Search NASA⌕ Search

SEARCH · Search NASA

Results for “Model Linkage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Efficient, Compact, and Smooth Variable Propulsion Motor (Final Report)

In this project, a new architecture of highly efficient hydraulic motor was developed for the propulsion of off-highway vehicles. The motor uses an adjustable linkage driving a cam to vary the displacement of the piston, resulting in a Variable Displacement Linkage Motor (VDLM). The motor uses low friction rolling element bearings to significantly reduce mechanical friction, especially in the demanding low-speed high-torque conditions experienced by off-highway vehicles. The VDLM has high torque capabilities for its size due to the radial piston packaging and use of a multi-lobe cam. A VDLM is very smooth due to the ability to tune the torque ripple through the design of the cam profile. The project was divided into three periods. During the first period, a dynamic model was constructed of the motor to predict the performance of the motor and the vehicle. During the second period, a single-cylinder learning prototype was designed, built, and tested to validate the models constructed in the first period. In the third period, a multi-cylinder prototype motor was optimized, designed, fabricated, and tested. The motor demonstrated excellent mechanical efficiency (above 92.5% across the range of displacements), but the experimentally measure volumetric efficiency was lower than expected due to higher leakage rates created by the poor tolerance control on the prototype. To validate the dynamic models developed in the first period and better understand design trade-offs. In the third period a multi-cylinder concept demonstration prototype will be designed, fabricated, and tested. The final prototype will be tested on a motor dynamometer and will be utilized in hardware-in-the-loop testing to demonstrate its efficiency and performance impacts on the overall drive train. The experimental results were used in a drive train simulation of a compact track loader operating through a drive cycle. Using the VDLM in a hydrostatic circuit yielded 17.1% reduction in fuel consumption and 36.5% reduction in a series hybrid transmission.

99 GENERAL AND MISCELLANEOUS↗

Radical Coupling Reactions of Hydroxystilbene Glucosides and Coniferyl Alcohol: A Density Functional Theory Study

The monolignols, p-coumaryl, coniferyl, and sinapyl alcohol, arise from the general phenylpropanoid biosynthetic pathway. Increasingly, however, authentic lignin monomers derived from outside this process are being identified and found to be fully incorporated into the lignin polymer. Among them, hydroxystilbene glucosides, which are produced through a hybrid process that combines the phenylpropanoid and acetate/malonate pathways, have been experimentally detected in the bark lignin of Norway spruce (Picea abies). Several interunit linkages have been identified and proposed to occur through homo-coupling of the hydroxystilbene glucosides and their cross-coupling with coniferyl alcohol. In the current work, the thermodynamics of these coupling modes and subsequent rearomatization reactions have been evaluated by the application of density functional theory (DFT) calculations. The objective of this paper is to determine favorable coupling and cross-coupling modes to help explain the experimental observations and attempt to predict other favorable pathways that might be further elucidated via in vitro polymerization aided by synthetic models and detailed structural studies.

59 BASIC BIOLOGICAL SCIENCES↗

Coupling Electric Vehicles and Power Grid through Charging-In-Motion and Connected Vehicle Technology

A traffic-assignment-based framework is proposed to model the coupling of transportation network and power grid for analyzing impacts of energy demand from electric vehicles on the operation of power distribution. Although the reverse can be investigated with the proposed framework as well, electricity flowing from a power grid to electric vehicles is the focus of this paper. Major variables in transportation network (including link flows) and power grid (including electricity transmitted) are introduced for the coupling. Roles of charging-in-motion technology and connected vehicle technology have been identified in the framework of supernetwork. A linkage (i.e. individual energy demand) between the two networks is defined to construct the supernetwork. To determine equilibrium of the supernetwork can also answer how many drivers are going to use the charging-in-motion services, in which locations, and at what time frame. An optimal operation plan of power distribution will be decided along the determination simultaneously by which we have a picture about what level of power demand from the grid is expected in locations during an analyzed period. Caveat of the framework and possible applications have also been discussed.

charging in-motion↗

Advanced Simulation Capability for Environmental Management - Current Status and Phase II Demonstration Results - 13161

