Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stiff problems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Analysis of Delamination Growth from Matrix Cracks in Laminates Subjected to Bending Loads

A major source of delamination damage in laminated composite materials is from low-velocity impact. In thin composite laminates under point loads, matrix cracks develop first in the plies, and delaminations then grow from these cracks at the ply interfaces. The purpose of this study was to quantify the combined effects of bending and transverse shear loads on delamination initiation from matrix cracks. Graphite-epoxy laminates with 90 deg. plies on the outside were used to provide a two-dimensional simulation of the damage due to low-velocity impact. Three plate bending problems were considered: a 4-point bending, 3-point bending, and an end-clamped center-loaded plate. Under bending, a matrix crack will form on the tension side of the laminate, through the outer 90 deg. plies and parallel to the fibers. Delaminations will then grow in the interface between the cracked 90 deg. ply and the next adjacent ply. Laminate plate theory was used to derive simple equations relating the total strain energy release rate, G, associated with the delamination growth from a 90 deg. ply crack to the applied bending load and laminate stiffness properties. Three different lay-ups were tested and results compared. Test results verified that the delamination always formed at the interface between the cracked 90 deg. ply and the next adjacent ply. Calculated values for total G sub c from the analysis showed good agreement for all configurations. The analysis was able to predict the delamination onset load for the cases considered. The result indicated that the opening mode component (Mode I) for delamination growth from a matrix crack may be much larger than the component due to interlaminar shear (Mode II).

Murri, G. B.↗
NASA NTRS1985

Parametric study of stress-intensity factors in bonded composite stringer panels

Stress-intensity factors are determined for an infinite cracked orthotropic sheet adhesively bonded to an orthotropic stringer. Since the stringer is modeled as a semi-infinite sheet, the solution is most appropriate for a crack tip located near a stringer edge. Both adherends are treated as homogeneous, orthotropic media which are representative of many fiber-reinforced composite materials. The complex variable theory of elasticity was used to obtain a set of integral equations describing the problem. The integral equations are replaced by an equivalent sheet of algebraic equations, which are solved to obtain the shear stress distribution in the adhesive layer. From these adhesive stresses, the stress-intensity factors are found. A parametric study is conducted to determine the sensitivity of the system to material properties and specimen configuration. Unless the crack tip is very close to or under the stringer, the stress-intensity factor is approximately that of the unstiffened sheet. However, as the crack propagates beneath the stringer, the stress-intensity factor decreases significantly. Increasing the stringer stiffness or the adhesive stiffness also decreases the stress-intensity factor.

Bigelow, C. A.↗
NASA NTRS1988

Analysis of delamination growth from matrix cracks in laminates subjected to bending loads

A major source of delamination damage in laminated composite materials is from low-velocity impact. In thin composite laminates under point loads, matrix cracks develop first in the plies, and delaminations then grow from these cracks at the ply interfaces. The purpose of this study was to quantify the combined effects of bending and transverse shear loads on delamination initiation from matrix cracks. Graphite-epoxy laminates with 90 deg plies on the outside were used to provide a two-dimensional simulation of the damage due to low-velocity impact. Three plate bending problems were considered: a 4-point bending, 3-point bending, and an end-clamped center-loaded plate. Under bending, a matrix crack will form on the tension side of the laminate, through the outer 90 deg plies and parallel to the fibers. Delaminations will then grow in the interface between the cracked 90 deg ply and the next adjacent ply. Laminate plate theory was used to derive simple equations relating the total strain energy release rate, G, associated with the delamination growth from a 90 deg ply crack to the applied bending load and laminate stiffness properties. Three different lay-ups were tested and results compared. Test results verified that the delamination always formed at the interface between the cracked 90 deg ply and the next adjacent ply. Calculated values for total G sub c from the analysis showed good agreement for all configurations. The analysis was able to predict the delamination onset load for the cases considered. The result indicated that the opening mode component (Mode I) for delamination growth from a matrix crack may be much larger than the component due to interlaminar shear (Mode II).

Murri, Gretchen Bostaph↗
NASA NTRSDate not supplied

Aeroelastic Analysis of Highly Flexible Wings with Linearized Frequency-Domain Aerodynamics

Flutter analysis of configurations with geometric structural nonlinearities typically is done with time-domain analysis. The results from this process are computationally expensive and can yield cumbersome results that may be difficult to manage/interpret. Compared to time-domain methods, frequency-domain flutter analysis can provide additional insight into the characteristics of a flutter stability problem. By linearizing the aeroelastic problem about the nonlinear equilibrium state, this work applies frequency-domain aeroelastic analysis to the Pazy wing, the subject of the Large Deformation Working Group in the Aeroelastic Prediction Workshop. Generalized aerodynamic forces (GAFs) are computed with both a doublet-lattice method and a computational fluid dynamics solver at a range of reduced frequencies as well as a range of dynamic pressures to account for the dependence of the mode shapes on the nonlinear equilibrium state. These GAFs are used in a p-k flutter solver, which is modified to handle the dependence of the stiffness matrix and GAFs on the dynamic pressure.

