Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Three dimensional finite element analysis of damage accumulation in composite laminate

A three dimensional finite-element computer program has been developed to analyze layered fiber-reinforced composite laminate. This program is capable of: (1) calculating the detailed stress distribution, (2) identifying the damage zone and mode of failure, (3) analyzing the damage accumulation, and (4) determining the ultimate strength of the composite laminate.

Lee, J. D.↗

Design and development of a ceramic radial turbine for the AGT101

An acceptable and feasible ceramic turbine wheel design has been achieved, and the relevant temperature, stress, and success probability analyses are discussed. The design is described, the materials selection presented, and the engine cycle conditions analysis parameters shown. Measured MOR four-point strengths are indicated for room and elevated temperatures, and engine conditions are analyzed for various cycle states, materials, power states, turbine inlet temperatures, and speeds. An advanced gas turbine ceramic turbine rotor thermal and stress model is developed, and cumulative probability of survival is shown for first and third-year properties of SiC and Si3N4 rotors under different operating conditions, computed for both blade and hub regions. Temperature and stress distributions for steady-state and worst-case shutdown transients are depicted.

Finger, D. G.↗

Analytical and experimental study of a standing torus with normal loads

Finite element analysis is applied to study the large deflection and stress of a thin-walled pressurized torus loaded by normal contact with a plane. Experimentally determined stresses are compared to those resulting from finite element analysis at various meridional and circumferential coordinates of the torus, including the footprint area. Circumferential strains compare favorably while meridional strains are higher in the finite element analysis, probably due to slippage of the boundary at the rim. The STAGS finite element computer program was used. The purpose of the study was to evaluate the various program options for structural loading, for material modeling, for stress analysis, and for grid refinement. The experimental model, a thin-walled rubber tube mounted on a steel cylindrical rim, provided measured results to compare with various analytical trade-offs. It was found that there was almost no difference in predicted deflections or stress distributions between linear and nonlinear material description. However, the difference between linear analysis and that of geometric nonlinearities utilizing incremental loading was marked.

Mack, M. J., Jr.↗

A time dependent theory of crazing behavior in polymers

The development of crazing is not only a function of stress, but also a function of time. Under a simple state of tension, a craze opening displacement is closely associated with the viscoelastic behavior of the original bulk polymer medium in which individual crazes initiate and develop. Within each craze region, molecular orientation takes place when conditions permit, and a new phase of rearranged molecules governs its local behavior. Based upon a time-dependent viscoelastic two-dimensional model, using a computer program the craze opening displacement field has been calculated, time-dependent craze length was also computed by taking into consideration the molecular orientation mechanism and large deformations in the craze region. Examples are given for simple viscoelastic media with simplified stress distributions. It is interesting to find out that the occurrence of crazing may be interpreted in terms of the stability or instability of the constitutive behavior of the bulk polymer.

Chern, S. S.↗

Contact between a rigid cylinder and an orthotropic beam under initial stress

The contact behavior between a smooth rigid cylinder and a simply-supported orthotropic beam under uniaxial initial stresses is studied. The displacements are computed by superposing Mindlin plate solution with the solution obtained from Biot's theory of incremental deformation. Finite Fourier transforms are used in solving the equations. The effects of orthotropy and initial stresses on the contact stress distribution are investigated. An indentation law is established from the numerical results.

Sun, C. T.↗

Mathematical modeling of damage in unidirectional composites

Extending the work of Goree and Gross (1979), solutions are given for a two-dimensional region of unidirectional fibers embedded in an elastic matrix whose initial flaw may take the form of a transverse notch, a rectangular cutout, or a circular hole. Subsequent flaw-induced damage is generated by remote stresses acting parallel to the fibers. For the case of such ductile matrix composites as boron/aluminum, present results indicate that both longitudinal matrix yielding and transverse notch extension must be included in order for the model to agree with experimental results. Little difference is found for the three types of initial damage considered. In all cases, the presence of additional damage changes the nature of stress distribution through the unbroken fibers.

