Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optical microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Understanding interfacial crystallization dynamics on carbon fiber reinforced polypropylene composite manufacturing

Reinforcing polymers with discontinuous fibers improves mechanical properties, such as strength and stiffness, and in some cases achieve isotropic properties, rendering them suitable for various engineering applications. Matrix materials are generally highly engineered thermosets (e.g. crosslinked epoxies), bonded to the fiber periphery by proprietary surface and sizing chemistries. Semicrystalline thermoplastic matrices are less utilized due to poor fiber-matrix bonding resulting in inefficient interfacial load-transfer in reinforced composites. However, flexibility with melt-processing or molding conditions can be leveraged to promote non-covalent interfacial bonding between matrix and fiber via crystallization of the matrix onto fiber surface. In the present study, we utilize a co-mingle chopped carbon and isotactic polypropylene fibers to form isotropic composites, tailoring interfacial immobilized matrix or interphase morphology to optimize performance through precise control of thermal processing/molding windows. Calorimetry and optical microscopy were employed to investigate the impact of carbon fiber at various volume fractions (10, 20, and 30 %) on isotactic polypropylene crystallization and mechanical performance. Variations in mechanical properties correspond to the structural evolution of the interfacial region and are correlated to underlying microstructural attributes using wide-angle X-ray scattering, thermal analysis, and low-field nuclear magnetic resonance spectroscopy. These results provide a practical framework for the manufacturing of thermoplastic matrix composites. In conclusion, the results presented provide a guide for the strategic optimization of interphase design, showcasing tailorable tensile strengths which outperform any isotactic polypropylene carbon fiber composites previously reported in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Experimental and computational analysis of failure mechanisms in unidirectional carbon fiber reinforced polymer laminates under longitudinal compression loading

Here, his study investigates the failure mechanisms of notched unidirectional (UD) carbon fiber reinforced polymer (CFRP) laminates subjected to longitudinal compressive loading. A sequence of failure initiation and propagation is observed based on optical microscopy images of specimens during failure. The micrographs reveal that the main failure mechanism in UD laminates is fiber kinking failure. The influence of manufacturing defects and voids on fiber kinking mechanisms is also analyzed. The results show that the voids in the resin-rich area lead to kink-band splitting, while in some cases the voids cause the kink-band to deflect in a new direction depending on the location of the voids. The next focus of this study is to propose a computational micromechanics model considering local fiber waviness to study the fiber kinking failure mechanism. The computational results on kink-band formation and stress-strain response show good consistency with our experimental analysis. Lastly, the failure envelopes of σ 11 -σ 22 and σ 11 -τ 12 subjected to combined loading conditions are obtained from the computational model, which provide essential inputs for future theoretical failure criteria.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stirring and peristaltic pumping alter flow electrode particle size and morphology

Flowable carbon-based electrodes are widely studied in electrochemical systems for energy storage and water treatment. Most laboratory- and pilot-scale studies employ active mixing for slurry preparation and handling and use peristaltic pumps for slurry circulation. Magnetic stirring is the most prevalent mixing method at the laboratory scale, and the combination of magnetic mixing and peristaltic pumping is favored for convenience and compatibility with particulate suspensions. However, these methods can strongly affect particle size and morphology (and therefore cell performance). In this study, we evaluate how mixing and pumping influence particle degradation in two commonly used carbon materials: spherical carbon black (CB) beads and powdered activated carbon (AC). We performed 24 h stirring-only experiments using magnetic, orbital, and overhead stirring. Separately, we conducted 32 h circulation experiments using a commercial peristaltic pump. Particle morphology and size were analyzed using optical microscopy and laser diffraction. The initially spherical CB beads (~580 μm, 1.5 wt%) exhibit rapid and extensive breakdown under both peristaltic pumping and magnetic stirring. By comparison, AC particles (initially ~31 μm) tested at 1.5 and 15 wt% showed measurable size reductions of up to ~25 % under either stirring or pumping. In conclusion, these findings highlight the need to account for and quantify morphological changes caused by both stirring and pumping in the design and associated evaluation of flowable electrode systems.

