks. Using Portland International Airport as a case study, the analysis evaluates the power output and hydrogen consumption of New Flyer’s 40’ Xcelsior Charge fuel cell buses, to provide power for key airport systems. Additionally, the paper explores the design and layout of how FCEBs can be connected to airport facilities, and addresses safety considerations, hydrogen supply logistics, and electrical compatibility. While FCEBs present significant advantages in terms of sustainability and resilience, their implementation requires careful planning, infrastructure investment, and adherence to safety standards. This research provides actionable insights for airport stakeholders seeking to transition to hydrogen-based backup power system.

08 HYDROGEN↗

Cyber-Informed Engineering for Strategic Planning

The CIE Guide for Engaging Organizational Leadership: Board and C-Suite describes how to apply CIE at the senior-level of organizational management. This guidance integrates CIE concepts into theory and practice of guiding coalition leadership to improve permeation of CIE concepts throughout organizational culture. This guide incorporates feedback from CIE community of practice volunteers in a study of how business administrative and strategic planning and management guidance and course materials can be applied to CIE implementation throughout an organization's principles and processes. This guide defines the interests guiding senior leadership, managers and supervisors, and technicians and workers involved in creating and operating and maintaining systems, and cultural/ historical/ political assumptions or influences shaped the landscape that could facilitate or impede development of CIE. The included guidance for organizational strategic management and leadership can be imbedded into contract guidance based on the CIE implementation guide and lessons learned from industry application.

97 MATHEMATICS AND COMPUTING↗

WSF Biodiesel Demonstration Project Final Report

In 2004, WSF canceled a biodiesel fuel test because of “product quality issues” that caused the fuel purifiers to clog. The cancelation of this test and the poor results negatively impacted the use of biodiesel in marine application in the Pacific Northwest. In 2006, The U.S. Department of Energy awarded the Puget Sound Clean Air Agency a grant to manage a scientific study investigating appropriate fuel specifications for biodiesel, fuel handling procedures and to conduct a fuel test using biodiesel fuels in WSF operations. The Agency put together a project team comprised of experts in fields of biodiesel research and analysis, biodiesel production, marine engineering and WSF personnel. The team reviewed biodiesel technical papers, reviewed the 2004 fuel test results, designed a fuel test plan and provided technical assistance during the test. The research reviewed the available information on the 2004 fuel test and conducted mock laboratory experiments, but was not able to determine why the fuel filters clogged. The team then conducted a literature review and designed a fuel test plan. The team implemented a controlled introduction of biodiesel fuels to the test vessels while monitoring the environmental conditions on the vessels and checking fuel quality throughout the fuel distribution system. The fuel test was conducted on the same three vessels that participated in the canceled 2004 test using the same ferry routes. Each vessel used biodiesel produced from a different feedstock (i.e. soy, canola and yellow grease). The vessels all ran on ultra low sulfur diesel blended with biodiesel. The percentage of biodiesel was incrementally raised form from 5 to 20 percent. Once the vessels reached the 20 percent level, they continued at this blend ratio for the remainder of the test. Fuel samples were taken from the fuel manufacturer, during fueling operations and at several points onboard each vessel. WSF Engineers monitored the performance of the fuel systems and engines. Each test vessel did experience a microbial growth bloom that produced a build up of material in the fuel purifiers similar to material witnessed in the 2004 fuel test. A biocide was added with each fuel shipment and the problem subsided. In January of 2009, the WSF successfully completed an eleven month biodiesel fuel test using approximately 1,395,000 gallons of biodiesel blended fuels. The project demonstrated that biodiesel can be used successfully in marine vessels and that current ASTM specifications are satisfactory for marine vessels. Microbial growth in biodiesel diesel interface should be monitored. An inspection of the engines showed no signs of being negatively impacted by the test.

