SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Signal transmission disturbances caused by presence of rocket exhaust plasmas in propagation medium between ground station and rocket powered vehicle
Printouts and graphs of rocket winds, radiosonde observations and/or thermodynamics of February 1966 firings of Meteorological Rocket Network
Nuclear rocket propulsion development, noting nuclear rocket engine test program
A flight investigation of two Nike-Deacon (DAN) two-stage solid-propellant rocket vehicles indicated satisfactory performance may be expected from the DAN meteorological sounding rocket. Peak altitudes of 356,000 and 350,000 feet, respectively, were recorded for the two flight tests when both vehicles were launched from sea level at an elevation angle of 75 degrees. Performance calculations based on flight-test results show that altitudes between 358,000 feet and 487,000 feet may be attained with payloads varying between 60 pounds and 10 pounds.
An experimental investigation of high-frequency combustion oscillations (screaming) was conducted with a 100-pound-thrust acid-hydrocarbon rocket engine and a 500-pound-thrust oxygen-fuel rocket engine. The oscillation frequencies could be correlated as a linear function of the parameter C/L, where C is the experimentally measured characteristic velocity and L is the combustion-chamber length. The tendency of the engines to scream increased as chamber length was increased. With engine configurations that normally had a low efficiency, screaming resulted in increased performance; at the same time, a five to tenfold increase in heat-transfer rate occurred. It was possible, however, to achieve good performance without screaming.
Most experts agree that single-stage-to-orbit (SSTO) rockets would become feasible if more advanced technologies were available to reduce the vehicle dry weight, increase propulsion system performance, or both. However, these technologies are usually judged to be very ambitious and very far off. This notion persists despite major advances in technology and vehicle design in the past decade. There appears to be four major misperceptions about SSTOs, regarding their mass fraction, their presumed inadequate performance margin, their supposedly small payloads, and their extreme sensitivity to unanticipated vehicle weight growth. These misperceptions can be dispelled for SSTO rockets using advanced technologies that could be matured and demonstrated in the near term. These include a graphite-composite primary structure, graphite-composite and Al-Li propellant tanks with integral reusable thermal protection, long-life tripropellant or LOX-hydrogen engines, and several technologies related to operational effectiveness, including vehicle health monitoring, autonomous avionics/flight control, and operable launch and ground handling systems.
My summer was spent working as an intern at Kennedy Space Center in the Propulsion Avionics Branch of the NASA Engineering Directorate Avionics Division. The work that I was involved with was part of Rocket University's Project Neo, a small scale liquid rocket engine test bed. I began by learning about the layout of Neo in order to more fully understand what was required of me. I then developed software in LabView to gather and scale data from two flowmeters and integrated that code into the main control software. Next, I developed more LabView code to control an igniter circuit and integrated that into the main software, as well. Throughout the internship, I performed work that mechanics and technicians would do in order to maintain and assemble the engine.
In high energy solar astrophysics, imaging hard X-rays by direct focusing offers higher dynamic range and greater sensitivity compared to past techniques that used indirect imaging. The Focusing Optics X-ray Solar Imager (FOXSI) is a sounding rocket payload which uses seven sets of nested Wolter-I figured mirrors that, together with seven high-sensitivity semiconductor detectors, observes the Sun in hard X-rays by direct focusing. The FOXSI rocket has successfully flown twice and is funded to fly a third time in Summer 2018. The Wolter-I geometry consists of two consecutive mirrors, one paraboloid, and one hyperboloid, that reflect photons at grazing angles. Correctly focused X-rays reflect twice, once per mirror segment. For extended sources, like the Sun, off-axis photons at certain incident angles can reflect on only one mirror and still reach the focal plane, generating a pattern of single-bounce photons that can limit the sensitivity of the observation of faint focused X-rays. Understanding and cutting down the singly reflected rays on the FOXSI optics will maximize the instrument's sensitivity of the faintest solar sources for future flights. We present an analysis of the FOXSI singly reflected rays based on ray-tracing simulations, as well as the effectiveness of different physical strategies to reduce them.
A series of experiments was performed to determine the feasibility of using the Background Oriented Schlieren, BOS, flow visualization technique to image a simulated, small, rocket engine, plume under altitude test conditions. Testing was performed at the NASA Glenn Research Centers Altitude Combustion Stand, ACS, using nitrogen as the exhaust gas simulant. Due to limited optical access to the facility test capsule, all of the hardware required to conduct the BOS were located inside the vacuum chamber. During the test series 26 runs were performed using two different nozzle configurations with pressures in the test capsule around 0.3 psia. No problems were encountered during the test series resulting from the optical hardware being located in the test capsule and acceptable resolution images were captured. The test campaign demonstrated the ability of using the BOS technique for small, rocket engine, plume flow visualization during altitude testing.