Goree, J. G.↗

Dynamic behavior of an unsteady turbulent boundary layer

Experiments on an unsteady turbulent boundary layer are reported in which the upstream portion of the flow is steady (in the mean) and in the downstream region, the boundary layer sees a linearly decreasing free stream velocity. This velocity gradient oscillates in time, at frequencies ranging from zero to approximately the bursting frequency. For the small amplitude, the mean velocity and mean turbulence intensity profiles are unaffected by the oscillations. The amplitude of the periodic velocity component, although as much as 70 percent greater than that in the free stream for very low frequencies, becomes equal to that in the free stream at higher frequencies. At high frequencies, both the boundary layer thickness and the Reynolds stress distribution across the boundary layer become frozen. The behavior at higher amplitude is quite similar. At sufficiently high frequencies, the boundary layer thickness remains frozen at the mean value over the oscillation cycle, even though flow reverses near the wall during a part of the cycle. Previously announced in STAR as N81-28392

Parikh, P. G.↗

Analysis and acoustooptical measurements of bulk and surface acoustic wave fields

The development of multielement ultrasonic transducers having full field amplitude and phase control is discussed. In addition, the measurement of the surface particle displacement caused by an idealized impulse load on the surface, the three dimensional mapping of acoustic fields using optical scanning techniques, and the measurement of two dimensional stress distributions using embedded optical fiber sensors are addressed.

Claus, R. O.↗

Experimental studies on two dimensional shock boundary layer interactions

Experiments have been performed on the interaction of oblique shock waves with flat plate boundary layers in the 30.48 cm x 30.48 cm (1 ft. x 1 ft.) supersonic wind tunnel at NASA Lewis Research Center. High accuracy measurements of the plate surface static pressure and shear stress distributions as well as boundary layer velocity profiles were obtained through the interaction region. Documentation was also performed of the tunnel test section flow field and of the two-dimensionality of the interaction regions. The findings provide detailed description of two-dimensional interaction with initially laminar boundary layers over the Mach number range 2.0 to 4.0. Additional information with regard to interactions involving initially transitional boundary layers is presented over the Mach number range 2.0 to 3.0 and those for initially turbulent boundary layers at Mach 2.0. These experiments were directed toward providing well documented information of high accuracy useful as test cases for analytic and numerical calculations. Flow conditions encompassed a Reynolds number range of 4.72E6 to 2.95E7 per meter. The shock boundary layer interaction results were found to be generally in good agreement with the experimental work of previous authors both in terms of direct numerical comparison and in support of correlations establishing laminar separation characteristics.

Skebe, S. A.↗

Deformation measurements of composite multi-span beam shear specimens by Moire interferometry

Experimental analyses were performed for determination of in plane deformations and shear strains in unidirectional and quasi-isotropic graphite-epoxy beams. Forty-eight ply beams were subjected to 5 point and 3 point flexure. Whole field measurements were recorded at load levels from about 20% to more than 90% of failure loads. Contour maps of U and W displacement fields were obtained by moire interferometry, using reference gratings of 2400 lines/mm. Clearly defined fringes with fringe orders exceeding 1000 were obtained. Whole field contour maps of shear strains were obtained by a method developed for these tests. Various anomalous effects were detected in the displacement fields. Their analysis indicated excess shear strains in resin rich zones in regions of shear tractions; free edge shear strains in quasi-isotropic specimens in regions of normal stresses; and shear stresses associated with cyclic shear compliances of quasi-isotropic plies in regions of shear tractions. Their contributions could occur independently or in superposition. Qualitative analyses addressed questions of relaxation; influence of contact stress distribution; specimen failure; effect of specimen overhang; nonlinearity; and qualities of 5 and 3 point flexure tests.

Post, D.↗

Stress studies in EFG

Electrical characterization of defects induced in FZ and CZ silicon stress in four-point bending above 1200 C was started. Techniques to study electrical activity that will permit correlation of defect activity with diffusion length and with room and low temperature EBIC are being developed. Preliminary characterization of defects in ribbon grown at very low speeds of less than 1 cm/min shows that the dislocation density is very low over significant regions of cross section, while regions of high dislocation density (approx. 5 x 10(6)/cm(2)) occur in bands in a number of places. Addition measurements of stress distributions in EFG material were obtained at the University of Illinois using shadow-Moire interferometry.

Source record↗

Reliability of structural brittle materials

Traditionally, the use of brittle materials has been avoided in demanding structural applications because of their unreliability. They have been used however, due to other desirable properties, in nonstructural applications or where the mechanical load is minimal. The most common method utilized today for the design approach of brittle materials is the probabilistic, which takes into consideration the flaw and stress distribution within the brittle material. It does not take into consideration the fracture mechanics effect of strength degradation while aging under a mechanical load. This project will combine the two methods, probabilistic and fracture mechanics, into a more reliable design method for brittle materials.