The U.S. Department of Energy (US DOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Tool-sets and High-Performance Computing (HPC) Multi-process Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial tool-sets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations, addressing attenuation-based remedies at the Savannah River Site F Area and performance assessment for a representative waste tank, illustrate integration of linked ASCEM capabilities and initial integration efforts with tools from the Cementitious Barriers Partnership. (authors)

54 ENVIRONMENTAL SCIENCES↗

Evolutionarily conserved linkage between enzyme fold, flexibility, and catalysis

Proteins are intrinsically flexible molecules. The role of internal motions in a protein's designated function is widely debated. The role of protein structure in enzyme catalysis is well established, and conservation of structural features provides vital clues to their role in function. Recently, it has been proposed that the protein function may involve multiple conformations: the observed deviations are not random thermodynamic fluctuations; rather, flexibility may be closely linked to protein function, including enzyme catalysis. We hypothesize that the argument of conservation of important structural features can also be extended to identification of protein flexibility in interconnection with enzyme function. Three classes of enzymes (prolyl-peptidyl isomerase, oxidoreductase, and nuclease) that catalyze diverse chemical reactions have been examined using detailed computational modeling. For each class, the identification and characterization of the internal protein motions coupled to the chemical step in enzyme mechanisms in multiple species show identical enzyme conformational fluctuations. In addition to the active-site residues, motions of protein surface loop regions (>10 away) are observed to be identical across species, and networks of conserved interactions/residues connect these highly flexible surface regions to the active-site residues that make direct contact with substrates. More interestingly, examination of reaction-coupled motions in non-homologous enzyme systems (with no structural or sequence similarity) that catalyze the same biochemical reaction shows motions that induce remarkably similar changes in the enzyme substrate interactions during catalysis. The results indicate that the reaction-coupled flexibility is a conserved aspect of the enzyme molecular architecture. Protein motions in distal areas of homologous and non-homologous enzyme systems mediate similar changes in the active-site enzyme substrate interactions, thereby impacting the mechanism of catalyzed chemistry. These results have implications for understanding the mechanism of allostery, and for protein engineering and drug design.

59 BASIC BIOLOGICAL SCIENCES↗

Integration of Photovoltaics into Building Energy Usage through Advanced Control of Rooftop Unit

This paper presents a computational approach to forecast photovoltaic (PV) power in kW based on a neural network linkage of publicly available cloud cover data and on-site solar irradiance sensor data. We also describe a control approach to utilize rooftop air conditioning units (RTUs) to support renewable integration. The PV forecasting method is validated using data from a rooftop PV panel installed on the Distributed Energy, Communications, and Controls (DECC) laboratory at Oak Ridge National Laboratory. The validation occurs in multiple phases to ensure that each component of the approach is the best representation of the actual expected output. The control of the RTU is based on model predictive methods.

Starke, Michael R↗

Enhanced delignification of steam-pretreated poplar by a bacterial laccase

The recalcitrance of woody biomass, particularly its lignin component, hinders its sustainable transformation to fuels and biomaterials. Although the recent discovery of several bacterial ligninases promises the development of novel biocatalysts, these enzymes have largely been characterized using model substrates: direct evidence for their action on biomass is lacking. Herein, we report the delignification of woody biomass by a small laccase (sLac) from Amycolatopsis sp . 75iv3. Incubation of steam-pretreated poplar (SPP) with sLac enhanced the release of acid-precipitable polymeric lignin (APPL) by ~6-fold, and reduced the amount of acid-soluble lignin by ~15%. NMR spectrometry revealed that the APPL was significantly syringyl-enriched relative to the original material (~16:1 vs. ~3:1), and that sLac preferentially oxidized syringyl units and altered interunit linkage distributions. sLac’s substrate preference among monoaryls was also consistent with this observation. In addition, sLac treatment reduced the molar mass of the APPL by over 50%, as determined by gel-permeation chromatography coupled with multi-angle light scattering. Finally, sLac acted synergistically with a commercial cellulase cocktail to increase glucose production from SPP ~8%. Altogether, this study establishes the lignolytic activity of sLac on woody biomass and highlights the biocatalytic potential of bacterial enzymes.