Micro-X is a sounding rocket-borne instrument that uses a microcalorimeter array to perform high-resolution X-ray spectroscopy. This instrument flew for the first time on July 22nd, 2018, from the White Sands Missile Range, USA. This flight marks the first successful operation of a transition-edge sensor array and its time-division multiplexing readout system in space. This launch was dedicated to the observation of the supernova remnant Cassiopeia A. A failure in the attitude control system prevented the rocket from pointing and led to no time on target. The onboard calibration source provided X-rays in flight, and it is used to compare detector performance during preflight integration, flight, and after the successful post-flight recovery. This calibration data demonstrate the capabilities of the detector in a space environment as well as its potential for future flight.
Carbon-carbon (C-C) composite and ceramic matrix composite (CMC) nozzle extensions are being considered and developed for use with a variety of cryogenic liquid rocket engine systems. Some of the potential applications include in-space, lunar lander, and launch vehicle upper stage propulsion systems. Composite material systems of interest include C-C and carbon/silicon-carbide (C-SiC) composites, as well as modified versions of such composites (coatings, mixed matrices, oxidation inhibitors, etc.). Nozzle extension materials and fabrication methods under development by industry support both National Aeronautics and Space Administration (NASA) and Department of Defense (DOD) requirements, as well as those of the broader Commercial Space industry. Marshall Space Flight Center (MSFC) efforts are aimed at both (a) assisting industry with the development of composite nozzle extensions for cryogenic liquid rocket engines, and (b) developing and demonstrating capabilities for characterizing, testing, and qualifying such nozzle extensions. Results of recent MSFC nozzle-extension characterization efforts and engine firing demonstrations will be presented.
Our team is working on building and calibrating the FURST sounding rocket, with an expected launch in mid-2023. The goal is to image the most complete and highest resolution UV spectra to date. To do this, preciseradiometric and wavelength calibration techniques have been developed. We describe below our model of O2 atmospheric absorption and couple that with simulated FURST images. With a high-enough SNR, we canestimate our ability to use absorption peaks for calibration, or for back-calculating atmospheric properties. If data is available, this method could be applied to older sounding rocket data to find hidden science.
Our team is working on building and calibrating the FURST sounding rocket, with an expected launch in mid-2023. The goal is to image the most complete and highest resolution UV spectra to date. To do this, precise radiometric and wavelength calibration techniques have been developed. We describe below our model of O2 atmospheric absorption and couple that with simulated FURST images. With a high-enough SNR, we can estimate our ability to use absorption peaks for calibration, or for back-calculating atmospheric properties. If data is available, this method could be applied to older sounding rocket data to find hidden science.
Upper stage rocket engines are optimized for operation at the edge of space. Ground testing often requires simulation of high-altitude environments to prevent damage from off-design operation. Passive supersonic diffusers are an effective means of establishing the partial vacuum needed around the nozzle exit. The low cost of diffusers relative to active vacuum sources (ejectors, pumps, etc.) provides a perpetual incentive to improve their performance and expand the envelope of passively testable engines. Second-throat diffusers have been the de facto standard for rocket testing since the 1950s, and numerous studies have focused on parametric optimization of the topology. Yet, even the best second-throat designs may require more driving pressure than an upper stage engine can provide. To overcome conventional limits, engineers at NASA’s Stennis Space Center (SSC) adapted an obscure cold-flow diffuser topology to the extremes of immersion in supersonic combustion products. Aerodynamic experimentation was conducted at SSC’s E-3 test stand to quantify the performance of prototypical hot-fire spike diffuser hardware and enable direct comparison to prior states of the art. A LO X /GH 2 thruster was contoured to approximate the regeneratively-cooled nozzle of an upper-stage engine and fired into 28 downstream diffuser configurations: 16 second-throat, 2 centerbody, and 10 spike. Temperature and pressure were recorded along the test article walls for a range of chamber pressures spanning 3.5 - 5.0 MPa. The second-throat configurations with the lowest start and unstart pressure ratios were shown to outperform equivalent systems in literature and taken as baselines for evaluation of advanced diffuser performance. Compared to these exemplars, centerbody diffusers decreased start pressure ratio by 11% but increased unstart pressure ratio by 15%. Spike diffusers reduced start and unstart pressure ratios by 24% and 9%, respectively.
Solid rocket motor internal insulations are facing serious issues with obsolescence of constituents and the need for improved performance. The design community is at a unique point with a large number of rocket motors requiring reformulation of insulation or design upgrades at the same time. Unfortunately, performance data related to component choice is not generally available to aid development. A study of insulation component materials, conducted at Marshall Space Flight Center over the last four years, used designed experiments to understand the contribution of each material to the performance of a formulation. This report covers work with Nitrile Butadiene Rubber (NBR) based formulations. In-house compounding provided modified formulations allowing for isolation of both individual and synergistic effects. All formulas were tested for mechanical, thermal and producibility properties to evaluate performance. This presentation will describe the methodology for, and results from, identifying the individual and combined effects of components used in our formulations. Specific properties investigated include, rheology, cure characteristics, density, tensile strength, along with erosion/ablation under various heat loads and flame chemistries. Scale up of several formulas from lab to production size batches was accomplished. We will discuss troubleshooting problems of scale and the new set of designed experiments with Ethylene Propylene Diene Monomer (EPDM) based formulations.
