Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Experimental Study of the Effects of Finite Surface Disturbances and Angle of Attack on the Laminar Boundary Layer of an NACA 64A010 Airfoil with Area Suction

A Langley low-turbulence wind-tunnel investigation of a porous NACA 64A010 airfoil section has been made to determine the effectiveness of area suction in maintaining full-chord laminar flow behind finite disturbances and at angles of attacks other than 0 degrees. Aero suction resulted in only a small increase in the size of a finite disturbance required to cause premature boundary-layer transition as compared with that for the airfoil without suction. Combined wake and suction drags lower than the drag of the plain airfoil were obtained through a range of low lift coefficient by the use of area suction.

FLOW, LAMINAR↗

Hydrodynamic characteristics over a range of speeds up to 80 feet per second of a rectangular modified flat plate having an aspect ratio of 0.25 and operating at several depths of submersion

Results of an investigation of the hydrodynamic characteristics over an extended speed range of a rectangular modified flat plate having an aspect ratio of 0.25 and operating at several depths of submersion are presented. Comparisons between these data and data over a lower speed range on a similar aspect-ratio-0.25 flat plate but having one-half the thickness are presented. These comparisons show no significant differences at the low speeds. At high speeds and high angles of attack, where extensive cavitation was present, the lift coefficients were lower than would have been indicated by the results of the previous investigations and the present investigation at the lower angles of attack. A brief discussion and comparison of ventilation are presented which shows two types of planing bubble formation and the effect of increasing the thickness of the model on the ventilation boundary.

REYNOLDS NUMBER EFFECTS - COMPLETE WINGS↗

Investigation of Minimum Drag and Maximum Lift-drag Ratios of Several Wing-body Combinations Including a Cambered Triangular Wing at Low Reynolds Numbers and at Supersonic Speeds

Theoretical and experimental data for wing-body combinations with wings of triangular, arrow, and diamond plan form are presented for Mach numbers of 1.62, 1.93, and 2.41 and a Reynolds number range of 1.4 x 10 to the 6th power to 0.7 x 10 to the 6th power. Included are two each of triangular and arrow plan-form wings cambered for approximately uniform load at m = 1.62 and lift coefficients of 0.08 and 0.20. Liquid-film studies of the flow over the various configurations are also presented.

Brown, Clinton E↗

Experiments with a Wing Model from which the Boundary Is Removed by Suction

The present report deals with a series of tests made for the purpose of improving flow conditions about wings by applying the suction principle (increase of the lift coefficient and reduction of the drag about very thick wing sections). Though not conclusive, the report contains interesting results.

BOUNDARY LAYER REMOVAL - SUCTION (SCHRENK)↗

Theoretical and Analog Studies of the Effects of Nonlinear Stability Derivatives on the Longitudinal Motions of an Aircraft in Response to Step Control Deflections and to the Influence of Proportional Automatic Control

Through theoretical and analog results the effects of two nonlinear stability derivatives on the longitudinal motions of an aircraft have been investigated. Nonlinear functions of pitching-moment and lift coefficients with angle of attack were considered. Analog results of aircraft motions in response to step elevator deflections and to the action of the proportional control systems are presented. The occurrence of continuous hunting oscillations was predicted and demonstrated for the attitude stabilization system with proportional control for certain nonlinear pitching-moment variations and autopilot adjustments.

Curfman, Howard J , Jr↗

General Theory of the Steady Motion of an Airplane

The writer points out briefly the history of the method proposed for the study of steady motion of an airplane, which is different from other methods now used. M. Paul Painleve has shown how convenient the drag-lift curve was for the study of airplane steady motion. The author later added to the drift-lift curve the curve called the "speed curve" which permits a direct checking of the speed of the airplane under all flying conditions. But the speed curve was plotted in the same quadrant as the drag-lift curve. Later, with the progressive development of aeronautical science, and with the continually increasing knowledge concerning engines and propellers, the author was brought to add the three other quadrants to the original quadrant, and thus was obtained the steady motion chart which is described in detail in this report. This charts permits one to read directly for a given airplane its horizontal speed at any altitude, its rate of climb at any altitude, its apparent inclination to the horizon at any moment, its ceiling, its propeller thrust, revolutions, efficiency, and power absorbed, that is the complete set of quantities involved in the subject, and to follow the variations of all these quantities both for variable altitude and for variable throttle. The chart also permits one to follow the variation of all of the above in flight as a function of the lift coefficient and of the speed. The author also discusses the interaction of the airplane and propeller through the slipstream and the question of the properties of the engine-propeller system and its dependence upon the properties of the engine considered alone and of the propeller considered alone. There is also a discussion of a standard atmosphere.