Chemistry↗
DOE OSTI2020

Crack nucleation and growth during dynamic indentation of chemically-strengthened glass

Dynamic point impact loading is a primary cause of fracture of glass screens on mobile devices. An improved understanding of crack initiation and evolution under high-speed indentation could contribute to the development of materials with better performance, but experimental observations are challenging due to the short timescales and limited depth-of-field of optical microscopy. To address this need, we have observed fracture of a chemically-strengthened glass during dynamic indentation using in situ x-ray phase-contrast imaging (XPCI). Median cracks initiate below the surface of the glass, at a depth approximately corresponding to the depth at which the surface residual compressive stress diminishes to zero. These cracks initially propagate at ~10ms –1 , rapidly accelerating to > 100ms –1 . We also observe some evidence for rate-dependent behavior, in that indentation at the lowest rates studied here (below about ~0.15ms –1 ) fails to initiate cracks regardless of the depth of the indentation (up to 18μm), while indentation at higher rates produces median cracks that either arrest or cause complete fracture, depending on the depth of indentation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Highly resolved Eulerian simulations of fuel spray transients in single and multi-hole injectors: Nozzle flow and near-exit dynamics

In high pressure fuel injectors, needle opening and closing transients cause complex off-design fluid dynamics behaviors that profoundly impact the spray and mixture formation processes. These dynamics are completely different from what is known to occur in steady state conditions. In this study, diesel spray transients have been investigated in single-hole and 3-hole nozzles, encompassing internal and external nozzle flow and including needle motion, performing highly resolved (2.5 μm) computational fluid dynamics (CFD) simulations. We focused on end-of-injection (EOI) and start-of-injection (SOI) processes, in order to provide insights in to the physics. The liquid fuel, vapor and gas species are modeled with a single-fluid multiphase mixture approach, with diffuse interface, and with large eddy simulations (LES) of the turbulence. Occurrence of phase change due to cavitation is accounted for, and the spray dispersion is described with a turbulent dispersion model. Detailed needle motion data and orifice internal surface are available from xray synchrotron source measurements carried out at Argonne National Laboratory, and shared through the Engine Combustion Network (ECN) community. Simulations are compared against x-ray phase contrast imaging and radiography of the internal and near-exit flow, in addition to optical microscopy data of the near-exit sprays. Simulation results are found to agree well with available experimental data, and are able to realistically capture local and global features. The simulations allow to gain insight into the physics of gas ingestion and dribbles at EOI, for different hole diameters, operating conditions and number of holes. At SOI, timing of liquid appearance out of the injector and spray tip penetration are adequately predicted, by using the EOI flow field as in-nozzle initialization, and by prescribing the measured tip needle displacement with an informed effective valve opening point inferred from the x-ray observations. Lastly, the variation of spreading angle over time is also discussed in detail for the multi-hole case, including hole-to-hole variations. Due to real geometry features and asymmetric needle motion with eccentric components, it is found that the three holes exhibit swirling flows of increasing intensity as the lift decreases, causing the near cone angle to open and spread, in a quasi-hollow cone structure. These features are not observed in axial single-hole injectors because of their relative simplicity and intrinsic symmetry.