Subscale rocket testing offers a chance to examine exhaust plume behavior and prove out auxiliary systems early in a development cycle, when the cost of design iteration remains low. Despite the utility of experimentation, perfect similitude between a rocket engine and a scaled model is unobtainable; choices must be made to prioritize the reproduction of certain parameters at the expense of others. The experimentalist’s toolkit contains a variety of techniques to achieve this selective similarity. Determination of the appropriate tool is dependent on a test series’ specific objectives, facility limitations, and financial considerations. Preservation of full nozzle geometry is crucial if its internal flow is of interest. However, subscale thrusters often serve as a simple plume source in the evaluation of adjacent phenomena: vehicle base pressures, retropropulsive flows, supersonic diffuser performance, refractory erosion, deflector cooling, impingement shock structures, etc. In such cases, it may be permissible to rework the nozzle geometry to compensate for discrepancies in subscale propellant pressure, temperature, or chemical composition. Thrust, pressure, Mach number, heat flux, and myriad other parameters can be used to ground the altered designs. Subscale diffuser testing at the full chamber pressure of flight hardware is occasionally infeasible. It is hypothesized that, absent a means of backpressure reduction, comparable performance may be obtained for a prescribed motive fluid by maintaining scaled engine mass flow and nozzle exit geometry at the expense of throat geometry, exit pressure, and Mach number. The present work offers discrete empirical support for this mass-flow-based approach to contour modification.
NASA has been developing additive manufacturing (AM) for various technical and programmatic advantages for complex rocket engine and aerospace components. This maturation has focused on various AM processes, new alloys, characterizing material properties, developing standards, producing demonstrator parts, and integrating AM hardware in liquid rocket engines through test-fail-fix cycles, as well as application and dissemination of lessons learned of the AM lifecycle. The importance of proper AM processing was made evident in the failure of a Laser Powder Bed Fusion (L-PBF) copper-alloy combustion chamber during a hot-fire test due to a degraded material quality. The hot-fire test aimed to demonstrate high duty cycle under a risk-tolerant development project, where consequences of component failure would be minimal. However, the unintentional component failure emphasized the necessity of robust material characterization and rigorous process control procedures for the safe use of AM components in critical applications. This presentation provides an overview of the development failure, a discussion on the evaluation of the failed chamber and supplemental chambers produced at the same time, a representative material samples that included intentional build witness lines, and a summary of the key results and recommendations from the evaluations. NASA continues to approach AM processes and designs with a level of risk and acceptance of failures that is appropriate for the project objectives, with the overall goal of safe implementation of AM technology and transferring AM technology into commercial space applications. This presentation with provide critical awareness to the community lessons learned on proper implementation of AM.
Additive manufacturing (AM) has revolutionized component design for liquid rocket engines by offering rapid manufacturing capabilities. This has led to significant opportunities for development and flight programs in the propulsion industry, resulting in cost and schedule savings, as well as performance improvements through new designs and alloy development. A noteworthy example is the GRX-810 oxide dispersion strengthened (ODS) alloy, which was specifically developed for extreme temperatures. This Ni-Co-Cr based alloy was created using integrated computational materials engineering (ICME) techniques to focus on a new class of materials with exceptional temperature and oxidation-resistant properties. The GRX-810 alloy utilizes AM processes to incorporate nano-scale yttria particles throughout its microstructure, resulting in remarkable enhancements. Compared to traditional Nickel-based superalloys, the GRX-810 alloy offers a two-fold increase in tensile strength, 1,000-fold better creep properties, and two-fold improvement in oxidation resistance. NASA successfully demonstrated the development and manufacturing of components using the GRX-810 alloy through laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Extensive efforts were made to model, evaluate metallurgical properties, develop heat treatment processes, characterize the microstructure, and determine mechanical properties. The GRX-810 alloy was specifically designed for aerospace applications, including liquid rocket engine injectors, preburners, turbines, and hot-section components, capable of withstanding temperatures up to 1,100 °C. The objective of this alloy development is to bridge the temperature gap between traditional Nickel-based superalloys and refractory alloys. This paper provides a comprehensive comparison of the GRX-810 alloy with other aerospace alloys, discussing its microstructure, mechanical properties, processing advancements, component development, and hot-fire testing results. The ultimate goal of this development was to elevate the Technology Readiness Level (TRL) of the GRX-810 alloy, enabling its integration into NASA and commercial aerospace applications.