De Bothezat, George↗

Wind-Tunnel Tests on Airfoil Boundary Layer Control Using a Backward-Opening Slot

This report presents the results of an investigation to determine the effect of boundary layer control on the lift and drag of an airfoil. Boundary layer control was accomplished by means of a backward-opening slot in the upper surface of the hollow airfoil. Air was caused to flow through this slot by a pressure which was maintained inside the airfoil by a blower. Various slot locations, slot openings, and wing pressures were used. The tests were conducted in the 5-foot atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory. Under the test conditions, the maximum lift coefficient was increased about 96 per cent for one slot arrangement, and the minimum drag coefficient was decreased about 27 per cent for another, both being compared with the results obtained with the unslotted airfoil. It is believed from this investigation that the above effects may be increased by the use of larger slot openings, better slot locations, multiple slots, improved airfoil profiles, and trailing edge flaps.

Bamber, Millard J↗

Characteristics of Clark Y airfoils of small aspect ratios

This report presents the results of a series of wind tunnel tests showing the force, moment, and autorotational characteristics of Clark Y airfoils having aspect ratios varying from 0.5 to 3. An airfoil of rectangular plan form was tested with rectangular tips, flared tips, and semicircular tips. Tests were also made on one airfoil of circular plan form and two airfoils of elliptical plan form. The tests revealed a marked delay of the stall and a decided increase in values of maximum lift coefficient and maximum resultant force coefficient for aspect ratios of the order of 1 as compared with values for aspect ratios of 2 and 3.

Zimmerman, C H↗

Wing Pressure Distribution and Rotor-Blade Motion of an Autogiro as Determined in Flight

This report presents the results of tests in which the pressure distribution over the fixed wing of an autogiro was determined in both steady and accelerated flight. In the steady-flight condition, the rotor-blade motion was also measured. These data show that in steady flight the rotor speed as a function of the air speed is largely affected by the variation of the division of load between the rotor and the wing; as the load on the wing increases, the rotor speed decreases. In steady flight the presence of the slipstream increased both the wing lift at a given air speed and the maximum lift coefficient of the wing above the corresponding values without the slipstream. In abrupt high-speed turns, the wing attained a normal force coefficient of unity at almost the initial value of the air speed and experienced its maximum load before maximum acceleration occurred.

Wheatley, John B↗

Relative loading on biplane wings of unequal chords

It is shown that the lift distribution for a biplane with unequal chords may be calculated by the method developed in NACA Technical report no. 458 if corrections are made for the inequality in chord lengths. The method is applied to four cases in which the upper chord was greater than the lower and good agreement is obtained between observed and calculated lift coefficients.

Diehl, Walter S↗

The Influence of Wing Setting on the Wing Load and Rotor Speed of a PCA-2 Autogiro as Determined in Flight

Flight tests were made on PCA-2 autogiro with wing settings of 2.2 degrees, 0.9 degrees, and -0.5 degrees. The wing load and rotor speed were measured in steady glides. The results obtained show that a wide variation in rotor speed as a function of air speed can be obtained by a suitable adjustment of the wing setting; that by decreasing the wing setting the upper safe flying speed, determined by the decrease is rotor speed, is greatly increased; and that the interference of the wing on the rotor thrust and lift coefficients is negligible.