59 BASIC BIOLOGICAL SCIENCES↗

Description of Axial Detail for ROK Fuel

For the purpose of NDA simulations of the ROK fuel assemblies, we have developed an axial burnup distribution to represent the pins themselves based on gamma scans of rods in the G23 assembly. For the purpose of modeling the G23 assembly (both at ORNL and LANL), the pin-by-pin burnup map as simulated by ROK is being assumed to represent the radial burnup distribution. However, both DA and NDA results indicate that this simulated estimate is not 100% correct. In particular, the burnup obtained from the axial gamma scan of 7 pins does not represent exactly the same 'average' pin burnup as the ROK simulation. Correction for this discrepancy is a goal of the well-characterized assembly task but will take time. For now, I have come up with a correlation for 26 axial points of the burnup as obtained by gamma scans of 7 different rods (C13, G01, G02, J11, K10, L02, and M04, neglecting K02 at this time) to the average burnup given by the simulation for each of the rods individually. The resulting fraction in each axial zone is then averaged for the 7 different rods so that it can represent every fuel pin in the assembly. The burnup in each of the 26 axial zones of rods in all ROK assemblies will then be directly adjusted using this fraction, which is given in Table 1. Note that the gamma scan data given by ROK for assembly G23 included a length of ~3686 mm, so the first 12 mm and the last 14 mm were ignored to give an actual rod length of ~366 cm. To represent assembly F02 in which no pin-by-pin burnup distribution is given by ROK, we must model it using infinitely-reflected geometry but can look at the effects of measuring in different axial zones by using intermediate burnup files (i.e. smaller burnups than 28 GWd/MTU) and determining which axial zone(s) each burnup represents. Details for assembly F02 are then given in Tables 2 and 3, which is given in Table 1 and has 44 total axial zones to represent the top meter in explicit detail in addition to the other 26 zones. Note that the MCNP files for F02 were created using the Monte Carlo burnup linkage code Monteburns, which saves MCNP input files with detailed compositions as a function of burnup. The 'intermediate burnup files' produced for F02 include a cooling time of 27 years. The axial location of 5 spacers was also included in the ROK F02 assembly in which each spacer contained a length of 3.81 cm. Note that due to the nature of Monteburns, which was run in a special fashion for this problem, the step number increments after the 27 year decay, so the second column of Table 2 refers to the step number that should be used in the Monteburns files.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Low-Cost Heliostat for High-Flux Small-Area Receivers (Final Technical Report)

This project analyzed a two-stage heliostat concept consisting of a tracking stage and a concentrating stage. The tracking stage uses mirrors mounted on a common drive that move to track the sun. The concentrating stage consists of stationary mirrors that each have a unique angle to direct rays towards a small-area, high-flux, point-focused receiver. By splitting the collection and concentrating process into two stages, multiple small, inexpensive mirrors can share a structure and be controlled by a single drive in the tracking stage. The project effort developed modeling techniques that were specifically relevant to this two-stage heliostat concept. Both field-level and unit-level models were developed. The field-level model does not explicitly consider unit-level losses which are predicted by the unit-level model and then integrated into the field-level model through a correlation referred to as an efficiency modifier. This approach is referred to as the two-model approach; the development and demonstration of this two-model approach for a multi-stage heliostat technology is a key outcome of this work. The field-level model is used to design a field that hits a specific design day power given a set of heliostat design parameters. An oversized field is simulated and then heliostat units are removed based on their annual energy production in order to generate the highest performing field. The field reduction procedure fits a smooth curve fit to annual energy production as a function of position in the field which has the effect of reducing the noise that is otherwise caused by the Monte Carlo ray tracing technique. This approach is referred to as the annual energy fit method and substantially reduces computational run time for a given field level modeling accuracy. The annual energy fit approach enables the selection of a properly sized, high-performing field using orders of magnitude fewer rays than would otherwise be possible and the development of this approach is a second key outcome of this work. These models are used within a genetic optimization algorithm in order to optimize the geometric parameters associated with a heliostat in order to achieve the lowest cost per unit of collected design day power. The cost modeling that underlies the optimization is a simple, scaling type analysis backed up by a much more detailed Design for Manufacture and Assembly (DFMA) analysis. Although the figure of merit used for optimization was not cost per mirror area, this metric is reasonable to use as a means of comparison. The optimally designed 500 kW design has a tracking mirror specific cost of $181.85/m 2 , which is significantly larger than the target value and also larger than the current state of the art. The cost of the torque-tube type linkages contributed substantially to the overall cost. Based on this observation, potentially attractive alternative design configuration utilizing a capstan type actuation system should be investigated. Finally, NREL compared the performance of the two-stage heliostat to the performance of a focused and different sized flat conventional heliostats and showed that, as expected, additional losses versus the convention heliostat caused by a worse cosine efficiency, two stages of reflection, and interstage interactions. The two-stage heliostat requires around 75% more reflective area than a flat 1x1 meter conventional heliostat (similar to a focused heliostat) and 40% more than a flat 2x2 meter conventional heliostat.

