Search NASA⌕ Search

SEARCH · Search NASA

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Experimental fatigue life investigation of cylindrical thrust chambers

Twenty-two cylindrical test sections of a cylindrical rocket thrust chamber were fabricated and 21 of them were cycled to failure to explore the failure mechanisms, determine the effects of wall temperature on cyclic life, and to rank the material life characteristics for comparison with results from isothermal tests of 12 alloys at 538 C. Cylinder liners were fabricated from OFHC copper, Amzirc, and NAR1loy-Z. Tests were conducted at a chamber pressure of 4.14 MW/sq m using hydrogen-oxygen propellants at an oxidant-fuel ratio of 6.0, which resulted in an average throat heat flux of 54 MW/sq m. The cylinders were cooled with liquid hydrogen at an average rate of 0.91 Kg/sec. All failures were characterized by a thinning of the cooling channel wall at the centerline and eventual failure by tensile rupture. Cyclic life rankings of the materials based on temperature do not agree with published rankings based on uniaxial, isothermal strain tests.

Quentmeyer, R. J.↗
NASA NTRS1977

Water vapor diffusion membrane development

An application of the water vapor diffusion technique is examined whereby the permeated water vapor is vented to space vacuum to alleviate on-board waste storage and provide supplemental cooling. The work reported herein deals primarily with the vapor diffusion-heat rejection (VD-HR) as it applies to the Space Shuttle. A stack configuration was selected, designed and fabricated. An asymmetric cellulose acetate membrane, used in reverse osmosis application was selected and a special spacer was designed to enhance mixing and promote mass transfer. A skid-mount unit was assembled from components used in the bench unit although no attempt was made to render it flight-suitable. The operating conditions of the VD-HR were examined and defined and a 60-day continuous test was carried out. The membranes performed very well throughout the test; no membrane rupture and no unusual flux decay was observed. In addition, a tentative design for a flight-suitable VD-HR unit was made.

Tan, M. K.↗
NASA NTRS1977

Effects of heat treating PM Rene' 95 slightly below the gamma' solvus

An investigation was performed on as-hot-isostatically-pressed (As-HIP) Rene' 95 to obtain additional information on the variation of the amount of gamma prime with solutioning temperatures near the gamma prime solvus temperature and the resulting effects on tensile and stress rupture strength of As-HIP Rene' 95. The amount of gamma prime phase was found to increase at a rate of about 0.5% per degree Celsius as the temperature decreased from the solvus temperature to about 50 C below the gamma prime solvus temperature. The change in the amount of gamma prime phase with decreasing solutioning temperature was observed to be primarily associated with decreasing solubilities of Al+Ti+Nb and increasing solubility of Cr in the gamma phase.

Dreshfield, R. L.↗
NASA NTRS1977

Ductility normalized-strainrange partitioning life relations for creep-fatigue life predictions

Procedures based on Strainrange Partitioning (SRP) are presented for estimating the effects of environment and other influences on the high temperature, low cycle, creep fatigue resistance of alloys. It is proposed that the plastic and creep, ductilities determined from conventional tensile and creep rupture tests conducted in the environment of interest be used in a set of ductility normalized equations for making a first order approximation of the four SRP inelastic strainrange life relations. Different levels of sophistication in the application of the procedures are presented by means of illustrative examples with several high temperature alloys. Predictions of cyclic lives generally agree with observed lives within factors of three.

Halford, G. R.↗
NASA NTRS1977

Effects of high temperature and e-beam irradiation on the stability of refractory thin films

Refractory thin films of Al2O3, ZrO2, MgO, ThO2, and BN have been investigated in situ in an UHV transmission electron microscope. The electron transparent refractory films were prepared by electron-beam evaporation, anodization, RF sputtering, and thinning of bulk crystal materials. The study concentrates on monitoring the thermal and mechanical stability of the films, phase and structural changes, and electron irradiation effects as a function of film-preparation conditions. With increasing temperatures, five different crystallographic phases were observed for both anodized and electron-beam-evaporated alumina films. Zirconia films exhibited two phase transitions upon heating to 1200 C and electron-irradiation-induced crystallization of ZrO2 even at room temperature. MgO, ThO2, and BN films did not undergo any noticeable phase transformation but ruptured due to sintering below 1200 C.