09 BIOMASS FUELS↗

QM02 Strength Measurement

In late April, Paul Emma reported that his orbit fitting program could find a reasonably good fit only if the strength of QM02 was changed from design value of -5.83 kG to -6.25 kG - a strength change of 7.3%. In late May, we made a focal length measurement of QM02 by turning off all focusing optics between YC07 and BPMS1 (in the spectrometer line) except for QM02 and adjusted the strength of QM02 so that vertical kicks by YC07 did not produce any displacements at BPMS1 (see Figure 1). The result was quoted in the LCLS elog was that QM02 appeared to 6% too weak, and approximately agreed with Paul's observation. The analysis used for the entry in the log book was based on the thin lens approximation and used the following numbers: Distance YC07 to QM02 - 5.128 m; Distance QM02 to BPMS1 - 1.778 m; and Energy - 135 MeV. These distances were computed from the X,Z coordinates given the on the large plot of the Injector on the wall of the control room. On review of the MAD output file coordinates, it seems that the distance used for QM02 to BPMS1 is not 1.778 m. The correct value is Distance, center of QM02 to BPMS1 - 1.845 m. There may be a typo on the wall chart values for the coordinates of BPMS1, or perhaps there was a misinterpretation of edge versus center of QM02. In any case, the effect of this change is that the thin lens estimate changes from 6% too weak to 9% too weak. At John Galayda's suggestion, we looked into the thin lens versus thick lens approximation. A Mathematica program was written to solve for the K value of the QM02, in the thick lens approximation, that provides point to point focusing from YC07 to BPMS1, and to compare this number with the value obtained using the thin lens approximation. The length of QM02 used in the thick lens calculation is the effective length determined by magnetic measurements of 0.108 m. The result of the Mathematica calculation is that the thin lens approximation predicts less magnet strength is required to produce the same focusing by about 1.3%. When both the distance correction and the thick lens approximation are taken into account, the result is: K{sub thick} - K{sub mm}/K{sub thick} = -7.6% where K{sub mm} is the value obtained from magnetic measurements and K{sub thick} is the value of K obtained from the focal length measurement in the thick lens approximation. That is, QM02 acts weaker than it was measured by magnetic measurements by 7.6%. This is remarkably close to Paul's original estimate. The unexpected weakness could in principle be due to several things: shorted turns, a current calibration error, magnetic measurement error; it could even be due to the presence of an gradient from QM01, which is of opposite sign and right next to QM02, despite it being set to zero current (although it was not DAC-zeroed). Plans have been implemented to remove and replace QM02 at the earliest ROD.

43 PARTICLE ACCELERATORS↗

MC&A System Effectiveness Tool (MSET) (Presentation 2)

MSET is a self-assessment or inspection tool utilizing probabilistic risk assessment (PRA) methodology to calculate the system effectiveness of a nuclear facility's material control and accountability (MC&A) system. MSET analyzes the effectiveness of an MC&A system based on defined performance metrics for MC&A functions defined based on U.S. and international best practices and regulations. MSET analysis is based on performance of the entire MC&A system including defense-in-depth attributes and sensitivity analysis of changes in the system, both positive and negative. MSET analysis considers: accounting; containment; access control; surveillance capabilities of the system; and other interfaces with the physical protection systems that provide detection of an unauthorized action. MSET performs a system effectiveness calculation evaluation against a defined performance metric. MSET uses PRA techniques to analyze the MC&A system. MSET is a tool for evaluating the system effectiveness of MC&A systems during self-assessment or external inspection. MSET has been developed, tested, and benchmarked by the U.S. DOE. In collaboration with the U.S. DOE, Rosatom is developing a Russian version (MSET-R) planned for pilot implementation at select material balance areas in 2011. MSET has been shown to be an effective training and communication tool for MC&A.

99 GENERAL AND MISCELLANEOUS↗

Neutrinos from Stored Muons (nuSTORM)

The 2020 Update of the European Strategy for Particle Physics (ESPP) (see https://cds.cern.ch/record/2720129 ) recommended that muon beam R&D should be considered a high-priority future initiative and that a programme of experimentation be developed to determine the neutrino cross-sections required to extract the most physics from the DUNE and Hyper-K long-baseline experiments. The ENUBET and nuSTORM collaborations have begun to work within and alongside the CERN Physics Beyond Colliders study group and the international Muon Collider collaboration to carry out a joint, five-year R&D programme to deliver a detailed plan for the implementation of an infrastructure in which: (1) ENUBET and nuSTORM deliver the neutrino cross-section measurement programme identified in the ESPP and allow sensitive searches for physics beyond the Standard Model to be carried out; and in which (2) A 6D muon ionisation cooling experiment is delivered as part of the technology development programme defined by the international Muon Collider collaboration. This document summarises the status of development of the nuSTORM and 6D cooling experiments and identifies opportunities for collaboration in the development of the initiative outlined above.