14 SOLAR ENERGY↗

An implementable digital adaptive flight controller designed using stabilized single stage algorithms

Simple mechanical linkages have not solved the many control problems associated with high performance aircraft maneuvering throughout a wide flight envelope. One procedure for retaining uniform handling qualities over such an envelope is to implement a digital adaptive controller. Towards such an implementation an explicit adaptive controller which makes direct use of on-line parameter identification, has been developed and applied to both linearized and nonlinear equations of motion for a typical fighter aircraft. This controller is composed of an on-line weighted least squares parameter identifier, a Kalman state filter, and a model following control law designed using single stage performance indices. Simulation experiments with realistic measurement noise indicate that the proposed adaptive system has the potential for on-board implementation.

Kaufman, H.↗

Dilation Behavior of Thermal Spray Coatings

The thermal expansion of a thermally sprayed coating material is an important design-relevant property from both processing and application service points of view. High thermal stresses and residual strains can arise during deposition, and thermal exposure in service. The linkage to process conditions which can impact both physical and chemical attributes of the microstructure and consequently its expansion behavior is of great importance. The observed dilation response of various coatings is discussed based on the processing effects that induce differences in microstructural features and the impact of residual strain and annealing of defects on the dilation behavior during first thermal exposure. The coefficient of thermal expansion (CTE) of coatings was found to approach the bulk when the material is not sensitive to oxidation in-flight. For those materials sensitive to oxidation, mathematical models used to describe effective properties of composite materials were adopted to describe the CTE property. A large irreversible dilation change was found in the first heating cycle due to defect annealing (referred to as thermal shakedown). Several reasons are hypothesized for the magnitude of such dilation change. Finally, together, the paper presents a comprehensive analysis of thermal expansion behavior of a diversity of thermal spray processed materials.

36 MATERIALS SCIENCE↗

The Dynamics of 1, 3 diphenylpropane Tethered to the Interior Pore Surfaces of MCM-41

The diffusive motions of covalently tethered 1, 3 diphenylpropane (DPP) via a silyl-aryl-ether linkage in the mesopores of MCM-41 were studied by quasielastic neutron scattering. The geometric effect of pore radius was investigated with samples having pores that ranged from 1.6 to 3.0 nm in diameter and highest achievable DPP grafting density. The effect of molecular crowding was investigated in 3.0 nm diameter pores for surface coverage ranging from 0.60 to 1.61 DPP/nm2. Temperature dependence was determined for large pore diameter samples from 240 K to 370 K. As the DPP molecules remain attached over this entire temperature range, data were analyzed in terms of a model of localized diffusion inside a sphere. Only the motions of the DPP hydrogen atoms were considered because of the high sensitivity of neutron scattering to the presence of hydrogen. As atoms far from the attachment point have a greater range of motion than those nearer the tether, the radius of the sphere limiting the motion of individual hydrogen atoms was allowed to increase based on the atom s distance from the tether point. Both smaller pore diameters and higher DPP surface coverage resulted in larger amplitude motion while the diffusion coefficient was greatest in the largest pores at highest surface coverage. These observations support a model where the DPP molecules prefer an orientation allowing close proximity to the MCM-41 pore surface and are forced into the pore interior by either the steric effect of small pore diameter or by increased competition for surface area at high molecule surface coverage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scientific Core Library Stack (SCLS) v2026