Lee, E. H.↗
NASA NTRS1977

Crack propagation and arrest in pressurized containers

The problem of crack propagation and arrest in a finite volume cylindrical container filled with pressurized gas is considered. It is assumed that the cylinder contains a symmetrically located longitudinal part-through crack with a relatively small net ligament. The net ligament suddenly ruptures initiating the process of fracture propagation and depressurization in the cylinder. The problem is formulated by making two major assumptions, namely, that the shell problem is quasi-static and the gas dynamics problem is one-dimensional. The problem is reduced to a proper initial value problem by introducing a dynamic fracture criterion which relates the crack acceleration to the difference between a load factor and the corresponding strength parameter. The main results are demonstrated by considering two examples, an aluminum cylinder which may behave in a quasi-brittle manner, and a steel cylinder which undergoes ductile fracture. The results indicate that generally in gas-filled cylinders fracture arrest is not possible unless the material behaves in a ductile manner and the container is relatively long.

Erdogan, F.↗
NASA NTRS1977

Understanding the Larson-Miller parameter

The Larson-Miller (L-M) method of extrapolating stress rupture and creep results is based on the contention that the absolute temperature-compensated time function should have a unique value for a given material. This value should depend only on the applied stress level. The L-M method has been found satisfactory in the case of many steels and superalloys. The derivation of the L-M relation is discussed, taking into account a power law creep relationship considered by Dorn (1965) and Barrett et al. (1964), a correlation expression reported by Garofalo et al. (1961), and relations concerning the constant C. Attention is given to a verification of the validity of the considered derivation with the aid of suitable materials.

Furillo, F. T.↗
NASA NTRS1976

Hot environment effects on alloy mechanical properties

Prolonged high temperature performance of structural alloys requires joint attention to both corrosion and mechanical properties, and to their possible interactions. In this interpretive review paper, we provide a systematic compaction of theories and key observations on corrosion-mechanical properties interactions, from early single crystal work in the 1930s to recent studies on superalloys in nonoxidizing, oxidizing and hot corrosive environments. Particular attention is paid to environmental effects on creep, stress rupture and fatigue properties.

Davidson, J. M.↗
NASA NTRS1978

Temperature distributions and thermal stresses in a graded zirconia/metal gas path seal system for aircraft gas turbine engines

A ceramic/metallic aircraft gas turbine outer gas path seal designed for improved engine performance was studied. Transient temperature and stress profiles in a test seal geometry were determined by numerical analysis. During a simulated engine deceleration cycle from sea-level takeoff to idle conditions, the maximum seal temperature occurred below the seal surface, therefore the top layer of the seal was probably subjected to tensile stresses exceeding the modulus of rupture. In the stress analysis both two- and three-dimensional finite element computer programs were used. Predicted trends of the simpler and more easily usable two-dimensional element programs were borne out by the three-dimensional finite element program results.

Taylor, C. M.↗
NASA NTRS1977

The effect of microstructure and strength on the fracture toughness of an 18 Ni, 300 grade maraging steel

Fractography and metallographic sectioning were used to investigate the influence of microstructure and strength on the fracture toughness (KIc) and fracture mechanism of an 18 Ni, 300 grade maraging steel. Increased yield strength from 1442 to 2070 MN/m squared through precipitation hardening results in a KIc loss from 143 to 55 MN/m superscript 3/2. Ti (C,N) Ti2S, and TiC inclusions in sizes from 1 to 8, 1 to 15, and 0.1 to 2 microns respectively serve as sites for void nucleation and lead to fracture by the dimpled rupture process in all strength levels considered. TiC nucleated dimples occupy more than half the fracture in all conditions. Void nucleation rate and resultant number of dimples per unit area of fracture increase with increasing yield strength. Average dimple size decreases with increasing strength and/or overaging which follows from the decreasing amount of stable void growth measured by sectioning tensile specimens. Void growth is assisted by crack branching along a path of TiC inclusions. Coalescence occurs in the highest strength materials by a combination of TiC void nucleation and premature separation at strengthening precipitates.

Psioda, J. A.↗
NASA NTRS1977

Laser-zone growth in a Ribbon-To-Ribbon, RTR, process silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

A ribbon-to-ribbon process was used for routine growth of samples for analysis and fabrication into solar cells. One lot of solar cells was completely evaluated: ribbon solar cell efficiencies averaged 9.23% with a highest efficiency of 11.7%. Spherical reflectors have demonstrated significant improvements in laser silicon coupling efficiencies. Material analyses were performed including silicon photovoltage and open circuit photovoltage diffusion length measurements, crystal morphology studies, modulus of rupture measurements, and annealing/gettering studies. An initial economic analysis was performed indicating that ribbon-to-ribbon add-on costs of $.10/watt might be expected in the early 1980's.

Gurtler, R. W.↗
NASA NTRS1978

Low cycle fatigue in turbines

Behavior of certain components at low-cycle fatigue is a parameter related to the conditions of use of turbines, to the technology of engine production and to the precision of its regulation. The laboratory takes this into account using data from sophisticated tests and rigorous analyses. The production plan includes careful examination of possible causes of premature rupture. This parameter has motivated the metallurgy industry to develop new materials and new technology.