Bret K Stanford↗
NASA NTRS1992

Optimal matrix approximants in structural identification

Problems of model correlation and system identification are central in the design, analysis, and control of large space structures. Of the numerous methods that have been proposed, many are based on finding minimal adjustments to a model matrix sufficient to introduce some desirable quality into that matrix. In this work, several of these methods are reviewed, placed in a modern framework, and linked to other previously known ideas in computational linear algebra and optimization. This new framework provides a point of departure for a number of new methods which are introduced here. Significant among these is a method for stiffness matrix adjustment which preserves the sparsity pattern of an original matrix, requires comparatively modest computational resources, and allows robust handling of noisy modal data. Numerical examples are included to illustrate the methods presented herein.

Beattie, C. A.↗
NASA NTRS2023

Prediction of Stiffness and Fatigue Lives of Polymer Matrix Composite Laminates Using Artificial Neural Networks

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, both Python and MATLAB-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been developed for both platforms. Results show that the both neural net types can provide an excellent estimate of initial stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminate. RNNs are better able to capture the shape of the fatigue curve of a laminate. This tool can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. The associated surrogate models could also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make multiscale analyses a viable industrial tool for large scale structural problems.

Composite↗
DOE OSTI2018

Scalable Preconditioners for Structure Preserving Discretizations of Maxwell Equations in First Order Form

Here, we report multiple physical time-scales can arise in electromagnetic simulations when dissipative effects are introduced through boundary conditions, when currents follow external time-scales, and when material parameters vary spatially. In such scenarios, the time-scales of interest may be much slower than the fastest time-scales supported by the Maxwell equations, therefore making implicit time integration an efficient approach. The use of implicit temporal discretizations results in linear systems in which fast time-scales, which severely constrain the stability of an explicit method, can manifest as so-called stiff modes. This study proposes a new block preconditioner for structure preserving (also termed physics compatible) discretizations of the Maxwell equations in first order form. The intent of the preconditioner is to enable the efficient solution of multiple-time-scale Maxwell type systems. An additional benefit of the developed preconditioner is that it requires only a traditional multigrid method for its subsolves and compares well against alternative approaches that rely on specialized edge-based multigrid routines that may not be readily available. Lastly, results demonstrate parallel scalability at large electromagnetic wave CFL numbers on a variety of test problems.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Electrochemical-mechanical coupling failure mechanism of composite cathode in all-solid-state batteries

Composite cathode composed of active particles and solid electrolytes (SEs) can considerably enlarge the particle-SE contact areas and achieve high areal loadings in all-solid-state batteries (ASSBs). However, the challenging interfacial instability and particle damage problems remain unsolved. Herein, we establish a 3D electrochemical-mechanical coupled model to investigate the underlying failure mechanism by considering the governing electrochemical and physics processes. Micro-scale heterogeneous primary particles with random crystallographic orientation and size inside the LiNi 1/3 Co 1/3 Mn 1/3 O 2 (NCM111) secondary particle of the model result in the anisotropic Li diffusion and volume variation within the secondary particle, leading to significant nonuniformity of the Li concentration, and GPa-level stress distributions at primary particle boundaries, and finally causing the particle internal cracks. The particle volume shrinkage under the constraint of stiff Li 7 La 3 Zr 2 O 12 (LLZO) SE triggers the interface debonding (gap>50 nm) with increased interfacial impedance to degrade cell capacity. Higher C-rates result in larger residual stress (~100 MPa)/strain/debonding gap at dis-charging end, more likely to deteriorate the cell performance. Increasing the interfacial strength between the particle and SE can suppress the interface debonding but induces high stress (up to 10 GPa). In conclusion, results reveal the underlying mechanism of the electrochemical-mechanical coupling failure mechanism for composite cathode and provide promising guidance on the further improvement of a more robust composite cathode for ASSBs.