Hall, W. B.↗

Learjet Model 55 Wing Analysis with Landing Loads

The NASTRAN analysis was used to determine the impact of new landing loads on the Learjet Model 55 wing. These new landing loads were the result of a performance improvement effort to increase the landing weight of the aircraft to 18,000 lbs. from 17,000 lbs. and extend the life of the tires and brakes by incorporating larger tires and heavy duty brakes. Landing loads for the original 17,000 lb. airplane landing configuration were applied to the full airplane NASTRAN model. The analytical results were correlated with the strain gage data from the original landing load static tests. The landing loads for the 18,000 lb. airplane were applied to the full airplane NASTRAN model, and a comparison was made with the original Model 55 data. The results of this comparison enable Learjet to determine the difference in stress distribution in the wing due to these two different sets of landing loads.

Boroughs, R. R.↗

Turbulent flow around a wing-fuselage type juncture

The flow over a 58-mm-thick uniform-thickness winglike body having a 1.5:1 elliptical leading edge and joined to a large flat plate (representing an aircraft fuselage) is characterized experimentally at freestream velocity 15 m/s, corresponding to Reynolds number 940,000/m, using hot-wire anemometry. The results are presented graphically, and it is found that the horseshoe vortex formed by the separation of the fuselage boundary layer ahead of the wing leading edge is effective in transporting turbulence and modifying the mean-flow characteristics and the turbulent-stress distribution. It is suggested that the slenderness ratio of the leading edge is the dominant factor affecting the strength and location of the vortex.

Kubendran, L. R.↗

Patterns of fracture and tidal stresses due to nonsynchronous rotation - Implications for fracturing on Europa

This study considers the global patterns of fracture that would result from nonsynchronous rotation of a tidally distorted planetary body. The incremental horizontal stresses in a thin elastic or viscous shell due to a small displacement of the axis of maximum tidal elongation are derived, and the resulting stress distributions are applied to interpret the observed pattern of fracture lineaments on Europa. The observed pattern of lineaments can be explained by nonsynchronous rotation if these features formed by tension fracturing and dike emplacement. Tension fracturing can occur for a small displacement of the tidal axis, so that the resulting lineaments may be consistent with other evidence suggesting a young age for the surface.

Helfenstein, P.↗

Smooth indentation of an initially stressed orthotropic beam

The contact behavior between a smooth rigid cylinder and a simply supported orthotropic beam under uniaxial initial stresses is studied. The displacements are computed by superposing Mindlin plate solution with the solution obtained from Biot's theory of incremental deformation. Finite Fourier transforms are used in solving the equations. A point matching technique is used to compute the contact stresses and the amount of indentation for a given contact length. The effects of orthotropy and initial stresses on the contact stress distribution are investigated. An indentation law is established from the numerical results.

Sun, C. T.↗

A beam theory for anisotropic materials

Beam theory plays an important role in structural analysis. The basic assumption is that initially plane sections remain plane after deformation, neglecting out-of-plane warpings. Predictions based on these assumptions are accurate for slender, solid, cross-sectional beams made out of isotropic materials. The beam theory derived in this paper from variational principles is based on the sole kinematic assumption that each section is infinitely rigid in its own plane, but free to warp out of plane. After a short review of the Bernoulli and Saint-Venant approaches to beam theory, a set of orthonormal eigenwarpings is derived. Improved solutions can be obtained by expanding the axial displacements or axial stress distribution in series of eigenwarpings and using energy principles to derive the governing equations. The improved Saint-Venant approach leads to fast converging solutions and accurate results are obtained considering only a few eigenwarping terms.

Bauchau, O. A.↗

Experimental and numerical investigation of supersonic flow through a square duct

Steady, developing, adiabatic supersonic flow in a square duct is investigated for an inlet Mach number of 3.91 and a unit Reynolds number of 1.8 x 10 to the 6th/m. The numerical results for laminar flow show that two secondary flow cells develop in the near vicinity of the corner which are centered about the corner bisector and distort the primary flow in this region. For turbulent flow, the experimental results indicate that two secondary flow cells also develop about the corner bisector, but are directed in an opposite sense to that observed for the laminar case. Numerical results based on the Baldwin-Lomax model show that this model is incapable of predicting turbulence-generated secondary flow cells. For a suitable choice of constants, the Gessner-Emery model is able to predict the strength of these cells, but is deficient with respect to predicting their positions in the flow and their distorting influence on the primary flow. These observations are based on comparisons made in this paper between predicted and measured total pressure contours, cross flow velocity profiles, and local wall shear stress distributions.

Davis, D. O.↗