Brun, M.↗
NASA NTRS1978

Different aspects of low-cycle fatigue

The experimental and theoretical knowledge in this field is presented. The different relations which correlate the number of cyles to rupture with strain or strain-energy are given. The application of low-cycle fatigue concepts to the crack initiation and crack propagation are briefly studied.

Bathias, C.↗
NASA NTRS1977

Strength enhancement process for prealloyed powder superalloys

A technique involving superplastic processing and high pressure autoclaving was applied to a nickel base prealloyed powder alloy. Tensile strengths as high as 2865 MN/sq m at 480 C were obtained with as-superplastically deformed material. Appropriate treatments yielding materials with high temperature tensile and stress rupture strengths were also devised.

Waters, W. J.↗
NASA NTRS1977

Pressureless sintered beta prime-Si3N4 solid solution: Fabrication, microstructure, and strength

Si3N4, AlN, and Al2O3 were used as basic constituents in a study of the pressureless sintering of beta prime-Si3N4 solid solution as a function of temperature. Y2O3-SiO2 additions were used to promote liquid-phase sintering. The sintered specimens were characterized with respect to density, microstructure, strength, oxidation, and thermal shock resistance. Density greater than 98 percent of theoretical was achieved by pressureless sintering at 1750 C. The microstructure consisted essentially of fine-grained beta prime-Si3N4 solid solution as the major phase. Modulus of rupture strengths up to 483 MPa were achieved at moderate temperature (1000 C), but decreased to 228 MPa at 1380 C. This substantial strength loss was attributed to a glassy grain boundary phase formed during cooling from the sintering temperature. The best oxidation resistance was exhibited by a composition containing 3 mol % Y2O3-SiO2 additives. Water quench thermal shock resistance was equivalent to that of reaction sintered silicon nitride but lower than hot-pressed silicon nitride.

Dutta, S.↗
NASA NTRS1978

Thermomechanical processing of HAYNES alloy No. 188 sheet to improve creep strength

Improvements in the low strain creep strength of HAYNES alloy No. 188 thin gauge sheet by means of thermomechanical processing were developed. Processing methods designed to develop a sheet with strong crystallographic texture after recrystallization and to optimize grain size were principally studied. The effects of thickness-to-grain diameter ratio and prestrain on low strain creep strength were also briefly examined. Results indicate that the most significant improvements were obtained in the sheets having a strong crystallographic texture. The low strain creep strength of the textured sheets was observed to be superior to that of standard production sheets in the 922 K to 1255 K temperature range. Tensile, stress rupture, fabricability, and surface stability properties of the experimental sheets were also measured and compared to property values reported for the baseline production sheets.

Klarstrom, D. L.↗
NASA NTRS1977

Particle motion on Mars inferred from the Viking lander cameras

Data from Viking lander cameras indicate fine particle mobility on the surface of Mars such as: probable ventifacts, rock-associated raised streaks, and particulate drifts. Peak wind directions inferred from Chryse and Utopia are roughly equal, and are consistant with those inferred by orbiter photography. A 24 deg systematic offset between: (1) the direction of rock-associated streaks in the Viking I landing site, and (2) Mariner 9 and Viking observations of crater-associated streaks is consistant with a Coriolis acceleration of particles entrained by high-velocity winds during the production of crater-associated streaks. It is suggested that if a large fraction of collision impact energy goes into deformation, strain, and rupture, a preferential destruction of the most easily saltated grains and a depletion of 15-micron diameter grains will be observed. Investigations of particulates dumped on the landing grid suggest that major saltation events took place between sols 96 and 207, caused by winds of greater than 50 meters/sec normalized to the top of the boundary layer.

Sagan, C.↗
NASA NTRS1977

Preliminary development of a fundamental analysis model for crack growth in a fiber reinforced composite material

A mathematical model for the strength of fiber reinforced composites containing specific flaws is described. The approach is to embed a local heterogeneous region surrounding the crack tip in an anisotropic elastic continuum. By consideration of the individual failure events activated near the flaw tip, a strength prediction can be made from basic properties of the composite constituents. Computations for arbitrary flaw size and orientation have been performed for unidirectional composites with linear elastic-brittle constituent behavior. The mechanical properties were those of graphite epoxy. With the rupture properties arbitrarily varied to test the capability of the model to reflect real fracture modes in fiber composites, it is shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting all can occur during gradually increasing load prior to catastrophic fracture. Qualitative comparisons with experimental results on edge-notched unidirectional graphite epoxy specimens have also been made.

Kanninen, M. F.↗