43 PARTICLE ACCELERATORS↗

Remote-Controlled Removal of Bricks from a Reactor Shaft: An Unconventional Approach - 16406

The first German prototype Fast Breeder Nuclear Reactor (KNK) is currently being dismantled after being the only operating Fast Breeder-type reactor in Germany. The complete dismantling is based on 10 decommissioning permits. Package 3 of the 9. decommissioning permit, which is currently under preparation, comprises the dismantling of the biological shield. Package 2 comprised the dismantling of the Primary Shield. In preparation to lift the 14 primary shield segments on height of the reactor core, these were milled at 16 positions and equipped with a total of 26 holes. As a result of the milling and drilling process, an estimated amount of 500-600 kg cast iron swarfs accumulated at the bottom of the 12 m deep reactor shaft. The cobalt in the cast iron was activated to cobalt-60 during operation. This results in a measurable dose-rate of 30-35 mSv/h. At the conical bottom of the reactor shaft were still the remaining parts of the thermal insulation consisting of a lining with brick stones, covered with loose remnants of the thermal insulation, loose metallic residues and cut-off wheels of the angel grinder. For the next dismantling step, the removal of the activated part of the biological shield, it is necessary that the cast iron swarfs must be removed as well as the remains of the thermal insulation. Firstly, this is necessary to reduce the dose rate inside the shaft for subsequent breakthrough operations and, secondly to have a statically resilient surface for the installation of a necessary working platform for next dismantling tools. There was no access for personnel. A manual removal was also not possible due to the existing dose rate. The cast iron swarfs supposed to be removed by a remote controlled suction unit, which was installed on top of a drum and mounted in a special rack. The complete system was lowered into the reactor shaft by using a crane. After removing the major amount of swarfs, the remaining swarfs as well as the sheet metal liner should be collected with a magnetic grabber. The solution for the metal removal was easy to realize, but there was no idea how to remove the remaining bricks remote controlled out of the reactor shaft. Another boundary was that only existing facilities were supposed to be used in addition to the new suction system, i.e. the existing cranes, gripper, as well as the double lid lock of the encasing for the handling of the vacuum cleaner, the transport of the drum and the lock procedure. The design essentially consists of a suction unit and a collecting unit. Both units are connected hooked by the three single suspension chains on the rack on the traverse and connection of the suction tube. Subsequently the entire unit was drained in the 12 m deep reactor shaft. The entire unit has been lifted out of the reactor shaft and placed on a defined set-down position. At this position, now both of the units could be separated by using the Master-Slave-Manipulator in the encasing (A100). By using different suction pipes the reactor shaft bottom could be exempted from the cast iron swarfs within a few days. The suction unit worked in such a positive way that it was decided to remove the loose refractory bricks, metallic residues, cut off wheels, etc., too. Metal parts remaining on the ground were removed by a magnet. This pragmatic approach avoided additional complex design works and the need of constructing special solutions and thus, massively saved time, cost and dose rate. The duration of planning, permission including implementation amounted to approximately 3 to 4 months. The additional work could be performed directly after the actual dismantling step.

07 ISOTOPE AND RADIATION SOURCES↗

Future German R and D on HLW Disposal - 16519

In 2009, after the General elections, the new German Government showed a relatively positive attitude towards a prolonged use of nuclear power. Power plant shutdown was planned for the year 2032. Nuclear power was considered as a sort of transition energy technology until the energy supply would take place by the use of renewable energy sources. This was in line with the legal framework and the political strategy of the energy turnaround. Then, 17 nuclear power plants (NPP) were operational. The Fukushima incident heralded the sound of drastic changes in the German energy policy: Besides an intermediate stop of operation of reactors until a so-called stress test was accomplished, the general political decision was to phase-out nuclear earlier than planned and to implement faster the decisions regarding the energy transition policy. The shut-down of the last German nuclear power plant will occur in 2022. Accordingly, all the necessary legal changes were made. A consensus about the appropriate waste management strategy for heat generating waste (spent nuclear fuel (SNF) and vitrified waste (HLW)) was still pending at this time. Public and political discussions on this subject continued as in the years before. In July 2013, after intensive discussions, most of the parties represented in the German parliament agreed to eventually tackle the challenge of finding a repository by a consensual, transparent and science-based approach. This was to be codified in a law. In July 2013, the Site Selection Act passed the parliament. This law should pave the way for a new holistic process that addresses social, political, and scientific aspects of siting and the site selection process. The basics for this process should be provided by the 'Commission Storage of Radioactive Waste Materials' which was established according this law. Against this background discussions showed that scientific-technical R and D activities should be mirrored accordingly and R and D has to deal both with the future challenges of radioactive waste HLW disposal and related aspects. Considering this the Federal Ministry for Economic Affairs and Energy (BMWi), which is responsible for non-site specific R and D, created the new Research Concept 'Research for the management of radioactive waste', being fundamental and the frame for non-site specific R and D projects funded by BMWi. Key changes - mirroring the new requirements and different aspects - touch the issues: host rock research, i.e. all potential host rocks available in Germany are equally addressed and there is no prioritization, consideration of consequences of prolonged storage at NPP sites, alternative waste management strategies compared to direct disposal in a mined repository, and involvement of socio-technical aspects.This paper intends to highlight the key changes, its consequences, and will give a brief overview on first initiated R and D activities. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