SCLS (Scientific Core Library Stack) is an opinionated build and packaging system for scientific computing libraries developed at Lawrence Berkeley National Laboratory. It produces a coherent, reproducible stack of numerical libraries — including BLAS/LAPACK, MPI, sparse direct and iterative solvers, graph partitioners, and parallel I/O libraries (e.g., PETSc, SLEPc, HDF5, NetCDF, MUMPS, OpenBLAS) — that work together without manual repair by downstream scientific software. From a single recipe-and-flavor model, SCLS produces native RPM packages for RHEL-family Linux, DEB packages for Debian/Ubuntu, direct Unix-style prefix installs for HPC and locked-down environments, and native macOS builds. Multiple build "flavors" (e.g., GCC+OpenBLAS, GCC+MKL, Intel+MKL, debug) coexist in distinct prefixes on the same host. Compared to general-purpose meta-build frameworks, SCLS is deliberately curated rather than infinitely configurable. It enforces deterministic, audit-friendly behavior: explicit build dependencies, no silent feature autodetection, a clear open-source license policy, and rpath-based runtime linkage so installs integrate cleanly with standard package-manager workflows.

Messe, Christian [Lawrence Berkeley National Labor↗

Manufacturing of Fabric Electrodes using a High-Throughput Screening Platform for Redox Flow Batteries

The objective of this project is to establish a new manufacturing methodology with machine learning- based high-throughput screening for the design and development of hierarchical structured, high-performance fabric electrodes for redox flow batteries (RFBs). The end goal of the project is to design and manufacture fabric electrodes for RFB applications that can provide 250 mA/cm2 current density operation for 100-cycles with 80% average energy efficiency. This was accomplished by first examining the structure-performance-property linkages of the electrodes provided by our partner, AvCarb. The electrodes’ microstructure was characterized by determining their pore size distribution, tortuosity, specific surface area, and porosity. The ohmic, charge transfer and mass transfer resistances were then calculated using electrochemical impedance spectroscopy. Carbon cloth electrodes showed the greatest resistance, which was dominated by charge transfer resistance, which we believe is related to the surface functionalization. Full cell cycling was used in order to determine the area specific resistance and energy efficiency of the cells. All of this experimental data and the results of the mathematical model (to increase the amount of inputs with parametric sweeping) were used to develop a machine learning-based model for the design of high-performance fabric electrodes. Using the results from the machine learning tool, optimized electrodes were fabricated by AvCarb. The ohmic, charge transfer and mass transfer resistances for these new electrodes were measured, and both performed better than any of the initial samples which had been provided by AvCarb.

25 ENERGY STORAGE↗

Sputtering Erosion in the Ion Thruster

During the first phase of this research, the sputtering yields of molybdenum by low energy (100 eV and higher) xenon ions were measured by using the methods of secondary neutral mass spectrometry (SNMS) and Rutherford backscattering spectrometry (RBS). However, the measured sputtering yields were found to be far too low to explain the sputtering erosions observed in the long-duration tests of ion thrusters. The only difference between the sputtering yield measurement experiments and the ion thruster tests was that the later are conducted at high ion fluences. Hence, a study was initiated to investigate if any linkage exists between high ion fluence and an enhanced sputtering yield. The objective of this research is to gain an understanding of the causes of the discrepancies between the sputtering rates of molybdenum grids in an ion thruster and those measured from our experiments. We are developing a molecular dynamics simulation technique for studying low-energy xenon ion interactions with molybdenum. It is difficult to determine collision sequences analytically for primary ions below the 200 eV energy range where the ion energy is too low to be able to employ a random cascade model with confidence and it is too high to have to consider only single collision at or near the surface. At these low energies, the range of primary ions is about 1 to 2 nm from the surface and it takes less than 4 collisions on the average to get an ion to degrade to such an energy that it can no longer migrate. The fine details of atomic motion during the sputtering process are revealed through computer simulation schemes. By using an appropriate interatomic potential, the positions and velocities of the incident ion together with a sufficient number of target atoms are determined in small time steps. Hence, it allows one to study the evolution of damages in the target and its effect on the sputtering yield. We are at the preliminary stages of setting up the simulation program.