25 ENERGY STORAGE↗
NASA NTRS1990

An approach for relating the results of quantitative nondestructive evaluation to intrinsic properties of high-performance materials

One of the most difficult problems the manufacturing community has faced during recent years has been to accurately assess the physical state of anisotropic high-performance materials by nondestructive means. In order to advance the design of ultrasonic nondestructive testing systems, a more fundamental understanding of how ultrasonic waves travel and interact within the anisotropic material is needed. The relationship between the ultrasonic and engineering parameters needs to be explored to understand their mutual dependence. One common denominator is provided by the elastic constants. The preparation of specific graphite/epoxy samples to be used in the experimental investigation of the anisotropic properties (through the measurement of the elastic stiffness constants) is discussed. Accurate measurements of these constants will depend upon knowledge of refraction effects as well as the direction of group velocity propagation. The continuing effort for the development of improved visualization techniques for physical parameters is discussed. Group velocity images are presented and discussed. In order to fully understand the relationship between the ultrasonic and the common engineering parameters, the physical interpretation of the linear elastic coefficients (the quantities that relate applied stresses to resulting strains) are discussed. This discussion builds a more intuitional understanding of how the ultrasonic parameters are related to the traditional engineering parameters.

Miller, James G.↗
NASA NTRS2003

Automated Finite Element Analysis of Elastically-Tailored Plates

A procedure for analyzing and designing elastically tailored composite laminates using the STAGS finite element solver has been presented. The methodology used to produce the elastic tailoring, namely computer-controlled steering of unidirectionally reinforced composite material tows, has been reduced to a handful of design parameters along with a selection of construction methods. The generality of the tow-steered ply definition provides the user a wide variety of options for laminate design, which can be automatically incorporated with any finite element model that is composed of STAGS shell elements. Furthermore, the variable stiffness parameterization is formulated so that manufacturability can be assessed during the design process, plus new ideas using tow steering concepts can be easily integrated within the general framework of the elastic tailoring definitions. Details for the necessary implementation of the tow-steering definitions within the STAGS hierarchy is provided, and the format of the ply definitions is discussed in detail to provide easy access to the elastic tailoring choices. Integration of the automated STAGS solver with laminate design software has been demonstrated, so that the large design space generated by the tow-steering options can be traversed effectively. Several design problems are presented which confirm the usefulness of the design tool as well as further establish the potential of tow-steered plies for laminate design.

Jegley, Dawn C.↗
NASA NTRS2017

Aeroelastic Modeling of X-56A Stiff-Wing Configuration Flight Test Data

Aeroelastic stability and control derivatives for the X-56A Multi-Utility Technology Testbed (MUTT), in the stiff-wing configuration, were estimated from flight test data using the output-error method. Practical aspects of the analysis are discussed. The orthogonal phase-optimized multisine inputs provided excellent data information for aeroelastic modeling. Consistent parameter estimates were determined using output error in both the frequency and time domains. The frequency domain analysis converged faster and was less sensitive to starting values for the model parameters, which was useful for determining the aeroelastic model structure and obtaining starting values for the time domain analysis. Including a modal description of the structure from a finite element model reduced the complexity of the estimation problem and improved the modeling results. Effects of reducing the model order on the short period stability and control derivatives were investigated.

Grauer, Jared A.↗
DOE OSTI2025

A scalable multidimensional fully implicit solver for Hall magnetohydrodynamics

We propose an optimally performant fully implicit algorithm for the Hall magnetohydrodynamics (HMHD) equations based on multigrid-preconditioned Jacobian-free Newton-Krylov methods. HMHD is a challenging system to solve numerically because it supports stiff fast dispersive waves. The preconditioner is formulated using an operator-split approximate block factorization (Schur complement), informed by physics insight. We use a vector-potential formulation (instead of a magnetic field one) to allow a clean segregation of the problematic $\nabla$ x $\nabla$ x operator in the electron Ohm's law subsystem. This segregation allows the formulation of an effective damped block-Jacobi smoother for multigrid. We demonstrate by analysis that our proposed block-Jacobi iteration is convergent and has the smoothing property. The resulting HMHD solver is verified linearly with wave propagation examples, and nonlinearly with the GEM challenge reconnection problem by comparison against another HMHD code. We demonstrate the excellent algorithmic and parallel performance of the algorithm up to 16384 MPI tasks in two dimensions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1993

A multigrid solver for the semiconductor equations

We present a multigrid solver for the exponential fitting method. The solver is applied to the current continuity equations of semiconductor device simulation in two dimensions. The exponential fitting method is based on a mixed finite element discretization using the lowest-order Raviart-Thomas triangular element. This discretization method yields a good approximation of front layers and guarantees current conservation. The corresponding stiffness matrix is an M-matrix. 'Standard' multigrid solvers, however, cannot be applied to the resulting system, as this is dominated by an unsymmetric part, which is due to the presence of strong convection in part of the domain. To overcome this difficulty, we explore the connection between Raviart-Thomas mixed methods and the nonconforming Crouzeix-Raviart finite element discretization. In this way we can construct nonstandard prolongation and restriction operators using easily computable weighted L(exp 2)-projections based on suitable quadrature rules and the upwind effects of the discretization. The resulting multigrid algorithm shows very good results, even for real-world problems and for locally refined grids.