42 ENGINEERING↗
DOE OSTI2019

Novel ductile wellbore cementitious composite for geologic CO 2 storage

CO 2 leakage through damaged wellbore cement sheaths is a major risk of geologic CO 2 storage (GCS), as conventional wellbore cement is brittle and can be damaged due to acid attack and downhole stresses during CO 2 injection. Here we examine a novel fiber-reinforced engineered cementitious composite (ECC) proposed as a substitute to conventional wellbore cement due to its superior ductility and intrinsic crack width control. ECC and conventional wellbore cement coupons were exposed to water in equilibrium with CO 2 at 50 °C and 10 MPa. The samples were retrieved after several days and their mechanical performance was evaluated using a four-point bending test, microhardness, and compressive strength analyses. Optical microscopy and mercury intrusion porosimetry were used to characterize the progression of the carbonation front and pore structures of the specimens. Control experiments were conducted under the same temperature and pressure conditions but with a N 2 headspace to isolate the impact of CO 2 . It was found that carbonation increased the ultimate flexural strength of ECC but decreased its ductility. However, the ductility of carbonated ECC remained higher than that of conventional wellbore cements that exhibited brittle failure under all test conditions. Additionally, ECC exhibited minimal material loss and continued resistance to deformation in comparison to conventional wellbore cements. This suggests that while the exposure of ECC to CO 2 will alter its mechanical properties, altered ECC will continue to exhibit mechanical performance superior to conventional wellbore cement, and therefore shows promise as a highly durable wellbore cementing material for GCS applications.

58 GEOSCIENCES↗
DOE OSTI2022

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗
DOE OSTI2025

Linking structure to performance: Characterization of porous transport layers for high-pressure water electrolysis

Proton exchange membrane (PEM) water electrolysis is a promising technology to produce cost-efficient hydrogen. PEM electrolyzers offer a large current density range and the ability to operate at differential pressure which can be used to minimize both capital and operational expenditures. However, directly producing pressurized hydrogen at the cathode results in pushing the membrane against the anode porous transport layer (PTL). This can lead to detrimental effects, such as membrane deformation or ruptures, which depend on membrane properties as well as PTL material properties such as pore size, structure, and morphology. In this work, a range of sinter and felt-based commercial PTLs are evaluated for their contributions to the cell's electrochemical and H 2 crossover performance at cathode pressures up to 30 bar. X-ray tomography and post-operando optical microscopy are used to assess the morphology of the PTLs, and the PTL induced deformation experienced by the catalyst coated membrane (CCM), respectively. PTL samples with lower porosity were found to reduce both the cell voltage and the amount of H 2 permeating from the cathode to the anode exhaust, which was ascribed to improved catalyst layer contact and reduced membrane deformation, respectively. The best performing PTLs improved electrolyzer efficiency by ~1.5 kWh/kg H2 . Specifically, 1 kWh/kg H2 was gained due to reducing membrane deformation and decreasing H 2 crossover. The remainder 0.5 kWh/kg H2 were achieved by improving the electrical contact at the electrode/PTL interface which decreased cell voltage.

08 HYDROGEN↗
DOE OSTI2015

Hexagonal OsB 2 : Sintering, microstructure and mechanical properties

In this study, the metastable high pressure ReB 2 -type hexagonal OsB 2 bulk ceramics was produced by spark plasma sintering. The phase composition, microstructure, and mechanical behavior of the sintered OsB 2 were studied by X-ray diffraction, optical microscopy, TEM, SEM, EDS, and nanoindentation. The produced ceramics was rather porous and contained a mixture of hexagonal (~80 wt.%) and orthorhombic (~20 wt.%) phases as identified by X-ray diffraction and EBSD analysis. Two boron-rich phases, which do not contain Os, were also identified by TEM and SEM/EDS analysis. Nanoindentation measurements yielded a hardness of 31 ± 9 GPa and Young’s modulus of 574 ± 112 GPa, indicating that the material is rather hard and very stiff; but, it is very prone to crack formation and propagation, which is indicative of a very brittle nature of this material. Improvements in the sintering regime are required in order to produce dense, homogeneous and single phase hexagonal OsB 2 bulk ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Recycled polyethylene and crumb rubber composites modified asphalt with improved aging resistance and thermal stability