Wheatley, John B↗

The experimental and calculated characteristics of 22 tapered wings

The experimental and calculated aerodynamic characteristics of 22 tapered wings are compared, using tests made in the variable-density wind tunnel. The wings had aspect ratios from 6 to 12 and taper ratios from 1:6:1 and 5:1. The compared characteristics are the pitching moment, the aerodynamic-center position, the lift-curve slope, the maximum lift coefficient, and the curves of drag. The method of obtaining the calculated values is based on the use of wing theory and experimentally determined airfoil section data. In general, the experimental and calculated characteristics are in sufficiently good agreement that the method may be applied to many problems of airplane design.

Anderson, Raymond F↗

Determination of Boundary-Layer Transition on Three Symmetrical Airfoils in the NACA Full-Scale Wind Tunnel

For the purpose of studying the transition from laminar to turbulent flow, boundary-layer measurements were made in the NACA full-scale wind tunnel on three symmetrical airfoils of NACA 0009, 0012, and 0018 sections. The effects of variations in lift coefficient, Reynolds number, and airfoil thickness on transition were investigated. Air speed in the boundary layer was measured by total-head tubes and by hot wires; a comparison of transition as indicated by the two techniques was obtained. The results indicate no unique value of Reynolds number for the transition, whether the Reynolds number is based upon the distance along the chord or upon the thickness of the boundary layer at the transition point. In general, the transition is not abrupt and occurs in a region that varies in length as a function of the test conditions.

Silverstein, Abe↗

The application of basic data on planing surfaces to the design of flying-boat hulls

Basic lift data on planing surfaces have been analyzed and the data applied to the design of flying-boat hulls. It is shown that a balance between air and water forces requires that the beam of the planing area bear a relation to the wing area that is determined by the lift coefficient of the wing and by the angle of dead rise in the planing surface. It is also shown that the fore-and-aft extent of the required planing area depends on the angle of dead rise. Failure to provide sufficient length of planing area appears to be the main reason for the poor water performance sometimes obtained when a large angle of dead rise is used.

Diehl, Walter S↗

Wind-tunnel investigation of an NACA 23012 airfoil with 30 percent-chord venetian-blind flaps

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a NACA 23012 airfoil with 30-percent-chord venetian-blind flaps having one, two, three, and four slats of Clark y section. The three-slat arrangements was aerodynamically the best of those tested but showed practically no improvement over the comparable arrangement used in the preliminary tests published in NACA Technical Report No. 689. The multiple-slat flaps gave slightly higher lift coefficients than the one-slat (Fowler) flap but gave considerably greater pitching-moment coefficients. An analysis of test data indicates that substitution of a thicker and more cambered section for the Clark y slats should improve the aerodynamic and the structural characteristics of the venetian-blind flap.

Rogallo, F M↗

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplane

An investigation was conducted in the NACA full-scale wind tunnel to determine the drag and the propulsive efficiency of nacelle-propeller arrangements for a large range of nacelle sizes. In contrast with usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a four-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplanes weighing from about 20 to 100 tons. The results show the drag, the propulsive efficiency, and the over-all efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model is shown for both propeller-removed and propeller-operating conditions.

Silverstein, Abe↗

Effects of sweepback on boundary layer and separation

Following a law of stress adopted in the Navier-Stokes equations, the configuration of the viscous flow in planes at right angles to the axis of an infinite cylinder is found to be independent of the axial motion of the cylinder. In the limiting case of a yawed or swept wing of very high aspect ratio, certain boundary-layer and separation phenomena are thus determined independently by the crosswise component of velocity. It follows that the effect of sweepback is to increase the area of stable laminar flow and to decrease the lift coefficient at which flow separation occurs.

Jones, Robert T↗

Velocity distributions on two-dimensional wing-duct inlets by conformal mapping

The conformal-mapping method of the Cartesian mapping function is applied to the determination of the velocity distribution on arbitrary two-dimensional duct-inlet shapes such as are used in wing installations. An idealized form of the actual wing-duct inlet is analyzed. The effects of leading edge stagger, inlet-velocity ratio, and section lift coefficients on the velocity distribution are included in the analysis. Numerical examples are given and, in part, compared with experimental data.

Perl, W↗