Bachmann, Bernhard↗
NASA NTRSDate not supplied

Stiffness and Fatigue Life Estimator for Polymer Composite Laminates Using Machine Learning

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, Python-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been established. Results show that both neural net type algorithms can provide an excellent estimate of initial laminate stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminates (PMCs). RNNs are better able to capture the shape of the fatigue curve of a laminate. The resulting tool and GUI can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. Further, the associated surrogate models can also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make micromechanics-based multiscale analyses a viable industrial tool for large scale structural problems.

multiscale analysis↗
NASA NTRS2023

Stiffness and Fatigue Life Estimator for Polymer Composite Laminates Using Machine Learning

Machine learning (ML) models are increasingly being used in many engineering fields due to the advancements in ML algorithms and availability of high-speed computing power. One of the most popular ML class of models is artificial neural networks (ANN). ML is increasingly being used in the design and analysis of composite materials and structures, specifically in the constitutive modeling of composite materials with the focus on greatly accelerating multiscale analyses of composite materials and structures through development of surrogate models. Towards that end, Python-based neural nets have been developed to predict initial stiffness and fatigue life of an eight-ply symmetric polymer matrix composite laminate. Two types of neural networks, a Multilayer Perceptron (MLP) and a Recurrent Neural Network (RNN), have been established. Results show that both neural net type algorithms can provide an excellent estimate of initial laminate stiffness as well as fatigue life of eight-ply symmetric polymer matrix composite laminates (PMCs). RNNs are better able to capture the shape of the fatigue curve of a laminate. The resulting tool and GUI can be very useful for system level studies to obtain an estimate of desired properties and life of PMC composite laminates. Further, the associated surrogate models can also be used in composite multiscale analyses to replace the actual physics-based calculations at lower scales and thereby significantly increase the computational efficiency of such analyses and thus make micromechanics-based multiscale analyses a viable industrial tool for large scale structural problems.

multiscale analysis↗
DOE OSTI2017

Deposition of Ti{sub 2}AlC Thin Film

Future nuclear fission and fusion reactor designs require materials that can withstand long-term operation in extreme environments of high temperature, corrosion intermedia, plasma and fast neutron fluences. MAX phase materials have composition of the form M{sub n+1}AX{sub n} (n = 1-6) where M is an early transition metal, A is often an A-group element, mostly IIIA or IVA, and X is either carbon or nitrogen. They belong to a class of hexagonal structure ternary-layered materials. The main characteristic of the MAX phases is their structure which composes the stacking of n 'ceramic' M-X planes interposed with a 'metallic' A layer. Because of the 'mixed' structure, the MAX phases exhibit a combination of excellent properties of both ceramics and metals: high decomposition temperature, elastic stiffness, high oxidation resistance from ceramics as well as high thermal shock resistance, high thermal and electrical conductivities, and good machinability from metals. MAX phases also show great potential in tolerating radiation damage with both high irradiation tolerance and good self-healing abilities because of its unique structure. MAX phase thin films and coatings have been investigated in recent years. In particular, Ti{sub 2}AlC films have attracted attention because they possess great elastic properties, high temperature oxidation tolerance and excellent corrosion behavior. Therefore, Ti{sub 2}AlC films have been fabricated by several researchers. However, in the deposition of Ti{sub 2}AlC coatings, problems have arisen related to phase purity during sputtering from three elements (Ti, Al, C) targets onto substrates at a high temperature. Recent reports on reactive sputtering deposition of MAX phase carbides and nitrides show that the pure phase films (Ti{sub 2}AlC and Ti{sub 2}AlN) could be deposited at relatively low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Nonlinear analysis of NPP safety against the aircraft attack

The paper presents the nonlinear probabilistic analysis of the reinforced concrete buildings of nuclear power plant under the aircraft attack. The dynamic load is defined in time on base of the airplane impact simulations considering the real stiffness, masses, direction and velocity of the flight. The dynamic response is calculated in the system ANSYS using the transient nonlinear analysis solution method. The damage of the concrete wall is evaluated in accordance with the standard NDRC considering the spalling, scabbing and perforation effects. The simple and detailed calculations of the wall damage are compared.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1974

Influence of thermal distortion on the anomalous behavior of a gravity gradient satellite

Consideration of the problem of determining the influence of solar heating on the low-frequency dynamic stability of a gravity-gradient satellite. The scope of the effort includes the development of a computer program that uses a quasi-static approach for describing a satellite's unsteady orbital motion. The essential feature of the quasi-static approach is that the satellite's long, slender booms reach their thermal equilibrium position solely as a result of thermal bending without consideration of the dynamic effects of boom vibration. A nonlinear analytical model and a corresponding computer program have been developed to study the effect of absorptivity, sun angle, and hinge stiffness on the stability of a satellite's motion.

Goldman, R. L.↗