Crumb rubbers (CR) and recycled Polyethylene (PE) are commonly used as modifiers to improve the asphalt properties. However, the addition of these modifiers individually may result in phase separation of PE and inadequate degradation of CR, which may not simultaneously satisfy the rheological and aging resistance of the binder blends. In this study, a type of CR/PE composites manufactured through melt extrusion procedures was adopted for the improvement of the modified binder blends. The modified binder blends after short-term (RTFO) and long-term (PAV) aging were collected for dynamic shear rheometer and bending beam rheometer tests. FTIR tests were also used to quantify the aging resistance, while differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were applied to evaluate the thermal behaviors of the binder blends. Optical microscopy tests were used to explore the modification mechanism and visualize the microstructures of original and PAV aged binder blends. Test results showed that CR/PE composites could significantly improve the aging resistance of the binder blends. The dispersed PE particles still interacted with each other and meanwhile worked with the diffused rubbery phase, which could form a similar TPEs network. The oxidation and high-temperature aging of such binder blends would strengthen the network that resisted the aging severity of the binder blends. Furthermore, it was also revealed that CR/PE modified asphalt could sustain more heat before a rapid degradation and the well-dispersed PE particles could interact with the diffused CR particles to form a network to resist aging.

02 PETROLEUM↗
DOE OSTI2024

Hybrid additive manufacturing of AISI 316L via asynchronous powder and hot-wire laser directed energy deposition

Hybrid Additive Manufacturing (AM) offers a way to leverage the advantages of different AM technologies, enabling the efficient production of sizeable parts without compromising material properties or geometric complexity capabilities. This study presents an asynchronous hybrid Directed Energy Deposition (DED) strategy employing laser powder DED and laser hot-wire DED. AISI 316L parts comprising multiple powder and wire segments were fabricated with optional machining on AISI 316L substrates to investigate how quality is impacted by (i) alternative process sequences (laser powder DED followed by laser hot-wire DED and vice versa), (ii) machined vs. as-printed interfacial conditions, and (iii) material deposition on top vs. alongside previously built segments. Optical microscopy, X-ray computed tomography, and Vickers hardness were used to characterize the morphology and microstructure of the parts, localized porosity and lack of fusion defects, bulk density, and mechanical properties. Interfacial machining was necessary for dimensional control but promoted lack of fusion voids, resulting in a 99.71 ± 0.01% dense part. As-printed interfaces resulted in a denser part (99.82 ± 0.02%) at the expense of dimensional accuracy. The hardness of the parts with as-printed and machined interfaces was 196 ± 0.37 HV and 192 ± 0.40 HV, respectively, compared to 156 ± 1.4 HV for the substrate. Depositing powder alongside or on top of wire sections resulted in interfaces with a hardness of 217 ± 2.2 HV, compared to 185 ± 3.4 HV for the wire-powder interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Formation of functionally graded steel by laser powder bed fusion via in-situ carbon doping

Additive Manufacturing (AM) enables functional integration by combining multiple components into a single part to shorten assembly time, reduce weight, and improve performance. Laser Powder Bed Fusion (LPBF) is an important AM method due to excellent spatial resolution, surface finish, and material properties without the need for extensive post-processing. Functional integration could be enhanced by spatial tuning of properties, but LPBF cannot readily vary material composition. Here, this paper addresses a method to add spatial composition control by printing small quantities of dopants via liquid carrier prior to laser fusion. The impact of carbon black suspension added to select regions of a Stainless Steel 316 L powder bed on melt pool dimension, hardness, and porosity is reported. The distribution of the carbon between the doped and plain layers and the resulting spatial variation in hardness is measured. Optical microscopy and composition analysis show that the carbon dispersed uniformly within the layer of deposition and diffused as little as 50 μm in the build direction. Keyhole conditions dramatically increase the inter-layer transport of the dopant. The added carbon increased hardness by >50 %. Porosity increased in doped regions but remained below 1.5 % for the best processing parameters. These results demonstrate that the composition of LPBF parts could be controlled in 3-dimensions using a dopant that is soluble in the melt pool. Additional work will be required to evaluate different dopant materials and optimize processing conditions for full density, but microalloying with soluble dopants appears to be a plausible solution to enhance functional integration with LPBF.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Joining Light Metals with Polymer Composites Through Metal Overcasting