Ray, Pradosh K.↗

Interfacial bond characterization of epoxy adhesives to aluminum alloy and carbon fiber-reinforced polyamide by vibrational spectroscopy

Vibrational spectroscopic technique has been utilized to investigate interfacial bonding chemistry of two epoxy adhesive products, XP0012 and XP5005F, on plasma-treated AA6061 and carbon fiber-reinforced polyamide 66 (CFRP-PA66) surfaces. The change in vibrational peak ratios was measured by attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy to deduce bonding mechanisms. Both adhesives showed strong crosslinking polymerization of hydroxyl- and amine-initiated epoxy ring opening on AA6061 surface, but on CFRP surface XP0012 formed a simple amide linkage by the reaction of surface hydroxyl groups and nitrile groups of curing agent, and XP5005F formed a crosslinked network by hydroxyl-initiated epoxy ring opening polymerization. The different interfacial bonding formation of two adhesives on CFRP-PA66 surface is attributed to additive effect. Addition of additives to epoxy adhesives (XP5005F) changed the interfacial bonding mechanism on CFRP-PA66 surface, rather forming hydroxyl-initiated epoxy opening crosslinking polymerization than a simple amide bond formation (XP0012). The interfacial bonding chemistry was also proved by addition of bisphenol A (BA) to a simplified model diglycidyl ether of bisphenol A/dicyandiamide (DGEBA/DICY) epoxy system. When BA was added to the model DGEBA/DICY system, epoxy ring gradually decreased on CFRP-PA66 surface, while without BA, DGEBA/DICY showed only decrease in a nitrile peak intensity in ATR-FTIR. In conclusion, the foregoing different types of interfacial chemical bonds at the adhesive/CFRP-PA66 interfaces can affect the lap shear behavior of the joint.

36 MATERIALS SCIENCE↗

Speciation and Introgression between Mimulus nasutus and Mimulus guttatus

Mimulus guttatus and M. nasutus are an evolutionary and ecological model sister species pair differentiated by ecology, mating system, and partial reproductive isolation. Despite extensive research on this system, the history of divergence and differentiation in this sister pair is unclear. We present and analyze a population genomic data set which shows that M. nasutus budded from a central Californian M. guttatus population within the last 200 to 500 thousand years. In this time, the M. nasutus genome has accrued genomic signatures of the transition to predominant selfing, including an elevated proportion of nonsynonymous variants, an accumulation of premature stop codons, and extended levels of linkage disequilibrium. Despite clear biological differentiation, we document genomic signatures of ongoing, bidirectional introgression. We observe a negative relationship between the recombination rate and divergence between M. nasutus and sympatric M. guttatus samples, suggesting that selection acts against M. nasutus ancestry in M. guttatus.

59 BASIC BIOLOGICAL SCIENCES↗

A Probabilistic Framework for the Validation and Certification of Computer Simulations

The paper presents a methodology for quantifying, propagating, and managing the uncertainty in the data required to initialize computer simulations of complex phenomena. The purpose of the methodology is to permit the quantitative assessment of a certification level to be associated with the predictions from the simulations, as well as the design of a data acquisition strategy to achieve a target level of certification. The value of a methodology that can address the above issues is obvious, specially in light of the trend in the availability of computational resources, as well as the trend in sensor technology. These two trends make it possible to probe physical phenomena both with physical sensors, as well as with complex models, at previously inconceivable levels. With these new abilities arises the need to develop the knowledge to integrate the information from sensors and computer simulations. This is achieved in the present work by tracing both activities back to a level of abstraction that highlights their commonalities, thus allowing them to be manipulated in a mathematically consistent fashion. In particular, the mathematical theory underlying computer simulations has long been associated with partial differential equations and functional analysis concepts such as Hilbert spares and orthogonal projections. By relying on a probabilistic framework for the modeling of data, a Hilbert space framework emerges that permits the modeling of coefficients in the governing equations as random variables, or equivalently, as elements in a Hilbert space. This permits the development of an approximation theory for probabilistic problems that parallels that of deterministic approximation theory. According to this formalism, the solution of the problem is identified by its projection on a basis in the Hilbert space of random variables, as opposed to more traditional techniques where the solution is approximated by its first or second-order statistics. The present representation, in addition to capturing significantly more information than the traditional approach, facilitates the linkage between different interacting stochastic systems as is typically observed in real-life situations.

Ghanem, Roger↗