New AREVA's Investment in Continuous Improvement to Increase Efficiency of La Hague Reprocessing Lines - 18588

New AREVA currently operates 2 commercial reprocessing lines at their La Hague facility in France. Each line is capable of reprocessing up to 800 tHM/year of commercial spent light water reactor fuel. The site and process is self-contained with all waste arising from the reprocessing operations segregated into various waste streams and stabilized at the site. New AREVA operates a culture of continuous improvement and continues to invest in new technology, processes, waste management and procedures that have increased plant throughput while reducing waste volumes, operating cost while at the same time maintaining our strong safety culture. New investments have also been driven by changing customer needs and new markets. A good example of this has emerged over the last several years as New AREVA has been transporting a large amount of Research Reactor (RR) Uranium-Aluminum (UAl) type spent fuel (SF) on behalf of international RR operators to the La Hague site. Last year more than 100 RR fuel elements shipments were carried out by New AREVA (for fresh and spent fuel). In our current commercial lines the reprocessing of RRSF has been limited to approximately 1.4 ton a year. To meet increasing demand for reprocessing of RRSF, the range of RRSF that can now be reprocessed at La Hague has been extended to include Uranium-Aluminium-Silicium fuel (USi also called Silicide fuel) and also non-intact RRSF. In addition, New AREVA supported large scale research, development and engineering programs to identify processes/technology to allow the La Hague Facilities to reprocess a targeted average of additional 25 tons/year of non-commercial fuel types (RRSF and also fast reactor fuel, specific MOX fuel... ). A new facility head end called Traitement de Combustibles Particuliers (TCP) facility is currently planned to be implemented in the La Hague plant allowing reprocessed special fuels to be introduced into the existing commercial processing lines. The purpose of the paper is to demonstrate New AREVA's culture of continuous improvement that has been implemented at our commercial reprocessing facility highlighting how we have invested in processes and procedures for improving services to the nuclear operators. A case study will be presented related to our latest development of the TCP head end that will allow New AREVA to reprocess a targeted average of additional 25 tons/year of specialized fuels. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Key Takeaways: First Cohort of Action Plans for Rapid Power Sector Decarbonization

The purpose of this synthesis report is to extract key takeaways from the first cohort of CEM Action Plans for rapid power sector decarbonization, developed by Australia, Chile, the European Union, India, and the United Kingdom. These Action Plans differ in their approach to power sector decarbonization based on the domestic resources available, governance structure, and regional context, among other factors. However, they also share common themes that were emphasized in the collaborative report released at CEM13. This report is not intended to be inclusive of all components in each Action Plan. Rather, this report highlights how select best practices for planning, building, and operating power systems are being implemented differently in these Action Plans, with equal focus given to each jurisdiction. Ministers and stakeholders from other governments with similar decarbonization goals can consider these examples within their own unique context.

Australia↗

SEA monitoring in Swedish regional transport infrastructure plans - Improvement opportunities identified in practical experience

Strategic Environmental Assessment (SEA) requires monitoring in order to identify unforeseen adverse effects and to enable appropriate remedial action to be taken. Guidelines on how to monitor significant environmental impacts have been developed but experience from practice is limited. This paper presents a study of environmental monitoring in Swedish regional transport infrastructure planning. The result shows that essentially no environmental monitoring is currently performed. Monitoring of the plans merely involves checking the implementation of projects and performing an economic account. At present, a new planning period has commenced for the regional transport infrastructure plans. To obtain an iterative SEA process for the new plan with integrated SEA monitoring, the following means are suggested: reinforcement of practitioners' incentives to plan and perform monitoring; integration of monitoring in the SEA process; pre-determined impact thresholds that prompt remedial action; and more efficient use of monitoring results.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