This work investigates a unique technique to join aluminum (Al) and magnesium (Mg) alloys to carbon fiber reinforced polymer (CFRP) composites without the use of adhesives or mechanical fasteners. The joints were made using an overcasting technique where the molten alloys were cast around the polymer composites using high pressure die casting method. Rapid cooling during casting allowed the composite to be embedded inside the cast metal without causing any gross damage to the former even though the molten metal temperature exceeded the melting point of the composite matrix by several 100’s of deg. C. The metal/composite interface was examined using optical microscopy and x-ray imaging and the joint strength was examined through tensile testing. Although evidence of polymer melting was evident in the x-ray images, the embedded section of the composite coupons retained their overall shape and integrity. Preliminary tension tests on Al/CFRP composites showed strength degradation of the CFRP and it failed near the metal/CFRP interface (outside the joint). Strength degradation in the CFRP suggests that the overcasting process needs further optimization to minimize thermal excursion in the CFRP. Nevertheless, the overcasting process shows great promise as a unique joining technique with application in fabricating light-weight structures for automotive and transportation industries.

overcasting, Casting, Mg Castings, Al Casting, Joi↗
DOE OSTI2021

A Comparative Study on the Effect of Zr, Sn, and Ti on the Crystallization Behavior of Nepheline Glass

In alkali aluminosilicate glasses, additions of 4+ cations like Zr and Ti are often added to promote crystallization. In this study, Zr, Ti, or Sn are progressively substituted for Si in nepheline (NaAlSiO4) glass to determine their impact on the crystallization behavior. For glasses homogeneous on quenching, up to NaAlZr0.075Si0.925O4, NaAlSn0.100Si0.900O4, and NaAlTi0.300Si0.700O4, respectively, crystallization temperatures were investigated by thermal analysis. A subset of compositions was subjected to additional thermal analysis, varying heating rate and particle size, to investigate the subtleties of crystallization behavior. Subsequent heat treatment of glass powders was performed to maximize crystallization, and glass-ceramic microstructure was assessed by optical microscopy and electron microprobe, while crystalline phases were determined by X-ray diffraction. In all cases the major crystalline phase was orthorhombic carnegieite, which accommodated Ti in its structure but not Zr or Sn, and excess 4+ cations formed MO2, i.e., brookite, baddeleyite, and cassiterite, respectively.

Nienhuis-Marcial, Emily T.↗
DOE OSTI2015

Deformation localization and dislocation channel dynamics in neutron-irradiated austenitic stainless steels

We investigated dynamics of deformation localization and dislocation channel formation in situ in a neutron irradiated AISI 304 austenitic stainless steel and a model 304-based austenitic alloy by combining several analytical techniques including optic microscopy and laser confocal microscopy, scanning electron microscopy, electron backscatter diffraction and transmission electron microscopy. Channel formation was observed at 70% of the formal tensile yield stress for both alloys. It was shown that triple junction points do not always serve as a source of dislocation channels; at stress levels below the yield stress, channels often formed near the middle of the grain boundary. For a single grain, the role of elastic stiffness value (Young modulus) in the channel formation was analyzed; it was shown that in the irradiated 304 steels the initial channels appeared in soft grains with a high Schmid factor located near stiff grains with high elastic stiffness. Moreover, the spatial organization of channels in a single grain was analyzed; it was shown that secondary channels operating in the same slip plane as primary channels often appeared at the middle or at one third of the way between primary channels. The twinning nature of dislocation channels was analyzed for grains of different orientation using TEM. Finally, it was shown that in the AISI 304 steel, channels were twin-free in grains oriented close to [001] and [101] of standard unit triangle; [111]-grains and grains oriented close to Schmid factor maximum contained deformation twins.

36 MATERIALS SCIENCE↗